See Full Document Text
Official Journal EN
of the European Union L series
2025/1353 20.11.2025
COMMISSION DELEGATED REGULATION(EU) 2025/1353
of 1 July 2025
amending Delegated Regulation (EU) 2023/2534 on household tumble dryers regarding information
on repairability and clarifying some aspects of the measurement and calculation methods, the
product information sheet, the technical documentation and the verification procedure
(Text with EEA relevance)
THE EUROPEAN COMMISSION,
Having regard to the Treaty on the Functioning of the European Union,
Having regard to Regulation (EU) 2017/1369 of the European Parliament and of the Council of 4 July 2017 setting a
framework for energy labelling and repealing Directive 2010/30/EU(1), and in particular Article 16(1) thereof,
Whereas:
(1) Commission Delegated Regulation (EU) 2023/2534(2) lays down harmonised requirements for the labelling of
household tumble dryers, enabling customers to make informed purchasing decisions based on the energy efficiency
and supplementary information about the appliances. Article 3 of that Regulation also specifies the content and
format of the product information sheet and technical documentation and requires suppliers to enter the relevant
parameters in the European Product Registry for Energy Labelling (EPREL).
(2) It is important to address the significant decrease in the lifespan of household tumble dryers over the last 15 years,
which has prompted an increase in the rate of production to compensate for the shorter lifetime. Providing
information on the repairability of tumble dryers through a repairability index could generate several environmental,
social and economic benefits by encouraging consumers to choose more repairable products. The repairability index
should be calculated on the basis of parameters that are relevant for assessing the ease of repair of a household tumble
dryer.
(3) As from 1 January 2027, any household tumble dryer placed on the market should be accompanied by a label and a
product information sheet containing repairability information. In order to ensure a smooth introduction of the
repairability index, suppliers could provide labels that include the repairability information in advance of the
mandatory deadline of 1 January 2027, instead of labels without the repairability information.
(4) Since the implementation of a repairability index does not involve a rescaling of the label, dealers should be allowed,
after 1 January 2027 to sell, without limitation of time household tumble dryers placed on the market before that
date, with labels that do not include the repairability index.
(5) In order to improve repairability of household tumble dryers, an additional element should be included in the review
provided for by Article 7 of Delegated Regulation (EU) 2023/2534, namely the assessment of the possibility to
include heat pumps among the priority parts taken into account when calculating the repairability index.
(6) In order to ensure legal certainty relevant definitions regarding the repairability index and the average final moisture
content should be added.
(7) In order to help consumers to make informed choices about household tumble dryers degree of repair and
maintenance, the relevant repairability class should be included in the energy labels for both condenser and non-
condenser household tumble dryers, ranging from A to E, where the top class A corresponds to household tumble
dryers with the best repairability indexes and the lower class E to household tumble dryers with the worst
repairability indexes.
(1) OJ L 198, 28.7.2017, p. 1, ELI: http://data.europa.eu/eli/reg/2017/1369/oj.
(2) Commission Delegated Regulation (EU) 2023/2534 of 13 July 2023 supplementing Regulation (EU) 2017/1369 of the European
Parliament and of the Council with regard to energy labelling of household tumble dryers and repealing Commission Delegated
Regulation (EU) No 392/2012 (OJ L, 2023/2534, 22.11.2023, ELI: http://data.europa.eu/eli/reg_del/2023/2534/oj).
ELI: http://data.europa.eu/eli/reg_del/2025/1353/oj 1/27EN
OJ L, 20.11.2025
(8) The term ‘logo’ should be replaced by ‘pictogram’ in the description of the label provided in Annex III, to be
consistent with other delegated acts on energy labelling. Furthermore, the reference to the EU Ecolabel should be
deleted from Annex III, since the EU Ecolabel is no longer awarded.
(9) A method for the calculation of the repairability index of household tumble dryers, allowing to assign a repairability
class to each model of household tumble dryers, should be defined.
(10) The calculation of the repairability index should be carried out through a formula based on specific scoring
parameters which have been considered relevant to determine the easiness of repair for each model of household
tumble dryer. Those scoring parameters are the disassembly depth, the fasteners type, the tools type and the repair
information.
(11) Except for the repair information, which must be assessed at product level, the other three scoring parameters should
be evaluated at the level of the part of the household tumble dryer to be replaced. For this reason, priority parts have
been selected and included in the formula of each scoring parameter, with a weighted average reflecting the relevance
of each priority part in terms of sales and failure rates.
(12) The description of the disassembly steps used to calculate the disassembly depth scoring parameter, should be
consistent with the repair and maintenance information to be provided to professional repairers.
(13) It is appropriate to remove from the information to be provided in the technical documentation of the product, the
details of the calculation method of the average final moisture content of the eco programme which were originally
set in Annex IV, point 1(g) to Delegated Regulation (EU) 2023/2534. It has been noticed that obtaining 0 % value in
the average final moisture content is frequently accompanied by undesired negative side effects, in terms of textiles
heat damage from overdrying and excessive consumption of energy, which are to be avoided. Instead, the
measurement and calculation methods provided for in the harmonised standards should be used to calculate this
parameter as these provide for appropriate tolerances.
(14) In order to ensure consumers informed choices and encourage sustainable consumption, information on the
repairability index and the partial scores for each of the scoring parameters should be part of the product
information sheet. To avoid unnecessary administrative burden for suppliers, only changes in the global score of the
repairability index of a product should be deemed relevant for the definition of a new model. On the opposite,
changes in the partial calculations of the scoring parameters that do not alter the global reparability index are
deemed not relevant.
(15) In order to avoid confusion for suppliers and market surveillance authorities, the content of the technical
documentation including the relevant reparability information should be clarified.
