Date: 2025-11-20 Category: Not Applicable State: Union Government Country: Europe

Commission Implementing Regulation (EU) 2025/2202 of 22 October 2025 amending Implementing Regulation (EU) 2022/1434 as regards administrative changes to the Union authorisation for the biocidal product family CMIT-MIT Aqueous 1.5-15, and correcting that Regulation

Issued by European Commission · Directorate-General for Health and Food Safety

Research with AI Agent Chat with Document Generate Summary Translate Helpful Share Add to Project Create Task

Executive Summary & Key Takeaways

                    **Executive Summary**
This document is a Commission Implementing Regulation amending Implementing Regulation (EU) 2022/1434. It concerns administrative changes to the Union authorization for the biocidal product family ‘CMIT-MIT Aqueous 1.5-15', and the correction of that Regulation. The regulation enters into force on the twentieth day following its publication in the Official Journal of the European Union.

**Key Points / Main Content**

*Administrative Changes and Corrections:*
   *   Corrects Implementing Regulation (EU) 2022/1434 by referencing ‘MC (Netherlands) 1 B.V.' as the authorization holder for the biocidal product family ‘CMIT-MIT Aqueous 1.5-15', consistent with the SPC in the Annex.
   *   Implements administrative changes notified by ‘MC (Netherlands) 1 B.V.’, including the addition of manufacturers, changes in manufacturer names, and changes to the address of the authorization holder.
   *   Replaces the Annex to Implementing Regulation (EU) 2022/1434 entirely with a revised version. This revision includes all administrative changes and minor editorial updates in the format used for biocidal products since February 2024.
   *   Article 1 of Implementing Regulation (EU) 2022/1434 is replaced to reflect the update authorization holder and the revised validity period (20 September 2022 until 31 August 2032).

*Biocidal Product Characteristics:*
   *  Remaining information in the summary of the biocidal product characteristics of ‘CMIT-MIT Aqueous 1.5-15', as set out in the Annex to Implementing Regulation (EU) 2022/1434, remain unchanged.

**Impact Analysis**

**Stakeholder:** MC (Netherlands) 1 B.V.

**Impact:** 
The company will be officially recognized as the authorization holder for the biocidal product family ‘CMIT-MIT Aqueous 1.5-15’. The administrative changes they requested regarding manufacturers and address have been implemented.

**Action Required:** 
Ensure compliance with the revised summary of the biocidal product characteristics as set out in the Annex, which include conditions of use.
                

Key Entities Referenced

Regulation (EU) No 528/2012: Regulation of the European Parliament and of the Council concerning the making available on the market and use of biocidal products. Implementing Regulation (EU) 2022/1434: Commission Implementing Regulation granting a Union authorisation for the biocidal product family 'CMIT-MIT Aqueous 1.5-15'. European Chemicals Agency ('the Agency'): The Agency is responsible for assessing administrative changes to the Union authorisation for the biocidal product family. Implementing Regulation (EU) No 354/2013: Commission Implementing Regulation on changes of biocidal products authorized in accordance with Regulation (EU) No 528/2012 of the European Parliament and of the Council. CMIT-MIT Aqueous 1.5-15: The biocidal product family which is the subject of the Union authorisation and the amendments described in the Regulation.