(16) Delegated Regulation (EU) 2023/2534 should therefore be amended accordingly,
HAS ADOPTED THIS REGULATION:
Article 1
Amending provisions
Delegated Regulation (EU) 2023/2534 is amended as follows:
(1) Article 3 is amended as follows:
(a) paragraph 1 is replaced by the following:
‘1. Suppliers shall ensure that:
(a) from 1 March 2025 to 31 December 2026:
(i) each household tumble dryer is supplied with a printed label in the format and containing the
information set out in Annex III and, for a multi-drum household tumble dryer, in accordance
with Annex X;
(ii) the values for the parameters of the product information sheet, as set out in Annex V, are entered in
the public part of the product database;
2/27 ELI: http://data.europa.eu/eli/reg_del/2025/1353/ojEN
OJ L, 20.11.2025
(b) from 1 July 2025 to 31 December 2026:
(i) the content of the technical documentation set out in Annex VI is entered in the product database;
(ii) an electronic label in the format and containing the information as set out in Annex III is made
available to dealers for each model of household tumble dryer;
(iii) an electronic product information sheet as set out in Annex V is made available to dealers for each
model of household tumble dryer;
(iv) where specifically requested by the dealer, the product information sheet as set out in Annex V is
made available in printed form;
(c) from 1 January 2027:
(i) each household tumble dryer is supplied with a printed label in the format and containing the
information set out in Annex IIIa and, for a multi-drum household tumble dryer, in accordance
with Annex X;
(ii) the values for the parameters of the product information sheet as set out in Annex Va are entered in
the public part of the product database;
(iii) the content of the technical documentation set out in Annex VIa, except the information referred
to in points 1(h) and 1(i) of that Annex, is entered in the product database;
(iv) an electronic label in the format and containing the information set out in Annex IIIa is made
available to dealers for each model of household tumble dryer;
(v) an electronic product information sheet, as set out in Annex Va, is made available to dealers for
each model of household tumble dryer;
(vi) where specifically requested by the dealer, the product information sheet as set out in Annex Va is
made available in printed form;
(d) from 1 July 2025:
(i) any visual advertisement concerning a specific model of household tumble dryer gives the energy
efficiency class and range of energy efficiency classes available on the label in accordance with
Annexes VII and VIII;
(ii) any technical promotional material concerning a specific model of household tumble dryer,
including technical promotional material on the internet, which describes its specific technical
parameters, gives the energy efficiency class of that model and the range of energy efficiency
classes available on the label, in accordance with Annex VII.’;
(b) the following paragraph 1a is inserted:
‘1a. By way of derogation from paragraph 1, points (a) and (b), during the period, from 24 November 2025
to 31 December 2026, suppliers may fulfil their obligations set out in paragraph 1, points (a) and (b) in the
way set out in paragraph 1, point (c).’;
(2) in Article 4, point (a) is replaced by the following:
‘(a) each household tumble dryer, at the point of sale, including at trade fairs, bears the label provided by suppliers
in accordance with Article 3(1), points (a)(i) or (c)(i), with the label being displayed for built-in appliances in
such a way as to be clearly visible, and for all other appliances in such a way as to be clearly visible on the
outside on the front or top of the household tumble dryer;’;
(3) Article 7 is amended as follows:
(a) paragraph 1 is replaced by the following:
‘The Commission shall review this Regulation in the light of technological progress and present the results of
that review including, if appropriate, a draft proposal, to the Ecodesign Forum by 1 January 2030.
ELI: http://data.europa.eu/eli/reg_del/2025/1353/oj 3/27EN
OJ L, 20.11.2025
The review shall in particular assess the following elements:
(a) the improvement potential with regard to the energy consumption, functional and environmental
performance of household tumble dryers;
(b) the effectiveness of existing measures in prompting end-users to purchase appliances that are more
energy- and resource-efficient and to use more energy- and resource-efficient programmes;
(c) the scope for addressing circular economy objectives;
(d) the appropriateness to include the heat pump in the list of priority parts for the purpose of calculating
the repairability index.’;
(b) paragraph 2 is deleted;
(4) in Article 10, the second paragraph is replaced by the following:
‘It shall apply from 1 July 2025. However, Article 9 shall apply from 1 January 2024 and Article 3(1) and (1a) shall
apply as set out therein.’;
(5) Annexes I, II and III are amended in accordance with Annex I to this Regulation;
(6) the text set out in Annex II to this Regulation, is inserted as Annex IIIa;
(7) Annexes IV and V are amended in accordance with Annex III to this Regulation;
(8) the text set out in Annex IV to this Regulation is inserted as Annex Va;
(9) Annex VI is amended in accordance with Annex V to this Regulation;
(10) the text set out in Annex VI to this Regulation is inserted as Annex VIa;
(11) Annexes VII, VIII, IX and X are amended in accordance with Annex VII to this Regulation.
Article 2
Entry into force and application
This Regulation shall enter into force on the fourth day following that of its publication in the Official Journal of the European
Union.
This Regulation shall be binding in its entirety and directly applicable in all Member States.
Done at Brussels, 1 July 2025.
For the Commission
The President
Ursula VON DER LEYEN
4/27 ELI: http://data.europa.eu/eli/reg_del/2025/1353/ojEN
OJ L, 20.11.2025
ANNEX I
Annexes I, II and III to Delegated Regulation (EU) 2023/2534 are amended as follows:
(1) in Annex I, the following points are added:
‘(27) “average final moisture content” means the average of the final moisture content for the eco programme at
full and at half load;
(28) “spare part” means a separate part that can replace a part with the same or similar function in a household
tumble dryer;
(29) “priority part” means a spare part used in the calculations of the repairability index set out in Section 5 of
Annex IV;
(30) “main printed circuit board” means the board managing directly or indirectly the electric and electronic
components integrated in the appliance;
(31) “disassembly” means a process whereby a product is separated into its parts and/or components in such a
way that it could subsequently be reassembled and made operational;
(32) “fastener” means a hardware device or substance that mechanically, magnetically or by other means
connects or fixes two or more objects, parts or pieces, including a hardware device which in addition serves
an electrical function;
(33) “reusable fastener” means a fastener that can be completely reused in the reassembly for the same purpose
and that does no damage either the product or the fastener itself during the disassembly or reassembly
process in a way that makes their multiple reuse impossible;
(34) “removable fastener” means a fastener that is not a reusable fastener, but which removal does not damage
the product, or leave residue, which precludes reassembly;
(35) “resupplied fastener” means a removable fastener that is supplied with the spare part which it is intended to
connect or fix; adhesives shall be considered resupplied fasteners if they are supplied with the spare part in a
quantity that is sufficient for the reassembly;
(36) “step” means an operation that finishes with the removal of a part (or bundle) or with a change of tool,
including any placement of a part away from its initial location where the removal entails partial
disconnection or unplugging;
(37) “commercially available tool” means a tool that is available for purchase by the general public and is neither
a basic tool nor a proprietary tool;
(38) “basic tool” means a screwdriver for slotted heads, a screwdriver for cross recess screws, a screwdriver for
hexalobular recess heads, a hexagon socket key, a combination wrench, combination pliers, combination
pliers for wire stripping and terminal crimping, half round nose pliers, diagonal cutters, multigrip pliers,
locking pliers, a prying lever, tweezers, magnifying glass, a spudger and a pick;
(39) “proprietary tool” means tool that is not available for purchase by the general public or for which any
applicable patents are not available to licence under fair, reasonable and non-discriminatory terms;
(40) “professional repairer” means an operator or undertaking that provides services of repair and professional
maintenance of household tumble dryers.’;
ELI: http://data.europa.eu/eli/reg_del/2025/1353/oj 5/27EN
OJ L, 20.11.2025
(2) in Annex II, the following Section 4 is added:
‘4. REPAIRABILITY CLASS
The repairability class of a household tumble dryer shall be determined on the basis of the repairability index, as
set out in Table 3a. The repairability index shall be determined in accordance with Section 5 of Annex IV.
Table 3a
Repairability class
Repairability class Repairability index (R)
A (most repairable) R > 9,00
B 7,00 ≤ R ≤ 9,00
C 5,00 ≤ R < 7,00
D 3,00 ≤ R < 5,00
E (least repairable) R < 3,00’
(3) Annex III is amended as follows:
(a) in Section A, point 1.1 is amended as follows:
(i) point V is replaced by the following:
‘V the energy efficiency class determined in accordance with Annex II;’;
(ii) points VII and VIII are replaced by the following:
‘VII condensation efficiency class determined in accordance with Annex II, with relevant pictogram and
value rounded to the nearest integer and calculated in accordance with Annex IV;
VIII acoustic airborne noise emission class of the drying cycle of the eco programme, with relevant
pictogram and value in dB(A), determined in accordance with Section 4 of Annex IV;’;
(iii) point 1.2 is deleted;
(b) in Section B, point 1.1 is amended as follows:
(i) point V is replaced by the following:
‘V the energy efficiency class determined in accordance with Annex II;’;
(ii) point VII is replaced by the following:
‘VII acoustic airborne noise emission class of the drying cycle of the eco programme, with relevant
pictogram and value in dB(A), determined in accordance with Section 4 of Annex IV;’;
(iii) point 1.2 is deleted.
6/27 ELI: http://data.europa.eu/eli/reg_del/2025/1353/ojEN
OJ L, 20.11.2025
ANNEX II
‘ANNEX IIIa
LABEL WITH REPAIRABILITY INFORMATION
A. Label for condenser tumble dryers with repairability class pictogram
1. LABEL FOR CONDENSER TUMBLE DRYERS WITH REPAIRABILITY CLASS PICTOGRAM
Figure 4a
The following information shall be included in the label:
I QR code;
II trademark;
III model identifier;
IV scale of energy efficiency classes from A to G;
V the energy efficiency class determined in accordance with Annex II;
VI weighted average energy consumption per 100 drying cycles in kWh, rounded to the nearest integer and calculated in
accordance with Annex IV; in case of gas-fired tumble dryers, the weighted average energy consumption (gas and
electricity) per 100 drying cycles in kWh, rounded to the nearest integer and calculated in accordance with Annex IV;
VII repairability class determined in accordance with Annex II, calculated in accordance with Annex IV;
ELI: http://data.europa.eu/eli/reg_del/2025/1353/oj 7/27EN
OJ L, 20.11.2025
VIII condensation efficiency class determined in accordance with Annex II, with relevant pictogram and value rounded to
the nearest integer and calculated in accordance with Annex IV;
IX acoustic airborne noise emission class of the drying cycle of the eco programme, with relevant pictogram and value
in dB(A), determined in accordance with Section 4 of Annex IV;
X rated capacity, in kg, for the eco programme at full load;
XI duration of the eco programme at full load in hours and minutes [h:min] rounded to the nearest minute;
XII the number of this Regulation, which is “2023/2534”.
2. LABEL DESIGN FOR CONDENSER TUMBLE DRYERS WITH REPAIRABILITY CLASS PICTOGRAM
Figure 4b
8/27 ELI: http://data.europa.eu/eli/reg_del/2025/1353/ojEN
OJ L, 20.11.2025
Whereby:
(a) the label shall be at least 96 mm wide and 192 mm high. Where the label is printed in a larger format, its content
shall nevertheless remain proportionate to the specifications in Figure 4b;
(b) the background shall be 100 % white;
(c) the typeface shall be Verdana;
(d) the dimensions and specifications of the elements in the label shall be as indicated in the label designs in this Annex;
(e) colours shall be CMYK – cyan, magenta, yellow and black following this example: 0,70,100,0: 0 % cyan, 70 %
magenta, 100 % yellow, 0 % black;
(f) the label shall fulfil all of the following requirements (numbers refer to Figure 4b):
the colours of the EU logo shall be as follows:
— the background: 100,80,0,0;
— the stars: 0,0,100,0;
the colour of the energy logo shall be: 100,80,0,0;
the QR code shall be 100 % black;
the trademark shall be 100 % black and in Bold 9 pt;
the model identifier shall be 100 % black and in Regular 9 pt;
the A to G scale shall be as follows:
(a) the letters in the arrows shall be 100 % white and in Bold 16 pt, and shall be centred on an axis at
4,5 mm from the left side of the arrows;
(b) the background colours of the arrows shall be as follows:
(i) A-class: 100,0,100,0;
(ii) B-class: 70,0,100,0;
(iii) C-class: 30,0,100,0;
(iv) D-class: 0,0,100,0;
(v) E-class: 0,30,100,0;
(vi) F-class: 0,70,100,0;
(vii) G-class: 0,100,100,0;
the internal dividers shall be 80 mm wide and have a weight of 0,5 pt. The colour of the dividers shall be 100
% black;
the energy efficiency class arrow shall be 100 % black. The letter inside the energy efficiency class arrow shall
be 100 % white and in Bold 26 pt, and it shall be positioned in the centre of the rectangular part of the arrow.
The energy efficiency class arrow and the corresponding arrow in the A to G scale shall be positioned in such
a way that their tips are aligned;
the value of the weighted energy consumption per 100 drying cycles shall be in Bold 28 pt; “kWh/” shall be in
Regular 18 pt; the number “100” in the icon representing 100 drying cycles shall be in Regular 14 pt. The text
shall be centred in the column and in 100 % black;
the pictograms shall be as shown in the label design and as follows:
(a) the lines of the pictograms shall have a weight of 1,2 pt and they and the texts (numbers and units) shall
be 100 % black;
(b) the A to D scales of the condensation efficiency pictogram and of the acoustic airborne noise emission
pictogram shall be aligned on a vertical axis on the left side of the icon, with the letter of the applicable
class in Bold 12 pt and the other letters of the rest of the classes in Regular 8 pt;
ELI: http://data.europa.eu/eli/reg_del/2025/1353/oj 9/27EN
OJ L, 20.11.2025
(c) the number of the condensation efficiency pictogram shall be in Bold 9 pt and the unit in Regular 9 pt,
with the number and the unit next to each other and centred inside the pictogram;
(d) the A to E scale of the repairability class pictogram shall be aligned on a vertical axis on the left side of
the icon, with the letter of the applicable class in Bold 12 pt and the other letters of the rest of the
classes in Regular 8 pt;
(e) the number of the acoustic airborne noise emission pictogram shall be in Bold 12 pt and the unit in
Regular 9 pt, with the number and the unit next to each other and centred inside the pictogram;
(f) the number of the rated capacity pictogram shall be in Bold 16 pt and the unit in Regular 12 pt, with
the number and the unit next to each other and centred under the pictogram;
(g) the number of the duration of the eco programme pictogram shall be in Bold 16 pt and it shall be
centred under the pictogram;
the number of the Regulation shall be 100 % black and in Regular 6 pt.
B. Label for non-condenser tumble dryers with repairability class pictogram
1. LABEL FOR NON-CONDENSER TUMBLE DRYERS WITH REPAIRABILITY CLASS PICTOGRAM
Figure 4c
The following information shall be included in the label:
I QR code;
II trademark;
III model identifier;
IV scale of energy efficiency classes from A to G;
10/27 ELI: http://data.europa.eu/eli/reg_del/2025/1353/ojEN
OJ L, 20.11.2025
V the energy efficiency class determined in accordance with Annex II;
VI weighted average energy consumption per 100 drying cycles in kWh, rounded to the nearest integer and calculated in
accordance with Annex IV; in case of gas-fired tumble dryers, the weighted average energy consumption (gas and
electricity) per 100 drying cycles in kWh, rounded to the nearest integer and calculated in accordance with Annex IV;
VII repairability class determined in accordance with Annex II, calculated in accordance with Annex IV;
VIII acoustic airborne noise emission class of the drying cycle of the eco programme, with relevant pictogram and value
in dB(A), determined in accordance with Section 4 of Annex IV;
IX rated capacity, in kg, for the eco programme at full load;
X duration of the eco programme at full load in hours and minutes [h:min] rounded to the nearest minute;
XI the number of this Regulation, which is “2023/2534”.