Official Source Record View Original Source →

See Full Document Text

                Official Journal EN
of the European Union L series
2025/2202 20.11.2025
COMMISSION IMPLEMENTING REGULATION(EU) 2025/2202
of 22 October 2025
amending Implementing Regulation (EU) 2022/1434 as regards administrative changes to the Union
authorisation for the biocidal product family ‘CMIT-MIT Aqueous 1.5-15’, and correcting that
Regulation
(Text with EEA relevance)
THE EUROPEAN COMMISSION,
Having regard to the Treaty on the Functioning of the European Union,
Having regard to Regulation (EU) No 528/2012 of the European Parliament and of the Council of 22 May 2012 concerning
the making available on the market and use of biocidal products(1), and in particular Article 50(2), thereof,
Whereas:
(1) On 22 July 2022, Commission Implementing Regulation (EU) 2022/1434(2)granted a Union authorisation, under
number EU-0025449-0000, to Nutrition & Biosciences Netherlands B.V. for the making available on the market and
use of the biocidal product family ‘CMIT-MIT Aqueous 1.5-15’.
(2) The company ‘Nutrition & Biosciences Netherlands B.V.’ was acquired by the company ‘MC (Netherlands) 1 B.V.’
before Implementing Regulation (EU) 2022/1434 was adopted, and that Implementing Regulation should therefore
have referred to ‘MC (Netherlands) 1 B.V’ in Article 1 thereof as being the authorisation holder, as was correctly done
in the summary of the biocidal product characteristics (‘SPC’) for the biocidal product family ‘CMIT-MIT Aqueous
1.5-15’in the Annex to that Implementing Regulation.
(3) On 5 June 2024 and 14 January 2025 ‘MC, (Netherlands) 1 B.V.’ submitted to the European Chemicals Agency (‘the
Agency’), in accordance with Article 11(1) of Commission Implementing Regulation (EU) No 354/2013(3),
notifications of administrative changes to the Union authorisation for the biocidal product family ‘CMIT-MIT
Aqueous 1.5-15’. Those notifications were recorded in the register for biocidal products under case numbers
BC-HX095612-07 and BC-HH102376-51. The notified proposed changes to that authorisation concern the
addition of a manufacturer of the active substance, changes in the names of the manufacturers of the biocidal
product, the addition of a manufacturer of the biocidal product, and changes to the address of the authorisation
holder.
(4) On 11 July 2024 and 18 February 2025, the Agency submitted to the Commission, in accordance with Article 11(3)
of Implementing Regulation (EU) No 354/2013, opinions(4) on the notified administrative changes to the Union
authorisation for the biocidal product family ‘CMIT-MIT Aqueous 1.5-15’. In the opinions, the Agency concludes
that the proposed changes are administrative changes as referred to in Article 50(3), point (a), of Regulation (EU)
No 528/2012 and as specified in Title 1, Section 1, and Title 1, Section 2, of the Annex to Implementing Regulation
(EU) No 354/2013, and that, after the implementation of the changes, the conditions of Article 19 of Regulation (EU)
No 528/2012 will still be met.
(1) OJ L 167, 27.6.2012, p. 1, ELI: http://data.europa.eu/eli/reg/2012/528/oj.
(2) Commission Implementing Regulation (EU) 2022/1434 of 22 July 2022 granting a Union authorisation for the biocidal product
family ‘CMIT-MIT Aqueous 1.5-15’ (OJ L 226, 31.8.2022, p. 1, ELI: http://data.europa.eu/eli/reg_impl/2022/1434/oj).
(3) Commission Implementing Regulation (EU) No 354/2013 of 18 April 2013 on changes of biocidal products authorised in accordance
with Regulation (EU) No 528/2012 of the European Parliament and of the Council (OJ L 109, 19.4.2013, p.4, ELI: http://data.europa.
eu/eli/reg_impl/2013/354/oj).
(4) ECHA opinions UAD-C-1750430-43-00/F of 11 July 2024 and UAD-C-1803043-39-00/F of 18 February 2025 on administrative
changes of the Union authorisation of the biocidal product family ‘CMIT-MIT Aqueous 1.5-15’, https://echa.europa.eu/opinions-on-
union-authorisation.
ELI: http://data.europa.eu/eli/reg_impl/2025/2202/oj 1/227EN
OJ L, 20.11.2025
(5) On 18 February 2025, the Agency transmitted to the Commission the revised SPCs of the Union authorisation for
the biocidal product family ‘CMIT-MIT Aqueous 1.5-15’ in all official languages of the Union, covering all
administrative changes applied for, in accordance with Article 11(6) of Implementing Regulation (EU) No 354/2013.
(6) The Commission concurs with the opinions of the Agency and therefore considers it appropriate to amend the Union
authorisation for the biocidal product family ‘CMIT-MIT Aqueous 1.5-15’ to introduce the administrative changes
requested by ‘MC (Netherlands) 1 B.V.’
(7) Apart from the amendments regarding the proposed changes, all other information included in the summary of the
biocidal product characteristics of ‘CMIT-MIT Aqueous 1.5-15’, as set out in the Annex to Implementing Regulation
(EU) 2022/1434, remain unchanged.
(8) In order to enhance clarity and to ease the access of users and interested parties to the consolidated version of the
summary of the biocidal product characteristics which is to be published by the Agency, the Annex to Implementing
Regulation (EU) 2022/1434 should be replaced in its entirety. Due to a change in the format used for the generation
of the summary of biocidal product characteristics in the register for biocidal products in February 2024, the
summary of biocidal product characteristics in that Annex should also include some minor editorial and layout
changes.
(9) Implementing Regulation (EU) No 2022/1434 should therefore be amended accordingly,
HAS ADOPTED THIS REGULATION:
Article 1
Article 1 of Implementing Regulation (EU) 2022/1434 is replaced by the following:
‘A Union authorisation with authorisation number EU-0025449-0000 is granted to MC (Netherlands) 1 B.V. for the
making available on the market and use of the biocidal product family “CMIT-MIT Aqueous 1.5-15” in accordance with
the summary of the biocidal product characteristics set out in the Annex.
The Union authorisation is valid from 20 September 2022 until 31 August 2032.’.
Article 2
The Annex to Implementing Regulation (EU) 2022/1434 is replaced by the text set out in the Annex to this Regulation.
Article 3
This Regulation shall enter into force on the twentieth day following that of its publication in the Official Journal of the
European Union.
This Regulation shall be binding in its entirety and directly applicable in all Member States.
Done at Brussels, 22 October 2025.
For the Commission
The President
Ursula VON DER LEYEN
2/227 ELI: http://data.europa.eu/eli/reg_impl/2025/2202/ojEN
OJ L, 20.11.2025
ANNEX
SUMMARY OF PRODUCT CHARACTERISTICS FOR A BIOCIDAL PRODUCT FAMILY
CMIT-MIT Aqueous 1.5-15
Product type(s)
PT02: Disinfectants and algaecides not intended for direct application to humans or animals
PT04: Food and feed area
PT06: Preservatives for products during storage
PT11: Preservatives for liquid-cooling and processing systems
PT12: Slimicides
PT13: Working or cutting fluid preservatives
Authorisation number: EU-0025449-0000
R4BP asset number: EU-0025449-0000
PART I.
FIRST INFORMATION LEVEL
1. ADMINISTRATIVE INFORMATION
1.1. Family name
Name CMIT-MIT Aqueous 1.5-15
1.2. Product type(s)
Product type(s) PT02: Disinfectants and algaecides not intended for direct
application to humans or animals
PT04: Food and feed area
PT06: Preservatives for products during storage
PT11: Preservatives for liquid-cooling and processing systems
PT12: Slimicides
PT13: Working or cutting fluid preservatives
1.3. Authorisation holder
Name MC (Netherlands) 1 B.V.
Name and address of the authorisation
holder
Address Montrealweg 15 3197KH Botlek Rotterdam NL
ELI: http://data.europa.eu/eli/reg_impl/2025/2202/oj 3/227EN
OJ L, 20.11.2025
Authorisation number EU-0025449-0000
R4BP asset number EU-0025449-0000
Date of the authorisation 20/09/2022
Expiry date of the authorisation 31/08/2032
1.4. Manufacturer(s) of the product
Name of manufacturer AD Productions BV
Address of manufacturer Markweg Zuid 27 4794 SN Heijningen, Netherlands (the)
Location of manufacturing sites AD Productions BV site 1 Markweg Zuid 27 4794 SN
Heijningen, Netherlands (the)
Name of manufacturer Jiangsu FOPIA Chemicals Co., Ltd
Address of manufacturer Touzeng Village 224555 Binhuai Town, Binhai County,
Yancheng City, Jiangsu, China
Location of manufacturing sites Jiangsu FOPIA Chemicals Co., Ltd site 1 Touzeng Village
224555 Binhuai Town, Binhai County, Yancheng City,
Jiangsu, China
Name of manufacturer Acquaflex S.R.L
Address of manufacturer Vigano di Gaggiano 20083 Milan, Italy
Location of manufacturing sites Acquaflex S.R.L site 1 Vigano di Gaggiano 20083 Milan, Italy
Name of manufacturer LABORATORIOS MIRET, S.A.
Address of manufacturer Hercules, 18 08228 Terrassa, Barcelona, Spain
Location of manufacturing sites LABORATORIOS MIRET, S.A. site 1 Hercules, 18 08228
Terrassa, Barcelona, Spain
Name of manufacturer HYDRACHIM
Address of manufacturer Route de Saint Poix 35370 LE PERTRE, France
Location of manufacturing sites HYDRACHIM site 1 Route de Saint Poix 35370 LE PERTRE,
France
Name of manufacturer DAXEL srl.
Address of manufacturer via Pietro Nenni 8 42048 Rubiera RE, Italy
Location of manufacturing sites DAXEL srl. site 1 via Pietro Nenni 8 42048 Rubiera RE, Italy
4/227 ELI: http://data.europa.eu/eli/reg_impl/2025/2202/ojEN
OJ L, 20.11.2025
Name of manufacturer Aquatreat Chemical Products Ltd
Address of manufacturer Unit 7, Abbey Industrial Estate, 24 Willow Lane CR4 4NA
Mitcham, United Kingdom of Great Britain and Northern
Ireland (the)
Location of manufacturing sites Aquatreat Chemical Products Ltd site 1 Unit 7, Abbey
Industrial Estate, 24 Willow Lane CR4 4NA Mitcham, United
Kingdom of Great Britain and Northern Ireland (the)
Name of manufacturer Flexfill s.r.o.
Address of manufacturer Siřejovická 1213 410 02 Lovosice, Czechia
Location of manufacturing sites Flexfill s.r.o. site 1 Siřejovická 1213 410 02 Lovosice, Czechia
Name of manufacturer Sopura SA
Address of manufacturer 199 rue de trazegnies 6180 Courcelles, Belgium
Location of manufacturing sites Sopura SA site 1 199 rue de trazegnies 6180 Courcelles,
Belgium
Name of manufacturer Stenco Industrial
Address of manufacturer C/ Gran Vial, 50817 Montornès del Vallès, Barcelona, Spain
Location of manufacturing sites Stenco Industrial site 1 C/ Gran Vial, 50817 Montornès del
Vallès, Barcelona, Spain
Name of manufacturer Veolia WTS France S.A.S.
Address of manufacturer 44, Rue Paul Sabatier Z.I. Nord 71530 Crissey, France
Location of manufacturing sites Veolia WTS France S.A.S. site 1 44, Rue Paul Sabatier Z.I.
Nord 71530 Crissey, France
Name of manufacturer QUIPROCALT S.L.
Address of manufacturer Calle Lleida, 2 (Pol Ind Empalme) 43712 Llorenç del Penedès.
Tarragona, Spain
Location of manufacturing sites QUIPROCALT S.L. site 1 Calle Lleida, 2 (Pol Ind Empalme)
43712 Llorenç del Penedès. Tarragona, Spain
Name of manufacturer nv Buckman Laboratories
Address of manufacturer Wondelgemkaai 159 9000 Gent, Belgium
Location of manufacturing sites nv Buckman Laboratories site 1 Wondelgemkaai 159 9000
Gent, Belgium
ELI: http://data.europa.eu/eli/reg_impl/2025/2202/oj 5/227EN
OJ L, 20.11.2025
Name of manufacturer N.C.R. Biochemical S.p.A.
Address of manufacturer Via dei Carpentieri n.8 40050 Castello d’Argile, Italy
Location of manufacturing sites N.C.R. Biochemical S.p.A. site 1 Via dei Carpentieri n.8
40050 Castello d’Argile, Italy
Name of manufacturer Alliance Production
Address of manufacturer 4 BOULEVARD DEODAT DE SEVERAC 31770 COLOMIERS,
France
Location of manufacturing sites Alliance Production site 1 4 BOULEVARD DEODAT DE
SEVERAC 31770 COLOMIERS, France
Name of manufacturer URQUIMIA S.L.
Address of manufacturer POL. IND. DE ARASO C/ERREGEOIANA 2G 20305 Irún,
Guipúzcoa, Spain
Location of manufacturing sites URQUIMIA S.L. site 1 POL. IND. DE ARASO
C/ERREGEOIANA 2G 20305 Irún, Guipúzcoa, Spain
Name of manufacturer Kalon Mantenimiento Industrial S.A.
Address of manufacturer Avenida de la Industria 4 28823 Coslada, Madrid, Spain
Location of manufacturing sites Kalon Mantenimiento Industrial S.A. site 1 Avenida de la
Industria 4 28823 Coslada, Madrid, Spain
Name of manufacturer Filtrotech Sarl
Address of manufacturer Route des Jeunes 5D 1227 Les Acacias / Genève, Switzerland
Location of manufacturing sites Filtrotech Sarl site 1 Route des Jeunes 5D 1227 Les Acacias /
Genève, Switzerland
Name of manufacturer Helamin France Sarl
Address of manufacturer Le Technoparc, 135 rue Thomas-Edison 01630 Saint Genis
Pouilly, France
Location of manufacturing sites Helamin France Sarl site 1 Le Technoparc, 135 rue Thomas-
Edison 01630 Saint Genis Pouilly, France
Name of manufacturer Odyssée Environnement
Address of manufacturer Z.A de la Belle Croix 72510 Requeil, France
Location of manufacturing sites Odyssée Environnement site 1 Z.A de la Belle Croix 72510
Requeil, France
6/227 ELI: http://data.europa.eu/eli/reg_impl/2025/2202/ojEN
OJ L, 20.11.2025
Name of manufacturer MSGA SERVIVAP
Address of manufacturer 50 Rue Jean Zay Bâtiment D1 69800 ST PRIEST, France
Location of manufacturing sites MSGA SERVIVAP site 1 50 Rue Jean Zay Bâtiment D1 69800
ST PRIEST, France
Name of manufacturer TECNA ACONDICIONAMIENTOS DE AGUA S.A
Address of manufacturer Letxumborro Hiribidea,52 20305 Irun, Guipúzcoa, Spain
Location of manufacturing sites TECNA ACONDICIONAMIENTOS DE AGUA S.A site 1
Letxumborro Hiribidea,52 20305 Irun, Guipúzcoa, Spain
Name of manufacturer h2o facilities sa
Address of manufacturer av. des Grandes-Communes 8 CH-1213 Petit-Lancy, France
Location of manufacturing sites h2o facilities sa site 1 av. des Grandes-Communes 8 CH-1213
Petit-Lancy, France
Name of manufacturer FUPINAX S.L.
Address of manufacturer Polígono Industrial El Saladar I, C/ Molina, Nave 4 30564
Lorquí, Spain
Location of manufacturing sites FUPINAX S.L. site 1 Polígono Industrial El Saladar I, C/
Molina, Nave 4 30564 Lorquí, Spain
Name of manufacturer Tresch/ chassieu
Address of manufacturer 3 Rue Blaise Pascal 69680 Chassieu, France
Location of manufacturing sites Tresch/ chassieu site 1 3 Rue Blaise Pascal 69680 Chassieu,
France
Name of manufacturer DUPUY
Address of manufacturer 42 Rue Saint Martin 08400 Quatre Champs, France
Location of manufacturing sites DUPUY site 1 42 Rue Saint Martin 08400 Quatre Champs,
France
Name of manufacturer Veolia Water Technologies & Solutions Belgium BVBA
Address of manufacturer Toekomstlaan 54, Industriepark Wolfstee 2200 HERENTALS,
Belgium
ELI: http://data.europa.eu/eli/reg_impl/2025/2202/oj 7/227EN
OJ L, 20.11.2025
Location of manufacturing sites Veolia Water Technologies & Solutions Belgium BVBA site 1
Toekomstlaan 54, Industriepark Wolfstee 2200 HERENTALS,
Belgium
Name of manufacturer Buckman Laboratories (Pty)Ltd
Address of manufacturer 1 Buckman Boulevard 3700 Hammarsdale, South Africa
Location of manufacturing sites Buckman Laboratories (Pty)Ltd site 1 1 Buckman Boulevard
3700 Hammarsdale, South Africa
Name of manufacturer EAUTEX
Address of manufacturer 28 RUE KELLERMANN 59100 ROUBAIX, France
Location of manufacturing sites EAUTEX site 1 28 RUE KELLERMANN 59100 ROUBAIX,
France
Name of manufacturer Hydrogel-Chemie Wasseraufbereitungs-Gesellschaft mbH
Address of manufacturer Zur Mersch 19 59457 Werl, Germany
Location of manufacturing sites Hydrogel-Chemie Wasseraufbereitungs-Gesellschaft mbH site
1 Zur Mersch 19 59457 Werl, Germany
Name of manufacturer sceo
Address of manufacturer ZA PECHNAUQUIE SUD 31340 VILLEMR SUR TARN,
France
Location of manufacturing sites sceo site 1 ZA PECHNAUQUIE SUD 31340 VILLEMR SUR
TARN, France
Name of manufacturer Nutrition & Biosciences (Switzerland) GmbH
Address of manufacturer Wolleraustrasse 15-17 CH-8807 Freienbach, Switzerland
Location of manufacturing sites Nutrition & Biosciences (Switzerland) GmbH site 1 Haven
1931 Geslecht 9130 Kallo, Belgium
Nutrition & Biosciences (Switzerland) GmbH site 2
Madoerastraat 10 3199 KR Maasvlakte Rotterdam,
Netherlands (the)
Name of manufacturer Theseo Deutschland GmbH
Address of manufacturer Kolpingstrasse 4 49835 Wietmarschen Germany
Location of manufacturing sites Theseo Deutschland GmbH site 1 Kolpingstrasse 4 49835
Wietmarschen Germany
8/227 ELI: http://data.europa.eu/eli/reg_impl/2025/2202/ojEN
OJ L, 20.11.2025
1.5. Manufacturer(s) of the active substance(s)
Active substance C(M)IT/MIT (3:1)
Name of manufacturer Jiangsu FOPIA Chemicals Co., Ltd
Address of manufacturer Touzeng Village 224555 Binhuai Town, Binhai County,
Yancheng City, Jiangsu, China
Location of manufacturing sites Jiangsu FOPIA Chemicals Co., Ltd site 1 Touzeng Village
224555 Binhuai Town, Binhai County, Yancheng City,
Jiangsu, China
Active substance C(M)IT/MIT (3:1)
Name of manufacturer Dalian Bio-chem Company Limited
Address of manufacturer No 18, Mubai Road, Songmudao Chemical Industry Park,
PuWan New District, Liaoning Province 116308 Dalian
China
Location of manufacturing sites Dalian Bio-chem Company Limited site 1 No 18, Mubai
Road, Songmudao Chemical Industry Park, PuWan New
District, Liaoning Province 116308 Dalian China
2. PRODUCT FAMILY COMPOSITION AND FORMULATION
2.1. Qualitative and quantitative information on the composition of the family
Common name IUPAC name Function CAS number EC number Content (%)
C(M)IT/MIT (3:1) Reaction mass Active 55965-84-9 2,2 - 20,9 % (w/
of 5-chloro- substance w)
2-methyl-2h-
isothiazol-
3-one
and 2-methyl-
2h-isothiazol-
3-one (3:1)
2.2. Type(s) of formulation
Formulation type(s) AL Any other liquid
PART II.
SECOND INFORMATION LEVEL META SPC(S)
1. META SPC 1 ADMINISTRATIVE INFORMATION
1.1. Meta SPC 1 identifier
Identifier Meta SPC: meta-SPC 1 KATHON 13-15 Mg
ELI: http://data.europa.eu/eli/reg_impl/2025/2202/oj 9/227EN
OJ L, 20.11.2025
1.2. Suffix to the authorisation number
Number 1-1
1.3. Product type(s)
Product type(s) PT02: Disinfectants and algaecides not intended for direct
application to humans or animals
PT04: Food and feed area
PT06: Preservatives for products during storage
PT11: Preservatives for liquid-cooling and processing systems
PT12: Slimicides
PT13: Working or cutting fluid preservatives
2. META SPC 1 COMPOSITION
2.1. Qualitative and quantitative information on the composition of the meta SPC 1
Common name IUPAC name Function CAS number EC number Content (%)
C(M)IT/MIT (3:1) Reaction mass Active 55965-84-9 18,8 - 20,9 %
of 5-chloro- substance (w/w)
2-methyl-2h-
isothiazol-
3-one
and 2-methyl-
2h-isothiazol-
3-one (3:1)
2.2. Type(s) of formulation of the meta SPC 1
Formulation type(s) AL Any other liquid
3. HAZARD AND PRECAUTIONARY STATEMENTS OF THE META SPC 1
Hazard statements H302+H332: Harmful if swallowed or if inhaled.
H311: Toxic in contact with skin.
H314: Causes severe skin burns and eye damage.
H317: May cause an allergic skin reaction.
H410: Very toxic to aquatic life with long lasting effects.
H290: May be corrosive to metals.
EUH071: Corrosive to the respiratory tract.
Precautionary statements P260: Do not breathe fume.
P264: Wash skin thoroughly after handling.
10/227 ELI: http://data.europa.eu/eli/reg_impl/2025/2202/ojEN
OJ L, 20.11.2025
P270: Do not eat, drink or smoke when using this product.
P271: Use only outdoors or in a well-ventilated area.
P272: Contaminated work clothing should not be allowed
out of the workplace.
P273: Avoid release to the environment.
P280: Wear protective gloves/ protective clothing/ eye
protection/ face protection/ hearing protection .
P330: Rinse mouth.
P302+P352: IF ON SKIN: Wash with plenty of water.
P362+P364: Take off contaminated clothing and wash it
before reuse.
P301+P312: IF SWALLOWED: Call a Poison Center or doctor if
you feel unwell.
P333+P313: If skin irritation or rash occurs: Get medical
advice.
P301+P330+P331: IF SWALLOWED: rinse mouth. Do NOT
induce vomiting.
P303+P361+P353: IF ON SKIN (or hair): Take off immediately
all contaminated clothing. Rinse skin with water [or shower].
P304+P340: IF INHALED: Remove person to fresh air and
keep comfortable for breathing.
P310: Immediately call a Poison Center / doctor .
P305+P351+P338: IF IN EYES: Rinse cautiously with water for
several minutes. Remove contact lenses, if present and easy to
do. Continue rinsing.
P391: Collect spillage.
P405: Store locked up.
P234: Keep only in original packaging.
P390: Absorb spillage to prevent material damage.
P406: Store in a corrosion-resistant container with a resistant
inner liner.
4. AUTHORISED USE(S) OF THE META SPC
4.1. Use description
Table 1
Preservation of sump water in air conditioning and air washer systems.
Product type PT02: Disinfectants and algaecides not intended for direct application
to humans or animals
Where relevant, an exact description of -
the authorised use
ELI: http://data.europa.eu/eli/reg_impl/2025/2202/oj 11/227EN
OJ L, 20.11.2025
Target organism(s) (including Scientific name: no data
development stage) Common name: Bacteria (including L. pneumophila)
Development stage: no data
Scientific name: no data
Common name: Yeasts
Development stage: no data
Scientific name: no data
Common name: fungi
Development stage: no data
Scientific name: no data
Common name: algae
Development stage: no data
Field(s) of use outdoor use
Preservation of sump water in air conditioning and air washer
systems.
Air conditioning systems and in air washer systems to preserve the
sump water. Air washer systems are used extensively in textile
factories and in the tobacco industry to scrub or clean the air and for
fine control of temperature and humidity.
Application method(s) Method: -
Detailed description:
Automatic and Manual Dosing The biocidal product is typically
added in a central chilled water sump which supplies several air
washers. The loading process may be conducted either manually or
by automation. In the automated process, the biocide is metered
directly into the sump from a holding tank or other type of bulk
container by a dosimeter (pump). The feeding pipe must dose the
biocidal product below the water level in order to limit its
evaporation.
Application rate(s) and frequency Application Rate:
Curative application: Bacteria, yeasts and fungi. When the system is
noticeably fouled, apply 5 to 14,9 mg C(M)IT/MIT (3:1) per Litre of
water to be treated, as post treatment after a shock dose of minimum
0,3 ppm of free chlorine. Preventive application: algae When control
is obtained, add a continuous or semi continuous feed of 3 to 5 mg
C(M)IT/MIT (3:1) per L of water to be treated
-
Number and timing of application:
Curative application: Bacteria, yeasts and fungi
When the system is noticeably fouled, apply 5 to 14,9 mg C(M)
IT/MIT (3:1) per Litre of water to be treated, as post treatment after a
shock dose of minimum 0,3 ppm of free chlorine.
Contact time of 1 hour.
Preventive application: algae
When control is obtained, add a continuous or semi continuous feed
of 3 to 5 mg C(M)IT/MIT (3:1) per L of water to be treated.
12/227 ELI: http://data.europa.eu/eli/reg_impl/2025/2202/ojEN
OJ L, 20.11.2025
Regardless of the manner of treatment, the total concentration of the
active ingredient C(M)IT/MIT (3:1) in the system should not exceed
14,9 mg/L in the sump water.
Preliminary steps prior to addition:
The biocidal product is automatically dosed to the system. Manual
handling is necessary for the loading of the biocidal product into the
dosing systems.
Application Frequency:
Nominally every 2 to 3 days or as needed to obtain control. Repeat
until fouling is reduced to an acceptable level for controlling the
microbial growth.
Category(ies) of users industrial
Pack sizes and packaging material For industrial and professional users:
— High Density Poly Ethylene (HDPE) flask: 5 L (nominal)
— HDPE Pail / Jerrycan: 10 L, 20 L, 25 L, 30 L (nominal)
— Box with HDPE liner: 20 L
— HDPE Drum: 110 L, 120 L, 200 L, 260 L
— HDPE Intermediate bulk container (IBC): 650 L, 800 L, 1 000 L,
1 250 L
All products should be transport and stored in a vented room.
4.1.1. Use-specific instructions for use
— Respect the conditions of use of the product (concentration, contact time, temperature, pH, etc.).
— The CMIT/MIT biocidal products are used after a shock dose of free chlorine in this application as standard
industry practice.
4.1.2. Use-specific risk mitigation measures
— Rinse the system (especially the dispensing pumps) with water prior to perform the cleaning step.
— During mixing and loading and cleaning of the dispensing pumps, exposure to the product (corrosive and
skin sensitizer product) has to be limited by use of personal protective equipment (PPE) and application of
technical and organisational risk mitigation measures (RMM):
— Minimisation of manual phases (process automation);
— Use of a dosing device;
— Regular cleaning of equipment and work area;
— Avoidance of contact with contaminated tools and objects;
— Good standard of general ventilation;
— Training and management of staff on good practice.
— PPE is as follows:
— protective chemical resistant gloves (glove material to be specified by the authorisation holder within
the product information);
ELI: http://data.europa.eu/eli/reg_impl/2025/2202/oj 13/227EN
OJ L, 20.11.2025
— protective coverall (at least type 3 or 4, EN 14605) which is impermeable for the biocidal product
shall be worn (coverall material to be specified by the authorisation holder within the product
information);
— Eye protection;
— Substance/task appropriate respirator if ventilation is inadequate.
4.1.3. Where specific to the use, the particulars of likely direct or indirect effects, first aid instructions and emergency measures to
protect the environment
See general directions for use.
4.1.4. Where specific to the use, the instructions for safe disposal of the product and its packaging
See general directions for use.
4.1.5. Where specific to the use, the conditions of storage and shelf-life of the product under normal conditions of storage
See general directions for use.
4.2. Use description
Table 2
Preservation of fluids in conveyor belts and pasteurisers
Product type PT04: Food and feed area
Where relevant, an exact description of -
the authorised use
Target organism(s) (including Scientific name: no data
development stage) Common name: Bacteria
Development stage: no data
Scientific name: no data
Common name: Yeasts
Development stage: no data
Scientific name: no data
Common name: fungi
Development stage: no data
Field(s) of use indoor use
Preservation of fluids in conveyor belts and pasteurisers
The biocidal product is used for the preservation of process fluids in
pasteurisers and conveyor belts used in food industry. The biocidal
product is used in these systems to either control or kill bacteria and
fungi.
Application method(s) Method: closed system
Detailed description:
Automated dosing The biocidal product is dosed automatically in the
heat transfer fluid, in a place of good mixing (e.g. collecting sump
below the conveyor belt).
14/227 ELI: http://data.europa.eu/eli/reg_impl/2025/2202/ojEN
OJ L, 20.11.2025
Application rate(s) and frequency Application Rate:
Curative application: Bacteria, yeasts and fungi When the system is
noticeably fouled, apply 10 to 14,9 g C(M)IT/MIT (3:1) per m3 of
water to be treated as post treatment after a shock dose of minimum
0,3 ppm of free chlorine Preventive application: Bacteria: When
control is obtained, add a continuous or semi continuous feed of 2,5
to 5 g C(M)IT/MIT (3:1) per m3 of water to be treated.
-
Number and timing of application:
Curative application: Bacteria, yeasts and fungi
When the system is noticeably fouled, apply 10 to 14,9 g C(M)IT/MIT
(3:1) per m3 of water to be treated as post treatment after a shock
dose of minimum 0,3 ppm of free chlorine.
Contact time of 1 hour.
Preventive application: Bacteria:
When control is obtained, add a continuous or semi continuous feed
of 2,5 to 5 g C(M)IT/MIT (3:1) per m3 of water to be treated.
Preliminary steps prior to addition:
The biocidal product is automatically dosed to system. Manual
handling is necessary for the loading of containers containing the
biocidal product into the dosing systems.
Application Frequency:
Nominally every 2 to 3 days or as needed to obtain control. Repeat
until fouling is reduced to an acceptable level for controlling the
microbial growth.
Category(ies) of users industrial
Pack sizes and packaging material For industrial and professional users:
— HDPE flask: 5 L (nominal)
— HDPE Pail / Jerrycan: 10 L, 20 L, 25 L, 30 L (nominal)
— Box with HDPE liner: 20 L
— HDPE Drum: 110 L, 120 L, 200 L, 260 L
— HDPE IBC: 650 L, 800 L, 1 000 L, 1 250 L
All products should be transport and stored in a vented room.
4.2.1. Use-specific instructions for use
— Respect the conditions of use of the product (concentration, contact time, temperature, pH, etc.).
— The CMIT/MIT biocidal products are used after a shock dose of free chlorine in this application as standard
industry practice.
4.2.2. Use-specific risk mitigation measures
— Rinse the system (especially the dispensing pumps) with water prior to perform the cleaning step.
— During mixing and loading and cleaning of the dispensing pumps, exposure to the product (corrosive and
skin sensitizer product) has to be limited by use of PPE and application of technical and organisational RMM:
— Minimisation of manual phases (process automation);
— Use of a dosing device;
ELI: http://data.europa.eu/eli/reg_impl/2025/2202/oj 15/227EN
OJ L, 20.11.2025
— Regular cleaning of equipment and work area;
— Avoidance of contact with contaminated tools and objects;
— Good standard of general ventilation;
— Training and management of staff on good practice.
— PPE is as follows:
— protective chemical resistant gloves (glove material to be specified by the authorisation holder within
the product information);
— protective coverall (at least type 3 or 4, EN 14605) which is impermeable for the biocidal product
shall be worn (coverall material to be specified by the authorisation holder within the product
information);
— Eye protection;
— Substance/task appropriate respirator if ventilation is inadequate.
4.2.3. Where specific to the use, the particulars of likely direct or indirect effects, first aid instructions and emergency measures to
protect the environment
See general directions for use.
4.2.4. Where specific to the use, the instructions for safe disposal of the product and its packaging
See general directions for use.
4.2.5. Where specific to the use, the conditions of storage and shelf-life of the product under normal conditions of storage
See general directions for use.
4.3. Use description
Table 3
Long term offline preservation of reverse osmosis membranes used in potable water
Product type PT04: Food and feed area
Where relevant, an exact description of -
the authorised use
Target organism(s) (including Scientific name: no data
development stage) Common name: Bacteria
Development stage: no data
Field(s) of use indoor use
Long term offline preservation of reverse osmosis membranes used
in potable water
The C(M)IT/MIT (3:1) biocidal product is recommended for
controlling biological growth in off-line trains reverse osmosis
membranes producing potable water for extended periods of time.
16/227 ELI: http://data.europa.eu/eli/reg_impl/2025/2202/ojEN
OJ L, 20.11.2025
Application method(s) Method: closed system
Detailed description:
Manual and automated dosing. It is recommended that fouled
membranes be cleaned prior to shut-down and preservation. Please
refer to RO /NF supplier manual for membrane cleaning and system
shutdown procedures. The biocidal product should be dispensed as a
tankside additive into the circulating use-dilution of the fluid, using a
metering pump or by manual pouring, at a point to assure adequate
mixing throughout the system. After complete filling of the trains
RO/NF systems with the biocide solution, pumps are stopped (Off
line treatment) for extended periods of time. Typically C(M)IT/MIT
(3:1) solutions are prepared in the CIP (cleaning in place) tank and
added via the dosing system. Dilution with the permeate water or
high quality water is recommended for the preparation of the biocide
solution. Membranes should be soaked in the biocide solution during
the shut-down period.
Application rate(s) and frequency Application Rate:
7,5 -20 g of C(M)IT/MIT (3:1)/ m3 of water
-
Number and timing of application:
7,5 -20 g of C(M)IT/MIT (3:1)/ m3 of water
Category(ies) of users industrial
Pack sizes and packaging material For industrial and professional users:
— HDPE flask: 5 L (nominal)
— HDPE Pail / Jerrycan: 10 L, 20 L, 25 L, 30 L (nominal)
— Box with HDPE liner: 20 L
— HDPE Drum: 110 L, 120 L, 200 L, 260 L
— HDPE IBC: 650 L, 800 L, 1 000 L, 1 250 L
All products should be transport and stored in a vented room.
4.3.1. Use-specific instructions for use
— Respect the conditions of use of the product (concentration, contact time, temperature, pH, etc.).
— Prior to taking the membranes back on-line, flush carefully the elements with permeate water in order to
eliminate all the residual biocidal product.
4.3.2. Use-specific risk mitigation measures
— Rinse the system (especially the dispensing pumps) with water prior to perform the cleaning step.
— During mixing and loading and cleaning of the whole system, exposure to the product (corrosive and skin
sensitizer product) has to be limited by use of PPE and application of technical and organisational RMM:
— Minimisation of manual phases (process automation);
— Use of a dosing device;
— Regular cleaning of equipment and work area;
— Avoidance of contact with contaminated tools and objects;
ELI: http://data.europa.eu/eli/reg_impl/2025/2202/oj 17/227EN
OJ L, 20.11.2025
— Good standard of general ventilation;
— Training and management of staff on good practice.
— PPE is as follows:
— protective chemical resistant gloves (glove material to be specified by the authorisation holder within
the product information);
— protective coverall (at least type 3 or 4, EN 14605) which is impermeable for the biocidal product
shall be worn (coverall material to be specified by the authorisation holder within the product
information);
— Eye protection;
— Substance/task appropriate respirator if ventilation is inadequate.
4.3.3. Where specific to the use, the particulars of likely direct or indirect effects, first aid instructions and emergency measures to
protect the environment
See general directions for use.
4.3.4. Where specific to the use, the instructions for safe disposal of the product and its packaging
See general directions for use.
4.3.5. Where specific to the use, the conditions of storage and shelf-life of the product under normal conditions of storage
See general directions for use.
4.4. Use description
Table 4
Preservation of paints and coatings
Product type PT06: Preservatives for products during storage
Where relevant, an exact description of -
the authorised use
Target organism(s) (including Scientific name: no data
development stage) Common name: Bacteria
Development stage: no data
Scientific name: no data
Common name: Yeasts
Development stage: no data
Field(s) of use indoor use
outdoor use
Preservation of paints and coatings (including electrodeposition)
The biocidal product is recommended to control the growth of
bacteria and yeasts in coatings applied by an electrodeposition
process and associated rinse systems and in water-based paints and
coatings in storage containers before use.
18/227 ELI: http://data.europa.eu/eli/reg_impl/2025/2202/ojEN
OJ L, 20.11.2025
Application method(s) Method: closed system
Detailed description:
Manual and automated dosing. The biocidal product should be
dispensed as a tankside additive into the fluid, using a metering pump
or by manual pouring, at a point to assure adequate mixing
throughout the system.
Application rate(s) and frequency Application Rate:
Industrial uses: 1,5 - 14,5 % C(M)IT/MIT in the biocidal products;
Professional paints and general public paints: 7,5-14,9 mg/kg C(M)
IT/MIT (3:1) in final product.
-
Number and timing of application:
The biocidal product is added at the time of manufacture, storage or
shipment.
Industrial uses:
1,5 - 14,5 % C(M)IT/MIT in the biocidal products.
Professional paints and general public paints:
7,5-14,9 mg/kg C(M)IT/MIT (3:1) in final product.
For the biocidal product as supplied: for industrial use only.
Category(ies) of users industrial
Pack sizes and packaging material For industrial and professional users:
— HDPE flask: 5 L (nominal)
— HDPE Pail / Jerrycan: 10 L, 20 L, 25 L, 30 L (nominal)
— Box with HDPE liner: 20 L
— HDPE Drum: 110 L, 120 L, 200 L, 260 L
— HDPE IBC: 650 L, 800 L, 1 000 L, 1 250 L
All products should be transport and stored in a vented room.
4.4.1. Use-specific instructions for use
— The preservative can be added at any stage of the production of the product.
— Earliest possible addition is recommended for optimal protection.
— Consult the manufacturer to determine the optimal dosage for the various products to be preserved.
— It is recommended that the optimum biocide concentration and compatibility with individual formulations
is determined by means of laboratory tests.
— The duration and storage conditions of the preserved matrices may impact the efficacy of the product,
microbiological tests should be conducted to determine the appropriate application rate without exceeding
the maximum authorised application rate.
— The biocidal product shall be used for treatment of products (articles/mixtures) distributed to professional
users and to the general public.
ELI: http://data.europa.eu/eli/reg_impl/2025/2202/oj 19/227EN
OJ L, 20.11.2025
4.4.2. Use-specific risk mitigation measures
— During handling phases of products from Meta SPC 1, 2, 3 and 4 (Mixing and Loading), exposure to the
product (corrosive and skin sensitizer products) has to be limited by use of PPE and application of technical
and organisational RMM:
— Minimisation of manual phases (process automation);
— Use of a dosing device;
— Regular cleaning of equipment and work area;
— Avoidance of contact with contaminated tools and objects;
— Good standard of general ventilation;
— Training and management of staff on good practice.
— PPE is as follows:
— protective chemical resistant gloves (glove material to be specified by the authorisation holder within
the product information);
— protective coverall (at least type 3 or 4, EN 14605) which is impermeable for the biocidal product
shall be worn (coverall material to be specified by the authorisation holder within the product
information);
— Eye protection;
— Substance/task appropriate respirator if ventilation is inadequate.
— The maximal concentration of products from Meta SPC 1, 2, 3 and 4 to be added in paints used must be
below the threshold value of 15 ppm.
4.4.3. Where specific to the use, the particulars of likely direct or indirect effects, first aid instructions and emergency measures to
protect the environment
See general directions for use.
4.4.4. Where specific to the use, the instructions for safe disposal of the product and its packaging
See general directions for use.
4.4.5. Where specific to the use, the conditions of storage and shelf-life of the product under normal conditions of storage
See general directions for use.
4.5. Use description
Table 5
Preservation of detergents and household products
Product type PT06: Preservatives for products during storage
Where relevant, an exact description of -
the authorised use
Target organism(s) (including Scientific name: no data
development stage) Common name: Bacteria
Development stage: no data
Scientific name: no data
Common name: Yeasts
Development stage: no data
20/227 ELI: http://data.europa.eu/eli/reg_impl/2025/2202/ojEN
OJ L, 20.11.2025
Scientific name: no data
Common name: fungi
Development stage: no data
Field(s) of use indoor use
Preservation of detergents (washing and cleaning fluids) and
household products.
The biocidal product is recommended for the control of bacteria,
yeast and fungi in detergents and cleaning fluids (i.e. hard surface
cleaners (all-purpose cleaners), hand dish washing products, fabric
softeners, laundry detergents), products used for car care, floor care,
waxes, hard surface cleaners, pre-moistened sponges or mops, and
the surfactants used in these types of products.
Application method(s) Method: closed system
Detailed description:
Manual and automated application. The biocidal product should be
dispensed to the end use fluid at a point to ensure adequate mixing
using preferably automated metering pump or by manual addition.
Application rate(s) and frequency Application Rate:
Industrial uses: 1,5 - 14,5 % C(M)IT/MIT in the biocidal products;