2. LABEL DESIGN FOR NON-CONDENSER TUMBLE DRYERS WITH REPAIRABILITY CLASS PICTOGRAM
Figure 4d
ELI: http://data.europa.eu/eli/reg_del/2025/1353/oj 11/27EN
OJ L, 20.11.2025
Whereby:
(a) the label shall be at least 96 mm wide and 192 mm high. Where the label is printed in a larger format, its content
shall nevertheless remain proportionate to the specifications in Figure 4d;
(b) the background shall be 100 % white;
(c) the typeface shall be Verdana;
(d) the dimensions and specifications of the elements in the label shall be as indicated in the label designs in this Annex;
(e) colours shall be CMYK – cyan, magenta, yellow and black following this example: 0,70,100,0: 0 % cyan, 70 %
magenta, 100 % yellow, 0 % black;
(f) the label shall fulfil all of the following requirements (numbers refer to Figure 4d):
the colours of the EU logo shall be as follows:
— the background: 100,80,0,0;
— the stars: 0,0,100,0;
the colour of the energy logo shall be: 100,80,0,0;
the QR code shall be 100 % black;
the trademark shall be 100 % black and in Bold 9 pt;
the model identifier shall be 100 % black and in Regular 9 pt;
the A to G scale shall be as follows:
(a) the letters in the arrows shall be 100 % white and in Bold 16 pt, and shall be centred on an axis at
4,5 mm from the left side of the arrows;
(b) the background colours of the arrows shall be as follows:
(i) A-class: 100,0,100,0;
(ii) B-class: 70,0,100,0;
(iii) C-class: 30,0,100,0;
(iv) D-class: 0,0,100,0;
(v) E-class: 0,30,100,0;
(vi) F-class: 0,70,100,0;
(vii) G-class: 0,100,100,0;
the internal dividers shall be 80 mm wide and have a weight of 0,5 pt. The colour of the dividers shall be 100
% black;
the energy efficiency class arrow shall be 100 % black. The letter inside the energy efficiency class arrow shall
be 100 % white and in Bold 26 pt, and it shall be positioned in the centre of the rectangular part of the arrow.
The energy efficiency class arrow and the corresponding arrow in the A to G scale shall be positioned in such
a way that their tips are aligned;
the value of the weighted energy consumption per 100 drying cycles shall be in Bold 28 pt; “kWh/” shall be in
Regular 18 pt; the number “100” in the icon representing 100 drying cycles shall be in Regular 14 pt. The text
shall be centred in the column and in 100 % black;
the pictograms shall be as shown in the label design and as follows:
(a) the lines of the pictograms shall have a weight of 1,2 pt and they and the texts (numbers and units) shall
be 100 % black;
(b) the A to D scale of the acoustic airborne noise emission pictogram shall be aligned on a vertical axis on
the left side of the icon, with the letter of the applicable class in Bold 12 pt and the other letters of the
rest of the classes in Regular 8 pt;
(c) the A to E scale of the repairability class pictogram shall be aligned on a vertical axis on the left side of
the icon, with the letter of the applicable class in Bold 12 pt and the other letters of the rest of the
classes in Regular 8 pt;
12/27 ELI: http://data.europa.eu/eli/reg_del/2025/1353/ojEN
OJ L, 20.11.2025
(d) the number of the acoustic airborne noise emission pictogram shall be in Bold 12 pt and the unit in
Regular 9 pt, with the number and the unit next to each other and centred inside the pictogram;
(e) the number of the rated capacity pictogram shall be in Bold 16 pt and the unit in Regular 12 pt, with
the number and the unit next to each other and centred under the pictogram;
(f) the number of the duration of the eco programme pictogram shall be in Bold 16 pt and it shall be
centred under the pictogram;
the number of the Regulation shall be 100 % black and in Regular 6 pt.’
ELI: http://data.europa.eu/eli/reg_del/2025/1353/oj 13/27EN
OJ L, 20.11.2025
ANNEX III
Annexes IV and V to Delegated Regulation (EU) 2023/2534 are amended as follows:
(1) Annex IV is amended as follows:
(a) the third and fourth paragraphs are replaced by the following:
‘The eco programme as identifiable on the programme selection, on the display and through the network
connection, depending on the functionalities provided by the household tumble dryer, and with no further
modification of the final moisture content setting, shall be used for the measurement and calculation of the
EEI, the condensation efficiency, the programme duration and the airborne acoustic noise emissions. The
energy consumption, condensation efficiency and program duration shall also be measured concurrently.
The calculation of the weighted energy consumption, the weighted programme duration and the condensation
efficiency shall be done on the basis of three drying cycles at full load and four drying cycles at partial load.’;
(b) in Section 1, point (g) is deleted;
(c) the following Section 5 is added:
‘5. METHOD FOR THE CALCULATION OF THE REPAIRABILITY INDEX OF HOUSEHOLD TUMBLE DRYERS
The repairability index is an aggregated and normalised score, as a calculated value derived from four
scoring parameters where:
— S is the “Disassembly Depth” score;
DD
— S is the “Fasteners (type)” score;
F
— S is the “Tools (type)” score;
T
— S is the “Repair Information” score.
RI
The Repairability Index (R) shall be calculated as follows:
R¼0;450 × S + 0;225 × S + 0;225 × S + 0;100 × S
DD F T RI
and rounded to two decimal places.
The “Disassembly Depth” (S ), “Fasteners (type)” (S) and “Tools (type)” (S ) scores are based on the
DD F T
aggregation of the following priority parts level scores:
— WPis the water pump;
— Bis the drum bearing;
— DBis the drum belt;
— Dis the door;
— Mis the motor;
— MBis the main printed circuit board;
— Fis the fan;
— MCis the motor capacitor.
If any of the priority parts listed above is present in a product more than once, only the one which
delivers the lowest score shall be considered in the calculation of the “Disassembly Depth” (S ),
DD
“Fasteners (type)” (S) and “Tools (type)” (S ) scores. If one or more priority parts are not present in the
F T
product, those priority parts shall be removed from the formula of the scoring parameters where they
appear. In addition, the coefficients of the remaining priority parts in the formula of each scoring
parameter shall be divided by the complementary to 1 of the sum of the coefficients corresponding to
the priority parts not present in the product, so that the sum of the remaining coefficients shall always
be 1.
S , S and S shall be calculated on the basis of the description of the disassembly steps, the fasteners
DD F T
and the tools needed for each priority part.
14/27 ELI: http://data.europa.eu/eli/reg_del/2025/1353/ojEN
OJ L, 20.11.2025
The assessment of the repairability index, specifically S , S and S shall start on a product that is:
DD F T
— maintained as required in the user manual for daily use;
— fully assembled;
— standing, all side panels and the appliance cover freely accessible;
— disconnected from any supply and disposal.
After the assessment the product shall be fully reassembled.
5.1. The “Disassembly Depth” (S ) score shall be calculated as follows:
DD
SDD¼DDWP × 0;14 + DDB × 0;09 + DDDB × 0;25 + DDD × 0;08 + DDM × 0;05 + DDMB × 0;28 + DDF × 0;05 + DDMC × 0;06
Disassembly Depth (DD) assessment at part level
The Disassembly Depth score (DD) for each priority part (DD , DD , DD , DD , DD DD DD,
i WP B DB D M, MB, F
DD ) shall be set on the basis of the number of steps required to remove the priority part from the
MC
product (DD) with respect to the mean number of disassembly steps (MDS) for that priority part
without damaging the product. MDSfor each priority part is as follows:
— water pump: 16,1 steps;
— drum bearing: 18,9 steps;
— drum belt: 40,9 steps;
— door: 3 steps;
— motor: 49,4 steps;
— main printed circuit board: 13,7 steps;
— fan: 7,7 steps;
— motor capacitor: 24,9 steps.
Points ranging from 0 to 10 are assigned to DD for each priority part as follows:
i
— if DD≤ 0,70 × MDS, DD = 10 pt;
i
— if 0,70 × MDS< DD≤ 0,90 × MDS, DD = 7 pt;
i
— if 0,90 × MDS< DD≤ 1,10 × MDS, DD = 4 pt;
i
— if 1,10 × MDS< DD≤ 1,30 × MDS, DD = 1 pt;
i
— if DD> 1,30 × MDS, DD = 0 pt.
i
For the calculation of DD, the following rules shall apply:
— the step count for the disassembly of each priority part is completed when the target priority part is
separated and individually accessible. When the target priority part is part of an assembly or bundle
of parts, implying firstly the removal of the assembly or the bundle, the end of the disassembly
process takes place when the target priority part is separated and individually accessible;
— fasteners are not considered as a part;
— if, after the disassembly of a priority part, the disassembly of a further part requires partly the same
disassembly steps, the disassembly of this part may start with the first step that is different.
However, DD for that part shall be the total number of steps calculated from a fully assembled
product;
— where multiple tools need to be used simultaneously, the use of each tool counts as a separate step.
To grab a tool, to put a tool down and to remove a fastener are not considered the end of a step.
The hand shall not be considered as a tool;
— operations related to cleaning, removing traces or heating are counted as steps;
ELI: http://data.europa.eu/eli/reg_del/2025/1353/oj 15/27EN
OJ L, 20.11.2025
— DDshall be calculated on the basis of the description of the disassembly steps for each priority part
given in the technical documentation;
— where remote notification or authorisation of serial numbers is necessary for the full functionality
of the priority part, DDishall be zero.
5.2. The Fasteners type score (S) is calculated as follows:
F
S F¼FWP × 0;14 + FB × 0;09 + FDB × 0;25 + FD × 0;08 + F
M
× 0;05 + F
MB
× 0;28 + F
F
× 0;05 + F
MC
× 0;06
Fasteners (type) (F) assessment at part level
The “Fasteners (type)” scores (F) for each priority part (F , F , F , F , F F F, F ) are assigned
i WP B DB D M, MB, F MC
according to the level of removability and reusability of the fasteners used in the device assembly. Points
ranging from 0 to 10 are assigned to F for each priority part as follows:
i
— reusable fasteners F = 10 pt;
i
— resupplied fasteners at no cost, F = 7 pt;
i
— resupplied fasteners at additional costs, F = 4 pt;
i
— removable fasteners, F = 0 pt.
i
The identification of the type of fasteners is based on the description of each fastener type for the
disassembly process to remove the specific priority part given in the technical documentation.
In case different types of fasteners are encountered in the disassembly of a priority part, the lowest score
shall be considered.
5.3. The Tools type score (S ) shall be calculated as follows:
T
ST¼TWP × 0;14 + TB × 0;09 + T
DB
× 0;25 + T
D
× 0;08 + T
M
× 0;05 + T
MB
× 0;28 + T
F
× 0;05 + T
MC
× 0;06
Tools type (T) assessment at part level
The Tools type scores (T) for each priority part i(T , T , T , T , T , T , T, T ) are assigned according
i WP B DB D M MB F MC
to the complexity and availability of the tools needed for its replacement. Points ranging from 0 to 10 are
assigned to T for each priority part as follows:
i
— replacement possible with basic tools or without a tool, T = 10 pt;
i
— replacement possible with tools supplied with the spare part, T = 5 pt;
i
— replacement possible with commercially available tools, T = 0 pt.
i
The assessment of the type of tools is based on the disassembly process to remove the specific priority
part given in the technical documentation.
Where different types of tools are needed for the disassembly of a priority part, the lowest score shall be
considered.
5.4 Repair Information (RI) assessment at product level
The Repair Information score (S ) for the repair and maintenance information in point 5(1)(b) of
RI
Annex II of Regulation (EU) 2023/2533 shall be calculated at product level as follows:
— availability of repair information at no cost for professional repairers, S = 10 pt;
RI
— availability of repair information with a reasonable and proportionate fee for professional
repairers, S = 0 pt.
RI
A fee shall be considered reasonable if it does not discourage access to repair information by failing to
take into account the extent to which the professional repairer uses the information.’;
16/27 ELI: http://data.europa.eu/eli/reg_del/2025/1353/ojEN
OJ L, 20.11.2025
(2) Annex V is amended as follows:
(a) the first subparagraph is replaced by the following:
‘Pursuant to Article 3(1), point (a)(ii), until 31 December 2026 the supplier shall enter the information into the
product database as set out in Table 4. However, in accordance with Article 3(1a), suppliers may enter the
information required in Table 4a of Annex Va into the product database from 24 November 2025 instead of
the information required in Table 4.’;
(b) Table 4 is replaced by the following:
‘Table 4
Content, order and format of the product information sheet
Trademark(a)(c):
Model identifier(a):
Technology of tumble dryer [electric air-vented, electric heat pump condenser, electric conventional
condenser, gas-fired]
General product parameters:
Parameter Value Parameter Value
Rated capacity(b)(kg) x,x Dimensions(a)(c)(cm) Height x
Width x
Depth x
Energy Efficiency Index x,x Energy efficiency [A/B/C/D/E/F/G](d)
(EEI)(b) class(b)
Condensation efficiency xx Condensation [A/B/C/D](d)
(%)(b) efficiency class (if
(if applicable) applicable)(b)
Weighted energy x,xx
consumption in kWh per
drying cycle(h). Actual
energy consumption will
depend on how the
appliance is used.
Programme duration(b) Rated x:xx Type [built-in/free-standing]
(hours:minutes) capacity
Half x:xx
Acoustic airborne noise x Acoustic airborne [A/B/C/D](d)
emission(b)(dB(A) re 1 pW) noise emission class(b)
Off-mode (if applicable) (W) x,xx Standby mode (if x,xx
applicable) (W)
Delay start (W) (if applicable) x,xx Networked standby x,xx
(W) (if applicable)
For household tumble dryers equipped with a heat pump, the chemical name or
the accepted industry designation of the refrigerant gas used, without prejudice to
Regulation (EU) No 517/2014 on fluorinated greenhouse gases(1)(a)(c)
Weblink to information on spare parts availability for professional repairers and
https://xxx
end users(a)(c)(e)
ELI: http://data.europa.eu/eli/reg_del/2025/1353/oj 17/27EN
OJ L, 20.11.2025
Weblink to repair instructions for end-users(a)(c)(f) https://xxx
Weblink to indicative pre-tax prices(a)(c)(g) https://xxx
Minimum duration of the commercial guarantee offered by the supplier(a)(c)
(months)
Additional information(c)
Link to the supplier’s website, where the information in point 6 of Annex II to Commission Regulation
(EU) 2023/2533(c)(2)is found:
(1) Regulation (EU) No 517/2014 of the European Parliament and of the Council of 16 April 2014 on fluorinated
greenhouse gases and repealing Regulation (EC) No 842/2006 (OJ L 150, 20.5.2014, p. 195, ELI: http://data.europa.eu/
eli/reg/2014/517/oj).