Professional and general public uses: 6-14,9 mg/kg C(M)IT/MIT (3:1)
in final product.
-
Number and timing of application:
The biocidal product is added at single dose at the time of
manufacturing, storage or shipment.
To ensure uniform distribution, slowly disperse using automated
metering or manual addition, into product with agitation. Mix
thoroughly until evenly dispersed throughout the product.
Institutional and Household products:
(detergents, cleaners, softeners, etc.)
Industrial uses:
1,5 - 14,5 % C(M)IT/MIT in the biocidal products.
Professional and general public uses:
6-14,9 mg/kg C(M)IT/MIT (3:1) in final product.
For the biocidal product as supplied: for industrial use only.
Category(ies) of users industrial
Pack sizes and packaging material For industrial and professional users:
— HDPE flask: 5 L (nominal)
— HDPE Pail / Jerrycan: 10 L, 20 L, 25 L, 30 L (nominal)
— Box with HDPE liner: 20 L
— HDPE Drum: 110 L, 120 L, 200 L, 260 L
— HDPE IBC: 650 L, 800 L, 1 000 L, 1 250 L
All products should be transport and stored in a vented room.
4.5.1. Use-specific instructions for use
— The preservative can be added at any stage of the production of the product.
— Earliest possible addition is recommended for optimal protection.
ELI: http://data.europa.eu/eli/reg_impl/2025/2202/oj 21/227EN
OJ L, 20.11.2025
— Consult the manufacturer to determine the optimal dosage for the various products to be preserved.
— It is recommended that the optimum biocide concentration and compatibility with individual formulations
is determined by means of laboratory tests.
— The duration and storage conditions of the preserved matrices may impact the efficacy of the product,
microbiological tests should be conducted to determine the appropriate application rate without exceeding
the maximum authorised application rate.
— The biocidal product shall be used for treatment of products (articles/mixtures) distributed to professional
users and to the general public.
4.5.2. Use-specific risk mitigation measures
— During handling phases of products from Meta SPC 1 and 3 (mixing and loading), exposure to the product
(corrosive and skin sensitizer products) has to be limited by use of PPE and application of technical and
organisational RMM:
— Minimisation of manual phases (process automation);
— Use of a dosing device;
— Regular cleaning of equipment and work area;
— Avoidance of contact with contaminated tools and objects;
— Good standard of general ventilation;
— Training and management of staff on good practice.
— PPE is as follows:
— protective chemical resistant gloves (glove material to be specified by the authorisation holder within
the product information);
— protective coverall (at least type 3 or 4, EN 14605) which is impermeable for the biocidal product
shall be worn (coverall material to be specified by the authorisation holder within the product
information);
— Eye protection;
— Substance/task appropriate respirator if ventilation is inadequate.
— The maximal concentration of products from Meta SPC 1 and 3 to be added in detergents and household
products used must be below the threshold value of 15 ppm.
4.5.3. Where specific to the use, the particulars of likely direct or indirect effects, first aid instructions and emergency measures to
protect the environment
See general directions for use.
4.5.4. Where specific to the use, the instructions for safe disposal of the product and its packaging
See general directions for use.
4.5.5. Where specific to the use, the conditions of storage and shelf-life of the product under normal conditions of storage
See general directions for use.
22/227 ELI: http://data.europa.eu/eli/reg_impl/2025/2202/ojEN
OJ L, 20.11.2025
4.6. Use description
Table 6
Preservation of fluids used in paper, textile and leather production - Curative treatment
Product type PT06: Preservatives for products during storage
Where relevant, an exact description of -
the authorised use
Target organism(s) (including Scientific name: no data
development stage) Common name: Bacteria
Development stage: no data
Field(s) of use indoor use
Preservation of fluids used in paper, textile and leather production -
The biocidal product is used to reduce contamination by bacteria in
textile additives (woven and non-woven, natural and synthetic
including silicone emulsions) processing chemicals, all chemicals used
in the leather process industry and paper additives (e.g. water
pigment pastes, starch, natural gums, synthetic and natural latexes,
sizing agents, coating binders, retention aids, dyes, fluorescent
whitening agents, wet-strength resins) used in paper mills. The
biocidal product inhibits the growth microorganisms, which would
otherwise lead to odours formation, viscosity alteration,
discolouration of product and premature product failure.
Application method(s) Method: closed system
Detailed description:
Manual and automated dosing. The biocidal product should be
dispensed to the end use fluid at a point to ensure adequate mixing
using preferably automated metering pump or by manual addition.
Application rate(s) and frequency Application Rate:
Industrial uses: 1,5 - 14,5 % C(M)IT/MIT in the biocidal products;
Professional uses: 16 to 30 mg/kg of C(M)IT/MIT (3:1) in final
product
-
Number and timing of application:
The biocidal product is added at single dose at time of manufacturing,
storage or shipment.
Industrial uses: 1,5 - 14,5 % C(M)IT/MIT in the biocidal products.
Professional uses:
Curative treatment:
16 to 30 mg/kg of C(M)IT/MIT (3:1) in final product
Contact time: 24 hours
For the biocidal product as supplied: for industrial use only.
Category(ies) of users industrial
Pack sizes and packaging material For industrial and professional users:
— HDPE flask: 5 L (nominal)
— HDPE Pail / Jerrycan: 10 L, 20 L, 25 L, 30 L (nominal)
ELI: http://data.europa.eu/eli/reg_impl/2025/2202/oj 23/227EN
OJ L, 20.11.2025
— Box with HDPE liner: 20 L
— HDPE Drum: 110 L, 120 L, 200 L, 260 L
— HDPE IBC: 650 L, 800 L, 1 000 L, 1 250 L
All products should be transport and stored in a vented room.
4.6.1. Use-specific instructions for use
— The preservative can be added at any stage of the production of the product.
— Earliest possible addition is recommended for optimal protection.
— Consult the manufacturer to determine the optimal dosage for the various products to be preserved.
— It is recommended that the optimum biocide concentration and compatibility with individual formulations
is determined by means of laboratory tests.
— The duration and storage conditions of the preserved matrices may impact the efficacy of the product,
microbiological tests should be conducted to determine the appropriate application rate without exceeding
the maximum authorised application rate.
— The biocidal product shall be used for treatment of products (articles/mixtures) distributed only to
professional users.
4.6.2. Use-specific risk mitigation measures
— During handling phases of products from Meta SPC 1, 2, 3 and 4 (mixing and loading), exposure to the
product (corrosive and skin sensitizer products) has to be limited by use of PPE and application of technical
and organisational RMM:
— Minimisation of manual phases (process automation);
— Use of a dosing device;
— Regular cleaning of equipment and work area;
— Avoidance of contact with contaminated tools and objects;
— Good standard of general ventilation;
— Training and management of staff on good practice.
— PPE is as follows:
— protective chemical resistant gloves (glove material to be specified by the authorisation holder within
the product information);
— protective coverall (at least type 3 or 4, EN 14605) which is impermeable for the biocidal product
shall be worn (coverall material to be specified by the authorisation holder within the product
information);
— Eye protection;
— Substance/task appropriate respirator if ventilation is inadequate.
— The maximal products concentration used for the preservation of fluids used in paper, textile and leather
production being above the threshold value of 15 ppm, exposure has to be limited by use of PPE protecting
skin and mucous membranes potentially exposed and application of technical and organisational RMM:
— Minimisation of manual phases;
— Use of a dosing device;
24/227 ELI: http://data.europa.eu/eli/reg_impl/2025/2202/ojEN
OJ L, 20.11.2025
— Regular cleaning of equipment and work area;
— Avoidance of contact with contaminated tools and objects;
— Good standard of general ventilation;
— Training and management of staff on good practice.
4.6.3. Where specific to the use, the particulars of likely direct or indirect effects, first aid instructions and emergency measures to
protect the environment
See general directions for use.
4.6.4. Where specific to the use, the instructions for safe disposal of the product and its packaging
See general directions for use.
4.6.5. Where specific to the use, the conditions of storage and shelf-life of the product under normal conditions of storage
See general directions for use.
4.7. Use description
Table 7
Preservation of glues and adhesives
Product type PT06: Preservatives for products during storage
Where relevant, an exact description of -
the authorised use
Target organism(s) (including Scientific name: no data
development stage) Common name: Bacteria
Development stage: no data
Scientific name: no data
Common name: Yeasts
Development stage: no data
Field(s) of use indoor use
Preservation of glues and adhesives
The biocidal product is recommended to control the growth of
bacteria and yeasts in water-soluble and water-dispersed synthetic and
natural adhesives and tackifiers in storage containers before use
Application method(s) Method: closed system
Detailed description:
Manual and automated application. The biocidal product should be
dispensed to the end use fluid at a point to ensure adequate mixing
using preferably automated metering pump or by manual addition.
Application rate(s) and frequency Application Rate:
Industrial uses: 1,5 - 14,5 % C(M)IT/MIT in the biocidal products;
Professional uses: 8-30 mg/kg C(M)IT/MIT (3:1) in final product.
General public uses: 8-14,9 mg/kg C(M)IT/MIT (3:1) in final product.
-
Number and timing of application:
The biocidal product is added at single dose at the time of
manufacture, storage or shipment.
ELI: http://data.europa.eu/eli/reg_impl/2025/2202/oj 25/227EN
OJ L, 20.11.2025
To ensure uniform distribution, slowly disperse using automated
metering or manual addition, into product with agitation. Mix
thoroughly until evenly dispersed throughout the product.
Industrial uses: 1,5 - 14,5 % C(M)IT/MIT in the biocidal products.
Professional uses:
8-30 mg/kg C(M)IT/MIT (3:1) in final product.
General public uses:
8-14,9 mg/kg C(M)IT/MIT (3:1) in final product.
For the biocidal product as supplied: for industrial use only.
Category(ies) of users industrial
Pack sizes and packaging material For industrial and professional users:
— HDPE flask: 5 L (nominal)
— HDPE Pail / Jerrycan: 10 L, 20 L, 25 L, 30 L (nominal)
— Box with HDPE liner: 20 L
— HDPE Drum: 110 L, 120 L, 200 L, 260 L
— HDPE IBC: 650 L, 800 L, 1 000 L, 1 250 L
All products should be transport and stored in a vented room.
4.7.1. Use-specific instructions for use
— The preservative can be added at any stage of the production of the product.
— Earliest possible addition is recommended for optimal protection.
— Consult the manufacturer to determine the optimal dosage for the various products to be preserved.
— It is recommended that the optimum biocide concentration and compatibility with individual formulations
is determined by means of laboratory tests.
— The duration and storage conditions of the preserved matrices may impact the efficacy of the product,
microbiological tests should be conducted to determine the appropriate application rate without exceeding
the maximum authorised application rate.
— The biocidal product shall be used for treatment of products (articles/mixtures) distributed to professional
users and to the general public. For products distributed to the general public the maximal concentration
used must be below the threshold value of 15 ppm.
4.7.2. Use-specific risk mitigation measures
— During handling phases of products from Meta SPC 1, 2, 3 and 4 (mixing and loading), exposure to the
product (corrosive and skin sensitizer products) has to be limited by use of PPE and application of technical
and organisational RMM:
— Minimisation of manual phases (process automation);
— Use of a dosing device;
— Regular cleaning of equipment and work area;
— Avoidance of contact with contaminated tools and objects;
— Good standard of general ventilation;
— Training and management of staff on good practice.
26/227 ELI: http://data.europa.eu/eli/reg_impl/2025/2202/ojEN
OJ L, 20.11.2025
— PPE is as follows:
— protective chemical resistant gloves (glove material to be specified by the authorisation holder within
the product information);
— protective coverall (at least type 3 or 4, EN 14605) which is impermeable for the biocidal product
shall be worn (coverall material to be specified by the authorisation holder within the product
information);
— Eye protection;
— Substance/task appropriate respirator if ventilation is inadequate.
— For professional users, the maximal products concentration used for the preservation of glues and adhesives
being above the threshold value of 15 ppm, exposure has to be limited by use of PPE, protecting skin and
mucous membranes potentially exposed, and application of technical and organisational RMM:
— Minimisation of manual phases;
— Use of a dosing device;
— Regular cleaning of equipment and work area;
— Good standard of general ventilation;
— Training and management of staff on good practice.
4.7.3. Where specific to the use, the particulars of likely direct or indirect effects, first aid instructions and emergency measures to
protect the environment
See general directions for use.
4.7.4. Where specific to the use, the instructions for safe disposal of the product and its packaging
See general directions for use.
4.7.5. Where specific to the use, the conditions of storage and shelf-life of the product under normal conditions of storage
See general directions for use.
4.8. Use description
Table 8
Preservation of polymer lattices
Product type PT06: Preservatives for products during storage
Where relevant, an exact description of -
the authorised use
Target organism(s) (including Scientific name: no data
development stage) Common name: Bacteria
Development stage: no data
Scientific name: no data
Common name: Yeasts
Development stage: no data
Scientific name: no data
Common name: fungi
Development stage: no data
ELI: http://data.europa.eu/eli/reg_impl/2025/2202/oj 27/227EN
OJ L, 20.11.2025
Field(s) of use indoor use
Preservation of polymer latexes
The biocidal product is recommended for the control of bacteria,
yeast and fungi in the manufacture, storage, and transport of latexes,
synthetic polymers including Hydrolysed Poly Acryl Amide (HPAM)
and biopolymers (e.g. xanthan, dextran..) natural latexes.
Application method(s) Method: closed system
Detailed description:
Manual and automated application. The biocidal product should be
dispensed to the end use fluid at a point to ensure adequate mixing
using preferably automated metering pump or by manual addition.
Application rate(s) and frequency Application Rate:
Industrial uses: 1,5 - 14,5 % C(M)IT/MIT in the biocidal products;
Professional uses: 14,9 - 50 mg /kg of C(M)IT/MIT (3:1) in final
product.
-
Number and timing of application:
The biocidal product is added at single dose at the time of
manufacture, storage or shipment.
To ensure uniform distribution, slowly disperse using automated
metering or manual addition, into product with agitation. Mix
thoroughly until evenly dispersed throughout the product.
Industrial uses: 1,5 - 14,5 % C(M)IT/MIT in the biocidal products.
Professional uses
14,9 - 50 mg /kg of C(M)IT/MIT (3:1) in final product.
For the biocidal product as supplied: for industrial use only.
Category(ies) of users industrial
Pack sizes and packaging material For industrial and professional users:
— HDPE flask: 5 L (nominal)
— HDPE Pail / Jerrycan: 10 L, 20 L, 25 L, 30 L (nominal)
— Box with HDPE liner: 20 L
— HDPE Drum: 110 L, 120 L, 200 L, 260 L
— HDPE IBC: 650 L, 800 L, 1 000 L, 1 250 L
All products should be transport and stored in a vented room.
4.8.1. Use-specific instructions for use
— The preservative can be added at any stage of the production of the product.
— Earliest possible addition is recommended for optimal protection.
— Consult the manufacturer to determine the optimal dosage for the various products to be preserved.
— It is recommended that the optimum biocide concentration and compatibility with individual formulations
is determined by means of laboratory tests.
28/227 ELI: http://data.europa.eu/eli/reg_impl/2025/2202/ojEN
OJ L, 20.11.2025
— The duration and storage conditions of the preserved matrices may impact the efficacy of the product,
microbiological tests should be conducted to determine the appropriate application rate without exceeding
the maximum authorised application rate.
— The biocidal product shall be used for treatment of products (articles/mixtures) distributed only to
professional users.
4.8.2. Use-specific risk mitigation measures
— During handling phases of products from Meta SPC 1, 2, 3 and 4 (mixing and loading), exposure to the
product (corrosive and skin sensitizer products) has to be limited by use of PPE and application of technical
and organisational RMM:
— Minimisation of manual phases (process automation);
— Use of a dosing device;
— Regular cleaning of equipment and work area;
— Avoidance of contact with contaminated tools and objects;
— Good standard of general ventilation;
— Training and management of staff on good practice.
— PPE is as follows:
— protective chemical resistant gloves (glove material to be specified by the authorisation holder within
the product information);
— protective coverall (at least type 3 or 4, EN 14605) which is impermeable for the biocidal product
shall be worn (coverall material to be specified by the authorisation holder within the product
information);
— Eye protection;
— Substance/task appropriate respirator if ventilation is inadequate.
— The maximal products concentration used for the preservation of polymer lattices being above the threshold
value of 15 ppm, exposure has to be limited by use of PPE, protecting skin and mucous membranes
potentially exposed, and application of technical and organisational RMM:
— Minimisation of manual phases;
— Use of a dosing device;
— Regular cleaning of equipment and work area;
— Good standard of general ventilation;
— Training and management of staff on good practice.
4.8.3. Where specific to the use, the particulars of likely direct or indirect effects, first aid instructions and emergency measures to
protect the environment
See general directions for use.
4.8.4. Where specific to the use, the instructions for safe disposal of the product and its packaging
See general directions for use.
4.8.5. Where specific to the use, the conditions of storage and shelf-life of the product under normal conditions of storage
See general directions for use.
ELI: http://data.europa.eu/eli/reg_impl/2025/2202/oj 29/227EN
OJ L, 20.11.2025
4.9. Use description
Table 9
Preservation of biocides and fertilizers
Product type PT06: Preservatives for products during storage
Where relevant, an exact description of -
the authorised use
Target organism(s) (including Scientific name: no data
development stage) Common name: Bacteria
Development stage: no data
Scientific name: no data
Common name: Yeasts
Development stage: no data
Field(s) of use indoor use
outdoor use
Preservation of biocides and fertilizers
The biocidal product is recommended to control the growth of
bacteria and yeasts in fertilizers and biocidal products.
Application method(s) Method: -
Detailed description:
Manual and automated application. The biocidal product should be
dispensed to the end use fluid at a point to ensure adequate mixing
using preferably automated metering pump or by manual addition.
Application rate(s) and frequency Application Rate:
Industrial uses: 1,5 - 14,5 % C(M)IT/MIT in the biocidal products;
Professional uses: 10- 30 mg/kg of C(M)IT/MIT (3:1) in final product.
-
Number and timing of application:
The biocidal product is added at single dose at the time of
manufacture, storage or shipment.
Industrial uses: 1,5 - 14,5 % C(M)IT/MIT in the biocidal products.
Professional uses:
10- 30 mg/kg of C(M)IT/MIT (3:1) in final product.
For the biocidal product as supplied: for industrial use only.
Category(ies) of users industrial
Pack sizes and packaging material For industrial and professional users:
— HDPE flask: 5 L (nominal)
— HDPE Pail / Jerrycan: 10 L, 20 L, 25 L, 30 L (nominal)
— Box with HDPE liner: 20 L
— HDPE Drum: 110 L, 120 L, 200 L, 260 L
— HDPE IBC: 650 L, 800 L, 1 000 L, 1 250 L
All products should be transport and stored in a vented room.
30/227 ELI: http://data.europa.eu/eli/reg_impl/2025/2202/ojEN
OJ L, 20.11.2025
4.9.1. Use-specific instructions for use
— The preservative can be added at any stage of the production of the product.
— Earliest possible addition is recommended for optimal protection.
— Consult the manufacturer to determine the optimal dosage for the various products to be preserved.
— It is recommended that the optimum biocide concentration and compatibility with individual formulations
is determined by means of laboratory tests.
— The duration and storage conditions of the preserved matrices may impact the efficacy of the product,
microbiological tests should be conducted to determine the appropriate application rate without exceeding
the maximum authorised application rate.
— The biocidal product shall be used for treatment of products (articles/mixtures) distributed only to
professional users.
4.9.2. Use-specific risk mitigation measures
— During handling phases of products from Meta SPC 1 and 3 (mixing and loading), exposure to the product
(corrosive and skin sensitizer products) has to be limited by use of PPE and application of technical and
organisational RMM:
— Minimisation of manual phases (process automation);
— Use of a dosing device;
— Regular cleaning of equipment and work area;
— Avoidance of contact with contaminated tools and objects;
— Good standard of general ventilation;
— Training and management of staff on good practice.
— PPE is as follows:
— protective chemical resistant gloves (glove material to be specified by the authorisation holder within
the product information);
— protective coverall (at least type 3 or 4, EN 14605) which is impermeable for the biocidal product
shall be worn (coverall material to be specified by the authorisation holder within the product
information);
— Eye protection;
— Substance/task appropriate respirator if ventilation is inadequate.
— For professional users, the maximal products concentration used for the preservation of biocides and
fertilizers being above the threshold value of 15 ppm, exposure has to be limited by use of PPE, protecting
skin and mucous membranes potentially exposed, and application of technical and organisational RMM:
— Minimisation of manual phases;
— Use of a dosing device;
— Regular cleaning of equipment and work area;
— Good standard of general ventilation;
— Training and management of staff on good practice.
ELI: http://data.europa.eu/eli/reg_impl/2025/2202/oj 31/227EN
OJ L, 20.11.2025
4.9.3. Where specific to the use, the particulars of likely direct or indirect effects, first aid instructions and emergency measures to
protect the environment
See general directions for use.
4.9.4. Where specific to the use, the instructions for safe disposal of the product and its packaging
See general directions for use.
4.9.5. Where specific to the use, the conditions of storage and shelf-life of the product under normal conditions of storage
See general directions for use.
4.10. Use description
Table 10
Preservation of mineral slurries
Product type PT06: Preservatives for products during storage
Where relevant, an exact description of -
the authorised use
Target organism(s) (including Scientific name: no data
development stage) Common name: Bacteria
Development stage: no data
Field(s) of use indoor use
Preservation of mineral slurries
The biocidal product is recommended to control the growth of
bacteria in aqueous-based inorganic/mineral slurries and inorganic
pigments which are formulated into paints, coatings and paper.
Application method(s) Method: closed system
Detailed description:
Manual and automated application. The biocidal product should be
dispensed as a tankside additive into the circulating use-dilution of
the fluid, using a metering pump or by manual pouring, at a point to
assure adequate mixing throughout the system.
Application rate(s) and frequency Application Rate:
Industrial uses: 1,5 - 14,5 % C(M)IT/MIT in the biocidal products;
Professional uses: 10- 30 mg/kg of C(M)IT/MIT (3:1) in final product.
-
Number and timing of application:
The biocidal product is added at single dose at the time of
manufacture, storage or shipment.
Industrial uses: 1,5 - 14,5 % C(M)IT/MIT in the biocidal products.
Professional uses:
10- 30 mg/kg of C(M)IT/MIT (3:1) in final product.
For the biocidal product as supplied: for industrial use only.
Category(ies) of users industrial
32/227 ELI: http://data.europa.eu/eli/reg_impl/2025/2202/ojEN
OJ L, 20.11.2025
Pack sizes and packaging material For industrial and professional users:
— HDPE flask: 5 L (nominal)
— HDPE Pail / Jerrycan: 10 L, 20 L, 25 L, 30 L (nominal)
— Box with HDPE liner: 20 L
— HDPE Drum: 110 L, 120 L, 200 L, 260 L
— HDPE IBC: 650 L, 800 L, 1 000 L, 1 250 L
All products should be transport and stored in a vented room.
4.10.1. Use-specific instructions for use
— The preservative can be added at any stage of the production of the product.
— Earliest possible addition is recommended for optimal protection.
— Consult the manufacturer to determine the optimal dosage for the various products to be preserved.
— It is recommended that the optimum biocide concentration and compatibility with individual formulations
is determined by means of laboratory tests.
— The duration and storage conditions of the preserved matrices may impact the efficacy of the product,
microbiological tests should be conducted to determine the appropriate application rate without exceeding
the maximum authorised application rate.
— The biocidal product shall be used for treatment of products (articles/mixtures) distributed only to
professional users.
4.10.2. Use-specific risk mitigation measures
— During handling phases of products from Meta SPC 1, 2, 3 and 4 (mixing and loading), exposure to the
product (corrosive and skin sensitizer products) has to be limited by use of PPE and application of technical
and organisational RMM:
— Minimisation of manual phases (process automation);
— Use of a dosing device;
— Regular cleaning of equipment and work area;
— Avoidance of contact with contaminated tools and objects;
— Good standard of general ventilation;
— Training and management of staff on good practice.
— PPE is as follows:
— protective chemical resistant gloves (glove material to be specified by the authorisation holder within
the product information);
— protective coverall (at least type 3 or 4, EN 14605) which is impermeable for the biocidal product
shall be worn (coverall material to be specified by the authorisation holder within the product
information);
— Eye protection;
— Substance/task appropriate respirator if ventilation is inadequate.
ELI: http://data.europa.eu/eli/reg_impl/2025/2202/oj 33/227EN
OJ L, 20.11.2025
The maximal products concentration used for the preservation of mineral slurries being above the threshold value
of 15 ppm, exposure has to be limited by use of PPE, protecting skin and mucous membranes potentially exposed,
and application of technical and organisational RMM:
— Minimisation of manual phases;
— Use of a dosing device;
— Regular cleaning of equipment and work area;
— Good standard of general ventilation;
— Training and management of staff on good practice.
4.10.3. Where specific to the use, the particulars of likely direct or indirect effects, first aid instructions and emergency measures to
protect the environment
See general directions for use.
4.10.4. Where specific to the use, the instructions for safe disposal of the product and its packaging
See general directions for use.
4.10.5. Where specific to the use, the conditions of storage and shelf-life of the product under normal conditions of storage
See general directions for use.
4.11. Use description
Table 11
Preservation of building products applied indoor only
Product type PT06: Preservatives for products during storage
Where relevant, an exact description of -
the authorised use
Target organism(s) (including Scientific name: no data
development stage) Common name: Bacteria
Development stage: no data
Scientific name: no data
Common name: Yeasts
Development stage: no data
Field(s) of use indoor use
Preservation of building (construction) products (including sealants,
caulks, plasters etc.)
The biocidal product is recommended to control the growth of
bacteria in building (construction) products (sealants, caulks,
biopolymers, plasters, fillers, admixtures concrete additives, joints
compounds,..).
Application method(s) Method: -
Detailed description:
Manual and automated dosing. The biocidal product should be
dispensed to the end use fluid at a point to ensure adequate mixing
using preferably automated metering pump or by manual addition.
34/227 ELI: http://data.europa.eu/eli/reg_impl/2025/2202/ojEN
OJ L, 20.11.2025
Application rate(s) and frequency Application Rate:
Industrial uses: 1,5 - 14,5 % C(M)IT/MIT in the biocidal products;
Professional uses: Add at typical use rate between 16,2-30 mg C(M)
IT/MIT (3:1) per Kg final product to be treated.
-
Number and timing of application:
The biocidal product is added at single dose at the time of
manufacture, storage or shipment.
Slowly dispense using automated metering or manually. Mix
thoroughly until the biocidal product is evenly dispersed.
Industrial uses:
1,5 - 14,5 % C(M)IT/MIT in the biocidal products.
Professional uses:
Add at typical use rate between 16,2-30 mg C(M)IT/MIT (3:1) per Kg
final product to be treated.
For the biocidal product as supplied: for industrial use only.
Category(ies) of users industrial
Pack sizes and packaging material For industrial and professional users:
— HDPE flask: 5 L (nominal)
— HDPE Pail / Jerrycan: 10 L, 20 L, 25 L, 30 L (nominal)
— Box with HDPE liner: 20 L
— HDPE Drum: 110 L, 120 L, 200 L, 260 L
— HDPE IBC: 650 L, 800 L, 1 000 L, 1 250 L
All products should be transport and stored in a vented room.
4.11.1. Use-specific instructions for use
— The preservative can be added at any stage of the production of the product.
— Earliest possible addition is recommended for optimal protection.
— Consult the manufacturer to determine the optimal dosage for the various products to be preserved.
— It is recommended that the optimum biocide concentration and compatibility with individual formulations
is determined by means of laboratory tests.
— The duration and storage conditions of the preserved matrices may impact the efficacy of the product,
microbiological tests should be conducted to determine the appropriate application rate without exceeding
the maximum authorised application rate.
— The biocidal product shall be used for treatment of products (articles/mixtures) distributed only to
professional users.
4.11.2. Use-specific risk mitigation measures
— This use is restricted to the preservation of building material applied indoor only.
— During handling phases for products from Meta SPC 1, 3 and 4 (mixing and loading), exposure to the
product (corrosive and skin sensitizer products) has to be limited by use of PPE and application of technical
and organisational RMM:
— Minimisation of manual phases (process automation);
ELI: http://data.europa.eu/eli/reg_impl/2025/2202/oj 35/227EN
OJ L, 20.11.2025
— Use of a dosing device;
— Regular cleaning of equipment and work area;
— Avoidance of contact with contaminated tools and objects;
— Good standard of general ventilation;
— Training and management of staff on good practice.
— PPE is as follows:
— protective chemical resistant gloves (glove material to be specified by the authorisation holder within
the product information);
— protective coverall (at least type 3 or 4, EN 14605) which is impermeable for the biocidal product
shall be worn (coverall material to be specified by the authorisation holder within the product
information);
— Eye protection;
— Substance/task appropriate respirator if ventilation is inadequate.
For professional users, the maximal products concentration used for the preservation of building products being
above the threshold value of 15 ppm, exposure has to be limited by use of PPE, protecting skin and mucous
membranes potentially exposed, and application of technical and organisational RMM:
— Minimisation of manual phases;
— Regular cleaning of equipment and work area;
— Good standard of general ventilation;
— Training and management of staff on good practice.
4.11.3. Where specific to the use, the particulars of likely direct or indirect effects, first aid instructions and emergency measures to
protect the environment
See general directions for use.
4.11.4. Where specific to the use, the instructions for safe disposal of the product and its packaging
See general directions for use.
4.11.5. Where specific to the use, the conditions of storage and shelf-life of the product under normal conditions of storage
See general directions for use.
4.12. Use description
Table 12
Preservation of electronic chemicals – Curative treatment
Product type PT06: Preservatives for products during storage
Where relevant, an exact description of -
the authorised use
Target organism(s) (including Scientific name: no data
development stage) Common name: Bacteria
Development stage: no data
Scientific name: no data
Common name: Yeasts
Development stage: no data
36/227 ELI: http://data.europa.eu/eli/reg_impl/2025/2202/ojEN
OJ L, 20.11.2025
Scientific name: no data
Common name: fungi
Development stage: no data
Field(s) of use indoor use
Preservation of electronic chemicals
The biocidal product is used to reduce contamination by bacteria,
yeasts and fungi in electronic chemicals as Chemical Mechanical
Polishing (CMP) silica slurries.
Application method(s) Method: closed system
Detailed description:
Manual and automated application. The biocidal product should be
dispensed to the end use fluid at a point to ensure adequate mixing
using preferably automated metering pump or by manual addition.
Application rate(s) and frequency Application Rate:
Industrial uses: 1,5 - 14,5 % C(M)IT/MIT in the biocidal products;
Professional uses: Add at typical use rate between 10-30 mg C(M)
IT/MIT (3:1) per L final product to be treated.
-
Number and timing of application:
The biocidal product is added at single dose at the time of
manufacture, storage or shipment.
Slowly dispense using automated metering or manually. Mix
thoroughly until the biocidal product is evenly dispersed.
Industrial uses: 1,5 - 14,5 % C(M)IT/MIT in the biocidal products.
Professional uses
Curative treatment:
10-30 mg C(M)IT/MIT (3:1) per kg final product to be treated.
Contact time: 7 days
For the biocidal product as supplied: for industrial use only.
Category(ies) of users industrial
Pack sizes and packaging material For industrial and professional users:
— HDPE flask: 5 L (nominal)
— HDPE Pail / Jerrycan: 10 L, 20 L, 25 L, 30 L (nominal)
— Box with HDPE liner: 20 L
— HDPE Drum: 110 L, 120 L, 200 L, 260 L
— HDPE IBC: 650 L, 800 L, 1 000 L, 1 250 L
All products should be transport and stored in a vented room.
4.12.1. Use-specific instructions for use
— The preservative can be added at any stage of the production of the product.
— Earliest possible addition is recommended for optimal protection.
— Consult the manufacturer to determine the optimal dosage for the various products to be preserved.
ELI: http://data.europa.eu/eli/reg_impl/2025/2202/oj 37/227EN
OJ L, 20.11.2025
— It is recommended that the optimum biocide concentration and compatibility with individual formulations
is determined by means of laboratory tests.
— The duration and storage conditions of the preserved matrices may impact the efficacy of the product,
microbiological tests should be conducted to determine the appropriate application rate without exceeding
the maximum authorised application rate.
— The biocidal product shall be used for treatment of products (articles/mixtures) distributed only to
professional users.
4.12.2. Use-specific risk mitigation measures
— During handling phases for products from Meta SPC 3 (mixing and loading), exposure to the product
(corrosive and skin sensitizer products) has to be limited by use of PPE and application of technical and
organisational RMM:
— Minimisation of manual phases (process automation);
— Use of a dosing device;
— Regular cleaning of equipment and work area;
— Avoidance of contact with contaminated tools and objects;
— Good standard of general ventilation;
— Training and management of staff on good practice.
— PPE is as follows:
— protective chemical resistant gloves (glove material to be specified by the authorisation holder within
the product information);
— protective coverall (at least type 3 or 4, EN 14605) which is impermeable for the biocidal product
shall be worn (coverall material to be specified by the authorisation holder within the product
information);
— Eye protection;
— Substance/task appropriate respirator if ventilation is inadequate.
— The maximal products concentration used for the preservation of electronic chemicals being above the
threshold value of 15 ppm, exposure has to be limited by use of PPE, protecting skin and mucous
membranes potentially exposed, and application of technical and organisational RMM:
— Minimisation of manual phases;
— Use of a dosing device;
— Regular cleaning of equipment and work area;
— Good standard of general ventilation;
— Training and management of staff on good practice.
4.12.3. Where specific to the use, the particulars of likely direct or indirect effects, first aid instructions and emergency measures to
protect the environment
See general directions for use.
4.12.4. Where specific to the use, the instructions for safe disposal of the product and its packaging
See general directions for use.
38/227 ELI: http://data.europa.eu/eli/reg_impl/2025/2202/ojEN
OJ L, 20.11.2025
4.12.5. Where specific to the use, the conditions of storage and shelf-life of the product under normal conditions of storage
See general directions for use.
4.13. Use description
Table 13
Preservation of inks
Product type PT06: Preservatives for products during storage
Where relevant, an exact description of -
the authorised use
Target organism(s) (including Scientific name: no data
development stage) Common name: Bacteria
Development stage: no data
Scientific name: no data
Common name: Yeasts
Development stage: no data
Field(s) of use indoor use
Preservation of inks
The biocidal product is recommended to control the growth of
bacteria and yeasts in inks and ink components (printing inks
lithographic, photographic, ink-jet fluids, water based dampening or
fountain solutions inks used for textile printing). The biocidal product
inhibits the growth of microorganisms, which would otherwise lead
to odour formation, viscosity alteration, product discolouration and
premature product failure.
Application method(s) Method: closed system
Detailed description:
Manual and automated dosing. The biocidal product should be
dispensed to the end use fluid at a point to ensure adequate mixing
using preferably automated metering pump or by manual addition.
Application rate(s) and frequency Application Rate:
Industrial uses: 1,5 - 14,5 % C(M)IT/MIT in the biocidal products.
Professional uses: 6-30 mg C(M)IT/MIT (3:1) /kg final product.
General public uses: 6-14,9 mg C(M)IT/MIT (3:1) /kg final product.
-
Number and timing of application:
The biocidal product is added at single dose at time of manufacturing,
storage or shipment.
Industrial uses: 1,5 - 14,5 % C(M)IT/MIT in the biocidal products.
Professional uses:
6-30 mg C(M)IT/MIT (3:1) /kg final product.
General public uses:
6-14,9 mg C(M)IT/MIT (3:1) /kg final product.
For the biocidal product as supplied: for industrial use only.
Category(ies) of users industrial
ELI: http://data.europa.eu/eli/reg_impl/2025/2202/oj 39/227EN
OJ L, 20.11.2025
Pack sizes and packaging material For industrial and professional users:
— HDPE flask: 5 L (nominal)
— HDPE Pail / Jerrycan: 10 L, 20 L, 25 L, 30 L (nominal)
— Box with HDPE liner: 20 L
— HDPE Drum: 110 L, 120 L, 200 L, 260 L
— HDPE IBC: 650 L, 800 L, 1 000 L, 1 250 L
All products should be transport and stored in a vented room.
4.13.1. Use-specific instructions for use
— The preservative can be added at any stage of the production of the product.
— Earliest possible addition is recommended for optimal protection.
— Consult the manufacturer to determine the optimal dosage for the various products to be preserved.
— It is recommended that the optimum biocide concentration and compatibility with individual formulations
is determined by means of laboratory tests.
— The duration and storage conditions of the preserved matrices may impact the efficacy of the product,
microbiological tests should be conducted to determine the appropriate application rate without exceeding
the maximum authorised application rate.
— The biocidal product shall be used for treatment of products (articles/mixtures) distributed to professional
users and to the general public. For products distributed to the general public the maximal concentration
used must be below the threshold value of 15 ppm.
4.13.2. Use-specific risk mitigation measures
— During handling phases of products from Meta SPC 1, 2, 3 and 4 (mixing and loading), exposure to the
product (corrosive and skin sensitizer products) has to be limited by use of PPE and application of technical
and organisational RMM:
— Minimisation of manual phases (process automation);
— Use of a dosing device;
— Regular cleaning of equipment and work area;
— Avoidance of contact with contaminated tools and objects;
— Good standard of general ventilation;
— Training and management of staff on good practice.
— PPE is as follows:
— protective chemical resistant gloves (glove material to be specified by the authorisation holder within
the product information);
— protective coverall (at least type 3 or 4, EN 14605) which is impermeable for the biocidal product
shall be worn (coverall material to be specified by the authorisation holder within the product
information);
— Eye protection;
— Substance/task appropriate respirator if ventilation is inadequate.
40/227 ELI: http://data.europa.eu/eli/reg_impl/2025/2202/ojEN
OJ L, 20.11.2025
— For professional users, the maximal products concentration used for the preservation of inks being above
the threshold value of 15 ppm, exposure has to be limited by use of PPE, protecting skin and mucous
membranes potentially exposed, and application of technical and organisational RMM:
— Minimisation of manual phases;
— Use of a dosing device;
— Regular cleaning of equipment and work area;
— Good standard of general ventilation;
— Training and management of staff on good practice.
4.13.3. Where specific to the use, the particulars of likely direct or indirect effects, first aid instructions and emergency measures to
protect the environment
See general directions for use.
4.13.4. Where specific to the use, the instructions for safe disposal of the product and its packaging
See general directions for use.
4.13.5. Where specific to the use, the conditions of storage and shelf-life of the product under normal conditions of storage
See general directions for use.
4.14. Use description
Table 14
Preservation of functional fluids (hydraulic fluids, antifreeze, corrosion inhibitors, etc. - excluding fuel
additives)
Product type PT06: Preservatives for products during storage
Where relevant, an exact description of -
the authorised use
Target organism(s) (including Scientific name: no data
development stage) Common name: Bacteria
Development stage: no data
Field(s) of use indoor use
Preservation of functional fluids (hydraulic fluids, antifreeze,
corrosion inhibitors, etc. - excluding fuel additives)
The biocidal product is recommended to control the growth of
bacteria in functional fluids such as brake and hydraulic fluids,
antifreeze additives, corrosion inhibitors, spinning fluids. The
biocidal product inhibits the growth microorganisms, which would
otherwise lead to odours formation, viscosity alteration,
discolouration of product and premature product failure.
Application method(s) Method: closed system
Detailed description:
Manual and automated dosing. The biocidal product should be
dispensed to the end use fluid at a point to ensure adequate mixing
using preferably automated metering pump or by manual addition.
ELI: http://data.europa.eu/eli/reg_impl/2025/2202/oj 41/227EN
OJ L, 20.11.2025
Application rate(s) and frequency Application Rate:
Industrial uses: 1,5 - 14,5 % C(M)IT/MIT in the biocidal products.
Professional uses: Add at a typical use rate between 6 to 30 mg C(M)
IT/MIT (3:1) per kg final product to be treated.
-
Number and timing of application:
The biocidal product is added at single dose at time of manufacturing,
storage or shipment.
Industrial uses: 1,5 - 14,5 % C(M)IT/MIT in the biocidal products.
Professional uses:
Add at a typical use rate between 6 to 30 mg C(M)IT/MIT (3:1) per kg
final product to be treated
For the biocidal product as supplied: for industrial use only.
Category(ies) of users industrial
Pack sizes and packaging material For industrial and professional users:
— HDPE flask: 5 L (nominal)
— HDPE Pail / Jerrycan: 10 L, 20 L, 25 L, 30 L (nominal)
— Box with HDPE liner: 20 L
— HDPE Drum: 110 L, 120 L, 200 L, 260 L
— HDPE IBC: 650 L, 800 L, 1 000 L, 1 250 L
All products should be transport and stored in a vented room.
4.14.1. Use-specific instructions for use
— The preservative can be added at any stage of the production of the product.
— Earliest possible addition is recommended for optimal protection.
— Consult the manufacturer to determine the optimal dosage for the various products to be preserved.
— It is recommended that the optimum biocide concentration and compatibility with individual formulations
is determined by means of laboratory tests.
— The duration and storage conditions of the preserved matrices may impact the efficacy of the product,
microbiological tests should be conducted to determine the appropriate application rate without exceeding
the maximum authorised application rate.
— The biocidal product shall be used for treatment of products (articles/mixtures) distributed only to
professional users.
4.14.2. Use-specific risk mitigation measures
— During handling phases of products from Meta SPC 1, 2, 3 and 4 (mixing and loading), exposure to the
product (corrosive and skin sensitizer products) has to be limited by use of PPE and application of technical
and organisational RMM:
— Minimisation of manual phases (process automation);
— Use of a dosing device;
— Regular cleaning of equipment and work area;
— Avoidance of contact with contaminated tools and objects;
42/227 ELI: http://data.europa.eu/eli/reg_impl/2025/2202/ojEN
OJ L, 20.11.2025
— Good standard of general ventilation;
— Training and management of staff on good practice.
— PPE is as follows:
— protective chemical resistant gloves (glove material to be specified by the authorisation holder within
the product information);
— protective coverall (at least type 3 or 4, EN 14605) which is impermeable for the biocidal product
shall be worn (coverall material to be specified by the authorisation holder within the product
information);
— Eye protection;
— Substance/task appropriate respirator if ventilation is inadequate.
— The maximal products concentration used for the preservation of functional fluids (hydraulic fluids,
antifreeze, corrosion inhibitors, etc…) being above the threshold value of 15 ppm, exposure has to be
limited by use of PPE, protecting skin and mucous membranes potentially exposed, and application of
technical and organisational RMM:
— Minimisation of manual phases;
— Use of a dosing device;
— Regular cleaning of equipment and work area;
— Good standard of general ventilation;
— Training and management of staff on good practice.
4.14.3. Where specific to the use, the particulars of likely direct or indirect effects, first aid instructions and emergency measures to
protect the environment
See general directions for use.
4.14.4. Where specific to the use, the instructions for safe disposal of the product and its packaging
See general directions for use.
4.14.5. Where specific to the use, the conditions of storage and shelf-life of the product under normal conditions of storage
See general directions for use.
4.15. Use description
Table 15
Preservation of laboratory reagents
Product type PT06: Preservatives for products during storage
Where relevant, an exact description of -
the authorised use
Target organism(s) (including Scientific name: no data
development stage) Common name: Bacteria
Development stage: no data
Scientific name: no data
Common name: Yeasts
Development stage: no data
ELI: http://data.europa.eu/eli/reg_impl/2025/2202/oj 43/227EN
OJ L, 20.11.2025
Field(s) of use indoor use
Preservation of laboratory reagents
.
The biocidal product is recommended to control the growth of
bacteria and yeasts in laboratory reagents.
Application method(s) Method: closed system
Detailed description:
Manual and automated dosing. The biocidal product should be
dispensed to the end use fluid at a point to ensure adequate mixing
using preferably automated metering pump or by manual addition.
Application rate(s) and frequency Application Rate:
Industrial uses: 1,5 - 14,5 % C(M)IT/MIT in the biocidal products.
Professional use: Add at typical use rate of 15,2 mg C(M)IT/MIT (3:1)
per kg final product to be treated.
-
Number and timing of application:
The biocidal product is added at single dose at the time of
manufacture, storage or shipment.
Slowly dispense using automated metering or manually. Mix
thoroughly until the biocidal product is evenly dispersed.
Industrial uses: 1,5 - 14,5 % C(M)IT/MIT in the biocidal products.
Professional use: Add at typical use rate of 15,2 mg C(M)IT/MIT (3:1)
per kg final product to be treated.
For the biocidal product as supplied: for industrial use only.
Category(ies) of users industrial
Pack sizes and packaging material For industrial and professional users:
— HDPE flask: 1 L
— HDPE flask: 5 L (nominal)
— HDPE Pail / Jerrycan: 10 L, 20 L, 25 L, 30 L (nominal)
— Box with HDPE liner: 20 L
— HDPE Drum: 110 L, 120 L, 200 L, 260 L
— HDPE IBC: 650 L, 800 L, 1 000 L, 1 250 L
All products should be transport and stored in a vented room.
4.15.1. Use-specific instructions for use
— The preservative can be added at any stage of the production of the product.
— Earliest possible addition is recommended for optimal protection.
— Consult the manufacturer to determine the optimal dosage for the various products to be preserved.
— It is recommended that the optimum biocide concentration and compatibility with individual formulations
is determined by means of laboratory tests.
44/227 ELI: http://data.europa.eu/eli/reg_impl/2025/2202/ojEN
OJ L, 20.11.2025
— The duration and storage conditions of the preserved matrices may impact the efficacy of the product,
microbiological tests should be conducted to determine the appropriate application rate without exceeding
the maximum authorised application rate.
— The biocidal product shall be used for treatment of products (articles/mixtures) distributed only to
professional users.
4.15.2. Use-specific risk mitigation measures
— During handling phases for products from Meta SPC 1, 3 and 4 (mixing and loading), exposure to the
product (corrosive and skin sensitizer products) has to be limited by use of PPE and application of technical
and organisational RMM:
— Minimisation of manual phases (process automation);
— Use of a dosing device;
— Regular cleaning of equipment and work area;
— Avoidance of contact with contaminated tools and objects;
— Good standard of general ventilation;
— Training and management of staff on good practice.
— PPE is as follows:
— protective chemical resistant gloves (glove material to be specified by the authorisation holder within
the product information);
— protective coverall (at least type 3 or 4, EN 14605) which is impermeable for the biocidal product
shall be worn (coverall material to be specified by the authorisation holder within the product
information);
— Eye protection;
— Substance/task appropriate respirator if ventilation is inadequate.
For professional users, the maximal products concentration used for the preservation of laboratory reagents being
above the threshold value of 15 ppm, exposure has to be limited by use of PPE, protecting skin and mucous
membranes potentially exposed, and application of technical and organisational RMM:
— Minimisation of manual phases;
— Use of a dosing device;
— Regular cleaning of equipment and work area;
— Good standard of general ventilation;
— Training and management of staff on good practice.
4.15.3. Where specific to the use, the particulars of likely direct or indirect effects, first aid instructions and emergency measures to
protect the environment
See general directions for use.
4.15.4. Where specific to the use, the instructions for safe disposal of the product and its packaging
See general directions for use.
4.15.5. Where specific to the use, the conditions of storage and shelf-life of the product under normal conditions of storage
See general directions for use.
ELI: http://data.europa.eu/eli/reg_impl/2025/2202/oj 45/227EN
OJ L, 20.11.2025
4.16. Use description
Table 16
Offline preservation of industrial reverse osmosis membranes
Product type PT06: Preservatives for products during storage
Where relevant, an exact description of -
the authorised use
Target organism(s) (including Scientific name: no data
development stage) Common name: Bacteria
Development stage: no data
Field(s) of use indoor use
Offline preservation of industrial reverse osmosis membranes
The biocidal product is recommended to control the growth of
bacteria of reverse osmosis and nanofiltration membranes producing
industrial water for extended periods of time.
Application method(s) Method: closed system
Detailed description:
Manual and automated dosing. The biocidal product should be
dispensed as a tankside additive into the circulating use-dilution of
the fluid, using a metering pump or by manual pouring, at a point to
ensure adequate mixing throughout the system. After complete filling
of the trains RO/NF systems with the biocide solution, pumps are
stopped (Off line treatment) for extended periods of time. Typically
C(M)IT/MIT (3:1) solutions are prepared in the CIP (cleaning in place)
tank and added via the dosing system. Dilution with permeate water
or high quality water is recommended for the preparation of the
biocide solution. Membranes should be soaked in the biocide solution
during the shut-down period.
Application rate(s) and frequency Application Rate:
7,5–20 g/m3 (ppm w/v) of C(M)IT/MIT (3:1).
-
Number and timing of application:
7,5–20 g/m3 (ppm w/v) of C(M)IT/MIT (3:1).
Category(ies) of users industrial
Pack sizes and packaging material For industrial and professional users:
— HDPE flask: 5 L (nominal)
— HDPE Pail / Jerrycan: 10 L, 20 L, 25 L, 30 L (nominal)
— Box with HDPE liner: 20 L
— HDPE Drum: 110 L, 120 L, 200 L, 260 L
— HDPE IBC: 650 L, 800 L, 1 000 L, 1 250 L
All products should be transport and stored in a vented room.
4.16.1. Use-specific instructions for use
— The preservative can be added at any stage of the production of the product.
— Earliest possible addition is recommended for optimal protection.
46/227 ELI: http://data.europa.eu/eli/reg_impl/2025/2202/ojEN
OJ L, 20.11.2025
— Consult the manufacturer to determine the optimal dosage for the various products to be preserved.
— It is recommended that the optimum biocide concentration and compatibility with individual formulations
is determined by means of laboratory tests.
— The duration and storage conditions of the preserved matrices may impact the efficacy of the product,
microbiological tests should be conducted to determine the appropriate application rate without exceeding
the maximum authorised application rate.
4.16.2. Use-specific risk mitigation measures
Rinse the system with water prior to perform the maintenance of the system.
— During handling phases for products from Meta SPC 1, 3 and 4 (mixing and loading), exposure to the
product (corrosive and skin sensitizer products) has to be limited by use of PPE and application of technical
and organisational RMM:
— Minimisation of manual phases (process automation);
— Use of a dosing device;
— Regular cleaning of equipment and work area;
— Avoidance of contact with contaminated tools and objects;
— Good standard of general ventilation;
— Training and management of staff on good practice.
— PPE is as follows:
— protective chemical resistant gloves (glove material to be specified by the authorisation holder within
the product information);
— protective coverall (at least type 3 or 4, EN 14605) which is impermeable for the biocidal product
shall be worn (coverall material to be specified by the authorisation holder within the product
information);
— Eye protection;
— Substance/task appropriate respirator if ventilation is inadequate.
4.16.3. Where specific to the use, the particulars of likely direct or indirect effects, first aid instructions and emergency measures to
protect the environment
See general directions for use.
4.16.4. Where specific to the use, the instructions for safe disposal of the product and its packaging
See general directions for use.
4.16.5. Where specific to the use, the conditions of storage and shelf-life of the product under normal conditions of storage
See general directions for use.
4.17. Use description
Table 17
Preservation of liquids used in closed recirculating cooling systems
Product type PT11: Preservatives for liquid-cooling and processing systems
ELI: http://data.europa.eu/eli/reg_impl/2025/2202/oj 47/227EN
OJ L, 20.11.2025
Where relevant, an exact description of -
the authorised use
Target organism(s) (including Scientific name: no data
development stage) Common name: Bacteria (including Legionella pneumophila)
Development stage: no data
Scientific name: no data
Common name: Yeasts
Development stage: no data
Scientific name: no data
Common name: fungi
Development stage: no data
Field(s) of use indoor use
outdoor use
Preservation of liquids used in closed recirculating cooling systems
(Closed re-circulating cooling water systems comprise compressor
cooling, air conditioning chilled water, boilers, engine jacket cooling,
power supply cooling, and other industrial processes).
The biocidal product is used to control the growth of aerobes and
anaerobes bacteria, yeast, fungi, and biofilm in the circulating water
of closed systems
Application method(s) Method: closed system
Detailed description:
Manual and automated dosing.
Application rate(s) and frequency Application Rate:
Curative efficacy:- against bacteria (including L. pneumophila) at 5 -
14,9 g C(M)IT/MIT (3:1) / m3 of water. Contact time: 24 hours -
against biofilm: 14,9 g C(M)IT/MIT (3:1) / m3 of water. Contact time:
24 hours.- against fungi and yeasts at 1 – 3 g C(M)IT/MIT (3:1) / m3
of water. Contact time: 48 hours. Preventive efficacy:- against bacteria
(including L. pneumophila) at 3 – 14,9 g C(M)IT/MIT (3:1) / m3 of
water. - against biofilm (including L. pneumophila): 3 g C(M)IT/MIT
(3:1) / m3 of water.
-
Number and timing of application:
Curative efficacy:
— against bacteria (including L. pneumophila) at 5 - 14,9 g C(M)
IT/MIT (3:1) / m3 of water.
Contact time: 24 hours
— against biofilm: 14,9 g C(M)IT/MIT (3:1) / m3 of water.
Contact time: 24 hours
— against fungi and yeasts at 1 – 3 g C(M)IT/MIT (3:1) / m3 of water.
Contact time: 48 hours
Preventive efficacy:
against bacteria (including L. pneumophila) at 3 – 14,9 g C(M)IT/MIT
(3:1) / m3 of water.
against biofilm (including L. pneumophila): 3 g C(M)IT/MIT (3:1) /
m3 of water.
48/227 ELI: http://data.europa.eu/eli/reg_impl/2025/2202/ojEN
OJ L, 20.11.2025
Category(ies) of users industrial
Pack sizes and packaging material For industrial and professional users:
— HDPE flask: 5 L (nominal)
— HDPE Pail / Jerrycan: 10 L, 20 L, 25 L, 30 L (nominal)
— Box with HDPE liner: 20 L
— HDPE Drum: 110 L, 120 L, 200 L, 260 L
— HDPE IBC: 650 L, 800 L, 1 000 L, 1 250 L
All products should be transport and stored in a vented room.
4.17.1. Use-specific instructions for use
Microbiological tests to prove adequacy of preservation have to be undertaken by the user of C(M)IT/MIT products
in order to determine the effective dose of the preservative for the specific matrix/location/system. If needed,
consult the manufacturer of the preservative product.
4.17.2. Use-specific risk mitigation measures
— Rinse the system (especially the dispensing pumps) with water prior to perform the cleaning step.
— During handling phases (mixing and loading) and cleaning of the dispensing pumps, exposure to the
product (corrosive and skin sensitizer product) has to be limited by use of PPE and application of technical
and organisational RMM:
— Minimisation of manual phases (process automation);
— Use of a dosing device;
— Regular cleaning of equipment and work area;
— Avoidance of contact with contaminated tools and objects;
— Good standard of general ventilation;
— Training and management of staff on good practice.
— PPE is as follows:
— protective chemical resistant gloves (glove material to be specified by the authorisation holder within
the product information);
— protective coverall (at least type 3 or 4, EN 14605) which is impermeable for the biocidal product
shall be worn (coverall material to be specified by the authorisation holder within the product
information);
— Eye protection;
— Substance/task appropriate respirator if ventilation is inadequate.
4.17.3. Where specific to the use, the particulars of likely direct or indirect effects, first aid instructions and emergency measures to
protect the environment
See general directions for use.
4.17.4. Where specific to the use, the instructions for safe disposal of the product and its packaging
See general directions for use.
ELI: http://data.europa.eu/eli/reg_impl/2025/2202/oj 49/227EN
OJ L, 20.11.2025
4.17.5. Where specific to the use, the conditions of storage and shelf-life of the product under normal conditions of storage
See general directions for use.
4.18. Use description
Table 18
Preservation of liquids used in small open recirculating cooling systems
Product type PT11: Preservatives for liquid-cooling and processing systems
Where relevant, an exact description of -
the authorised use
Target organism(s) (including Scientific name: no data
development stage) Common name: Bacteria (including Legionella pneumophila)
Development stage: no data
Scientific name: no data
Common name: Yeasts
Development stage: no data
Scientific name: no data
Common name: fungi
Development stage: no data
Scientific name: no data
Common name: Algae (green algae and cyanobacteria)
Development stage: no data
Field(s) of use indoor use
outdoor use
Preservation of liquids used in small open recirculating cooling
systems (blowdown and recirculating flow rates, as well as total
volume of water limited to 2 m3/h, and 100 m3/h and 300 m3
respectively)
Process and cooling water: Used to control the growth of bacteria,
algae, fungi and biofilm
Application method(s) Method: open system
Detailed description:
Manual and automated dosing. .
Application rate(s) and frequency Application Rate:
Curative treatment Against bacteria (including L. pneumophila) at 5 –
14,9 g C(M)IT/MIT (3:1) / m3 of water , - against biofilm (including L.
pneumophila) at 1,5 to 14,9 g C(M)IT/MIT (3:1) / m3 of water, -
against fungi (including yeast) at 1 – 14,9 g C(M)IT/MIT (3:1) / m3 of
water. Preventive treatment: - Against bacteria, green algae and
cyanobacteria at 3 g C(M)IT/MIT (3:1) / m3 of water, - against biofilm
(including L. pneumophila) at 3 g C(M)IT/MIT (3:1) / m3 of water.
-
Number and timing of application:
Curative treatment:
— Against bacteria (including L. pneumophila) at 5 – 14,9 g C(M)
IT/MIT (3:1) / m3 of water
50/227 ELI: http://data.europa.eu/eli/reg_impl/2025/2202/ojEN
OJ L, 20.11.2025
Contact time: 24 hours
— against biofilm (including L. pneumophila) at 1,5 - 14,9 g C(M)
IT/MIT (3:1) / m3 of water
Contact time: 48 hours.
— against fungi and yeast at 1 – 14,9 g C(M)IT/MIT (3:1) / m3 of
water
Contact time: 48 hours.
Preventive treatment:
— against bacteria, green algae and cyanobacteria at 3 g C(M)IT/MIT
(3:1) / m3 of water.
— against biofilm (including L. pneumophila) at 3 g C(M)IT/MIT (3:1)
/ m3 of water.
Category(ies) of users industrial
Pack sizes and packaging material For industrial and professional users:
— HDPE flask: 5 L (nominal)
— HDPE Pail / Jerrycan: 10 L, 20 L, 25 L, 30 L (nominal)
— Box with HDPE liner: 20 L
— HDPE Drum: 110 L, 120 L, 200 L, 260 L
— HDPE IBC: 650 L, 800 L, 1 000 L, 1 250 L
All products should be transport and stored in a vented room.
4.18.1. Use-specific instructions for use
Microbiological tests to prove adequacy of preservation have to be undertaken by the user of C(M)IT/MIT products
in order to determine the effective dose of the preservative for the specific matrix/location/system. If needed,
consult the manufacturer of the preservative product.
4.18.2. Use-specific risk mitigation measures
— Rinse the system (especially the dispensing pumps) with water prior to perform the cleaning step.
— During handling phases (mixing and loading) and cleaning of the dispensing pumps, exposure to the
product (corrosive and skin sensitizer product) has to be limited by use of PPE and application of technical
and organisational RMM:
— Minimisation of manual phases (process automation);
— Use of a dosing device;
— Regular cleaning of equipment and work area;
— Avoidance of contact with contaminated tools and objects;
— Good standard of general ventilation;
— Training and management of staff on good practice.
— PPE is as follows:
— protective chemical resistant gloves (glove material to be specified by the authorisation holder within
the product information);
— protective coverall (at least type 3 or 4, EN 14605) which is impermeable for the biocidal product
shall be worn (coverall material to be specified by the authorisation holder within the product
information);
ELI: http://data.europa.eu/eli/reg_impl/2025/2202/oj 51/227EN
OJ L, 20.11.2025
— Eye protection;
— Substance/task appropriate respirator if ventilation is inadequate.
— Cooling fluid must not enter surface water directly. Use product only in premises that are connected to
a STP.
— The product can only be used when the cooling towers are equipped with drift eliminators that reduce the
drift at least by 99%.
4.18.3. Where specific to the use, the particulars of likely direct or indirect effects, first aid instructions and emergency measures to
protect the environment
See general directions for use.
4.18.4. Where specific to the use, the instructions for safe disposal of the product and its packaging
See general directions for use.
4.18.5. Where specific to the use, the conditions of storage and shelf-life of the product under normal conditions of storage
See general directions for use.
4.19. Use description
Table 19.
Preservation of liquids used in pasteurizers, conveyor belts and air washers
Product type PT11: Preservatives for liquid-cooling and processing systems
Where relevant, an exact description of -
the authorised use
Target organism(s) (including Scientific name: no data
development stage) Common name: Bacteria (including Legionella pneumophila)
Development stage: no data
Scientific name: no data
Common name: Yeasts
Development stage: no data
Scientific name: no data
Common name: fungi
Development stage: no data
Scientific name: no data
Common name: Algae (green algae and cyanobacteria)
Development stage: no data
Field(s) of use indoor use
outdoor use
Preservation of liquids used in non-food pasteurizers and conveyor
belts, air washers.
Application method(s) Method: -
Detailed description:
The biocidal product is dosed automatically in the heat transfer fluid,
in a place of good mixing (e.g. collecting sump below the conveyor
belt). The feeding pipe is used to dose the biocidal product below the
water level in order to limit its evaporation.
52/227 ELI: http://data.europa.eu/eli/reg_impl/2025/2202/ojEN
OJ L, 20.11.2025
Application rate(s) and frequency Application Rate:
Curative treatment: -against bacteria (including L. pneumophila): 5 -
14,9 g C(M)IT/MIT (3:1) / m3 of water - against biofilm (including L.
pneumophila) at 1,5 - 14,9 g C(M)IT/MIT (3:1) / m3 of water - against
fungi and yeast at 1 – 14,9 g C(M)IT/MIT (3:1) / m3 of water.
Preventive treatment: Against bacteria, green algae and cyanobacteria
at 3 g C(M)IT/MIT (3:1) / m3 of water, against biofilm (including L.
pneumophila) at 3 g C(M)IT/MIT (3:1) / m3 of water.
-
Number and timing of application:
Curative treatment:
against bacteria (including L. pneumophila): 5 - 14,9 g C(M)IT/MIT
(3:1) / m3 of water.
Contact time: 24 hours
— against biofilm (including L. pneumophila) at 1,5 - 14,9 g C(M)
IT/MIT (3:1) / m3 of water
Contact time: 48 hours.
— against fungi and yeast at 1 – 14,9 g C(M)IT/MIT (3:1) / m3 of
water
Contact time: 48 hours.
Preventive treatment:
— Against bacteria, green algae and cyanobacteria at 3 g C(M)IT/MIT
(3:1) / m3 of water.
— against biofilm (including L. pneumophila) at 3 g C(M)IT/MIT (3:1)
/ m3 of water.
Category(ies) of users industrial
Pack sizes and packaging material For industrial and professional users:
— HDPE flask: 5 L (nominal)
— HDPE Pail / Jerrycan: 10 L, 20 L, 25 L, 30 L (nominal)
— Box with HDPE liner: 20 L
— HDPE Drum: 110 L, 120 L, 200 L, 260 L
— HDPE IBC: 650 L, 800 L, 1 000 L, 1 250 L
All products should be transport and stored in a vented room.
4.19.1. Use-specific instructions for use
Microbiological tests to prove adequacy of preservation have to be undertaken by the user of C(M)IT/MIT products
in order to determine the effective dose of the preservative for the specific matrix/location/system. If needed,
consult the manufacturer of the preservative product.
Air washers: For use only in industrial air-washer systems that maintain effective mist eliminating components.
4.19.2. Use-specific risk mitigation measures
— Rinse the system (especially the dispensing pumps) with water prior to perform the cleaning step.
ELI: http://data.europa.eu/eli/reg_impl/2025/2202/oj 53/227EN
OJ L, 20.11.2025
— During handling phases (mixing and loading) and cleaning of the dispensing pumps, exposure to the
product (corrosive and skin sensitizer product) has to be limited by use of PPE and application of technical
and organisational RMM:
— Minimisation of manual phases (process automation);
— Use of a dosing device;
— Regular cleaning of equipment and work area;
— Avoidance of contact with contaminated tools and objects;
— Good standard of general ventilation;
— Training and management of staff on good practice.
— PPE is as follows:
— protective chemical resistant gloves (glove material to be specified by the authorisation holder within
the product information);
— protective coverall (at least type 3 or 4, EN 14605) which is impermeable for the biocidal product
shall be worn (coverall material to be specified by the authorisation holder within the product
information);
— Eye protection;
— Substance/task appropriate respirator if ventilation is inadequate.
4.19.3. Where specific to the use, the particulars of likely direct or indirect effects, first aid instructions and emergency measures to
protect the environment
See general directions for use.
4.19.4. Where specific to the use, the instructions for safe disposal of the product and its packaging
See general directions for use.
4.19.5. Where specific to the use, the conditions of storage and shelf-life of the product under normal conditions of storage
See general directions for use.
4.20. Use description
Table 20
Preservation of wood treatment solutions
Product type PT11: Preservatives for liquid-cooling and processing systems
Where relevant, an exact description of -
the authorised use
Target organism(s) (including Scientific name: fungi
development stage) Common name: other
Development stage: no data
Field(s) of use indoor use
outdoor use
Preservation of wood treatment solutions for application on wood of
classes 1, 2 and 3 only. The biocidal product is used as a preservative
for aqueous wood preservative treatment solution during the wet-
state process used in timber treatment solutions.
54/227 ELI: http://data.europa.eu/eli/reg_impl/2025/2202/ojEN
OJ L, 20.11.2025
Application method(s) Method: -
Detailed description:
-
Application rate(s) and frequency Application Rate:
Preventive treatment: against fungi: 15 - 50 g C(M)IT/MIT (3:1) / m3
of in use wood preservation solution
-
Number and timing of application:
Preventive treatment: against fungi: 15 - 50 g C(M)IT/MIT (3:1) / m3
of in use wood preservation solution
Category(ies) of users industrial
Pack sizes and packaging material For industrial and professional users:
— HDPE flask: 5 L (nominal)
— HDPE Pail / Jerrycan: 10 L, 20 L, 25 L, 30 L (nominal)
— Box with HDPE liner: 20 L
— HDPE Drum: 110 L, 120 L, 200 L, 260 L
— HDPE IBC: 650 L, 800 L, 1 000 L, 1 250 L
All products should be transport and stored in a vented room.
4.20.1. Use-specific instructions for use
Microbiological tests to prove adequacy of preservation have to be undertaken by the user of C(M)IT/MIT products
in order to determine the effective dose of the preservative for the specific matrix/location/system. If needed,
consult the manufacturer of the preservative product.
— The biocidal product is not intended to function as a wood preservative against wood destroying fungus
relative to product type 8.
4.20.2. Use-specific risk mitigation measures
— During handling phases (mixing and loading) and cleaning phases, exposure to the product (corrosive and
skin sensitizer product) has to be limited by use of PPE and application of technical and organisational RMM:
— Minimisation of manual phases (process automation);
— Use of a dosing device;
— Regular cleaning of equipment and work area;
— Avoidance of contact with contaminated tools and objects;
— Good standard of general ventilation;
— Training and management of staff on good practice.
— PPE is as follows:
— protective chemical resistant gloves (glove material to be specified by the authorisation holder within
the product information);
— protective coverall (at least type 3 or 4, EN 14605) which is impermeable for the biocidal product
shall be worn (coverall material to be specified by the authorisation holder within the product
information);
— Eye protection;
— Substance/task appropriate respirator if ventilation is inadequate.
ELI: http://data.europa.eu/eli/reg_impl/2025/2202/oj 55/227EN
OJ L, 20.11.2025
— The product shall not be used in a wood treatment solution to be applied to wood which may come in direct
contact with food, feeding stuff and livestock animals
— The product can be used to preserve wood treatment solutions for the treatment of wood in use classes 1, 2
and 3 only.
— The product can be used in a wood treatment solution where the industrial application processes of wood
treatment can be carried out within a contained area situated on impermeable hard standing with bunding
to prevent run-off and a recovery system in place (e.g. sump).
— The product can be used in wood treatment solutions for the preservation of freshly treated timber, which
after treatment is stored under shelter or on impermeable hard standing, or both, to prevent direct losses to
soil, sewer or water. Any losses of wood treatment solution shall be collected for reuse or disposal.
— The product can be used only in wood treatment solutions for industrial application if these cannot be
released to soil, ground- and surface water or any kind of sewer and the wood treatment solutions and/or
the product are collected and reused or disposed of as hazardous waste.
— The biocidal product can be used only in wood treatment solutions used for the treatment of objects or
materials which are stored until completely dried on impermeable ground and under roof, to avoid leakage
into the soil.
4.20.3. Where specific to the use, the particulars of likely direct or indirect effects, first aid instructions and emergency measures to
protect the environment
See general directions for use.
4.20.4. Where specific to the use, the instructions for safe disposal of the product and its packaging
See general directions for use.
4.20.5. Where specific to the use, the conditions of storage and shelf-life of the product under normal conditions of storage
See general directions for use.
4.21. Use description
Table 21
Preservation of recirculating fluids used in textile and fiber processing, leather processing, photo-
processing and fountain solution systems
Product type PT11: Preservatives for liquid-cooling and processing systems
Where relevant, an exact description of -
the authorised use
Target organism(s) (including Scientific name: no data
development stage) Common name: Bacteria
Development stage: no data
56/227 ELI: http://data.europa.eu/eli/reg_impl/2025/2202/ojEN
OJ L, 20.11.2025
Field(s) of use indoor use
Preservation of recirculating fluids used in textile, fiber processing,
leather processing, photo-processing and fountain solution systems
C(M)IT/MIT (3:1) biocidal products are used for the preservation of
textile and spinning fluids, photo processing solutions, leather
process (e.g. washing and soaking treatment stages) and printing
fountain solutions to control the integrity of recirculating fluid by
reducing microbial contamination in the bulk solution.
Application method(s) Method: -
Detailed description:
Manual and automated dosing.The preservation of all end-products is
performed in most cases highly automated by industrial usersThe
biocidal product is added to the central sump, basin or recirculating
lines in an area with adequate mixing.
Application rate(s) and frequency Application Rate:
Curative treatment: Against bacteria at 16-30 mg C(M)IT/MIT (3:1)
per L of fluid
-
Number and timing of application:
Curative treatment: Against bacteria at 16-30 mg C(M)IT/MIT (3:1)
per L of fluid
Contact time 5 days
Category(ies) of users industrial
Pack sizes and packaging material For industrial and professional users:
— HDPE flask: 5 L (nominal)
— HDPE Pail / Jerrycan: 10 L, 20 L, 25 L, 30 L (nominal)
— Box with HDPE liner: 20 L
— HDPE Drum: 110 L, 120 L, 200 L, 260 L
— HDPE IBC: 650 L, 800 L, 1 000 L, 1 250 L
All products should be transport and stored in a vented room.
4.21.1. Use-specific instructions for use
Microbiological tests to prove adequacy of preservation have to be undertaken by the user of C(M)IT/MIT products
in order to determine the effective dose of the preservative for the specific matrix/location/system. If needed,
consult the manufacturer of the preservative product.
4.21.2. Use-specific risk mitigation measures
— Rinse the system (especially the dispensing pumps) with water prior to perform the cleaning step.
— During handling phases (mixing and loading) and cleaning of the dispensing pumps, exposure to the
product (corrosive and skin sensitizer product) has to be limited by use of PPE and application of technical
and organisational RMM:
— Minimisation of manual phases (process automation);
— Use of a dosing device;
— Regular cleaning of equipment and work area;
— Avoidance of contact with contaminated tools and objects;
— Good standard of general ventilation;
— Training and management of staff on good practice.
ELI: http://data.europa.eu/eli/reg_impl/2025/2202/oj 57/227EN
OJ L, 20.11.2025
— PPE is as follows:
— protective chemical resistant gloves (glove material to be specified by the authorisation holder within
the product information);
— protective coverall (at least type 3 or 4, EN 14605) which is impermeable for the biocidal product
shall be worn (coverall material to be specified by the authorisation holder within the product
information);
— Eye protection;
— Substance/task appropriate respirator if ventilation is inadequate.
— Liquids used in textile and fiber processing fluids must not enter surface water directly. Use product only in