(2) Commission Regulation (EU) 2023/2533 of 17 November 2023 implementing Directive 2009/125/EC of the European
Parliament and of the Council with regard to ecodesign requirements for household tumble dryers, amending
Commission Regulation (EU) 2023/826, and repealing Commission Regulation (EU) No 932/2012 (OJ L, 2023/2533,
22.11.2023, ELI: http://data.europa.eu/eli/reg/2023/2533/oj).
(a) This item shall not be considered relevant for the purpose of Article 2(6) of Regulation (EU) 2017/1369.
(b) For the eco programme.
(c) Changes to those items shall not be considered relevant for the purpose of Article 4(4) of Regulation (EU) 2017/1369.
(d) If the product database automatically generates the definitive content of that cell the supplier shall not enter those data.
(e) The suppliers’ obligation is to include the link to the webpage where the relevant information will be available. Effective
access to the website is nevertheless to be granted in accordance with the timeline and provisions laid down in point
5(1)(b) of Annex II to Regulation (EU) 2023/2533.
(f) The suppliers’ obligation is to include the link to the webpage where the relevant information will be available. Effective
access to the website is nevertheless to be granted in accordance with the timeline and provisions laid down in point
5(1)(d) of Annex II to Regulation (EU) 2023/2533.
(g) The suppliers’ obligation is to include the link to the webpage where the relevant information will be available. Effective
access to the website is nevertheless to be granted in accordance with the timeline and provisions laid down in point
5(1)(f) of Annex II to Regulation (EU) 2023/2533.
(h) For gas-fired tumble dryers calculated as the weighted average energy consumption per 100 drying cycles in accordance
with Section 1, point (f), of Annex IV of this Regulation, divided by 100.’
18/27 ELI: http://data.europa.eu/eli/reg_del/2025/1353/ojEN
OJ L, 20.11.2025
ANNEX IV
‘ANNEX Va
PRODUCT INFORMATION SHEET WITH REPAIRABILITY INFORMATION
Pursuant to Article 3(1), point (e)(ii), from 1 January 2027 the supplier shall enter the information as set out in Table 4a into
the product database. However, in accordance with Article 3(1a) of this Regulation, suppliers may enter the information
required in Table 4a into the product database from 24 November 2025 instead of the information required in Table 4 of
Annex V to this Regulation.
The user manual or other literature provided with the product shall clearly indicate the link to the model in the product
database as a human-readable Uniform Resource Locator (URL) or as a QR code or by providing the product registration
number.
Table 4a
Content, order and format of the product information sheet
Trademark(a)(c):
Model identifier(a):
Technology of tumble dryer [electric air-vented, electric heat pump condenser, electric conventional condenser,
gas-fired]
General product parameters:
Parameter Value Parameter Value
Rated capacity(b)(kg) x,x Dimensions(a)(c) Height x
(cm)
Width x
Depth x
Energy Efficiency Index x,x Energy efficiency [A/B/C/D/E/F/G](d)
(EEI)(b) class(b)
Condensation xx Condensation [A/B/C/D](d)
efficiency (%)(b) efficiency class (if
(if applicable) applicable)(b)
Weighted energy X,xx
consumption in kWh
per drying cycle(h).
Actual energy
consumption will
depend on how the
appliance is used.
Programme Rated x:xx Type [built-in/free-standing]
duration(b) capacity
(hours:minutes)
Half x:xx
Acoustic airborne x Acoustic airborne [A/B/C/D](d)
noise emission(b) noise emission
(dB(A) re 1 pW) class(b)
Off-mode (if x,xx Standby mode (if x,xx
applicable) (W) applicable) (W)
ELI: http://data.europa.eu/eli/reg_del/2025/1353/oj 19/27EN
OJ L, 20.11.2025
Delay start (W) (if x,xx Networked standby x,xx
applicable) (W) (if applicable)
For household tumble dryers equipped with a heat pump, the chemical
name or the accepted industry designation of the refrigerant gas used,
without prejudice to Regulation (EU) No 517/2014 on fluorinated
greenhouse gases(1)(a)(c)
Repairability information:
Repairability Class (based on the index below) [A/B/C/D/E](d)
Repairability Index(a) x,xx
Disassembly Depth (S ) score(a)(c) x,xx
DD
Fasteners type score (S)(a)(c) x,xx
F
Tools type score (S )(a)(c) x,xx
T
Repair information score (S )(a)(c) x,xx
RI
Weblink to information on spare parts availability for professional
https://xxx
repairers and end users(a)(c)(e)
Weblink to repair instructions for end-users(a)(c)(f) https://xxx
Weblink to indicative pre-tax prices(a)(c)(g) https://xxx
Minimum duration of the commercial guarantee offered by the
supplier(a)(c)(months)
Additional information(e)
Link to the supplier’s website, where the information in point 6 of Annex II to Commission Regulation
(EU) 2023/2533(e)(2)is found:
(1) Regulation (EU) No 517/2014 of the European Parliament and of the Council of 16 April 2014 on fluorinated greenhouse gases and
repealing Regulation (EC) No 842/2006 (OJ L 150, 20.5.2014, p. 195, ELI: http://data.europa.eu/eli/reg/2014/517/oj).
(2) Commission Regulation (EU) 2023/2533 of 17 November 2023 implementing Directive 2009/125/EC of the European Parliament
and of the Council with regard to ecodesign requirements for household tumble dryers, amending Commission Regulation
(EU) 2023/826, and repealing Commission Regulation (EU) No 932/2012 (OJ L, 2023/2533, 22.11.2023, ELI: http://data.europa.eu/
eli/reg/2023/2533/oj).
(a) This item shall not be considered relevant for the purpose of Article 2(6) of Regulation (EU) 2017/1369.
(b) For the eco programme.
(c) Changes to those items shall not be considered relevant for the purpose of Article 4(4) of Regulation (EU) 2017/1369.
(d) If the product database automatically generates the definitive content of that cell the supplier shall not enter those data.
(e) The suppliers’ obligation is to include the link to the webpage where the relevant information will be available. Effective access to the
website is nevertheless to be granted in accordance with the timeline and provisions laid down in point 5(1)(b) of Annex II to
Regulation (EU) 2023/2533.
(f) The suppliers’ obligation is to include the link to the webpage where the relevant information will be available. Effective access to the
website is nevertheless to be granted in accordance with the timeline and provisions laid down in point 5(1)(d) of Annex II to
Regulation (EU) 2023/2533.
(g) The suppliers’ obligation is to include the link to the webpage where the relevant information will be available. Effective access to the
website is nevertheless to be granted in accordance with the timeline and provisions laid down in point 5(1)(f) of Annex II to
Regulation (EU) 2023/2533.
(h) For gas-fired tumble dryers calculated as the weighted average energy consumption per 100 drying cycles in accordance with Section
1, point (f), of Annex IV of this Regulation, divided by 100.’
20/27 ELI: http://data.europa.eu/eli/reg_del/2025/1353/ojEN
OJ L, 20.11.2025
ANNEX V
Annex VI to Delegated Regulation (EU) 2023/2534 is amended as follows:
(1) point 1 is amended as follows:
(a) in the first subparagraph, the introductory wording is replaced by the following:
‘For electric household tumble dryers, the technical documentation referred to in Article 3(1), point (b)(i), shall
include the following information:’;
(b) point (g) is replaced by the following:
‘(g) the values for the technical parameters set out in Table 5 for the eco programme, which are considered as
the declared values for the purpose of the verification procedure set out in Annex IX.’;
(2) in Table 5, the header is replaced by the following:
‘Table 5
Declared technical parameters for electric household tumble dryers’;
(3) in point 2, the first subparagraph is replaced by the following:
‘For gas-fired tumble dryers, the technical documentation referred to Article 3(1), point (b)(i), shall include the
information listed in paragraph 1, points (a) to (f) of this Annex, and the information set out in Table 6 for the eco
programme. The values in Table 6 are considered as the declared values for the purpose of the verification procedure
in Annex IX.’.
(4) Table 6 is amended as follows:
(a) the header is replaced by the following:
‘Table 6
Declared technical parameters for gas-fired household tumble dryers’;
(b) the fourth row on the gas consumption of the eco programme at partial load is replaced by the following:
‘Gas consumption of the eco programme at partial load kWh/drying cycle X,XX’
(E )
gdry,½
(c) the tenth, eleventh and twelfth rows on the programme duration for the eco programme are replaced by the
following:
‘Programme duration for the eco programme at full load (T ) h:min X:XX
dry
Programme duration for the eco programme at partial load h:min X:XX
(T )
dry½
Weighted programme duration for the eco programme (T) h:min X:XX’
t
(5) point 3 is replaced by the following:
‘3. Where the information included in the technical documentation for a particular household tumble dryer has
been obtained:
(a) from a model that has the same technical characteristics relevant for the technical information to be
provided but is produced by a different supplier;
(b) by calculation on the basis of design or extrapolation from another model of the same or a different
supplier,
the technical documentation shall include the details of the calculation, the assessment undertaken by suppliers
to verify the accuracy of the calculation and, where appropriate, the declaration of identity between the models
of different suppliers.’.
ELI: http://data.europa.eu/eli/reg_del/2025/1353/oj 21/27EN
OJ L, 20.11.2025
ANNEX VI
‘ANNEX VIa
TECHNICAL DOCUMENTATION WITH REPAIRABILITY INFORMATION
1. For electric household tumble dryers, the technical documentation referred to in Article 3(1), point (c)(iii), shall
include the following information:
(a) a general description of the model allowing it to be unequivocally and easily identified;
(b) references to the harmonised standards applied or other measurement standards used;
(c) specific precautions to be taken when the model is assembled, installed, maintained or tested;
(d) the details and the results of calculations performed in accordance with Annex IV;
(e) testing conditions, where they are not described sufficiently in the references provided pursuant to point (b) of
this section;
(f) equivalent models, if any, including model identifiers;
(g) the values for the technical parameters set out in Table 6a for the eco programme, which are considered as the
declared values for the purpose of the verification procedure set out in Annex IX;
(h) a description of the disassembly steps for each priority part listed in Section 5 of Annex IV, including the tool(s)
and fastener(s) needed at each step, if any;
(i) the repair and maintenance information laid down in point 5(3)(e) of Annex II to Regulation (EU) 2023/2533.
The information provided pursuant to points (a) to (g) shall constitute the mandatory specific parts of the technical
documentation that the supplier is to enter into the product database, pursuant to Article 12(5) of Regulation
(EU) 2017/1369.
Table 6a
Declared technical parameters for electric household tumble dryers
Parameter Unit Value
Rated capacity for the eco programme, at 0,5 kg intervals (c) kg X,X
Energy consumption of the eco programme at full load (E ) kWh/drying cycle X,XX
dry
Energy consumption of the eco programme at partial load (E ) kWh/drying cycle X,XX
dry,½
Weighted energy consumption of the eco programme (E ) kWh/drying cycle X,XX
tC
Standard energy consumption of the eco programme (SE ) kWh/drying cycle X,XX
C
Energy Efficiency Index (EEI) — X,X
Programme duration for the eco programme at full load (T ) h:min X:XX
dry
Programme duration for the eco programme at partial load (T ) h:min X:XX
dry½
Weighted programme duration for the eco programme (T) h:min X:XX
t
Average condensation efficiency of the eco programme at full
% XX
load (C ) (if applicable)
dry
Average condensation efficiency of the eco programme at partial
% XX
load (C ) (if applicable)
dry½
22/27 ELI: http://data.europa.eu/eli/reg_del/2025/1353/ojEN
OJ L, 20.11.2025
Parameter Unit Value
Weighted condensation efficiency of the eco programme (C) (if
t % XX
applicable)
dB(A) with respect
Acoustic airborne noise emission during the eco programme X
to 1 pW
Power consumption in off mode (P) (if applicable) W X,XX
o
Power consumption in standby mode (P ) (if applicable) W X,XX
sm
Does “standby mode” include the display of information? — Yes/No
Power consumption in “standby mode” in condition of networked
W X,XX
standby (P ) (if applicable)
nsm
Power consumption in delay start (P ) (if applicable) W X,XX
ds
Repairability Index — X,XX
2. For gas-fired tumble dryers, the technical documentation referred to in Article 3(1) point (c)(iii), shall include the
information listed in paragraph 1, points (a) to (f), (h) and (i) of this Annex, and the information set out in Table 6b
for the eco programme. The values in Table 6b are considered as the declared values for the purpose of the
verification procedure in Annex IX.
The information provided pursuant to the first subparagraph of this point, except points (h) and (i), shall constitute
the mandatory specific parts of the technical documentation that the supplier is to enter into the database, pursuant
to Article 12(5) of Regulation (EU) 2017/1369.
Table 6b
Declared technical parameters for gas-fired household tumble dryers
Parameter Unit Value
Rated capacity for the eco programme, at 0,5 kg intervals (c) kg X,X
Gas consumption of the eco programme at full load (E ) kWh/drying cycle X,XX
gdry
Gas consumption of the eco programme at partial load (E ) kWh/drying cycle X,XX
gdry,½
Auxiliary electricity consumption of the eco programme at full
kWh/drying cycle X,XX
load
Auxiliary electricity consumption of the eco programme at kWh/drying cycle X,XX
partial load
Weighted energy consumption of the eco programme (E ) kWh/drying cycle X,XX
tC
Standard energy consumption of the eco programme (SE ) kWh/drying cycle X,XX
C
Energy Efficiency Index (EEI) — X,X
Programme duration for the eco programme at full load (T ) h:min X:XX
dry
Programme duration for the eco programme at partial load (T ) h:min X:XX
dry½
ELI: http://data.europa.eu/eli/reg_del/2025/1353/oj 23/27EN
OJ L, 20.11.2025
Parameter Unit Value
Weighted programme duration for the eco programme (T) h:min X:XX
t
Acoustic airborne noise emission during the eco programme dB(A) re 1 pW X
Power consumption in off mode (P) (if applicable) W X,XX
o
Power consumption in standby mode (P ) (if applicable) W X,XX
sm
Does “standby mode” include the display of information? — Yes/No
Power consumption in standby mode in condition of networked
W X,XX
standby (P ) (if applicable)
nsm
Power consumption in “delay start” (P ) (where applicable) W X,XX
ds
Repairability Index — X,XX
3. Where the information included in the technical documentation for a particular household tumble dryer has been
obtained:
(a) from a model that has the same technical characteristics relevant for the technical information to be provided
but is produced by a different supplier;
(b) by calculation on the basis of design or extrapolation from another model of the same or a different supplier,
the technical documentation shall include the details of the calculation, the assessment undertaken by suppliers to
verify the accuracy of the calculation and, where appropriate, the declaration of identity between the models of
different suppliers.’