premises that are connected to a STP.
— Recirculating liquids in photoprocessing systems and fountain solution systems must not enter surface water
directly. Use product only in premises that are connected to a STP.
4.21.3. Where specific to the use, the particulars of likely direct or indirect effects, first aid instructions and emergency measures to
protect the environment
See general directions for use.
4.21.4. Where specific to the use, the instructions for safe disposal of the product and its packaging
See general directions for use.
4.21.5. Where specific to the use, the conditions of storage and shelf-life of the product under normal conditions of storage
See general directions for use.
4.22. Use description
Table 22
Preservation of re-circulating liquids used in paint spray booths and electrodeposition coating systems
Product type PT11: Preservatives for liquid-cooling and processing systems
Where relevant, an exact description of -
the authorised use
Target organism(s) (including Scientific name: no data
development stage) Common name: Bacteria
Development stage: no data
Scientific name: no data
Common name: Yeasts
Development stage: no data
Field(s) of use indoor use
Preservation of re-circulating liquids used in paint spray booths and
electrodeposition coating systems.
58/227 ELI: http://data.europa.eu/eli/reg_impl/2025/2202/ojEN
OJ L, 20.11.2025
The biocidal product is used for preservation of fluids in pre-
treatment processes (Cleaning treatment for grease removal and soil,
degreasing Phosphating process, Rinse off tanks) paint spray booths
and electrodeposition coating systems (e.g. cataphoretic baths)
applied in Car Refinishing and Original equipment Car
Manufacturing to control the integrity of recirculating fluid by
reducing microbial contamination from bacteria and fungi in the
bulk solution.
Application method(s) Method: -
Detailed description:
-
Application rate(s) and frequency Application Rate:
Preventive treatment: 7,5 to 30 mg C(M)IT/MIT (3:1) per Kg final
product.
-
Number and timing of application:
Preventive treatment: 7,5 to 30 mg C(M)IT/MIT (3:1) per Kg final
product.
The biocidal product is added at the time of manufacture, storage or
shipment.
Category(ies) of users industrial
Pack sizes and packaging material For industrial and professional users:
— HDPE flask: 5 L (nominal)
— HDPE Pail / Jerrycan: 10 L, 20 L, 25 L, 30 L (nominal)
— Box with HDPE liner: 20 L
— HDPE Drum: 110 L, 120 L, 200 L, 260 L
— HDPE IBC: 650 L, 800 L, 1 000 L, 1 250 L
All products should be transport and stored in a vented room.
4.22.1. Use-specific instructions for use
Microbiological tests to prove adequacy of preservation have to be undertaken by the user of C(M)IT/MIT products
in order to determine the effective dose of the preservative for the specific matrix/location/system. If needed,
consult the manufacturer of the preservative product.
4.22.2. Use-specific risk mitigation measures
— Rinse the system (especially the dispensing pumps) with water prior to perform the cleaning step.
— During handling phases (mixing and loading) and cleaning of the dispensing pumps, exposure to the
product (corrosive and skin sensitizer product) has to be limited by use of PPE and application of technical
and organisational RMM:
— Minimisation of manual phases (process automation);
— Use of a dosing device;
— Regular cleaning of equipment and work area;
— Avoidance of contact with contaminated tools and objects;
— Good standard of general ventilation;
— Training and management of staff on good practice.
ELI: http://data.europa.eu/eli/reg_impl/2025/2202/oj 59/227EN
OJ L, 20.11.2025
— PPE is as follows:
— protective chemical resistant gloves (glove material to be specified by the authorisation holder within
the product information);
— protective coverall (at least type 3 or 4, EN 14605) which is impermeable for the biocidal product
shall be worn (coverall material to be specified by the authorisation holder within the product
information);
— Eye protection;
— Substance/task appropriate respirator if ventilation is inadequate.
4.22.3. Where specific to the use, the particulars of likely direct or indirect effects, first aid instructions and emergency measures to
protect the environment
See general directions for use.
4.22.4. Where specific to the use, the instructions for safe disposal of the product and its packaging
See general directions for use.
4.22.5. Where specific to the use, the conditions of storage and shelf-life of the product under normal conditions of storage
See general directions for use.
4.23. Use description
Table 23
Preservation of liquids used in closed recirculating heating systems and associated pipework
Product type PT11: Preservatives for liquid-cooling and processing systems
Where relevant, an exact description of -
the authorised use
Target organism(s) (including Scientific name: no data
development stage) Common name: Bacteria (anaerobes and aerobes (including
Legionella pneumophila)
Development stage: no data
Scientific name: no data
Common name: Yeasts
Development stage: no data
Scientific name: no data
Common name: fungi
Development stage: no data
Field(s) of use indoor use
outdoor use
Preservation of liquids used in closed recirculating heating systems
and associated pipework. Pre-commission biocide flushing of new or
existing pipework systems (heating and chilling pipework) includes
used or new structural pipework built on industrial building projects.
60/227 ELI: http://data.europa.eu/eli/reg_impl/2025/2202/ojEN
OJ L, 20.11.2025
Closed recirculating heating systems: pre-commission biocidal
product flushing of new or existing pipework systems (heating and
chilling pipework) includes used or new structural pipework built on
industrial building projects. The biocidal product is used to control
the growth of aerobic and anaerobic bacteria, fungi and biofilm in the
circulating water of closed systems. Closed systems are less
susceptible to corrosion, scaling and biological fouling than open
systems. However microbial problems can occur, if the system is left
filled and untreated. This is due to the presence of nitrite and glycols
used as nutrients by microbes.
Application method(s) Method: closed system
Detailed description:
Manual and automated dosing. The biocidal product is dosed
automatically in the heat transfer fluid, in a place of good mixing.
The feeding pipe must dose the biocidal product below the water
level in order to limit the evaporation of the biocidal product.
Application rate(s) and frequency Application Rate:
Curative treatment - against bacteria at 5 g C(M)IT/MIT (3:1) / m3 of
water (including L. pneumophila) - against biofilm at 14,9 g C(M)
IT/MIT (3:1) / m3 of water - against fungi and yeast at 1 g C(M)IT/MIT
/ m3 of water Preventive treatment - against bacteria (including L.
pneumophila) at 3 g C(M)IT/MIT (3:1) / m3 of water - against biofilm
at 3 g C(M)IT/MIT (3:1) / m3 of water.
-
Number and timing of application:
Curative treatment:
— against bacteria at 5 g C(M)IT/MIT (3:1) / m3 of water (including L.
pneumophila)
Contact time: 24 hours
— against biofilm at 14,9 g C(M)IT/MIT (3:1) / m3 of water
Contact time: 24 hours
— against fungi and yeast at 1 g C(M)IT/MIT / m3 of water Contact
time: 48 hours
Preventive treatment
— against bacteria (including L. pneumophila) at 3 g C(M)IT/MIT
(3:1) / m3 of water and against biofilm at 3 g C(M)IT/MIT (3:1) /
m3 of water.
Category(ies) of users industrial
Pack sizes and packaging material For industrial and professional users:
— HDPE flask: 5 L (nominal)
— HDPE Pail / Jerrycan: 10 L, 20 L, 25 L, 30 L (nominal)
— Box with HDPE liner: 20 L
— HDPE Drum: 110 L, 120 L, 200 L, 260 L
— HDPE IBC: 650 L, 800 L, 1 000 L, 1 250 L
All products should be transport and stored in a vented room.
ELI: http://data.europa.eu/eli/reg_impl/2025/2202/oj 61/227EN
OJ L, 20.11.2025
4.23.1. Use-specific instructions for use
Microbiological tests to prove adequacy of preservation have to be undertaken by the user of C(M)IT/MIT products
in order to determine the effective dose of the preservative for the specific matrix/location/system. If needed,
consult the manufacturer of the preservative product.
4.23.2. Use-specific risk mitigation measures
— Rinse the system (especially the dispensing pumps) with water prior to perform the cleaning step.
— During handling phases (mixing and loading) and cleaning of the dispensing pumps, exposure to the
product (corrosive and skin sensitizer product) has to be limited by use of PPE and application of technical
and organisational RMM:
— Minimisation of manual phases (process automation);
— Use of a dosing device;
— Regular cleaning of equipment and work area;
— Avoidance of contact with contaminated tools and objects;
— Good standard of general ventilation;
— Training and management of staff on good practice.
— PPE is as follows:
— protective chemical resistant gloves (glove material to be specified by the authorisation holder within
the product information);
— protective coverall (at least type 3 or 4, EN 14605) which is impermeable for the biocidal product
shall be worn (coverall material to be specified by the authorisation holder within the product
information);
— Eye protection;
— Substance/task appropriate respirator if ventilation is inadequate.
4.23.3. Where specific to the use, the particulars of likely direct or indirect effects, first aid instructions and emergency measures to
protect the environment
See general directions for use.
4.23.4. Where specific to the use, the instructions for safe disposal of the product and its packaging
See general directions for use.
4.23.5. Where specific to the use, the conditions of storage and shelf-life of the product under normal conditions of storage
See general directions for use.
62/227 ELI: http://data.europa.eu/eli/reg_impl/2025/2202/ojEN
OJ L, 20.11.2025
4.24. Use description
Table 24
Preservation of polymers used in oilfield processes (e.g. enhanced oil recovery, drilling muds, etc.)
Product type PT11: Preservatives for liquid-cooling and processing systems
Where relevant, an exact description of -
the authorised use
Target organism(s) (including Scientific name: no data
development stage) Common name: Bacteria
Development stage: no data
Field(s) of use outdoor use
Preservation of polymers used in oilfield processes (e.g. enhanced oil
recovery, drilling muds, etc.)
Application method(s) Method: -
Detailed description:
-
Application rate(s) and frequency Application Rate:
Preventive treatment of polymers used in the injection water:
Xanthan polymer: 30 -50 g C(M)IT/MIT/m3 solution. HPAM
polymer: 30 - 50 g C(M)IT/MIT/m3 solution. Preventive treatment of
polymers used in the drilling muds: Xanthan polymer: 30 g C(M)IT/
MIT/m3 solution. HPAM polymer: 30 g C(M)IT/MIT/m3 solution.
-
Number and timing of application:
Preventive treatment of polymers used in the injection water:
Xanthan polymer: 30 -50 g C(M)IT/MIT/m3 solution.
HPAM polymer: 30 - 50 g C(M)IT/MIT/m3 solution.
Preventive treatment of polymers used in the drilling muds:
Xanthan polymer: 30 g C(M)IT/MIT/m3 solution.
HPAM polymer: 30 g C(M)IT/MIT/m3 solution.
Category(ies) of users industrial
Pack sizes and packaging material For industrial and professional users:
— HDPE flask: 5 L (nominal)
— HDPE Pail / Jerrycan: 10 L, 20 L, 25 L, 30 L (nominal)
— Box with HDPE liner: 20 L
— HDPE Drum: 110 L, 120 L, 200 L, 260 L
— HDPE IBC: 650 L, 800 L, 1 000 L, 1 250 L
All products should be transport and stored in a vented room.
4.24.1. Use-specific instructions for use
Microbiological tests to prove adequacy of preservation have to be undertaken by the user of C(M)IT/MIT products
in order to determine the effective dose of the preservative for the specific matrix/location/system. If needed,
consult the manufacturer of the preservative product.
ELI: http://data.europa.eu/eli/reg_impl/2025/2202/oj 63/227EN
OJ L, 20.11.2025
4.24.2. Use-specific risk mitigation measures
— Rinse the system (especially the dispensing pumps) with water prior to perform the cleaning step.
— During handling phases (mixing and loading) and cleaning of the dispensing pumps, exposure to the
product (corrosive and skin sensitizer product) has to be limited by use of PPE and application of technical
and organisational RMM:
— Minimisation of manual phases (process automation);
— Use of a dosing device;
— Regular cleaning of equipment and work area;
— Avoidance of contact with contaminated tools and objects;
— Good standard of general ventilation;
— Training and management of staff on good practice.
— PPE is as follows:
— protective chemical resistant gloves (glove material to be specified by the authorisation holder within
the product information);
— protective coverall (at least type 3 or 4, EN 14605) which is impermeable for the biocidal product
shall be worn (coverall material to be specified by the authorisation holder within the product
information);
— Eye protection;
— Substance/task appropriate respirator if ventilation is inadequate.
4.24.3. Where specific to the use, the particulars of likely direct or indirect effects, first aid instructions and emergency measures to
protect the environment
See general directions for use.
4.24.4. Where specific to the use, the instructions for safe disposal of the product and its packaging
See general directions for use.
4.24.5. Where specific to the use, the conditions of storage and shelf-life of the product under normal conditions of storage
See general directions for use.
4.25. Use description
Table 25
Slimicide treatment in the de-inking process of the pulp and paper
Product type PT12: Slimicides
Where relevant, an exact description of -
the authorised use
Target organism(s) (including Scientific name: no data
development stage) Common name: Bacteria
Development stage: no data
Scientific name: no data
Common name: Yeasts
Development stage: no data
64/227 ELI: http://data.europa.eu/eli/reg_impl/2025/2202/ojEN
OJ L, 20.11.2025
Scientific name: no data
Common name: fungi
Development stage: no data
Field(s) of use indoor use
Slimicide treatment in the de-inking process of the pulp and paper.
Recycling paper /deinking paper mills. Deinking process is a
manufacturing paper process of removing printing inks from waste
paper-fibers to produce deinked pulp.
Application method(s) Method: closed system
Detailed description:
Manual and automated dosing. The biocidal product is automatically
dosed by pump and fixed pipes into the circuit, usually in the pulper
below the water level.
Application rate(s) and frequency Application Rate:
Curative treatment: 10 to 14,9 g C(M)IT/MIT (3:1) / m3 of water to
be treated. Preventive treatment: 5 g C(M)IT/MIT (3:1) / m3 of water
to be treated.
-
Number and timing of application:
Curative treatment: 10 to 14,9 g C(M)IT/MIT (3:1) / m3 of water to
be treated
Contact time: 24 hours
Preventive treatment: 5 g C(M)IT/MIT (3:1) / m3 of water to be
treated.
Category(ies) of users industrial
Pack sizes and packaging material For industrial and professional users:
— HDPE flask: 5 L (nominal)
— HDPE Pail / Jerrycan: 10 L, 20 L, 25 L, 30 L (nominal)
— Box with HDPE liner: 20 L
— HDPE Drum: 110 L, 120 L, 200 L, 260 L
— HDPE IBC: 650 L, 800 L, 1 000 L, 1 250 L
All products should be transport and stored in a vented room.
4.25.1. Use-specific instructions for use
Microbiological tests to prove adequacy of preservation have to be undertaken by the user of C(M)IT/MIT products
in order to determine the effective dose of the preservative for the specific matrix/location/system. If needed,
consult the manufacturer of the preservative product.
4.25.2. Use-specific risk mitigation measures
— Rinse the system (especially the dispensing pumps) with water prior to perform the cleaning step.
— During handling phases (mixing and loading) and cleaning of the dispensing pumps, exposure to the
product (corrosive and skin sensitizer product) has to be limited by use of PPE and application of technical
and organisational RMM:
— Minimisation of manual phases (process automation);
— Use of a dosing device;
ELI: http://data.europa.eu/eli/reg_impl/2025/2202/oj 65/227EN
OJ L, 20.11.2025
— Regular cleaning of equipment and work area;
— Avoidance of contact with contaminated tools and objects;
— Good standard of general ventilation;
— Training and management of staff on good practice.
— PPE is as follows:
— protective chemical resistant gloves (glove material to be specified by the authorisation holder within
the product information);
— protective coverall (at least type 3 or 4, EN 14605) which is impermeable for the biocidal product
shall be worn (coverall material to be specified by the authorisation holder within the product
information);
— Eye protection;
— Substance/task appropriate respirator if ventilation is inadequate.
4.25.3. Where specific to the use, the particulars of likely direct or indirect effects, first aid instructions and emergency measures to
protect the environment
See general directions for use.
4.25.4. Where specific to the use, the instructions for safe disposal of the product and its packaging
See general directions for use.
4.25.5. Where specific to the use, the conditions of storage and shelf-life of the product under normal conditions of storage
See general directions for use.
4.26. Use description
Table 26
Slimicide treatment in the wet-end stage of paper manufacturing process
Product type PT12: Slimicides
Where relevant, an exact description of -
the authorised use
Target organism(s) (including Scientific name: no data
development stage) Common name: Bacteria
Development stage: no data
Scientific name: no data
Common name: Yeasts
Development stage: no data
Scientific name: no data
Common name: fungi
Development stage: no data
Field(s) of use indoor use
Slimicide treatment in the wet-end stage of the paper manufacturing
process (paper mills, wet-end stage (water circuits), and paper mills
process system).
Application method(s) Method: closed system
Detailed description:
Manual and automated dosing.
66/227 ELI: http://data.europa.eu/eli/reg_impl/2025/2202/ojEN
OJ L, 20.11.2025
Application rate(s) and frequency Application Rate:
Curative treatment: 10 to 14,9 g C(M)IT/MIT (3:1) / m3 of water to
be treated. Preventive treatment: 5 g C(M)IT/MIT (3:1) / m3 of water
to be treated.
-
Number and timing of application:
Curative treatment: 10 to 14,9 g C(M)IT/MIT (3:1) / m3 of water to
be treated
Contact time: 24 hours
Preventive treatment: 5 g C(M)IT/MIT (3:1) / m3 of water to be
treated.
Category(ies) of users industrial
Pack sizes and packaging material For industrial and professional users:
— HDPE flask: 5 L (nominal)
— HDPE Pail / Jerrycan: 10 L, 20 L, 25 L, 30 L (nominal)
— Box with HDPE liner: 20 L
— HDPE Drum: 110 L, 120 L, 200 L, 260 L
— HDPE IBC: 650 L, 800 L, 1 000 L, 1 250 L
All products should be transport and stored in a vented room.
4.26.1. Use-specific instructions for use
Microbiological tests to prove adequacy of preservation have to be undertaken by the user of C(M)IT/MIT products
in order to determine the effective dose of the preservative for the specific matrix/location/system. If needed,
consult the manufacturer of the preservative product.
4.26.2. Use-specific risk mitigation measures
— Rinse the system (especially the dispensing pumps) with water prior to perform the cleaning step.
— During handling phases (mixing and loading) and cleaning of the dispensing pumps, exposure to the
product (corrosive and skin sensitizer product) has to be limited by use of PPE and application of technical
and organisational RMM:
— Minimisation of manual phases (process automation);
— Use of a dosing device;
— Regular cleaning of equipment and work area;
— Avoidance of contact with contaminated tools and objects;
— Good standard of general ventilation;
— Training and management of staff on good practice.
— PPE is as follows:
— protective chemical resistant gloves (glove material to be specified by the authorisation holder within
the product information);
— protective coverall (at least type 3 or 4, EN 14605) which is impermeable for the biocidal product
shall be worn (coverall material to be specified by the authorisation holder within the product
information);
— Eye protection;
— Substance/task appropriate respirator if ventilation is inadequate.
ELI: http://data.europa.eu/eli/reg_impl/2025/2202/oj 67/227EN
OJ L, 20.11.2025
— The use of C(M)IT/MIT (3:1) containing products for the slimicide treatment in the wet-end stage of the
paper manufacturing process is restricted to
(a) curative treatments in plants connected to a slimicide-free water from a pulp mill and only for the
treatment of the short circulation of the paper mill; and
(b) preventive treatments,
and, for both cases, only if the factory’s waste water is purified in an on-site (full) industrial sewage
treatment plant with a minimal capacity of 5 000 m3per day as described in the Industrial Emission
Directive 2010/75/EU (Best Available Techniques for the production of pulp, paper and board) and if
a dilution of at least 200 times in surface water is achieved after the industrial sewage treatment plant.
4.26.3. Where specific to the use, the particulars of likely direct or indirect effects, first aid instructions and emergency measures to
protect the environment
See general directions for use.
4.26.4. Where specific to the use, the instructions for safe disposal of the product and its packaging
See general directions for use.
4.26.5. Where specific to the use, the conditions of storage and shelf-life of the product under normal conditions of storage
See general directions for use.
4.27. Use description
Table 27
Preventive treatment (biofouling control) online and after cleaning in place for industrial RO/NF
membranes
Product type PT12: Slimicides
Where relevant, an exact description of -
the authorised use
Target organism(s) (including Scientific name: no data
development stage) Common name: Bacteria
Development stage: no data
Field(s) of use indoor use
Preventive treatment (biofouling control) online and after cleaning in
place for industrial RO/NF membranes
Application method(s) Method: closed system
Detailed description:
Manual and automated dosing.Biocidal product application on a
routine basis will prevent biofilm growth on Reverse Osmosis or
Nano Filtration membrane surfaces, feed spacer, filter media and
pipework. The biocidal product should be dispensed to the feed water
at a point to assure adequate mixing throughout the system.
Application rate(s) and frequency Application Rate:
Preventive treatment: 5 g C(M)IT/MIT (3:1) per m3 of fluid
-
68/227 ELI: http://data.europa.eu/eli/reg_impl/2025/2202/ojEN
OJ L, 20.11.2025
Number and timing of application:
Preventive treatment: 5 g C(M)IT/MIT (3:1) per m3 of fluid
Category(ies) of users industrial
Pack sizes and packaging material For industrial and professional users:
— HDPE flask: 5 L (nominal)
— HDPE Pail / Jerrycan: 10 L, 20 L, 25 L, 30 L (nominal)
— Box with HDPE liner: 20 L
— HDPE Drum: 110 L, 120 L, 200 L, 260 L
— HDPE IBC: 650 L, 800 L, 1 000 L, 1 250 L
All products should be transport and stored in a vented room.
4.27.1. Use-specific instructions for use
Microbiological tests to prove adequacy of preservation have to be undertaken by the user of C(M)IT/MIT products
in order to determine the effective dose of the preservative for the specific matrix/location/system. If needed,
consult the manufacturer of the preservative product.
4.27.2. Use-specific risk mitigation measures
— Rinse the system (especially the dispensing pumps) with water prior to perform the cleaning step.
— During handling phases (mixing and loading) and cleaning of the dispensing pumps, exposure to the
product (corrosive and skin sensitizer product) has to be limited by use of PPE and application of technical
and organisational RMM:
— Minimisation of manual phases (process automation);
— Use of a dosing device;
— Regular cleaning of equipment and work area;
— Avoidance of contact with contaminated tools and objects;
— Good standard of general ventilation;
— Training and management of staff on good practice.
— PPE is as follows:
— protective chemical resistant gloves (glove material to be specified by the authorisation holder within
the product information);
— protective coverall (at least type 3 or 4, EN 14605) which is impermeable for the biocidal product
shall be worn (coverall material to be specified by the authorisation holder within the product
information);
— Eye protection;
— Substance/task appropriate respirator if ventilation is inadequate.
— Use product only in premises that are connected to a STP.
4.27.3. Where specific to the use, the particulars of likely direct or indirect effects, first aid instructions and emergency measures to
protect the environment
See general directions for use.
ELI: http://data.europa.eu/eli/reg_impl/2025/2202/oj 69/227EN
OJ L, 20.11.2025
4.27.4. Where specific to the use, the instructions for safe disposal of the product and its packaging
See general directions for use.
4.27.5. Where specific to the use, the conditions of storage and shelf-life of the product under normal conditions of storage
See general directions for use.
4.28. Use description
Table 28
Products to control microbial deterioration in fluids used for working or cutting metal, glass or other
materials
Product type PT13: Working or cutting fluid preservatives
Where relevant, an exact description of -
the authorised use
Target organism(s) (including Scientific name: no data
development stage) Common name: Bacteria
Development stage: no data
Scientific name: no data
Common name: Yeasts
Development stage: no data
Scientific name: no data
Common name: fungi
Development stage: no data
Field(s) of use indoor use
Products to control microbial deterioration in fluids used for working
or cutting metal, glass or other materials
The biocidal product is recommended to control the growth of
bacteria and fungi in fluids used for metalworking fluids (cutting,
grinding, rolling, drawing, etc.) metal surface treatment (aqueous
multipurpose and de-watering rust cleaner fluids, etc.) and cutting
fluids for glass or other materials.
Application method(s) Method: -
Detailed description:
The biocidal product should be dispensed as a tankside additive into
the circulating use-dilution of the fluid, using a metering pump or by
manual pouring, at a point to assure adequate mixing throughout the
system.
Application rate(s) and frequency Application Rate:
Curative treatment: When the system is noticeably fouled, apply
14,9 g C(M)IT/MIT (3:1) per m3 of fluid to be treated. Preventive
treatment: When control is obtained, adding 10 g C(M)IT/MIT (3:1)
per m3 of fluid to be treated.
-
Number and timing of application:
Curative treatment:
When the system is noticeably fouled, apply 14,9 g C(M)IT/MIT (3:1)
per m3 of fluid to be treated.
70/227 ELI: http://data.europa.eu/eli/reg_impl/2025/2202/ojEN
OJ L, 20.11.2025
Contact time: 24h
Preventive treatment:
When control is obtained, adding 10 g C(M)IT/MIT (3:1) per m3 of
fluid to be treated.
Category(ies) of users industrial
Pack sizes and packaging material For industrial and professional users:
— HDPE flask: 5 L (nominal)
— HDPE Pail / Jerrycan: 10 L, 20 L, 25 L, 30 L (nominal)
— Box with HDPE liner: 20 L
— HDPE Drum: 110 L, 120 L, 200 L, 260 L
— HDPE IBC: 650 L, 800 L, 1 000 L, 1 250 L
All products should be transport and stored in a vented room.
4.28.1. Use-specific instructions for use
Microbiological tests to prove adequacy of preservation have to be undertaken by the user of C(M)IT/MIT products
in order to determine the effective dose of the preservative for the specific matrix/location/system. If needed,
consult the manufacturer of the preservative product.
4.28.2. Use-specific risk mitigation measures
— Rinse the system (especially the dispensing pumps) with water prior to perform the cleaning step.
— During handling phases (mixing and loading) and cleaning of the dispensing pumps, exposure to the
product (corrosive and skin sensitizer product) has to be limited by use of PPE and application of technical
and organisational RMM:
— Minimisation of manual phases (process automation);
— Use of a dosing device;
— Regular cleaning of equipment and work area;
— Avoidance of contact with contaminated tools and objects;
— Good standard of general ventilation;
— Training and management of staff on good practice.
— PPE is as follows:
— protective chemical resistant gloves (glove material to be specified by the authorisation holder within
the product information);
— protective coverall (at least type 3 or 4, EN 14605) which is impermeable for the biocidal product
shall be worn (coverall material to be specified by the authorisation holder within the product
information);
— Eye protection;
— Substance/task appropriate respirator if ventilation is inadequate.
4.28.3. Where specific to the use, the particulars of likely direct or indirect effects, first aid instructions and emergency measures to
protect the environment
See general directions for use.
ELI: http://data.europa.eu/eli/reg_impl/2025/2202/oj 71/227EN
OJ L, 20.11.2025
4.28.4. Where specific to the use, the instructions for safe disposal of the product and its packaging
See general directions for use.
4.28.5. Where specific to the use, the conditions of storage and shelf-life of the product under normal conditions of storage
See general directions for use.
5. GENERAL DIRECTIONS FOR USE OF THE META SPC 1
5.1. Instructions for use
— The duration of the effect is dependent on the performance requirements of the customer for their preserved
material and on the specific ingredients composition and pH of the preserved product.
— Always read the label or leaflet before use and follow all the instructions provided.
— Respect the conditions of use of the product (concentration, contact time, temperature, pH, etc.)
PRECAUTIONARY MEASURES DURING STORAGE AND TRANSPORT:
Keep in a well-ventilated place. The product as supplied may evolve gas (largely carbon dioxide) slowly. To prevent
the buildup of pressure the product is packaged in specially vented containers, where necessary. Keep this product
in the original container when not in use. Container must be stored and transported in an upright position to
prevent spilling the contents through the vent, where fitted.
5.2. Risk mitigation measures
-
5.3. Particulars of likely direct or indirect effects, first aid instructions and emergency measures to protect
the environment
— Skin contact: Remove contaminated clothing and shoes. Wash contaminated skin with water. Contact
poison treatment specialist if symptoms occur.
— Eye contact: Immediately flush with plenty of water, occasionally lifting the upper and lower eyelids. Check
for and remove any contact lenses if easy to do. Continue to rinse with tepid water for at least 30 minutes.
Call 112/ambulance for medical assistance.
— Ingestion: Wash out mouth with water. Contact poison treatment specialist. Seek medical advice
immediately if symptoms occur and/or large quantities have been ingested. Do not give fluids or induce
vomiting.
— Inhalation (of spray mist): Remove victim to fresh air and keep at rest in a position comfortable for
breathing. Seek medical advice immediately if symptoms occur and/or large quantities have been inhaled.
— In case of impaired consciousness place in recovery position and seek medical advice immediately.
— Keep the container or label available.
5.4. Instructions for safe disposal of the product and its packaging
— Do not discharge unused product on the ground, into water courses, into pipes (e.g. sink, toilets) nor down
the drains.
— Dispose of unused product, its packaging and all other waste, in accordance with local regulations.
72/227 ELI: http://data.europa.eu/eli/reg_impl/2025/2202/ojEN
OJ L, 20.11.2025
5.5. Conditions of storage and shelf-life of the product under normal conditions of storage
Conditions for safe storage, including any incompatibilities: Keep in a dry, cool and well-ventilated place, in the
original container.
Protect from frost
Shelf-life: 24 months
Protect from sunlight.
Recommendation: If a metal packaging is used, a varnish layer should be applied.
6. OTHER INFORMATION
-
7. THIRD INFORMATION LEVEL: INDIVIDUAL PRODUCTS IN THE META SPC 1
7.1. Trade name(s), authorisation number and specific composition of each individual product
Trade name(s) KATHON™ Market area: EU
WT BIOCIDE
KATHON™ Market area: EU
WT
KATHON™LX Market area: EU
BIOCIDE
KATHON™ Market area: EU
LX
KATHON™ Market area: EU
LX
Microbicide
KATHO­ Market area: EU
N™886MW
BIOCIDE
KATHON™ Market area: EU
886 F
BIOCIDE
Bansan 160 Market area: EU
Biocide Market area: EU
KT1400WT
Biocide Market area: EU
KT1400LX
Biocide Market area: EU
KT1400MW
KT1400MW Market area: EU
ELI: http://data.europa.eu/eli/reg_impl/2025/2202/oj 73/227EN
OJ L, 20.11.2025
KT1400WT Market area: EU
Hydrex™ Market area: EU
7320
MIRECIDE- Market area: EU
KW/650
obbio211 Market area: EU
AQUACIDE C Market area: EU
140
AQUACIDE C Market area: EU
15
AQUACIDE C Market area: EU
21
AQUACIDE C Market area: EU
30
BAC 416 Market area: EU
BIOSTOP 140 Market area: EU
BIOSTOP 15 Market area: EU
BIOSTOP 21 Market area: EU
BIOSTOP 30 Market area: EU
CAT 3693 Market area: EU
GWC 3363 Market area: EU
GWC 3630 Market area: EU
GWE 3693 Market area: EU
IWC Market area: EU
BACTERICIDE
416
Isocil® 14 Market area: EU
France Algue Market area: EU
232
KT1400LX Market area: EU
Authorisation number EU-0025449-0001 1-1
Common name IUPAC name Function CAS number EC number Content (%)
C(M)IT/MIT Reaction mass Active substance 55965-84-9 20,3 % (w/w)
(3:1) of 5-chloro-
2-methyl-2h-
isothiazol-
3-one
and 2-methyl-
2h-isothiazol-
3-one (3:1)
74/227 ELI: http://data.europa.eu/eli/reg_impl/2025/2202/ojEN
OJ L, 20.11.2025
7.2. Trade name(s), authorisation number and specific composition of each individual product
Trade name(s) KATHON™ CF Market area: EU
1400
BIOCIDE
Biocide Market area: EU
KT1400
KT1400 Market area: EU
“hygel“ KW 60 Market area: EU
B ATESTEO
Isocil® Ultra Market area: EU
14
MK3201 Market area: EU
FINEAMIN Market area: EU
Authorisation number EU-0025449-0002 1-1
Common name IUPAC name Function CAS number EC number Content (%)
C(M)IT/MIT Reaction mass Active substance 55965-84-9 20,5 % (w/w)
(3:1) of 5-chloro-
2-methyl-2h-
isothiazol-
3-one
and 2-methyl-
2h-isothiazol-
3-one (3:1)
1. META SPC 2 ADMINISTRATIVE INFORMATION
1.1. Meta SPC 2 identifier
Identifier Meta SPC: meta-SPC 2 KATHON 13-15 Na
1.2. Suffix to the authorisation number
Number 1-2
1.3. Product type(s)
Product type(s) PT06: Preservatives for products during storage
ELI: http://data.europa.eu/eli/reg_impl/2025/2202/oj 75/227EN
OJ L, 20.11.2025
2. META SPC 2 COMPOSITION
2.1. Qualitative and quantitative information on the composition of the meta SPC 2
Common name IUPAC name Function CAS number EC number Content (%)
C(M)IT/MIT (3:1) Reaction mass Active 55965-84-9 18,8 - 20,9 % (w/
of 5-chloro- substance w)
2-methyl-2h-
isothiazol-
3-one
and 2-methyl-
2h-isothiazol-
3-one (3:1)
2.2. Type(s) of formulation of the meta SPC 2
Formulation type(s) AL Any other liquid
3. HAZARD AND PRECAUTIONARY STATEMENTS OF THE META SPC 2
Hazard statements H290: May be corrosive to metals.
H302+H332: Harmful if swallowed or if inhaled.
H311: Toxic in contact with skin.
H314: Causes severe skin burns and eye damage.
H317: May cause an allergic skin reaction.
H410: Very toxic to aquatic life with long lasting effects.
EUH071: Corrosive to the respiratory tract.
Precautionary statements P260: Do not breathe fume.
P264: Wash skin thoroughly after handling.
P270: Do not eat, drink or smoke when using this product.
P271: Use only outdoors or in a well-ventilated area.
P272: Contaminated work clothing should not be allowed
out of the workplace.
P273: Avoid release to the environment.
P280: Wear protective gloves/ protective clothing/ eye
protection/ face protection/ hearing protection .
P330: Rinse mouth.
P302+P352: IF ON SKIN: Wash with plenty of water.
P362+P364: Take off contaminated clothing and wash it
before reuse.
P301+P312: IF SWALLOWED: Call a POISON CENTER or doctor
if you feel unwell.
76/227 ELI: http://data.europa.eu/eli/reg_impl/2025/2202/ojEN
OJ L, 20.11.2025
P333+P313: If skin irritation or rash occurs: Get medical
advice.
P301+P330+P331: IF SWALLOWED: rinse mouth. Do NOT
induce vomiting.
P303+P361+P353: IF ON SKIN (or hair): Take off immediately
all contaminated clothing. Rinse skin with water [or shower].
P304+P340: IF INHALED: Remove person to fresh air and
keep comfortable for breathing.
P310: Immediately call a POISON CENTER/ doctor .
P305+P351+P338: IF IN EYES: Rinse cautiously with water for
several minutes. Remove contact lenses, if present and easy to
do. Continue rinsing.
P391: Collect spillage.
P405: Store locked up.
P234: Keep only in original packaging.
P390: Absorb spillage to prevent material damage.
P406: Store in a corrosion-resistant container with a resistant
inner liner.
4. AUTHORISED USE(S) OF THE META SPC
4.1. Use description
Table 1
Preservation of paints and coatings
Product type PT06: Preservatives for products during storage
Where relevant, an exact description of -
the authorised use
Target organism(s) (including Scientific name: no data
development stage) Common name: Bacteria
Development stage: no data
Scientific name: no data
Common name: Yeasts
Development stage: no data
Field(s) of use indoor use
outdoor use
Preservation of paints and coatings (including electrodeposition)
The biocidal product is recommended to control the growth of
bacteria and yeasts in coatings applied by an electrodeposition
process and associated rinse systems and in water-based paints and
coatings in storage containers before use.
ELI: http://data.europa.eu/eli/reg_impl/2025/2202/oj 77/227EN
OJ L, 20.11.2025
Application method(s) Method: closed system
Detailed description:
Manual and automated dosing. The biocidal product should be
dispensed as a tankside additive into the fluid, using a metering pump
or by manual pouring, at a point to assure adequate mixing
throughout the system.
Application rate(s) and frequency Application Rate:
Industrial uses: 1,5 - 14,5 % C(M)IT/MIT in the biocidal products;
Professional paints and general public paints: 7,5-14,9 mg/kg C(M)
IT/MIT (3:1) in final product.
-
Number and timing of application:
The biocidal product is added at the time of manufacture, storage or
shipment.
Industrial uses:
1,5 - 14,5 % C(M)IT/MIT in the biocidal products.
Professional paints and general public paints:
7,5-14,9 mg/kg C(M)IT/MIT (3:1) in final product.
For the biocidal product as supplied: for industrial use only.
Category(ies) of users industrial
Pack sizes and packaging material For industrial and professional users:
— HDPE flask: 5 L (nominal)
— HDPE Pail / Jerrycan: 10 L, 20 L, 25 L, 30 L (nominal)
— Box with HDPE liner: 20 L
— HDPE Drum: 110 L, 120 L, 200 L, 260 L
— HDPE IBC: 650 L, 800 L, 1 000 L, 1 250 L
All products should be transport and stored in a vented room.
4.1.1. Use-specific instructions for use
— The preservative can be added at any stage of the production of the product.
— Earliest possible addition is recommended for optimal protection.
— Consult the manufacturer to determine the optimal dosage for the various products to be preserved.
— It is recommended that the optimum biocide concentration and compatibility with individual formulations
is determined by means of laboratory tests.
— The duration and storage conditions of the preserved matrices may impact the efficacy of the product,
microbiological tests should be conducted to determine the appropriate application rate without exceeding
the maximum authorised application rate.
— The biocidal product shall be used for treatment of products (articles/mixtures) distributed to professional
users and to the general public.
78/227 ELI: http://data.europa.eu/eli/reg_impl/2025/2202/ojEN
OJ L, 20.11.2025
4.1.2. Use-specific risk mitigation measures
— During handling phases of products from Meta SPC 1, 2, 3 and 4 (Mixing and Loading), exposure to the
product (corrosive and skin sensitizer products) has to be limited by use of PPE and application of technical
and organisational RMM:
— Minimisation of manual phases (process automation);
— Use of a dosing device;
— Regular cleaning of equipment and work area;
— Avoidance of contact with contaminated tools and objects;
— Good standard of general ventilation;
— Training and management of staff on good practice.
— PPE is as follows:
— protective chemical resistant gloves (glove material to be specified by the authorisation holder within
the product information);
— protective coverall (at least type 3 or 4, EN 14605) which is impermeable for the biocidal product
shall be worn (coverall material to be specified by the authorisation holder within the product
information);
— Eye protection;
— Substance/task appropriate respirator if ventilation is inadequate.
— The maximal concentration of products from Meta SPC 1, 2, 3 and 4 to be added in paints used must be
below the threshold value of 15 ppm.
4.1.3. Where specific to the use, the particulars of likely direct or indirect effects, first aid instructions and emergency measures to
protect the environment
See general directions for use.
4.1.4. Where specific to the use, the instructions for safe disposal of the product and its packaging
See general directions for use.
4.1.5. Where specific to the use, the conditions of storage and shelf-life of the product under normal conditions of storage
See general directions for use.
4.2. Use description
Table 2
Preservation of fluids used in paper, textile and leather production - Curative treatment
Product type PT06: Preservatives for products during storage
Where relevant, an exact description of -
the authorised use
Target organism(s) (including Scientific name: no data
development stage) Common name: Bacteria
Development stage: no data
ELI: http://data.europa.eu/eli/reg_impl/2025/2202/oj 79/227EN
OJ L, 20.11.2025
Field(s) of use indoor use
Preservation of fluids used in paper, textile and leather production –
The biocidal product is used to reduce contamination by bacteria in
textile additives (woven and non-woven, natural and synthetic
including silicone emulsions) processing chemicals, all chemicals used
in the leather process industry and paper additives (e.g. water
pigment pastes, starch, natural gums, synthetic and natural latexes,
sizing agents, coating binders, retention aids, dyes, fluorescent
whitening agents, wet-strength resins) used in paper mills. The
biocidal product inhibits the growth microorganisms, which would
otherwise lead to odours formation, viscosity alteration,
discolouration of product and premature product failure.
Application method(s) Method: closed system
Detailed description:
Manual and automated dosing. The biocidal product should be
dispensed to the end use fluid at a point to ensure adequate mixing
using preferably automated metering pump or by manual addition.
Application rate(s) and frequency Application Rate:
Industrial uses: 1,5 - 14,5 % C(M)IT/MIT in the biocidal products;
Professional uses: 16 to 30 mg/kg of C(M)IT/MIT (3:1) in final
product
-
Number and timing of application:
The biocidal product is added at single dose at time of manufacturing,
storage or shipment.
Industrial uses: 1,5 - 14,5 % C(M)IT/MIT in the biocidal products.
Professional uses:
Curative treatment:
16 to 30 mg/kg of C(M)IT/MIT (3:1) in final product
Contact time: 24 hours
For the biocidal product as supplied: for industrial use only.
Category(ies) of users industrial
Pack sizes and packaging material For industrial and professional users:
— HDPE flask: 5 L (nominal)
— HDPE Pail / Jerrycan: 10 L, 20 L, 25 L, 30 L (nominal)
— Box with HDPE liner: 20 L
— HDPE Drum: 110 L, 120 L, 200 L, 260 L
— HDPE IBC: 650 L, 800 L, 1 000 L, 1 250 L
All products should be transport and stored in a vented room.
4.2.1. Use-specific instructions for use
— The preservative can be added at any stage of the production of the product.
— Earliest possible addition is recommended for optimal protection.
— Consult the manufacturer to determine the optimal dosage for the various products to be preserved.
80/227 ELI: http://data.europa.eu/eli/reg_impl/2025/2202/ojEN
OJ L, 20.11.2025
— It is recommended that the optimum biocide concentration and compatibility with individual formulations
is determined by means of laboratory tests.
— The duration and storage conditions of the preserved matrices may impact the efficacy of the product,
microbiological tests should be conducted to determine the appropriate application rate without exceeding
the maximum authorised application rate.
— The biocidal product shall be used for treatment of products (articles/mixtures) distributed only to
professional users.
4.2.2. Use-specific risk mitigation measures
— During handling phases of products from Meta SPC 1, 2, 3 and 4 (mixing and loading), exposure to the
product (corrosive and skin sensitizer products) has to be limited by use of PPE and application of technical
and organisational RMM:
— Minimisation of manual phases (process automation);
— Use of a dosing device;
— Regular cleaning of equipment and work area;
— Avoidance of contact with contaminated tools and objects;
— Good standard of general ventilation;
— Training and management of staff on good practice.
— PPE is as follows:
— protective chemical resistant gloves (glove material to be specified by the authorisation holder within
the product information);
— protective coverall (at least type 3 or 4, EN 14605) which is impermeable for the biocidal product
shall be worn (coverall material to be specified by the authorisation holder within the product
information);
— Eye protection;
— Substance/task appropriate respirator if ventilation is inadequate.
— The maximal products concentration used for the preservation of fluids used in paper, textile and leather
production being above the threshold value of 15 ppm, exposure has to be limited by use of PPE protecting
skin and mucous membranes potentially exposed and application of technical and organisational RMM:
— Minimisation of manual phases;
— Use of a dosing device;
— Regular cleaning of equipment and work area;
— Avoidance of contact with contaminated tools and objects;
— Good standard of general ventilation;
— Training and management of staff on good practice.
4.2.3. Where specific to the use, the particulars of likely direct or indirect effects, first aid instructions and emergency measures to
protect the environment
See general directions for use.
4.2.4. Where specific to the use, the instructions for safe disposal of the product and its packaging
See general directions for use.
ELI: http://data.europa.eu/eli/reg_impl/2025/2202/oj 81/227EN
OJ L, 20.11.2025
4.2.5. Where specific to the use, the conditions of storage and shelf-life of the product under normal conditions of storage
See general directions for use.
4.3. Use description
Table 3
Preservation of glues and adhesives
Product type PT06: Preservatives for products during storage
Where relevant, an exact description of -
the authorised use
Target organism(s) (including Scientific name: no data
development stage) Common name: Bacteria
Development stage: no data
Scientific name: no data
Common name: Yeasts
Development stage: no data
Field(s) of use indoor use
Preservation of glues and adhesives
The biocidal product is recommended to control the growth of
bacteria and yeasts in water-soluble and water-dispersed synthetic and
natural adhesives and tackifiers in storage containers before use
Application method(s) Method: closed system
Detailed description:
Manual and automated application. The biocidal product should be
dispensed to the end use fluid at a point to ensure adequate mixing
using preferably automated metering pump or by manual addition.
Application rate(s) and frequency Application Rate:
Industrial uses: 1,5 - 14,5 % C(M)IT/MIT in the biocidal products;
Professional uses: 8-30 mg/kg C(M)IT/MIT (3:1) in final product.
General public uses: 8-14,9 mg/kg C(M)IT/MIT (3:1) in final product.
-
Number and timing of application:
The biocidal product is added at single dose at the time of
manufacture, storage or shipment.
To ensure uniform distribution, slowly disperse using automated
metering or manual addition, into product with agitation. Mix
thoroughly until evenly dispersed throughout the product.
Industrial uses: 1,5 - 14,5 % C(M)IT/MIT in the biocidal products.
Professional uses:
8-30 mg/kg C(M)IT/MIT (3:1) in final product.
General public uses:
8-14,9 mg/kg C(M)IT/MIT (3:1) in final product.
For the biocidal product as supplied: for industrial use only.
Category(ies) of users industrial
82/227 ELI: http://data.europa.eu/eli/reg_impl/2025/2202/ojEN
OJ L, 20.11.2025
Pack sizes and packaging material For industrial and professional users:
— HDPE flask: 5 L (nominal)
— HDPE Pail / Jerrycan: 10 L, 20 L, 25 L, 30 L (nominal)
— Box with HDPE liner: 20 L
— HDPE Drum: 110 L, 120 L, 200 L, 260 L
— HDPE IBC: 650 L, 800 L, 1 000 L, 1 250 L
All products should be transport and stored in a vented room.
4.3.1. Use-specific instructions for use
— The preservative can be added at any stage of the production of the product.
— Earliest possible addition is recommended for optimal protection.
— Consult the manufacturer to determine the optimal dosage for the various products to be preserved.
— It is recommended that the optimum biocide concentration and compatibility with individual formulations
is determined by means of laboratory tests.
— The duration and storage conditions of the preserved matrices may impact the efficacy of the product,
microbiological tests should be conducted to determine the appropriate application rate without exceeding
the maximum authorised application rate.
— The biocidal product shall be used for treatment of products (articles/mixtures) distributed to professional
users and to the general public. For products distributed to the general public the maximal concentration
used must be below the threshold value of 15 ppm.
4.3.2. Use-specific risk mitigation measures
— During handling phases of products from Meta SPC 1, 2, 3 and 4 (mixing and loading), exposure to the
product (corrosive and skin sensitizer products) has to be limited by use of PPE and application of technical
and organisational RMM:
— Minimisation of manual phases (process automation);
— Use of a dosing device;
— Regular cleaning of equipment and work area;
— Avoidance of contact with contaminated tools and objects;
— Good standard of general ventilation;
— Training and management of staff on good practice.
— PPE is as follows:
— protective chemical resistant gloves (glove material to be specified by the authorisation holder within
the product information);
— protective coverall (at least type 3 or 4, EN 14605) which is impermeable for the biocidal product
shall be worn (coverall material to be specified by the authorisation holder within the product
information);
— Eye protection;
— Substance/task appropriate respirator if ventilation is inadequate.
ELI: http://data.europa.eu/eli/reg_impl/2025/2202/oj 83/227EN
OJ L, 20.11.2025
— For professional users, the maximal products concentration used for the preservation of glues and adhesives
being above the threshold value of 15 ppm, exposure has to be limited by use of PPE, protecting skin and
mucous membranes potentially exposed, and application of technical and organisational RMM:
— Minimisation of manual phases;
— Use of a dosing device;
— Regular cleaning of equipment and work area;
— Good standard of general ventilation;
— Training and management of staff on good practice.
4.3.3. Where specific to the use, the particulars of likely direct or indirect effects, first aid instructions and emergency measures to
protect the environment
See general directions for use.
4.3.4. Where specific to the use, the instructions for safe disposal of the product and its packaging
See general directions for use.
4.3.5. Where specific to the use, the conditions of storage and shelf-life of the product under normal conditions of storage
See general directions for use.
4.4. Use description
Table 4
Preservation of polymer lattices
Product type PT06: Preservatives for products during storage
Where relevant, an exact description of -
the authorised use
Target organism(s) (including Scientific name: no data
development stage) Common name: Bacteria
Development stage: no data
Scientific name: no data
Common name: Yeasts
Development stage: no data
Scientific name: no data
Common name: fungi
Development stage: no data
Field(s) of use indoor use
Preservation of polymer latexes
The biocidal product is recommended for the control of bacteria,
yeast and fungi in the manufacture, storage, and transport of latexes,
synthetic polymers including Hydrolysed Poly Acryl Amide (HPAM)
and biopolymers (e.g. xanthan, dextran..) natural latexes.
Application method(s) Method: closed system
Detailed description:
Manual and automated application. The biocidal product should be
dispensed to the end use fluid at a point to ensure adequate mixing
using preferably automated metering pump or by manual addition.
84/227 ELI: http://data.europa.eu/eli/reg_impl/2025/2202/ojEN
OJ L, 20.11.2025
Application rate(s) and frequency Application Rate:
Industrial uses: 1,5 - 14,5 % C(M)IT/MIT in the biocidal products;
Professional uses: 14,9 - 50 mg /kg of C(M)IT/MIT (3:1) in final
product.
-
Number and timing of application:
The biocidal product is added at single dose at the time of
manufacture, storage or shipment.
To ensure uniform distribution, slowly disperse using automated
metering or manual addition, into product with agitation. Mix
thoroughly until evenly dispersed throughout the product.
Industrial uses: 1,5 - 14,5 % C(M)IT/MIT in the biocidal products.
Professional uses
14,9 - 50 mg /kg of C(M)IT/MIT (3:1) in final product.
For the biocidal product as supplied: for industrial use only.
Category(ies) of users industrial
Pack sizes and packaging material For industrial and professional users:
— HDPE flask: 5 L (nominal)
— HDPE Pail / Jerrycan: 10 L, 20 L, 25 L, 30 L (nominal)
— Box with HDPE liner: 20 L
— HDPE Drum: 110 L, 120 L, 200 L, 260 L
— HDPE IBC: 650 L, 800 L, 1 000 L, 1 250 L
All products should be transport and stored in a vented room.
4.4.1. Use-specific instructions for use
— The preservative can be added at any stage of the production of the product.
— Earliest possible addition is recommended for optimal protection.
— Consult the manufacturer to determine the optimal dosage for the various products to be preserved.
— It is recommended that the optimum biocide concentration and compatibility with individual formulations
is determined by means of laboratory tests.
— The duration and storage conditions of the preserved matrices may impact the efficacy of the product,
microbiological tests should be conducted to determine the appropriate application rate without exceeding
the maximum authorised application rate.
— The biocidal product shall be used for treatment of products (articles/mixtures) distributed only to
professional users.
4.4.2. Use-specific risk mitigation measures
— During handling phases of products from Meta SPC 1, 2, 3 and 4 (mixing and loading), exposure to the
product (corrosive and skin sensitizer products) has to be limited by use of PPE and application of technical
and organisational RMM:
— Minimisation of manual phases (process automation);
— Use of a dosing device;
ELI: http://data.europa.eu/eli/reg_impl/2025/2202/oj 85/227EN
OJ L, 20.11.2025
— Regular cleaning of equipment and work area;
— Avoidance of contact with contaminated tools and objects;
— Good standard of general ventilation;
— Training and management of staff on good practice.
— PPE is as follows:
— protective chemical resistant gloves (glove material to be specified by the authorisation holder within
the product information);
— protective coverall (at least type 3 or 4, EN 14605) which is impermeable for the biocidal product
shall be worn (coverall material to be specified by the authorisation holder within the product
information);
— Eye protection;
— Substance/task appropriate respirator if ventilation is inadequate.
— The maximal products concentration used for the preservation of polymer lattices being above the threshold
value of 15 ppm, exposure has to be limited by use of PPE, protecting skin and mucous membranes
potentially exposed, and application of technical and organisational RMM:
— Minimisation of manual phases;
— Use of a dosing device;
— Regular cleaning of equipment and work area;
— Good standard of general ventilation;
— Training and management of staff on good practice.
4.4.3. Where specific to the use, the particulars of likely direct or indirect effects, first aid instructions and emergency measures to
protect the environment
See general directions for use.
4.4.4. Where specific to the use, the instructions for safe disposal of the product and its packaging
See general directions for use.
4.4.5. Where specific to the use, the conditions of storage and shelf-life of the product under normal conditions of storage
See general directions for use.
4.5. Use description
Table 5
Preservation of mineral slurries
Product type PT06: Preservatives for products during storage
Where relevant, an exact description of -
the authorised use
Target organism(s) (including Scientific name: no data
development stage) Common name: Bacteria
Development stage: no data
86/227 ELI: http://data.europa.eu/eli/reg_impl/2025/2202/ojEN
OJ L, 20.11.2025
Field(s) of use indoor use
Preservation of mineral slurries
The biocidal product is recommended to control the growth of
bacteria in aqueous-based inorganic/mineral slurries and inorganic
pigments which are formulated into paints, coatings and paper.
Application method(s) Method: closed system
Detailed description:
Manual and automated application. The biocidal product should be
dispensed as a tankside additive into the circulating use-dilution of
the fluid, using a metering pump or by manual pouring, at a point to
assure adequate mixing throughout the system.
Application rate(s) and frequency Application Rate:
Industrial uses: 1,5 - 14,5 % C(M)IT/MIT in the biocidal products;
Professional uses: 10- 30 mg/kg of C(M)IT/MIT (3:1) in final product.
-
Number and timing of application:
The biocidal product is added at single dose at the time of
manufacture, storage or shipment.
Industrial uses: 1,5 - 14,5 % C(M)IT/MIT in the biocidal products.
Professional uses:
10- 30 mg/kg of C(M)IT/MIT (3:1) in final product.
For the biocidal product as supplied: for industrial use only.
Category(ies) of users industrial
Pack sizes and packaging material For industrial and professional users:
— HDPE flask: 5 L (nominal)
— HDPE Pail / Jerrycan: 10 L, 20 L, 25 L, 30 L (nominal)
— Box with HDPE liner: 20 L
— HDPE Drum: 110 L, 120 L, 200 L, 260 L
— HDPE IBC: 650 L, 800 L, 1 000 L, 1 250 L
All products should be transport and stored in a vented room.
4.5.1. Use-specific instructions for use
— The preservative can be added at any stage of the production of the product.
— Earliest possible addition is recommended for optimal protection.
— Consult the manufacturer to determine the optimal dosage for the various products to be preserved.
— It is recommended that the optimum biocide concentration and compatibility with individual formulations
is determined by means of laboratory tests.
— The duration and storage conditions of the preserved matrices may impact the efficacy of the product,
microbiological tests should be conducted to determine the appropriate application rate without exceeding
the maximum authorised application rate.
— The biocidal product shall be used for treatment of products (articles/mixtures) distributed only to
professional users.
ELI: http://data.europa.eu/eli/reg_impl/2025/2202/oj 87/227EN
OJ L, 20.11.2025
4.5.2. Use-specific risk mitigation measures
— During handling phases of products from Meta SPC 1, 2, 3 and 4 (mixing and loading), exposure to the
product (corrosive and skin sensitizer products) has to be limited by use of PPE and application of technical
and organisational RMM:
— Minimisation of manual phases (process automation);
— Use of a dosing device;
— Regular cleaning of equipment and work area;
— Avoidance of contact with contaminated tools and objects;
— Good standard of general ventilation;
— Training and management of staff on good practice.
— PPE is as follows:
— protective chemical resistant gloves (glove material to be specified by the authorisation holder within
the product information);
— protective coverall (at least type 3 or 4, EN 14605) which is impermeable for the biocidal product
shall be worn (coverall material to be specified by the authorisation holder within the product
information);
— Eye protection;
— Substance/task appropriate respirator if ventilation is inadequate.
The maximal products concentration used for the preservation of mineral slurries being above the threshold value
of 15 ppm, exposure has to be limited by use of PPE, protecting skin and mucous membranes potentially exposed,
and application of technical and organisational RMM:
— Minimisation of manual phases;
— Use of a dosing device;
— Regular cleaning of equipment and work area;
— Good standard of general ventilation;
— Training and management of staff on good practice.
4.5.3. Where specific to the use, the particulars of likely direct or indirect effects, first aid instructions and emergency measures to
protect the environment
See general directions for use.
4.5.4. Where specific to the use, the instructions for safe disposal of the product and its packaging
See general directions for use.
4.5.5. Where specific to the use, the conditions of storage and shelf-life of the product under normal conditions of storage
See general directions for use.
88/227 ELI: http://data.europa.eu/eli/reg_impl/2025/2202/ojEN
OJ L, 20.11.2025
4.6. Use description
Table 6
Preservation of building products applied indoor only
Product type PT06: Preservatives for products during storage
Where relevant, an exact description of -
the authorised use
Target organism(s) (including Scientific name: no data
development stage) Common name: Bacteria
Development stage: no data
Scientific name: no data
Common name: Yeasts
Development stage: no data
Field(s) of use indoor use
Preservation of building (construction) products (including sealants,
caulks, plasters etc.)
The biocidal product is recommended to control the growth of
bacteria in building (construction) products (sealants, caulks,
biopolymers, plasters, fillers, admixtures concrete additives, joints
compounds,..).
Application method(s) Method: -
Detailed description:
Manual and automated dosing. The biocidal product should be
dispensed to the end use fluid at a point to ensure adequate mixing
using preferably automated metering pump or by manual addition.
Application rate(s) and frequency Application Rate:
Industrial uses: 1,5 - 14,5 % C(M)IT/MIT in the biocidal products;
Professional uses: Add at typical use rate between 16,2-30 mg C(M)
IT/MIT (3:1) per Kg final product to be treated.
-
Number and timing of application:
The biocidal product is added at single dose at the time of
manufacture, storage or shipment.
Slowly dispense using automated metering or manually. Mix
thoroughly until the biocidal product is evenly dispersed.
Industrial uses:
1,5 - 14,5 % C(M)IT/MIT in the biocidal products.
Professional uses:
Add at typical use rate between 16,2-30 mg C(M)IT/MIT (3:1) per Kg
final product to be treated.
For the biocidal product as supplied: for industrial use only.
Category(ies) of users industrial
ELI: http://data.europa.eu/eli/reg_impl/2025/2202/oj 89/227EN
OJ L, 20.11.2025
Pack sizes and packaging material For industrial and professional users:
— HDPE flask: 5 L (nominal)
— HDPE Pail / Jerrycan: 10 L, 20 L, 25 L, 30 L (nominal)
— Box with HDPE liner: 20 L
— HDPE Drum: 110 L, 120 L, 200 L, 260 L
— HDPE IBC: 650 L, 800 L, 1 000 L, 1 250 L
All products should be transport and stored in a vented room.
4.6.1. Use-specific instructions for use
— The preservative can be added at any stage of the production of the product.
— Earliest possible addition is recommended for optimal protection.
— Consult the manufacturer to determine the optimal dosage for the various products to be preserved.
— It is recommended that the optimum biocide concentration and compatibility with individual formulations
is determined by means of laboratory tests.
— The duration and storage conditions of the preserved matrices may impact the efficacy of the product,
microbiological tests should be conducted to determine the appropriate application rate without exceeding
the maximum authorised application rate.
— The biocidal product shall be used for treatment of products (articles/mixtures) distributed only to
professional users.
4.6.2. Use-specific risk mitigation measures
— This use is restricted to the preservation of building material applied indoor only.
— During handling phases for products from Meta SPC 1, 3 and 4 (mixing and loading), exposure to the
product (corrosive and skin sensitizer products) has to be limited by use of PPE and application of technical
and organisational RMM:
— Minimisation of manual phases (process automation);
— Use of a dosing device;
— Regular cleaning of equipment and work area;
— Avoidance of contact with contaminated tools and objects;
— Good standard of general ventilation;
— Training and management of staff on good practice.
— PPE is as follows:
— protective chemical resistant gloves (glove material to be specified by the authorisation holder within
the product information);
— protective coverall (at least type 3 or 4, EN 14605) which is impermeable for the biocidal product
shall be worn (coverall material to be specified by the authorisation holder within the product
information);
— Eye protection;
— Substance/task appropriate respirator if ventilation is inadequate.
90/227 ELI: http://data.europa.eu/eli/reg_impl/2025/2202/ojEN
OJ L, 20.11.2025
For professional users, the maximal products concentration used for the preservation of building products being
above the threshold value of 15 ppm, exposure has to be limited by use of PPE, protecting skin and mucous
membranes potentially exposed, and application of technical and organisational RMM:
— Minimisation of manual phases;
— Regular cleaning of equipment and work area;
— Good standard of general ventilation;
— Training and management of staff on good practice.
4.6.3. Where specific to the use, the particulars of likely direct or indirect effects, first aid instructions and emergency measures to
protect the environment
See general directions for use.
4.6.4. Where specific to the use, the instructions for safe disposal of the product and its packaging
See general directions for use.
4.6.5. Where specific to the use, the conditions of storage and shelf-life of the product under normal conditions of storage
See general directions for use.
4.7. Use description
Table 7
Preservation of inks
Product type PT06: Preservatives for products during storage
Where relevant, an exact description of -
the authorised use
Target organism(s) (including Scientific name: no data
development stage) Common name: Bacteria
Development stage: no data
Scientific name: no data
Common name: Yeasts
Development stage: no data
Field(s) of use indoor use
Preservation of inks
The biocidal product is recommended to control the growth of
bacteria and yeasts in inks and ink components (printing inks
lithographic, photographic, ink-jet fluids, water based dampening or
fountain solutions inks used for textile printing). The biocidal product
inhibits the growth of microorganisms, which would otherwise lead
to odour formation, viscosity alteration, product discolouration and
premature product failure.
Application method(s) Method: closed system
Detailed description:
Manual and automated dosing. The biocidal product should be
dispensed to the end use fluid at a point to ensure adequate mixing
using preferably automated metering pump or by manual addition.
ELI: http://data.europa.eu/eli/reg_impl/2025/2202/oj 91/227EN
OJ L, 20.11.2025
Application rate(s) and frequency Application Rate:
Industrial uses: 1,5 - 14,5 % C(M)IT/MIT in the biocidal products.
Professional uses: 6-30 mg C(M)IT/MIT (3:1) /kg final product.
General public uses: 6-14,9 mg C(M)IT/MIT (3:1) /kg final product.
-
Number and timing of application:
The biocidal product is added at single dose at time of manufacturing,
storage or shipment.
Industrial uses: 1,5 - 14,5 % C(M)IT/MIT in the biocidal products.
Professional uses:
6-30 mg C(M)IT/MIT (3:1) /kg final product.
General public uses:
6-14,9 mg C(M)IT/MIT (3:1) /kg final product.
For the biocidal product as supplied: for industrial use only.
Category(ies) of users industrial
Pack sizes and packaging material For industrial and professional users:
— HDPE flask: 5 L (nominal)
— HDPE Pail / Jerrycan: 10 L, 20 L, 25 L, 30 L (nominal)
— Box with HDPE liner: 20 L
— HDPE Drum: 110 L, 120 L, 200 L, 260 L
— HDPE IBC: 650 L, 800 L, 1 000 L, 1 250 L
All products should be transport and stored in a vented room.
4.7.1. Use-specific instructions for use
— The preservative can be added at any stage of the production of the product.
— Earliest possible addition is recommended for optimal protection.
— Consult the manufacturer to determine the optimal dosage for the various products to be preserved.
— It is recommended that the optimum biocide concentration and compatibility with individual formulations
is determined by means of laboratory tests.
— The duration and storage conditions of the preserved matrices may impact the efficacy of the product,
microbiological tests should be conducted to determine the appropriate application rate without exceeding
the maximum authorised application rate.
— The biocidal product shall be used for treatment of products (articles/mixtures) distributed to professional
users and to the general public. For products distributed to the general public the maximal concentration
used must be below the threshold value of 15 ppm.
4.7.2. Use-specific risk mitigation measures
— During handling phases of products from Meta SPC 1, 2, 3 and 4 (mixing and loading), exposure to the
product (corrosive and skin sensitizer products) has to be limited by use of PPE and application of technical
and organisational RMM:
— Minimisation of manual phases (process automation);
— Use of a dosing device;
92/227 ELI: http://data.europa.eu/eli/reg_impl/2025/2202/ojEN
OJ L, 20.11.2025
— Regular cleaning of equipment and work area;
— Avoidance of contact with contaminated tools and objects;
— Good standard of general ventilation;
— Training and management of staff on good practice.
— PPE is as follows:
— protective chemical resistant gloves (glove material to be specified by the authorisation holder within
the product information);
— protective coverall (at least type 3 or 4, EN 14605) which is impermeable for the biocidal product
shall be worn (coverall material to be specified by the authorisation holder within the product
information);
— Eye protection;
— Substance/task appropriate respirator if ventilation is inadequate.
— For professional users, the maximal products concentration used for the preservation of inks being above
the threshold value of 15 ppm, exposure has to be limited by use of PPE, protecting skin and mucous
membranes potentially exposed, and application of technical and organisational RMM:
— Minimisation of manual phases;
— Use of a dosing device;
— Regular cleaning of equipment and work area;
— Good standard of general ventilation;
— Training and management of staff on good practice.
4.7.3. Where specific to the use, the particulars of likely direct or indirect effects, first aid instructions and emergency measures to
protect the environment
See general directions for use.
4.7.4. Where specific to the use, the instructions for safe disposal of the product and its packaging
See general directions for use.
4.7.5. Where specific to the use, the conditions of storage and shelf-life of the product under normal conditions of storage
See general directions for use.
4.8. Use description
Table 8
Preservation of functional fluids (hydraulic fluids, antifreeze, corrosion inhibitors, etc. - excluding fuel
additives)
Product type PT06: Preservatives for products during storage
Where relevant, an exact description of -
the authorised use
Target organism(s) (including Scientific name: no data
development stage) Common name: Bacteria
Development stage: no data
ELI: http://data.europa.eu/eli/reg_impl/2025/2202/oj 93/227EN
OJ L, 20.11.2025
Field(s) of use indoor use
Preservation of functional fluids (hydraulic fluids, antifreeze,
corrosion inhibitors, etc. - excluding fuel additives)
The biocidal product is recommended to control the growth of
bacteria in functional fluids such as brake and hydraulic fluids,
antifreeze additives, corrosion inhibitors, spinning fluids. The
biocidal product inhibits the growth microorganisms, which would
otherwise lead to odours formation, viscosity alteration,
discolouration of product and premature product failure.
Application method(s) Method: closed system
Detailed description:
Manual and automated dosing. The biocidal product should be
dispensed to the end use fluid at a point to ensure adequate mixing
using preferably automated metering pump or by manual addition.
Application rate(s) and frequency Application Rate:
Industrial uses: 1,5 - 14,5 % C(M)IT/MIT in the biocidal products.
Professional uses: Add at a typical use rate between 6 to 30 mg C(M)
IT/MIT (3:1) per kg final product to be treated.
-
Number and timing of application:
The biocidal product is added at single dose at time of manufacturing,
storage or shipment.
Industrial uses: 1,5 - 14,5 % C(M)IT/MIT in the biocidal products.
Professional uses:
Add at a typical use rate between 6 to 30 mg C(M)IT/MIT (3:1) per kg
final product to be treated
For the biocidal product as supplied: for industrial use only.
Category(ies) of users industrial
Pack sizes and packaging material For industrial and professional users:
— HDPE flask: 5 L (nominal)
— HDPE Pail / Jerrycan: 10 L, 20 L, 25 L, 30 L (nominal)
— Box with HDPE liner: 20 L
— HDPE Drum: 110 L, 120 L, 200 L, 260 L
— HDPE IBC: 650 L, 800 L, 1 000 L, 1 250 L
All products should be transport and stored in a vented room.
4.8.1. Use-specific instructions for use
— The preservative can be added at any stage of the production of the product.
— Earliest possible addition is recommended for optimal protection.
— Consult the manufacturer to determine the optimal dosage for the various products to be preserved.
— It is recommended that the optimum biocide concentration and compatibility with individual formulations
is determined by means of laboratory tests.
94/227 ELI: http://data.europa.eu/eli/reg_impl/2025/2202/ojEN
OJ L, 20.11.2025
— The duration and storage conditions of the preserved matrices may impact the efficacy of the product,
microbiological tests should be conducted to determine the appropriate application rate without exceeding
the maximum authorised application rate.
— The biocidal product shall be used for treatment of products (articles/mixtures) distributed only to
professional users.
4.8.2. Use-specific risk mitigation measures
— During handling phases of products from Meta SPC 1, 2, 3 and 4 (mixing and loading), exposure to the
product (corrosive and skin sensitizer products) has to be limited by use of PPE and application of technical
and organisational RMM:
— Minimisation of manual phases (process automation);
— Use of a dosing device;
— Regular cleaning of equipment and work area;
— Avoidance of contact with contaminated tools and objects;
— Good standard of general ventilation;
— Training and management of staff on good practice.
— PPE is as follows:
— protective chemical resistant gloves (glove material to be specified by the authorisation holder within
the product information);
— protective coverall (at least type 3 or 4, EN 14605) which is impermeable for the biocidal product
shall be worn (coverall material to be specified by the authorisation holder within the product
information);
— Eye protection;
— Substance/task appropriate respirator if ventilation is inadequate.
— The maximal products concentration used for the preservation of functional fluids (hydraulic fluids,
antifreeze, corrosion inhibitors, etc…) being above the threshold value of 15 ppm, exposure has to be
limited by use of PPE, protecting skin and mucous membranes potentially exposed, and application of
technical and organisational RMM:
— Minimisation of manual phases;
— Use of a dosing device;
— Regular cleaning of equipment and work area;
— Good standard of general ventilation;
— Training and management of staff on good practice.
4.8.3. Where specific to the use, the particulars of likely direct or indirect effects, first aid instructions and emergency measures to
protect the environment
See general directions for use.
4.8.4. Where specific to the use, the instructions for safe disposal of the product and its packaging
See general directions for use.
ELI: http://data.europa.eu/eli/reg_impl/2025/2202/oj 95/227EN
OJ L, 20.11.2025
4.8.5. Where specific to the use, the conditions of storage and shelf-life of the product under normal conditions of storage
See general directions for use.
5. GENERAL DIRECTIONS FOR USE OF THE META SPC 2
5.1. Instructions for use
— The duration of the effect is dependent on the performance requirements of the customer for their preserved
material and on the specific ingredients composition and pH of the preserved product.
— Always read the label or leaflet before use and follow all the instructions provided.
— Respect the conditions of use of the product (concentration, contact time, temperature, pH, etc.)
PRECAUTIONARY MEASURES DURING STORAGE AND TRANSPORT:
Keep in a well-ventilated place. The product as supplied may evolve gas (largely carbon dioxide) slowly. To prevent
the buildup of pressure the product is packaged in specially vented containers, where necessary. Keep this product
in the original container when not in use. Container must be stored and transported in an upright position to
prevent spilling the contents through the vent, where fitted.
5.2. Risk mitigation measures
-
5.3. Particulars of likely direct or indirect effects, first aid instructions and emergency measures to protect
the environment
— Skin contact: Remove contaminated clothing and shoes. Wash contaminated skin with water. Contact
poison treatment specialist if symptoms occur.
— Eye contact: Immediately flush with plenty of water, occasionally lifting the upper and lower eyelids. Check
for and remove any contact lenses if easy to do. Continue to rinse with tepid water for at least 30 minutes.
Call 112/ambulance for medical assistance.
— Ingestion: Wash out mouth with water. Contact poison treatment specialist. Seek medical advice
immediately if symptoms occur and/or large quantities have been ingested. Do not give fluids or induce
vomiting.
— Inhalation (of spray mist): Remove victim to fresh air and keep at rest in a position comfortable for
breathing. Seek medical advice immediately if symptoms occur and/or large quantities have been inhaled.
— In case of impaired consciousness place in recovery position and seek medical advice immediately.
— Keep the container or label available.
5.4. Instructions for safe disposal of the product and its packaging
— Do not discharge unused product on the ground, into water courses, into pipes (e.g. sink, toilets) nor down
the drains.
— Dispose of unused product, its packaging and all other waste, in accordance with local regulations.
96/227 ELI: http://data.europa.eu/eli/reg_impl/2025/2202/ojEN
OJ L, 20.11.2025
5.5. Conditions of storage and shelf-life of the product under normal conditions of storage
Conditions for safe storage, including any incompatibilities: Keep in a dry, cool and well-ventilated place, in the
original container.
Protect from frost
Shelf-life: 6 months
Protect from sunlight.
Recommendation: If a metal packaging is used, a varnish layer should be applied.
6. OTHER INFORMATION
-
7. THIRD INFORMATION LEVEL: INDIVIDUAL PRODUCTS IN THE META SPC 2
7.1. Trade name(s), authorisation number and specific composition of each individual product
Trade name(s) KATHON™ Market area: EU
LX 1400
Biocide
KATHON™ Market area: EU
LX 1400
AQUACIDE C Market area: EU
15 P
AQUACIDE C Market area: EU
21 P
AQUACIDE C Market area: EU
30 P
AQUACIDE C Market area: EU
140 P
BAC 416 P Market area: EU
BIOSTOP 140 Market area: EU
P
BIOSTOP 15 P Market area: EU
BIOSTOP 21 P Market area: EU
BIOSTOP 30 P Market area: EU
CAT 3693 P Market area: EU
GWC 3363 P Market area: EU
GWC 3630 P Market area: EU
GWE 3693 P Market area: EU
IWC Market area: EU
BACTERICIDE
416 P
ELI: http://data.europa.eu/eli/reg_impl/2025/2202/oj 97/227EN
OJ L, 20.11.2025
Authorisation number EU-0025449-0003 1-2