24/27 ELI: http://data.europa.eu/eli/reg_del/2025/1353/ojEN
OJ L, 20.11.2025
ANNEX VII
Annexes VII, VIII, IX and X to Delegated Regulation (EU) 2023/2534 are amended as follows:
(1) in Annex VII, points 1 and 2 are replaced by the following:
‘1. In visual advertisements, for the purposes of ensuring conformity with the requirements laid down in
Article 3(1), point (d)(i), and in Article 4, point (c), the energy efficiency class and the range of energy
efficiency classes available on the label shall be shown as set out in point 4 of this Annex.
2. In technical promotional material, for the purposes of ensuring conformity with the requirements laid down in
Article 3(1), point (d)(ii), and in Article 4, point (d), the energy efficiency class and the range of energy efficiency
classes available on the label shall be shown as set out in point 4 of this Annex.’;
(2) Annex VIII is amended as follows:
(a) point 1 is replaced by the following:
‘1. The appropriate label made available by suppliers in accordance with Article 3(1), points (b)(ii) or (c)(iv),
as applicable, shall be shown on the display mechanism in proximity to the price of the product if the
price is shown, and in all other cases in proximity to the name or the picture of the product. The size
shall be such that the label is clearly visible and legible and shall be proportionate to the size specified in
Annex III or IIIa, as applicable. The label may be displayed using a nested display, in which case the image
used for accessing the label shall comply with the specifications laid down in point 2 of this Annex. If
nested display is applied, the label shall appear on the first mouse click, mouse roll-over or tactile screen
expansion on the image.’;
(b) point 3(b) is replaced by the following:
‘(b) the image shall link to the label set out in Annex III or in Annex IIIa, as applicable;’;
(c) point 4 is replaced by the following:
‘4. The electronic product information sheet made available by the supplier in accordance with Article 3(1),
points (b)(iii) or (c)(v), as applicable, shall be shown on the display mechanism in proximity to the price of
the product if the price is shown, and in all other cases in proximity to the name or the picture of the
product. The size shall be such that the product information sheet is clearly visible and legible. The
product information sheet may be displayed using a nested display or by referring to the product
database, in which case the link used for accessing the product information sheet shall clearly and legibly
indicate “Product information sheet”. If a nested display is used, the product information sheet shall
appear on the first mouse click, mouse roll-over or tactile screen expansion on the link.’;
(3) Annex IX is amended as follows:
(a) point 1 is replaced by the following:
‘1. The verification tolerances set out in Table 8 relate only to the verification of the declared values by
Member State authorities and shall not be used by the supplier as an allowed tolerance to establish these
values in the technical documentation or in interpreting these values with a view to achieving compliance
or to communicate better performance by any means.’;
(b) point 4(b)(iii) is replaced by the following:
‘(iii) the determined values, that is to say the values of the relevant parameters as measured in testing and the
values calculated from these measurements, comply with:
(a) the validity criteria set out in Table 7;
(b) the respective verification tolerances set out in Table 8.’;
ELI: http://data.europa.eu/eli/reg_del/2025/1353/oj 25/27EN
OJ L, 20.11.2025
(c) point 6 is replaced by the following:
‘6. Where the result referred to in point 4(b)(iii) is not achieved, the Member State authorities shall select
three additional units of the same model for testing. As an alternative, the three additional units selected
may be of one or more equivalent models. Concerning the repairability index, if the result referred to in
point 4(b)(iii) is not achieved, the Member State authorities shall select one additional unit of the same
model for testing.’;
(d) points 8 and 9 are replaced by the following:
‘8. The model shall be considered to comply with the applicable requirements where for the three units
referred to in point 6, the arithmetic mean of the determined values complies with the respective
verification tolerances set out in Table 8, except for the result of the repairability index, where the model
shall be considered to comply with the applicable requirements where for the additional unit referred to
in point 6, the determined value complies with the respective tolerance set out in Table 8.
9. Where the result referred to in point 8 is not achieved, the model and all equivalent models shall be
considered not in compliance with this Regulation, except for the result of the repairability index, where
the model shall be considered not in compliance with this Regulation.’;
(e) point 12 is replaced by the following:
‘12. The Member State authorities shall only apply the validity criteria set out in Table 7 and the verification
tolerances set out in Table 8 and shall only use the procedure set out in points 1 to 9 for the
requirements referred to in this Annex. For the parameters set out in Tables 7 and 8, no other validity
criteria or verification tolerances, such as those set out in harmonised standards or in any other
measurement method, shall be applied.’;
(f) Table 7 is replaced by the following:
‘Table 7
Validity criteria
Parameter Validity criteria
Average final moisture content of The determined value shall be measured and calculated and be lower
the eco programme μ than 1,5 %.’
t
(g) the following Table 8 is added:
‘Table 8
Verification tolerances
Parameter Verification tolerances
E and E The determined value(*)shall not exceed the declared value of E and
dry dry½ dry
E by more than 6 %.
dry½
Eg and Eg The determined value(*)shall not exceed the declared value of Eg
dry dry½ dry
and Eg by more than 6 %.
dry½
Eg and Eg The determined value(*) shall not exceed the declared value of Eg
dry,a dry½,a dry,a
and Eg by more than 6 %.
dry½,a
C The determined value(*)shall not be less than the declared value of C
t t
by more than 6 %.
T and T The determined value(*)shall not exceed the declared value of T and
dry dry½ dry
T by more than 6 %.
dry½
P The determined value(*)shall not exceed the declared value by more
o
than 0,10 W.
26/27 ELI: http://data.europa.eu/eli/reg_del/2025/1353/ojEN
OJ L, 20.11.2025
Parameter Verification tolerances
P The determined value(*)shall not exceed the declared value by more
sm
than 10 % if the declared value is higher than 1,00 W, or by more than
0,10 W if the declared value is lower than or equal to 1,00 W.
P The determined value(*)shall not exceed the declared value by more
ds
than 10 % where the declared value is higher than 1,00 W, or by more
than 0,10 W if the declared value is lower than or equal to 1,00 W.
Acoustic airborne noise emissions The determined value(*)shall not exceed the declared value by more
than 2 dB with respect to 1 pW.
Repairability index The determined value shall not be less than the declared value by more
than 4 %.
(*) Where three additional units are tested in accordance with point (6), the determined value means the arithmetic mean of
the values determined for those three additional units.’
(4) Annex X is amended as follows:
(a) in the first paragraph, the introductory wording is replaced by the following:
‘Following the measurement and calculation methods set out in Annex IV, each drum of a multi-drum
household tumble dryer shall be supplied with a label complying with the requirements set out in Annexes II
and III or IIIa, as applicable. Those requirements shall apply to each of the drums independently, except when
the drums are built in the same casing and can, in the eco programme, only operate simultaneously. In the
latter case, these provisions shall apply to the multi-drum household tumble dryer as a whole, as follows:’;
(b) the second paragraph is replaced by the following:
‘The product information sheet shall include and present jointly the information required under Annex V or
Annex Va, as applicable, for all the drums to which the provisions of this Annex apply. The technical
documentation shall include and present jointly the information required under Annex VI or Annex VIa, as
applicable, for all the drums to which the provisions of this Annex apply.’.
ELI: http://data.europa.eu/eli/reg_del/2025/1353/oj 27/27