Common name IUPAC name Function CAS number EC number Content (%)
C(M)IT/MIT Reaction mass Active substance 55965-84-9 20,5 % (w/w)
(3:1) of 5-chloro-
2-methyl-2h-
isothiazol-
3-one
and 2-methyl-
2h-isothiazol-
3-one (3:1)
1. META SPC 3 ADMINISTRATIVE INFORMATION
1.1. Meta SPC 3 identifier
Identifier Meta SPC: meta-SPC 3 KATHON 1.5-4.5 Mg
1.2. Suffix to the authorisation number
Number 1-3
1.3. Product type(s)
Product type(s) PT02: Disinfectants and algaecides not intended for direct
application to humans or animals
PT04: Food and feed area
PT06: Preservatives for products during storage
PT11: Preservatives for liquid-cooling and processing systems
PT12: Slimicides
PT13: Working or cutting fluid preservatives
2. META SPC 3 COMPOSITION
2.1. Qualitative and quantitative information on the composition of the meta SPC 3
Common name IUPAC name Function CAS number EC number Content (%)
C(M)IT/MIT (3:1) Reaction mass Active 55965-84-9 2,2 - 6,5 % (w/w)
of 5-chloro- substance
2-methyl-2h-
isothiazol-
3-one
and 2-methyl-
2h-isothiazol-
3-one (3:1)
98/227 ELI: http://data.europa.eu/eli/reg_impl/2025/2202/ojEN
OJ L, 20.11.2025
2.2. Type(s) of formulation of the meta SPC 3
Formulation type(s) AL Any other liquid
3. HAZARD AND PRECAUTIONARY STATEMENTS OF THE META SPC 3
Hazard statements H332: Harmful if inhaled.
H314: Causes severe skin burns and eye damage.
H317: May cause an allergic skin reaction.
H410: Very toxic to aquatic life with long lasting effects.
H290: May be corrosive to metals.
H302: Harmful if swallowed.
EUH071: Corrosive to the respiratory tract.
Precautionary statements P260: Do not breathe fume.
P264: Wash skin thoroughly after handling.
P270: Do not eat, drink or smoke when using this product.
P272: Contaminated work clothing should not be allowed
out of the workplace.
P273: Avoid release to the environment.
P280: Wear protective gloves/ protective clothing/ eye
protection/ face protection/ hearing protection .
P362+P364: Take off contaminated clothing and wash it
before reuse.
P333+P313: If skin irritation or rash occurs: Get medical
advice.
P301+P330+P331: IF SWALLOWED: rinse mouth. Do NOT
induce vomiting.
P303+P361+P353: IF ON SKIN (or hair): Take off immediately
all contaminated clothing. Rinse skin with water [or shower].
P304+P340: IF INHALED: Remove person to fresh air and
keep comfortable for breathing.
P310: Immediately call a POISON CENTER/ doctor .
P305+P351+P338: IF IN EYES: Rinse cautiously with water for
several minutes. Remove contact lenses, if present and easy to
do. Continue rinsing.
P391: Collect spillage.
P405: Store locked up.
P234: Keep only in original packaging.
P301+P312: IF SWALLOWED: Call a POISON CENTER/ doctor if
you feel unwell.
P406: Store in a corrosion-resistant container with a resistant
inner liner.
P390: Absorb spillage to prevent material damage.
ELI: http://data.europa.eu/eli/reg_impl/2025/2202/oj 99/227EN
OJ L, 20.11.2025
4. AUTHORISED USE(S) OF THE META SPC
4.1. Use description
Table 1
Preservation of sump water in air conditioning and air washer systems.
Product type PT02: Disinfectants and algaecides not intended for direct application
to humans or animals
Where relevant, an exact description of -
the authorised use
Target organism(s) (including Scientific name: no data
development stage) Common name: Bacteria (including Legionella pneumophila)
Development stage: no data
Scientific name: no data
Common name: Yeasts
Development stage: no data
Scientific name: no data
Common name: fungi
Development stage: no data
Scientific name: no data
Common name: algae
Development stage: no data
Field(s) of use outdoor use
Preservation of sump water in air conditioning and air washer
systems.
Air conditioning systems and in air washer systems to preserve the
sump water. Air washer systems are used extensively in textile
factories and in the tobacco industry to scrub or clean the air and for
fine control of temperature and humidity.
Application method(s) Method: Open and closed Systems
Detailed description:
Automatic and Manual Dosing The biocidal product is typically
added in a central chilled water sump which supplies several air
washers. The loading process may be conducted either manually or
by automation. In the automated process, the biocide is metered
directly into the sump from a holding tank or other type of bulk
container by a dosimeter (pump). The feeding pipe must dose the
biocidal product below the water level in order to limit its
evaporation.
Application rate(s) and frequency Application Rate:
Curative application: Bacteria, yeasts and fungi. When the system is
noticeably fouled, apply 5 to 14,9 mg C(M)IT/MIT (3:1) per Litre of
water to be treated, as post treatment after a shock dose of minimum
0,3 ppm of free chlorine. Preventive application: algae When control
is obtained, add a continuous or semi continuous feed of 3 to 5 mg
C(M)IT/MIT (3:1) per L of water to be treated
-
Number and timing of application:
Curative application: Bacteria, yeasts and fungi
100/227 ELI: http://data.europa.eu/eli/reg_impl/2025/2202/ojEN
OJ L, 20.11.2025
When the system is noticeably fouled, apply 5 to 14,9 mg C(M)
IT/MIT (3:1) per Litre of water to be treated, as post treatment after a
shock dose of minimum 0,3 ppm of free chlorine.
Contact time of 1 hour.
Preventive application: algae
When control is obtained, add a continuous or semi continuous feed
of 3 to 5 mg C(M)IT/MIT (3:1) per L of water to be treated.
Regardless of the manner of treatment, the total concentration of the
active ingredient C(M)IT/MIT (3:1) in the system should not exceed
14,9 mg/L in the sump water.
Preliminary steps prior to addition:
The biocidal product is automatically dosed to the system. Manual
handling is necessary for the loading of the biocidal product into the
dosing systems.
Application Frequency:
Nominally every 2 to 3 days or as needed to obtain control. Repeat
until fouling is reduced to an acceptable level for controlling the
microbial growth.
Category(ies) of users industrial
Pack sizes and packaging material For industrial and professional users:
— HDPE flask: 5 L (nominal)
— HDPE Pail / Jerrycan: 10 L, 20 L, 25 L, 30 L (nominal)
— Box with HDPE liner: 20 L
— HDPE Drum: 110 L, 120 L, 200 L, 260 L
— HDPE IBC: 650 L, 800 L, 1 000 L, 1 250 L
All products should be transport and stored in a vented room.
4.1.1. Use-specific instructions for use
— Respect the conditions of use of the product (concentration, contact time, temperature, pH, etc.).
— The CMIT/MIT biocidal products are used after a shock dose of free chlorine in this application as
standard industry practice.
4.1.2. Use-specific risk mitigation measures
— Rinse the system (especially the dispensing pumps) with water prior to perform the cleaning step.
— During mixing and loading and cleaning of the dispensing pumps, exposure to the product (corrosive and
skin sensitizer product) has to be limited by use of PPE and application of technical and organisational RMM:
— Minimisation of manual phases (process automation);
— Use of a dosing device;
— Regular cleaning of equipment and work area;
— Avoidance of contact with contaminated tools and objects;
— Good standard of general ventilation;
— Training and management of staff on good practice.
ELI: http://data.europa.eu/eli/reg_impl/2025/2202/oj 101/227EN
OJ L, 20.11.2025
— PPE is as follows:
— protective chemical resistant gloves (glove material to be specified by the authorisation holder within
the product information);
— protective coverall (at least type 3 or 4, EN 14605) which is impermeable for the biocidal product
shall be worn (coverall material to be specified by the authorisation holder within the product
information);
— Eye protection;
— Substance/task appropriate respirator if ventilation is inadequate.
4.1.3. Where specific to the use, the particulars of likely direct or indirect effects, first aid instructions and emergency measures to
protect the environment
See general directions for use.
4.1.4. Where specific to the use, the instructions for safe disposal of the product and its packaging
See general directions for use.
4.1.5. Where specific to the use, the conditions of storage and shelf-life of the product under normal conditions of storage
See general directions for use.
4.2. Use description
Table 2
Preservation of fluids in conveyor belts and pasteurisers
Product type PT04: Food and feed area
Where relevant, an exact description of -
the authorised use
Target organism(s) (including Scientific name: no data
development stage) Common name: Bacteria
Development stage: no data
Scientific name: no data
Common name: Yeasts
Development stage: no data
Scientific name: no data
Common name: fungi
Development stage: no data
Field(s) of use indoor use
Preservation of fluids in conveyor belts and pasteurisers
The biocidal product is used for the preservation of process fluids in
pasteurisers and conveyor belts used in food industry. The biocidal
product is used in these systems to either control or kill bacteria and
fungi.
Application method(s) Method: closed system
Detailed description:
Automated dosing The biocidal product is dosed automatically in the
heat transfer fluid, in a place of good mixing (e.g. collecting sump
below the conveyor belt).
102/227 ELI: http://data.europa.eu/eli/reg_impl/2025/2202/ojEN
OJ L, 20.11.2025
Application rate(s) and frequency Application Rate:
Curative application: Bacteria, yeasts and fungi When the system is
noticeably fouled, apply 10 to 14,9 g C(M)IT/MIT (3:1) per m3 of
water to be treated as post treatment after a shock dose of minimum
0,3 ppm of free chlorine Preventive application: Bacteria: When
control is obtained, add a continuous or semi continuous feed of 2,5
to 5 g C(M)IT/MIT (3:1) per m3 of water to be treated.
-
Number and timing of application:
Curative application: Bacteria, yeasts and fungi
When the system is noticeably fouled, apply 10 to 14,9 g C(M)IT/MIT
(3:1) per m3 of water to be treated as post treatment after a shock
dose of minimum 0,3 ppm of free chlorine.
Contact time of 1 hour.
Preventive application: Bacteria:
When control is obtained, add a continuous or semi continuous feed
of 2,5 to 5 g C(M)IT/MIT (3:1) per m3 of water to be treated.
Preliminary steps prior to addition:
The biocidal product is automatically dosed to system. Manual
handling is necessary for the loading of containers containing the
biocidal product into the dosing systems.
Application Frequency:
Nominally every 2 to 3 days or as needed to obtain control. Repeat
until fouling is reduced to an acceptable level for controlling the
microbial growth.
Category(ies) of users industrial
Pack sizes and packaging material For industrial and professional users:
— HDPE flask: 5 L (nominal)
— HDPE Pail / Jerrycan: 10 L, 20 L, 25 L, 30 L (nominal)
— Box with HDPE liner: 20 L
— HDPE Drum: 110 L, 120 L, 200 L, 260 L
— HDPE IBC: 650 L, 800 L, 1 000 L, 1 250 L
All products should be transport and stored in a vented room.
4.2.1. Use-specific instructions for use
— Respect the conditions of use of the product (concentration, contact time, temperature, pH, etc.).
— The CMIT/MIT biocidal products are used after a shock dose of free chlorine in this application as standard
industry practice.
4.2.2. Use-specific risk mitigation measures
— Rinse the system (especially the dispensing pumps) with water prior to perform the cleaning step.
— During mixing and loading and cleaning of the dispensing pumps, exposure to the product (corrosive and
skin sensitizer product) has to be limited by use of PPE and application of technical and organisational RMM:
— Minimisation of manual phases (process automation);
— Use of a dosing device;
ELI: http://data.europa.eu/eli/reg_impl/2025/2202/oj 103/227EN
OJ L, 20.11.2025
— Regular cleaning of equipment and work area;
— Avoidance of contact with contaminated tools and objects;
— Good standard of general ventilation;
— Training and management of staff on good practice.
— PPE is as follows:
— protective chemical resistant gloves (glove material to be specified by the authorisation holder within
the product information);
— protective coverall (at least type 3 or 4, EN 14605) which is impermeable for the biocidal product
shall be worn (coverall material to be specified by the authorisation holder within the product
information);
— Eye protection;
— Substance/task appropriate respirator if ventilation is inadequate.
4.2.3. Where specific to the use, the particulars of likely direct or indirect effects, first aid instructions and emergency measures to
protect the environment
See general directions for use.
4.2.4. Where specific to the use, the instructions for safe disposal of the product and its packaging
See general directions for use.
4.2.5. Where specific to the use, the conditions of storage and shelf-life of the product under normal conditions of storage
See general directions for use.
4.3. Use description
Table 3
Long term offline preservation of reverse osmosis membranes used in potable water
Product type PT04: Food and feed area
Where relevant, an exact description of -
the authorised use
Target organism(s) (including Scientific name: no data
development stage) Common name: Bacteria
Development stage: no data
Field(s) of use indoor use
Long term offline preservation of reverse osmosis membranes used
in potable water
The C(M)IT/MIT (3:1) biocidal product is recommended for
controlling biological growth in off-line trains reverse osmosis
membranes producing potable water for extended periods of time.
104/227 ELI: http://data.europa.eu/eli/reg_impl/2025/2202/ojEN
OJ L, 20.11.2025
Application method(s) Method: closed system
Detailed description:
Manual and automated dosing. It is recommended that fouled
membranes be cleaned prior to shut-down and preservation. Please
refer to RO /NF supplier manual for membrane cleaning and system
shutdown procedures. The biocidal product should be dispensed as a
tankside additive into the circulating use-dilution of the fluid, using a
metering pump or by manual pouring, at a point to assure adequate
mixing throughout the system. After complete filling of the trains
RO/NF systems with the biocide solution, pumps are stopped (Off
line treatment) for extended periods of time. Typically C(M)IT/MIT
(3:1) solutions are prepared in the CIP (cleaning in place) tank and
added via the dosing system. Dilution with the permeate water or
high quality water is recommended for the preparation of the biocide
solution. Membranes should be soaked in the biocide solution during
the shut-down period.
Application rate(s) and frequency Application Rate:
7,5 -20 g of C(M)IT/MIT (3:1)/ m3 of water
-
Number and timing of application:
7,5 -20 g of C(M)IT/MIT (3:1)/ m3 of water
Category(ies) of users industrial
Pack sizes and packaging material For industrial and professional users:
— HDPE flask: 5 L (nominal)
— HDPE Pail / Jerrycan: 10 L, 20 L, 25 L, 30 L (nominal)
— Box with HDPE liner: 20 L
— HDPE Drum: 110 L, 120 L, 200 L, 260 L
— HDPE IBC: 650 L, 800 L, 1 000 L, 1 250 L
All products should be transport and stored in a vented room.
4.3.1. Use-specific instructions for use
— Respect the conditions of use of the product (concentration, contact time, temperature, pH, etc.).
— Prior to taking the membranes back on-line, flush carefully the elements with permeate water in order to
eliminate all the residual biocidal product.
4.3.2. Use-specific risk mitigation measures
— Rinse the system (especially the dispensing pumps) with water prior to perform the cleaning step.
— During mixing and loading and cleaning of the whole system, exposure to the product (corrosive and skin
sensitizer product) has to be limited by use of PPE and application of technical and organisational RMM:
— Minimisation of manual phases (process automation);
— Use of a dosing device;
— Regular cleaning of equipment and work area;
ELI: http://data.europa.eu/eli/reg_impl/2025/2202/oj 105/227EN
OJ L, 20.11.2025
— Avoidance of contact with contaminated tools and objects;
— Good standard of general ventilation;
— Training and management of staff on good practice.
— PPE is as follows:
— protective chemical resistant gloves (glove material to be specified by the authorisation holder within
the product information);
— protective coverall (at least type 3 or 4, EN 14605) which is impermeable for the biocidal product
shall be worn (coverall material to be specified by the authorisation holder within the product
information);
— Eye protection;
— Substance/task appropriate respirator if ventilation is inadequate.
4.3.3. Where specific to the use, the particulars of likely direct or indirect effects, first aid instructions and emergency measures to
protect the environment
See general directions for use.
4.3.4. Where specific to the use, the instructions for safe disposal of the product and its packaging
See general directions for use.
4.3.5. Where specific to the use, the conditions of storage and shelf-life of the product under normal conditions of storage
See general directions for use.
4.4. Use description
Table 4
Preservation of paints and coatings
Product type PT06: Preservatives for products during storage
Where relevant, an exact description of -
the authorised use
Target organism(s) (including Scientific name: no data
development stage) Common name: Bacteria
Development stage: no data
Scientific name: no data
Common name: Yeasts
Development stage: no data
Field(s) of use indoor use
outdoor use
Preservation of paints and coatings
(including electrodeposition)
The biocidal product is recommended to control the growth of
bacteria and yeasts in coatings applied by an electrodeposition
process and associated rinse systems and in water-based paints and
coatings in storage containers before use.
106/227 ELI: http://data.europa.eu/eli/reg_impl/2025/2202/ojEN
OJ L, 20.11.2025
Application method(s) Method: closed system
Detailed description:
Manual and automated dosing. The biocidal product should be
dispensed as a tankside additive into the fluid, using a metering pump
or by manual pouring, at a point to assure adequate mixing
throughout the system.
Application rate(s) and frequency Application Rate:
Industrial uses: 1,5 - 14,5 % C(M)IT/MIT in the biocidal products;
Professional paints and general public paints: 7,5-14,9 mg/kg C(M)
IT/MIT (3:1) in final product.
-
Number and timing of application:
The biocidal product is added at the time of manufacture, storage or
shipment.
Industrial uses:
1,5 - 14,5 % C(M)IT/MIT in the biocidal products.
Professional paints and general public paints:
7,5-14,9 mg/kg C(M)IT/MIT (3:1) in final product.
For the biocidal product as supplied: for industrial use only.
Category(ies) of users industrial
Pack sizes and packaging material For industrial and professional users:
— HDPE flask: 5 L (nominal)
— HDPE Pail / Jerrycan: 10 L, 20 L, 25 L, 30 L (nominal)
— Box with HDPE liner: 20 L
— HDPE Drum: 110 L, 120 L, 200 L, 260 L
— HDPE IBC: 650 L, 800 L, 1 000 L, 1 250 L
All products should be transport and stored in a vented room.
4.4.1. Use-specific instructions for use
— The preservative can be added at any stage of the production of the product.
— Earliest possible addition is recommended for optimal protection.
— Consult the manufacturer to determine the optimal dosage for the various products to be preserved.
— It is recommended that the optimum biocide concentration and compatibility with individual formulations
is determined by means of laboratory tests.
— The duration and storage conditions of the preserved matrices may impact the efficacy of the product,
microbiological tests should be conducted to determine the appropriate application rate without exceeding
the maximum authorised application rate.
— The biocidal product shall be used for treatment of products (articles/mixtures) distributed to professional
users and to the general public.
ELI: http://data.europa.eu/eli/reg_impl/2025/2202/oj 107/227EN
OJ L, 20.11.2025
4.4.2. Use-specific risk mitigation measures
— During handling phases of products from Meta SPC 1, 2, 3 and 4 (Mixing and Loading), exposure to the
product (corrosive and skin sensitizer products) has to be limited by use of PPE and application of technical
and organisational RMM:
— Minimisation of manual phases (process automation);
— Use of a dosing device;
— Regular cleaning of equipment and work area;
— Avoidance of contact with contaminated tools and objects;
— Good standard of general ventilation;
— Training and management of staff on good practice.
— PPE is as follows:
— protective chemical resistant gloves (glove material to be specified by the authorisation holder within
the product information);
— protective coverall (at least type 3 or 4, EN 14605) which is impermeable for the biocidal product
shall be worn (coverall material to be specified by the authorisation holder within the product
information);
— Eye protection;
— Substance/task appropriate respirator if ventilation is inadequate.
— The maximal concentration of products from Meta SPC 1, 2, 3 and 4 to be added in paints used must be
below the threshold value of 15 ppm.
4.4.3. Where specific to the use, the particulars of likely direct or indirect effects, first aid instructions and emergency measures to
protect the environment
See general directions for use.
4.4.4. Where specific to the use, the instructions for safe disposal of the product and its packaging
See general directions for use.
4.4.5. Where specific to the use, the conditions of storage and shelf-life of the product under normal conditions of storage
See general directions for use.
4.5. Use description
Table 5
Preservation of detergents and household products
Product type PT06: Preservatives for products during storage
Where relevant, an exact description of -
the authorised use
Target organism(s) (including Scientific name: no data
development stage) Common name: Bacteria
Development stage: no data
Scientific name: no data
Common name: Yeasts
Development stage: no data
108/227 ELI: http://data.europa.eu/eli/reg_impl/2025/2202/ojEN
OJ L, 20.11.2025
Scientific name: no data
Common name: fungi
Development stage: no data
Field(s) of use indoor use
Preservation of detergents (washing and cleaning fluids) and
household products.
The biocidal product is recommended for the control of bacteria,
yeast and fungi in detergents and cleaning fluids (i.e. hard surface
cleaners (all-purpose cleaners), hand dish washing products, fabric
softeners, laundry detergents), products used for car care, floor care,
waxes, hard surface cleaners, pre-moistened sponges or mops, and
the surfactants used in these types of products.
Application method(s) Method: closed system
Detailed description:
Manual and automated application. The biocidal product should be
dispensed to the end use fluid at a point to ensure adequate mixing
using preferably automated metering pump or by manual addition.
Application rate(s) and frequency Application Rate:
Industrial uses: 1,5 - 14,5 % C(M)IT/MIT in the biocidal products;
Professional and general public uses: 6-14,9 mg/kg C(M)IT/MIT (3:1)
in final product.
-
Number and timing of application:
The biocidal product is added at single dose at the time of
manufacturing, storage or shipment.
To ensure uniform distribution, slowly disperse using automated
metering or manual addition, into product with agitation. Mix
thoroughly until evenly dispersed throughout the product.
Institutional and Household products:
(detergents, cleaners, softeners, etc.)
Industrial uses:
1,5 - 14,5 % C(M)IT/MIT in the biocidal products.
Professional and general public uses:
6-14,9 mg/kg C(M)IT/MIT (3:1) in final product.
For the biocidal product as supplied: for industrial use only.
Category(ies) of users industrial
Pack sizes and packaging material For industrial and professional users:
— HDPE flask: 5 L (nominal)
— HDPE Pail / Jerrycan: 10 L, 20 L, 25 L, 30 L (nominal)
— Box with HDPE liner: 20 L
— HDPE Drum: 110 L, 120 L, 200 L, 260 L
— HDPE IBC: 650 L, 800 L, 1 000 L, 1 250 L
All products should be transport and stored in a vented room.
4.5.1. Use-specific instructions for use
— The preservative can be added at any stage of the production of the product.
— Earliest possible addition is recommended for optimal protection.
ELI: http://data.europa.eu/eli/reg_impl/2025/2202/oj 109/227EN
OJ L, 20.11.2025
— Consult the manufacturer to determine the optimal dosage for the various products to be preserved.
— It is recommended that the optimum biocide concentration and compatibility with individual formulations
is determined by means of laboratory tests.
— The duration and storage conditions of the preserved matrices may impact the efficacy of the product,
microbiological tests should be conducted to determine the appropriate application rate without exceeding
the maximum authorised application rate.
— The biocidal product shall be used for treatment of products (articles/mixtures) distributed to professional
users and to the general public.
4.5.2. Use-specific risk mitigation measures
— During handling phases of products from Meta SPC 1 and 3 (mixing and loading), exposure to the product
(corrosive and skin sensitizer products) has to be limited by use of PPE and application of technical and
organisational RMM:
— Minimisation of manual phases (process automation);
— Use of a dosing device;
— Regular cleaning of equipment and work area;
— Avoidance of contact with contaminated tools and objects;
— Good standard of general ventilation;
— Training and management of staff on good practice.
— PPE is as follows:
— protective chemical resistant gloves (glove material to be specified by the authorisation holder within
the product information);
— protective coverall (at least type 3 or 4, EN 14605) which is impermeable for the biocidal product
shall be worn (coverall material to be specified by the authorisation holder within the product
information);
— Eye protection;
— Substance/task appropriate respirator if ventilation is inadequate.
— The maximal concentration of products from Meta SPC 1 and 3 to be added in detergents and household
products used must be below the threshold value of 15 ppm.
4.5.3. Where specific to the use, the particulars of likely direct or indirect effects, first aid instructions and emergency measures to
protect the environment
See general directions for use.
4.5.4. Where specific to the use, the instructions for safe disposal of the product and its packaging
See general directions for use.
4.5.5. Where specific to the use, the conditions of storage and shelf-life of the product under normal conditions of storage
See general directions for use.
110/227 ELI: http://data.europa.eu/eli/reg_impl/2025/2202/ojEN
OJ L, 20.11.2025
4.6. Use description
Table 6
Preservation of fluids used in paper, textile and leather production - Curative treatment
Product type PT06: Preservatives for products during storage
Where relevant, an exact description of -
the authorised use
Target organism(s) (including Scientific name: no data
development stage) Common name: Bacteria
Development stage: no data
Field(s) of use indoor use
Preservation of fluids used in paper, textile and leather production -
The biocidal product is used to reduce contamination by bacteria in
textile additives (woven and non-woven, natural and synthetic
including silicone emulsions) processing chemicals, all chemicals used
in the leather process industry and paper additives (e.g. water
pigment pastes, starch, natural gums, synthetic and natural latexes,
sizing agents, coating binders, retention aids, dyes, fluorescent
whitening agents, wet-strength resins) used in paper mills. The
biocidal product inhibits the growth microorganisms, which would
otherwise lead to odours formation, viscosity alteration,
discolouration of product and premature product failure.
Application method(s) Method: closed system
Detailed description:
Manual and automated dosing. The biocidal product should be
dispensed to the end use fluid at a point to ensure adequate mixing
using preferably automated metering pump or by manual addition.
Application rate(s) and frequency Application Rate:
Industrial uses: 1,5 - 14,5 % C(M)IT/MIT in the biocidal products;
Professional uses: 16 to 30 mg/kg of C(M)IT/MIT (3:1) in final
product
-
Number and timing of application:
The biocidal product is added at single dose at time of manufacturing,
storage or shipment.
Industrial uses: 1,5 - 14,5 % C(M)IT/MIT in the biocidal products.
Professional uses:
Curative treatment:
16 to 30 mg/kg of C(M)IT/MIT (3:1) in final product
Contact time: 24 hours
For the biocidal product as supplied: for industrial use only.
Category(ies) of users industrial
Pack sizes and packaging material For industrial and professional users:
— HDPE flask: 5 L (nominal)
— HDPE Pail / Jerrycan: 10 L, 20 L, 25 L, 30 L (nominal)
ELI: http://data.europa.eu/eli/reg_impl/2025/2202/oj 111/227EN
OJ L, 20.11.2025
— Box with HDPE liner: 20 L
— HDPE Drum: 110 L, 120 L, 200 L, 260 L
— HDPE IBC: 650 L, 800 L, 1 000 L, 1 250 L
All products should be transport and stored in a vented room.
4.6.1. Use-specific instructions for use
— The preservative can be added at any stage of the production of the product.
— Earliest possible addition is recommended for optimal protection.
— Consult the manufacturer to determine the optimal dosage for the various products to be preserved.
— It is recommended that the optimum biocide concentration and compatibility with individual formulations
is determined by means of laboratory tests.
— The duration and storage conditions of the preserved matrices may impact the efficacy of the product,
microbiological tests should be conducted to determine the appropriate application rate without exceeding
the maximum authorised application rate.
— The biocidal product shall be used for treatment of products (articles/mixtures) distributed only to
professional users.
4.6.2. Use-specific risk mitigation measures
— During handling phases of products from Meta SPC 1, 2, 3 and 4 (mixing and loading), exposure to the
product (corrosive and skin sensitizer products) has to be limited by use of PPE and application of technical
and organisational RMM:
— Minimisation of manual phases (process automation);
— Use of a dosing device;
— Regular cleaning of equipment and work area;
— Avoidance of contact with contaminated tools and objects;
— Good standard of general ventilation;
— Training and management of staff on good practice.
— PPE is as follows:
— protective chemical resistant gloves (glove material to be specified by the authorisation holder within
the product information);
— protective coverall (at least type 3 or 4, EN 14605) which is impermeable for the biocidal product
shall be worn (coverall material to be specified by the authorisation holder within the product
information);
— Eye protection;
— Substance/task appropriate respirator if ventilation is inadequate.
— The maximal products concentration used for the preservation of fluids used in paper, textile and leather
production being above the threshold value of 15 ppm, exposure has to be limited by use of PPE protecting
skin and mucous membranes potentially exposed and application of technical and organisational RMM:
— Minimisation of manual phases;
— Use of a dosing device;
112/227 ELI: http://data.europa.eu/eli/reg_impl/2025/2202/ojEN
OJ L, 20.11.2025
— Regular cleaning of equipment and work area;
— Avoidance of contact with contaminated tools and objects;
— Good standard of general ventilation;
— Training and management of staff on good practice.
4.6.3. Where specific to the use, the particulars of likely direct or indirect effects, first aid instructions and emergency measures to
protect the environment
See general directions for use.
4.6.4. Where specific to the use, the instructions for safe disposal of the product and its packaging
See general directions for use.
4.6.5. Where specific to the use, the conditions of storage and shelf-life of the product under normal conditions of storage
See general directions for use.
4.7. Use description
Table 7
Preservation of glues and adhesives
Product type PT06: Preservatives for products during storage
Where relevant, an exact description of -
the authorised use
Target organism(s) (including Scientific name: no data
development stage) Common name: Bacteria
Development stage: no data
Scientific name: no data
Common name: Yeasts
Development stage: no data
Field(s) of use indoor use
Preservation of glues and adhesives
The biocidal product is recommended to control the growth of
bacteria and yeasts in water-soluble and water-dispersed synthetic and
natural adhesives and tackifiers in storage containers before use
Application method(s) Method: closed system
Detailed description:
Manual and automated application. The biocidal product should be
dispensed to the end use fluid at a point to ensure adequate mixing
using preferably automated metering pump or by manual addition.
Application rate(s) and frequency Application Rate:
Industrial uses: 1,5 - 14,5 % C(M)IT/MIT in the biocidal products;
Professional uses: 8-30 mg/kg C(M)IT/MIT (3:1) in final product.
General public uses: 8-14,9 mg/kg C(M)IT/MIT (3:1) in final product.
-
Number and timing of application:
The biocidal product is added at single dose at the time of
manufacture, storage or shipment.
ELI: http://data.europa.eu/eli/reg_impl/2025/2202/oj 113/227EN
OJ L, 20.11.2025
To ensure uniform distribution, slowly disperse using automated
metering or manual addition, into product with agitation. Mix
thoroughly until evenly dispersed throughout the product.
Industrial uses: 1,5 - 14,5 % C(M)IT/MIT in the biocidal products.
Professional uses:
8-30 mg/kg C(M)IT/MIT (3:1) in final product.
General public uses:
8-14,9 mg/kg C(M)IT/MIT (3:1) in final product.
For the biocidal product as supplied: for industrial use only.
Category(ies) of users industrial
Pack sizes and packaging material For industrial and professional users:
— HDPE flask: 5 L (nominal)
— HDPE Pail / Jerrycan: 10 L, 20 L, 25 L, 30 L (nominal)
— Box with HDPE liner: 20 L
— HDPE Drum: 110 L, 120 L, 200 L, 260 L
— HDPE IBC: 650 L, 800 L, 1 000 L, 1 250 L
All products should be transport and stored in a vented room.
4.7.1. Use-specific instructions for use
— The preservative can be added at any stage of the production of the product.
— Earliest possible addition is recommended for optimal protection.
— Consult the manufacturer to determine the optimal dosage for the various products to be preserved.
— It is recommended that the optimum biocide concentration and compatibility with individual formulations
is determined by means of laboratory tests.
— The duration and storage conditions of the preserved matrices may impact the efficacy of the product,
microbiological tests should be conducted to determine the appropriate application rate without exceeding
the maximum authorised application rate.
— The biocidal product shall be used for treatment of products (articles/mixtures) distributed to professional
users and to the general public. For products distributed to the general public the maximal concentration
used must be below the threshold value of 15 ppm.
4.7.2. Use-specific risk mitigation measures
— During handling phases of products from Meta SPC 1, 2, 3 and 4 (mixing and loading), exposure to the
product (corrosive and skin sensitizer products) has to be limited by use of PPE and application of technical
and organisational RMM:
— Minimisation of manual phases (process automation);
— Use of a dosing device;
— Regular cleaning of equipment and work area;
— Avoidance of contact with contaminated tools and objects;
— Good standard of general ventilation;
— Training and management of staff on good practice.
114/227 ELI: http://data.europa.eu/eli/reg_impl/2025/2202/ojEN
OJ L, 20.11.2025
— PPE is as follows:
— protective chemical resistant gloves (glove material to be specified by the authorisation holder within
the product information);
— protective coverall (at least type 3 or 4, EN 14605) which is impermeable for the biocidal product
shall be worn (coverall material to be specified by the authorisation holder within the product
information);
— Eye protection;
— Substance/task appropriate respirator if ventilation is inadequate.
— For professional users, the maximal products concentration used for the preservation of glues and adhesives
being above the threshold value of 15 ppm, exposure has to be limited by use of PPE, protecting skin and
mucous membranes potentially exposed, and application of technical and organisational RMM:
— Minimisation of manual phases;
— Use of a dosing device;
— Regular cleaning of equipment and work area;
— Good standard of general ventilation;
— Training and management of staff on good practice.
4.7.3. Where specific to the use, the particulars of likely direct or indirect effects, first aid instructions and emergency measures to
protect the environment
See general directions for use.
4.7.4. Where specific to the use, the instructions for safe disposal of the product and its packaging
See general directions for use.
4.7.5. Where specific to the use, the conditions of storage and shelf-life of the product under normal conditions of storage
See general directions for use.
4.8. Use description
Table 8
Preservation of polymer lattices
Product type PT06: Preservatives for products during storage
Where relevant, an exact description of -
the authorised use
Target organism(s) (including Scientific name: no data
development stage) Common name: Bacteria
Development stage: no data
Scientific name: no data
Common name: Yeasts
Development stage: no data
Scientific name: no data
Common name: fungi
Development stage: no data
ELI: http://data.europa.eu/eli/reg_impl/2025/2202/oj 115/227EN
OJ L, 20.11.2025
Field(s) of use indoor use
Preservation of polymer latexes
The biocidal product is recommended for the control of bacteria,
yeast and fungi in the manufacture, storage, and transport of latexes,
synthetic polymers including Hydrolysed Poly Acryl Amide (HPAM)
and biopolymers (e.g. xanthan, dextran..) natural latexes.
Application method(s) Method: closed system
Detailed description:
Manual and automated application. The biocidal product should be
dispensed to the end use fluid at a point to ensure adequate mixing
using preferably automated metering pump or by manual addition.
Application rate(s) and frequency Application Rate:
Industrial uses: 1,5 - 14,5 % C(M)IT/MIT in the biocidal products;
Professional uses: 14,9 - 50 mg /kg of C(M)IT/MIT (3:1) in final
product.
-
Number and timing of application:
The biocidal product is added at single dose at the time of
manufacture, storage or shipment.
To ensure uniform distribution, slowly disperse using automated
metering or manual addition, into product with agitation. Mix
thoroughly until evenly dispersed throughout the product.
Industrial uses: 1,5 - 14,5 % C(M)IT/MIT in the biocidal products.
Professional uses
14,9 - 50 mg /kg of C(M)IT/MIT (3:1) in final product.
For the biocidal product as supplied: for industrial use only.
Category(ies) of users industrial
Pack sizes and packaging material For industrial and professional users:
— HDPE flask: 5 L (nominal)
— HDPE Pail / Jerrycan: 10 L, 20 L, 25 L, 30 L (nominal)
— Box with HDPE liner: 20 L
— HDPE Drum: 110 L, 120 L, 200 L, 260 L
— HDPE IBC: 650 L, 800 L, 1 000 L, 1 250 L
All products should be transport and stored in a vented room.
4.8.1. Use-specific instructions for use
— The preservative can be added at any stage of the production of the product.
— Earliest possible addition is recommended for optimal protection.
— Consult the manufacturer to determine the optimal dosage for the various products to be preserved.
— It is recommended that the optimum biocide concentration and compatibility with individual formulations
is determined by means of laboratory tests.
116/227 ELI: http://data.europa.eu/eli/reg_impl/2025/2202/ojEN
OJ L, 20.11.2025
— The duration and storage conditions of the preserved matrices may impact the efficacy of the product,
microbiological tests should be conducted to determine the appropriate application rate without exceeding
the maximum authorised application rate.
— The biocidal product shall be used for treatment of products (articles/mixtures) distributed only to
professional users.
4.8.2. Use-specific risk mitigation measures
— During handling phases of products from Meta SPC 1, 2, 3 and 4 (mixing and loading), exposure to the
product (corrosive and skin sensitizer products) has to be limited by use of PPE and application of technical
and organisational RMM:
— Minimisation of manual phases (process automation);
— Use of a dosing device;
— Regular cleaning of equipment and work area;
— Avoidance of contact with contaminated tools and objects;
— Good standard of general ventilation;
— Training and management of staff on good practice.
— PPE is as follows:
— protective chemical resistant gloves (glove material to be specified by the authorisation holder within
the product information);
— protective coverall (at least type 3 or 4, EN 14605) which is impermeable for the biocidal product
shall be worn (coverall material to be specified by the authorisation holder within the product
information);
— Eye protection;
— Substance/task appropriate respirator if ventilation is inadequate.
— The maximal products concentration used for the preservation of polymer lattices being above the threshold
value of 15 ppm, exposure has to be limited by use of PPE, protecting skin and mucous membranes
potentially exposed, and application of technical and organisational RMM:
— Minimisation of manual phases;
— Use of a dosing device;
— Regular cleaning of equipment and work area;
— Good standard of general ventilation;
— Training and management of staff on good practice.
4.8.3. Where specific to the use, the particulars of likely direct or indirect effects, first aid instructions and emergency measures to
protect the environment
See general directions for use.
4.8.4. Where specific to the use, the instructions for safe disposal of the product and its packaging
See general directions for use.
4.8.5. Where specific to the use, the conditions of storage and shelf-life of the product under normal conditions of storage
See general directions for use.
ELI: http://data.europa.eu/eli/reg_impl/2025/2202/oj 117/227EN
OJ L, 20.11.2025
4.9. Use description
Table 9
Preservation of biocides and fertilizers
Product type PT06: Preservatives for products during storage
Where relevant, an exact description of -
the authorised use
Target organism(s) (including Scientific name: no data
development stage) Common name: Bacteria
Development stage: no data
Scientific name: no data
Common name: Yeasts
Development stage: no data
Field(s) of use indoor use
outdoor use
Preservation of biocides and fertilizers
The biocidal product is recommended to control the growth of
bacteria and yeasts in fertilizers and biocidal products.
Application method(s) Method: -
Detailed description:
Manual and automated application. The biocidal product should be
dispensed to the end use fluid at a point to ensure adequate mixing
using preferably automated metering pump or by manual addition.
Application rate(s) and frequency Application Rate:
Industrial uses: 1,5 - 14,5 % C(M)IT/MIT in the biocidal products;
Professional uses: 10- 30 mg/kg of C(M)IT/MIT (3:1) in final product.
-
Number and timing of application:
The biocidal product is added at single dose at the time of
manufacture, storage or shipment.
Industrial uses: 1,5 - 14,5 % C(M)IT/MIT in the biocidal products.
Professional uses:
10- 30 mg/kg of C(M)IT/MIT (3:1) in final product.
For the biocidal product as supplied: for industrial use only.
Category(ies) of users industrial
Pack sizes and packaging material For industrial and professional users:
— HDPE flask: 5 L (nominal)
— HDPE Pail / Jerrycan: 10 L, 20 L, 25 L, 30 L (nominal)
— Box with HDPE liner: 20 L
— HDPE Drum: 110 L, 120 L, 200 L, 260 L
— HDPE IBC: 650 L, 800 L, 1 000 L, 1 250 L
All products should be transport and stored in a vented room.
118/227 ELI: http://data.europa.eu/eli/reg_impl/2025/2202/ojEN
OJ L, 20.11.2025
4.9.1. Use-specific instructions for use
— The preservative can be added at any stage of the production of the product.
— Earliest possible addition is recommended for optimal protection.
— Consult the manufacturer to determine the optimal dosage for the various products to be preserved.
— It is recommended that the optimum biocide concentration and compatibility with individual formulations
is determined by means of laboratory tests.
— The duration and storage conditions of the preserved matrices may impact the efficacy of the product,
microbiological tests should be conducted to determine the appropriate application rate without exceeding
the maximum authorised application rate.
— The biocidal product shall be used for treatment of products (articles/mixtures) distributed only to
professional users.
4.9.2. Use-specific risk mitigation measures
— During handling phases of products from Meta SPC 1 and 3 (mixing and loading), exposure to the product
(corrosive and skin sensitizer products) has to be limited by use of PPE and application of technical and
organisational RMM:
— Minimisation of manual phases (process automation);
— Use of a dosing device;
— Regular cleaning of equipment and work area;
— Avoidance of contact with contaminated tools and objects;
— Good standard of general ventilation;
— Training and management of staff on good practice.
— PPE is as follows:
— protective chemical resistant gloves (glove material to be specified by the authorisation holder within
the product information);
— protective coverall (at least type 3 or 4, EN 14605) which is impermeable for the biocidal product
shall be worn (coverall material to be specified by the authorisation holder within the product
information);
— Eye protection;
— Substance/task appropriate respirator if ventilation is inadequate.
— For professional users, the maximal products concentration used for the preservation of biocides and
fertilizers being above the threshold value of 15 ppm, exposure has to be limited by use of PPE, protecting
skin and mucous membranes potentially exposed, and application of technical and organisational RMM:
— Minimisation of manual phases;
— Use of a dosing device;
— Regular cleaning of equipment and work area;
— Good standard of general ventilation;
— Training and management of staff on good practice.
ELI: http://data.europa.eu/eli/reg_impl/2025/2202/oj 119/227EN
OJ L, 20.11.2025
4.9.3. Where specific to the use, the particulars of likely direct or indirect effects, first aid instructions and emergency measures to
protect the environment
See general directions for use.
4.9.4. Where specific to the use, the instructions for safe disposal of the product and its packaging
See general directions for use.
4.9.5. Where specific to the use, the conditions of storage and shelf-life of the product under normal conditions of storage
See general directions for use.
4.10. Use description
Table 10
Preservation of mineral slurries
Product type PT06: Preservatives for products during storage
Where relevant, an exact description of -
the authorised use
Target organism(s) (including Scientific name: no data
development stage) Common name: Bacteria
Development stage: no data
Field(s) of use indoor use
Preservation of mineral slurries
The biocidal product is recommended to control the growth of
bacteria in aqueous-based inorganic/mineral slurries and inorganic
pigments which are formulated into paints, coatings and paper.
Application method(s) Method: closed system
Detailed description:
Manual and automated application. The biocidal product should be
dispensed as a tankside additive into the circulating use-dilution of
the fluid, using a metering pump or by manual pouring, at a point to
assure adequate mixing throughout the system.
Application rate(s) and frequency Application Rate:
Industrial uses: 1,5 - 14,5 % C(M)IT/MIT in the biocidal products;
Professional uses: 10- 30 mg/kg of C(M)IT/MIT (3:1) in final product.
-
Number and timing of application:
The biocidal product is added at single dose at the time of
manufacture, storage or shipment.
Industrial uses: 1,5 - 14,5 % C(M)IT/MIT in the biocidal products.
Professional uses:
10- 30 mg/kg of C(M)IT/MIT (3:1) in final product.
For the biocidal product as supplied: for industrial use only.
Category(ies) of users industrial
120/227 ELI: http://data.europa.eu/eli/reg_impl/2025/2202/ojEN
OJ L, 20.11.2025
Pack sizes and packaging material For industrial and professional users:
— HDPE flask: 5 L (nominal)
— HDPE Pail / Jerrycan: 10 L, 20 L, 25 L, 30 L (nominal)
— Box with HDPE liner: 20 L
— HDPE Drum: 110 L, 120 L, 200 L, 260 L
— HDPE IBC: 650 L, 800 L, 1 000 L, 1 250 L
All products should be transport and stored in a vented room.
4.10.1. Use-specific instructions for use
— The preservative can be added at any stage of the production of the product.
— Earliest possible addition is recommended for optimal protection.
— Consult the manufacturer to determine the optimal dosage for the various products to be preserved.
— It is recommended that the optimum biocide concentration and compatibility with individual formulations
is determined by means of laboratory tests.
— The duration and storage conditions of the preserved matrices may impact the efficacy of the product,
microbiological tests should be conducted to determine the appropriate application rate without exceeding
the maximum authorised application rate.
— The biocidal product shall be used for treatment of products (articles/mixtures) distributed only to
professional users.
4.10.2. Use-specific risk mitigation measures
— During handling phases of products from Meta SPC 1, 2, 3 and 4 (mixing and loading), exposure to the
product (corrosive and skin sensitizer products) has to be limited by use of PPE and application of technical
and organisational RMM:
— Minimisation of manual phases (process automation);
— Use of a dosing device;
— Regular cleaning of equipment and work area;
— Avoidance of contact with contaminated tools and objects;
— Good standard of general ventilation;
— Training and management of staff on good practice.
— PPE is as follows:
— protective chemical resistant gloves (glove material to be specified by the authorisation holder within
the product information);
— protective coverall (at least type 3 or 4, EN 14605) which is impermeable for the biocidal product
shall be worn (coverall material to be specified by the authorisation holder within the product
information);
— Eye protection;
— Substance/task appropriate respirator if ventilation is inadequate.
ELI: http://data.europa.eu/eli/reg_impl/2025/2202/oj 121/227EN
OJ L, 20.11.2025
The maximal products concentration used for the preservation of mineral slurries being above the threshold value
of 15 ppm, exposure has to be limited by use of PPE, protecting skin and mucous membranes potentially exposed,
and application of technical and organisational RMM:
— Minimisation of manual phases;
— Use of a dosing device;
— Regular cleaning of equipment and work area;
— Good standard of general ventilation;
— Training and management of staff on good practice.
4.10.3. Where specific to the use, the particulars of likely direct or indirect effects, first aid instructions and emergency measures to
protect the environment
See general directions for use.
4.10.4. Where specific to the use, the instructions for safe disposal of the product and its packaging
See general directions for use.
4.10.5. Where specific to the use, the conditions of storage and shelf-life of the product under normal conditions of storage
See general directions for use.
4.11. Use description
Table 11
Preservation of building products applied indoor only
Product type PT06: Preservatives for products during storage
Where relevant, an exact description of -
the authorised use
Target organism(s) (including Scientific name: no data
development stage) Common name: Bacteria
Development stage: no data
Scientific name: no data
Common name: Yeasts
Development stage: no data
Field(s) of use indoor use
Preservation of building (construction) products (including sealants,
caulks, plasters etc.)
The biocidal product is recommended to control the growth of
bacteria in building (construction) products (sealants, caulks,
biopolymers, plasters, fillers, admixtures concrete additives, joints
compounds,..).
Application method(s) Method: -
Detailed description:
Manual and automated dosing. The biocidal product should be
dispensed to the end use fluid at a point to ensure adequate mixing
using preferably automated metering pump or by manual addition.
122/227 ELI: http://data.europa.eu/eli/reg_impl/2025/2202/ojEN
OJ L, 20.11.2025
Application rate(s) and frequency Application Rate:
Industrial uses: 1,5 - 14,5 % C(M)IT/MIT in the biocidal products;
Professional uses: Add at typical use rate between 16,2-30 mg C(M)
IT/MIT (3:1) per Kg final product to be treated.
-
Number and timing of application:
The biocidal product is added at single dose at the time of
manufacture, storage or shipment.
Slowly dispense using automated metering or manually. Mix
thoroughly until the biocidal product is evenly dispersed.
Industrial uses:
1,5 - 14,5 % C(M)IT/MIT in the biocidal products.
Professional uses:
Add at typical use rate between 16,2-30 mg C(M)IT/MIT (3:1) per Kg
final product to be treated.
For the biocidal product as supplied: for industrial use only.
Category(ies) of users industrial
Pack sizes and packaging material For industrial and professional users:
— HDPE flask: 5 L (nominal)
— HDPE Pail / Jerrycan: 10 L, 20 L, 25 L, 30 L (nominal)
— Box with HDPE liner: 20 L
— HDPE Drum: 110 L, 120 L, 200 L, 260 L
— HDPE IBC: 650 L, 800 L, 1 000 L, 1 250 L
All products should be transport and stored in a vented room.
4.11.1. Use-specific instructions for use
— The preservative can be added at any stage of the production of the product.
— Earliest possible addition is recommended for optimal protection.
— Consult the manufacturer to determine the optimal dosage for the various products to be preserved.
— It is recommended that the optimum biocide concentration and compatibility with individual formulations
is determined by means of laboratory tests.
— The duration and storage conditions of the preserved matrices may impact the efficacy of the product,
microbiological tests should be conducted to determine the appropriate application rate without exceeding
the maximum authorised application rate.
— The biocidal product shall be used for treatment of products (articles/mixtures) distributed only to
professional users.
4.11.2. Use-specific risk mitigation measures
— This use is restricted to the preservation of building material applied indoor only.
— During handling phases for products from Meta SPC 1, 3 and 4 (mixing and loading), exposure to the
product (corrosive and skin sensitizer products) has to be limited by use of PPE and application of technical
and organisational RMM:
— Minimisation of manual phases (process automation);
— Use of a dosing device;
ELI: http://data.europa.eu/eli/reg_impl/2025/2202/oj 123/227EN
OJ L, 20.11.2025
— Regular cleaning of equipment and work area;
— Avoidance of contact with contaminated tools and objects;
— Good standard of general ventilation;
— Training and management of staff on good practice.
— PPE is as follows:
— protective chemical resistant gloves (glove material to be specified by the authorisation holder within
the product information);
— protective coverall (at least type 3 or 4, EN 14605) which is impermeable for the biocidal product
shall be worn (coverall material to be specified by the authorisation holder within the product
information);
— Eye protection;
— Substance/task appropriate respirator if ventilation is inadequate.
For professional users, the maximal products concentration used for the preservation of building products being
above the threshold value of 15 ppm, exposure has to be limited by use of PPE, protecting skin and mucous
membranes potentially exposed, and application of technical and organisational RMM:
— Minimisation of manual phases;
— Regular cleaning of equipment and work area;
— Good standard of general ventilation;
— Training and management of staff on good practice.
4.11.3. Where specific to the use, the particulars of likely direct or indirect effects, first aid instructions and emergency measures to
protect the environment
See general directions for use.
4.11.4. Where specific to the use, the instructions for safe disposal of the product and its packaging
See general directions for use.
4.11.5. Where specific to the use, the conditions of storage and shelf-life of the product under normal conditions of storage
See general directions for use.
4.12. Use description
Table 12
Preservation of electronic chemicals – Curative treatment
Product type PT06: Preservatives for products during storage
Where relevant, an exact description of -
the authorised use
Target organism(s) (including Scientific name: no data
development stage) Common name: Bacteria
Development stage: no data
Scientific name: no data
Common name: Yeasts
Development stage: no data
124/227 ELI: http://data.europa.eu/eli/reg_impl/2025/2202/ojEN
OJ L, 20.11.2025
Scientific name: no data
Common name: fungi
Development stage: no data
Field(s) of use indoor use
Preservation of electronic chemicals
The biocidal product is used to reduce contamination by bacteria,
yeasts and fungi in electronic chemicals as Chemical Mechanical
Polishing (CMP) silica slurries.
Application method(s) Method: closed system
Detailed description:
Manual and automated application. The biocidal product should be
dispensed to the end use fluid at a point to ensure adequate mixing
using preferably automated metering pump or by manual addition.
Application rate(s) and frequency Application Rate:
Industrial uses: 1,5 - 14,5 % C(M)IT/MIT in the biocidal products;
Professional uses: Add at typical use rate between 10-30 mg C(M)
IT/MIT (3:1) per L final product to be treated.
-
Number and timing of application:
The biocidal product is added at single dose at the time of
manufacture, storage or shipment.
Slowly dispense using automated metering or manually. Mix
thoroughly until the biocidal product is evenly dispersed.
Industrial uses: 1,5 - 14,5 % C(M)IT/MIT in the biocidal products.
Professional uses
Curative treatment:
10-30 mg C(M)IT/MIT (3:1) per kg final product to be treated.
Contact time: 7 days
For the biocidal product as supplied: for industrial use only.
Category(ies) of users industrial
Pack sizes and packaging material For industrial and professional users:
— HDPE flask: 5 L (nominal)
— HDPE Pail / Jerrycan: 10 L, 20 L, 25 L, 30 L (nominal)
— Box with HDPE liner: 20 L
— HDPE Drum: 110 L, 120 L, 200 L, 260 L
— HDPE IBC: 650 L, 800 L, 1 000 L, 1 250 L
All products should be transport and stored in a vented room.
4.12.1. Use-specific instructions for use
— The preservative can be added at any stage of the production of the product.
— Earliest possible addition is recommended for optimal protection.
— Consult the manufacturer to determine the optimal dosage for the various products to be preserved.
ELI: http://data.europa.eu/eli/reg_impl/2025/2202/oj 125/227EN
OJ L, 20.11.2025
— It is recommended that the optimum biocide concentration and compatibility with individual formulations
is determined by means of laboratory tests.
— The duration and storage conditions of the preserved matrices may impact the efficacy of the product,
microbiological tests should be conducted to determine the appropriate application rate without exceeding
the maximum authorised application rate.
— The biocidal product shall be used for treatment of products (articles/mixtures) distributed only to
professional users.
4.12.2. Use-specific risk mitigation measures
— During handling phases for products from Meta SPC 3 (mixing and loading), exposure to the product
(corrosive and skin sensitizer products) has to be limited by use of PPE and application of technical and
organisational RMM:
— Minimisation of manual phases (process automation);
— Use of a dosing device;
— Regular cleaning of equipment and work area;
— Avoidance of contact with contaminated tools and objects;
— Good standard of general ventilation;
— Training and management of staff on good practice.
— PPE is as follows:
— protective chemical resistant gloves (glove material to be specified by the authorisation holder within
the product information);
— protective coverall (at least type 3 or 4, EN 14605) which is impermeable for the biocidal product
shall be worn (coverall material to be specified by the authorisation holder within the product
information);
— Eye protection;
— Substance/task appropriate respirator if ventilation is inadequate.
— The maximal products concentration used for the preservation of electronic chemicals being above the
threshold value of 15 ppm, exposure has to be limited by use of PPE, protecting skin and mucous
membranes potentially exposed, and application of technical and organisational RMM:
— Minimisation of manual phases;
— Use of a dosing device;
— Regular cleaning of equipment and work area;
— Good standard of general ventilation;
— Training and management of staff on good practice.
4.12.3. Where specific to the use, the particulars of likely direct or indirect effects, first aid instructions and emergency measures to
protect the environment
See general directions for use.
4.12.4. Where specific to the use, the instructions for safe disposal of the product and its packaging
See general directions for use.
126/227 ELI: http://data.europa.eu/eli/reg_impl/2025/2202/ojEN
OJ L, 20.11.2025
4.12.5. Where specific to the use, the conditions of storage and shelf-life of the product under normal conditions of storage
See general directions for use.
4.13. Use description
Table 13
Preservation of inks
Product type PT06: Preservatives for products during storage
Where relevant, an exact description of -
the authorised use
Target organism(s) (including Scientific name: no data
development stage) Common name: Bacteria
Development stage: no data
Scientific name: no data
Common name: Yeasts
Development stage: no data
Field(s) of use indoor use
Preservation of inks
The biocidal product is recommended to control the growth of
bacteria and yeasts in inks and ink components (printing inks
lithographic, photographic, ink-jet fluids, water based dampening or
fountain solutions inks used for textile printing). The biocidal product
inhibits the growth of microorganisms, which would otherwise lead
to odour formation, viscosity alteration, product discolouration and
premature product failure.
Application method(s) Method: closed system
Detailed description:
Manual and automated dosing. The biocidal product should be
dispensed to the end use fluid at a point to ensure adequate mixing
using preferably automated metering pump or by manual addition.
Application rate(s) and frequency Application Rate:
Industrial uses: 1,5 - 14,5 % C(M)IT/MIT in the biocidal products.
Professional uses: 6-30 mg C(M)IT/MIT (3:1) /kg final product.
General public uses: 6-14,9 mg C(M)IT/MIT (3:1) /kg final product.
-
Number and timing of application:
The biocidal product is added at single dose at time of manufacturing,
storage or shipment.
Industrial uses: 1,5 - 14,5 % C(M)IT/MIT in the biocidal products.
Professional uses:
6-30 mg C(M)IT/MIT (3:1) /kg final product.
General public uses:
6-14,9 mg C(M)IT/MIT (3:1) /kg final product.
For the biocidal product as supplied: for industrial use only.
ELI: http://data.europa.eu/eli/reg_impl/2025/2202/oj 127/227EN
OJ L, 20.11.2025
Category(ies) of users industrial
Pack sizes and packaging material For industrial and professional users:
— HDPE flask: 5 L (nominal)
— HDPE Pail / Jerrycan: 10 L, 20 L, 25 L, 30 L (nominal)
— Box with HDPE liner: 20 L
— HDPE Drum: 110 L, 120 L, 200 L, 260 L
— HDPE IBC: 650 L, 800 L, 1 000 L, 1 250 L
All products should be transport and stored in a vented room.
4.13.1. Use-specific instructions for use
— The preservative can be added at any stage of the production of the product.
— Earliest possible addition is recommended for optimal protection.
— Consult the manufacturer to determine the optimal dosage for the various products to be preserved.
— It is recommended that the optimum biocide concentration and compatibility with individual formulations
is determined by means of laboratory tests.
— The duration and storage conditions of the preserved matrices may impact the efficacy of the product,
microbiological tests should be conducted to determine the appropriate application rate without exceeding
the maximum authorised application rate.
— The biocidal product shall be used for treatment of products (articles/mixtures) distributed to professional
users and to the general public. For products distributed to the general public the maximal concentration
used must be below the threshold value of 15 ppm.
4.13.2. Use-specific risk mitigation measures
— During handling phases of products from Meta SPC 1, 2, 3 and 4 (mixing and loading), exposure to the
product (corrosive and skin sensitizer products) has to be limited by use of PPE and application of technical
and organisational RMM:
— Minimisation of manual phases (process automation);
— Use of a dosing device;
— Regular cleaning of equipment and work area;
— Avoidance of contact with contaminated tools and objects;
— Good standard of general ventilation;
— Training and management of staff on good practice.
— PPE is as follows:
— protective chemical resistant gloves (glove material to be specified by the authorisation holder within
the product information);
— protective coverall (at least type 3 or 4, EN 14605) which is impermeable for the biocidal product
shall be worn (coverall material to be specified by the authorisation holder within the product
information);
— Eye protection;
— Substance/task appropriate respirator if ventilation is inadequate.
128/227 ELI: http://data.europa.eu/eli/reg_impl/2025/2202/ojEN
OJ L, 20.11.2025
— For professional users, the maximal products concentration used for the preservation of inks being above
the threshold value of 15 ppm, exposure has to be limited by use of PPE, protecting skin and mucous
membranes potentially exposed, and application of technical and organisational RMM:
— Minimisation of manual phases;
— Use of a dosing device;
— Regular cleaning of equipment and work area;
— Good standard of general ventilation;
— Training and management of staff on good practice.
4.13.3. Where specific to the use, the particulars of likely direct or indirect effects, first aid instructions and emergency measures to
protect the environment
See general directions for use.
4.13.4. Where specific to the use, the instructions for safe disposal of the product and its packaging
See general directions for use.
4.13.5. Where specific to the use, the conditions of storage and shelf-life of the product under normal conditions of storage
See general directions for use.
4.14. Use description
Table 14
Preservation of functional fluids (hydraulic fluids, antifreeze, corrosion inhibitors, etc. - excluding fuel
additives)
Product type PT06: Preservatives for products during storage
Where relevant, an exact description of -
the authorised use
Target organism(s) (including Scientific name: no data
development stage) Common name: Bacteria
Development stage: no data
Field(s) of use indoor use
Preservation of functional fluids (hydraulic fluids, antifreeze,
corrosion inhibitors, etc. - excluding fuel additives)
The biocidal product is recommended to control the growth of
bacteria in functional fluids such as brake and hydraulic fluids,
antifreeze additives, corrosion inhibitors, spinning fluids. The
biocidal product inhibits the growth microorganisms, which would
otherwise lead to odours formation, viscosity alteration,
discolouration of product and premature product failure.
Application method(s) Method: closed system
Detailed description:
Manual and automated dosing. The biocidal product should be
dispensed to the end use fluid at a point to ensure adequate mixing
using preferably automated metering pump or by manual addition.
ELI: http://data.europa.eu/eli/reg_impl/2025/2202/oj 129/227EN
OJ L, 20.11.2025
Application rate(s) and frequency Application Rate:
Industrial uses: 1,5 - 14,5 % C(M)IT/MIT in the biocidal products.
Professional uses: Add at a typical use rate between 6 to 30 mg C(M)
IT/MIT (3:1) per kg final product to be treated.
-
Number and timing of application:
The biocidal product is added at single dose at time of manufacturing,
storage or shipment.
Industrial uses: 1,5 - 14,5 % C(M)IT/MIT in the biocidal products.
Professional uses:
Add at a typical use rate between 6 to 30 mg C(M)IT/MIT (3:1) per kg
final product to be treated
For the biocidal product as supplied: for industrial use only.
Category(ies) of users industrial
Pack sizes and packaging material For industrial and professional users:
— HDPE flask: 5 L (nominal)
— HDPE Pail / Jerrycan: 10 L, 20 L, 25 L, 30 L (nominal)
— Box with HDPE liner: 20 L
— HDPE Drum: 110 L, 120 L, 200 L, 260 L
— HDPE IBC: 650 L, 800 L, 1 000 L, 1 250 L
All products should be transport and stored in a vented room.
4.14.1. Use-specific instructions for use
— The preservative can be added at any stage of the production of the product.
— Earliest possible addition is recommended for optimal protection.
— Consult the manufacturer to determine the optimal dosage for the various products to be preserved.
— It is recommended that the optimum biocide concentration and compatibility with individual formulations
is determined by means of laboratory tests.
— The duration and storage conditions of the preserved matrices may impact the efficacy of the product,
microbiological tests should be conducted to determine the appropriate application rate without exceeding
the maximum authorised application rate.
— The biocidal product shall be used for treatment of products (articles/mixtures) distributed only to
professional users.
4.14.2. Use-specific risk mitigation measures
— During handling phases of products from Meta SPC 1, 2, 3 and 4 (mixing and loading), exposure to the
product (corrosive and skin sensitizer products) has to be limited by use of PPE and application of technical
and organisational RMM:
— Minimisation of manual phases (process automation);
— Use of a dosing device;
— Regular cleaning of equipment and work area;
— Avoidance of contact with contaminated tools and objects;
130/227 ELI: http://data.europa.eu/eli/reg_impl/2025/2202/ojEN
OJ L, 20.11.2025
— Good standard of general ventilation;
— Training and management of staff on good practice.
— PPE is as follows:
— protective chemical resistant gloves (glove material to be specified by the authorisation holder within
the product information);
— protective coverall (at least type 3 or 4, EN 14605) which is impermeable for the biocidal product
shall be worn (coverall material to be specified by the authorisation holder within the product
information);
— Eye protection;
— Substance/task appropriate respirator if ventilation is inadequate.
— The maximal products concentration used for the preservation of functional fluids (hydraulic fluids,
antifreeze, corrosion inhibitors, etc…) being above the threshold value of 15 ppm, exposure has to be
limited by use of PPE, protecting skin and mucous membranes potentially exposed, and application of
technical and organisational RMM:
— Minimisation of manual phases;
— Use of a dosing device;
— Regular cleaning of equipment and work area;
— Good standard of general ventilation;
— Training and management of staff on good practice.
4.14.3. Where specific to the use, the particulars of likely direct or indirect effects, first aid instructions and emergency measures to
protect the environment
See general directions for use.
4.14.4. Where specific to the use, the instructions for safe disposal of the product and its packaging
See general directions for use.
4.14.5. Where specific to the use, the conditions of storage and shelf-life of the product under normal conditions of storage
See general directions for use.
4.15. Use description
Table 15
Preservation of laboratory reagents
Product type PT06: Preservatives for products during storage
Where relevant, an exact description of -
the authorised use
Target organism(s) (including Scientific name: no data
development stage) Common name: Bacteria
Development stage: no data
Scientific name: no data
Common name: Yeasts
Development stage: no data
ELI: http://data.europa.eu/eli/reg_impl/2025/2202/oj 131/227EN
OJ L, 20.11.2025
Field(s) of use indoor use
Preservation of laboratory reagents
.
The biocidal product is recommended to control the growth of
bacteria and yeasts in laboratory reagents.
Application method(s) Method: closed system
Detailed description:
Manual and automated dosing. The biocidal product should be
dispensed to the end use fluid at a point to ensure adequate mixing
using preferably automated metering pump or by manual addition.
Application rate(s) and frequency Application Rate:
Industrial uses: 1,5 - 14,5 % C(M)IT/MIT in the biocidal products.
Professional use: Add at typical use rate of 15,2 mg C(M)IT/MIT (3:1)
per kg final product to be treated.
-
Number and timing of application:
The biocidal product is added at single dose at the time of
manufacture, storage or shipment.
Slowly dispense using automated metering or manually. Mix
thoroughly until the biocidal product is evenly dispersed.
Industrial uses: 1,5 - 14,5 % C(M)IT/MIT in the biocidal products.
Professional use: Add at typical use rate of 15,2 mg C(M)IT/MIT (3:1)
per kg final product to be treated.
For the biocidal product as supplied: for industrial use only.
Category(ies) of users industrial
Pack sizes and packaging material For industrial and professional users:
— HDPE flask: 1 L
— HDPE flask: 5 L (nominal)
— HDPE Pail / Jerrycan: 10 L, 20 L, 25 L, 30 L (nominal)
— Box with HDPE liner: 20 L
— HDPE Drum: 110 L, 120 L, 200 L, 260 L
— HDPE IBC: 650 L, 800 L, 1 000 L, 1 250 L
All products should be transport and stored in a vented room.
4.15.1. Use-specific instructions for use
— The preservative can be added at any stage of the production of the product.
— Earliest possible addition is recommended for optimal protection.
— Consult the manufacturer to determine the optimal dosage for the various products to be preserved.
— It is recommended that the optimum biocide concentration and compatibility with individual formulations
is determined by means of laboratory tests.
132/227 ELI: http://data.europa.eu/eli/reg_impl/2025/2202/ojEN
OJ L, 20.11.2025
— The duration and storage conditions of the preserved matrices may impact the efficacy of the product,
microbiological tests should be conducted to determine the appropriate application rate without exceeding
the maximum authorised application rate.
— The biocidal product shall be used for treatment of products (articles/mixtures) distributed only to
professional users.
4.15.2. Use-specific risk mitigation measures
— During handling phases for products from Meta SPC 1, 3 and 4 (mixing and loading), exposure to the
product (corrosive and skin sensitizer products) has to be limited by use of PPE and application of technical
and organisational RMM:
— Minimisation of manual phases (process automation);
— Use of a dosing device;
— Regular cleaning of equipment and work area;
— Avoidance of contact with contaminated tools and objects;
— Good standard of general ventilation;
— Training and management of staff on good practice.
— PPE is as follows:
— protective chemical resistant gloves (glove material to be specified by the authorisation holder within
the product information);
— protective coverall (at least type 3 or 4, EN 14605) which is impermeable for the biocidal product
shall be worn (coverall material to be specified by the authorisation holder within the product
information);
— Eye protection;
— Substance/task appropriate respirator if ventilation is inadequate.
For professional users, the maximal products concentration used for the preservation of laboratory reagents being
above the threshold value of 15 ppm, exposure has to be limited by use of PPE, protecting skin and mucous
membranes potentially exposed, and application of technical and organisational RMM:
— Minimisation of manual phases;
— Use of a dosing device;
— Regular cleaning of equipment and work area;
— Good standard of general ventilation;
— Training and management of staff on good practice.
4.15.3. Where specific to the use, the particulars of likely direct or indirect effects, first aid instructions and emergency measures to
protect the environment
See general directions for use.
4.15.4. Where specific to the use, the instructions for safe disposal of the product and its packaging
See general directions for use.
4.15.5. Where specific to the use, the conditions of storage and shelf-life of the product under normal conditions of storage
See general directions for use.
ELI: http://data.europa.eu/eli/reg_impl/2025/2202/oj 133/227EN
OJ L, 20.11.2025
4.16. Use description
Table 16
Offline preservation of industrial reverse osmosis membranes
Product type PT06: Preservatives for products during storage
Where relevant, an exact description of -
the authorised use
Target organism(s) (including Scientific name: no data
development stage) Common name: Bacteria
Development stage: no data
Field(s) of use indoor use
Offline preservation of industrial reverse osmosis membranes
The biocidal product is recommended to control the growth of
bacteria of reverse osmosis and nanofiltration membranes producing
industrial water for extended periods of time.
Application method(s) Method: closed system
Detailed description:
Manual and automated dosing. The biocidal product should be
dispensed as a tankside additive into the circulating use-dilution of
the fluid, using a metering pump or by manual pouring, at a point to
ensure adequate mixing throughout the system. After complete filling
of the trains RO/NF systems with the biocide solution, pumps are
stopped (Off line treatment) for extended periods of time. Typically
C(M)IT/MIT (3:1) solutions are prepared in the CIP (cleaning in place)
tank and added via the dosing system. Dilution with permeate water
or high quality water is recommended for the preparation of the
biocide solution. Membranes should be soaked in the biocide solution
during the shut-down period.
Application rate(s) and frequency Application Rate:
7,5–20 g/m3 (ppm w/v) of C(M)IT/MIT (3:1).
-
Number and timing of application:
7,5–20 g/m3 (ppm w/v) of C(M)IT/MIT (3:1).
Category(ies) of users industrial
Pack sizes and packaging material For industrial and professional users:
— HDPE flask: 5 L (nominal)
— HDPE Pail / Jerrycan: 10 L, 20 L, 25 L, 30 L (nominal)
— Box with HDPE liner: 20 L
— HDPE Drum: 110 L, 120 L, 200 L, 260 L
— HDPE IBC: 650 L, 800 L, 1 000 L, 1 250 L
All products should be transport and stored in a vented room.
4.16.1. Use-specific instructions for use
— The preservative can be added at any stage of the production of the product.
— Earliest possible addition is recommended for optimal protection.
134/227 ELI: http://data.europa.eu/eli/reg_impl/2025/2202/ojEN
OJ L, 20.11.2025
— Consult the manufacturer to determine the optimal dosage for the various products to be preserved.
— It is recommended that the optimum biocide concentration and compatibility with individual formulations
is determined by means of laboratory tests.
— The duration and storage conditions of the preserved matrices may impact the efficacy of the product,
microbiological tests should be conducted to determine the appropriate application rate without exceeding
the maximum authorised application rate.
4.16.2. Use-specific risk mitigation measures
Rinse the system with water prior to perform the maintenance of the system.
— During handling phases for products from Meta SPC 1, 3 and 4 (mixing and loading), exposure to the
product (corrosive and skin sensitizer products) has to be limited by use of PPE and application of technical
and organisational RMM:
— Minimisation of manual phases (process automation);
— Use of a dosing device;
— Regular cleaning of equipment and work area;
— Avoidance of contact with contaminated tools and objects;
— Good standard of general ventilation;
— Training and management of staff on good practice.
— PPE is as follows:
— protective chemical resistant gloves (glove material to be specified by the authorisation holder within
the product information);
— protective coverall (at least type 3 or 4, EN 14605) which is impermeable for the biocidal product
shall be worn (coverall material to be specified by the authorisation holder within the product
information);
— Eye protection;
— Substance/task appropriate respirator if ventilation is inadequate.
4.16.3. Where specific to the use, the particulars of likely direct or indirect effects, first aid instructions and emergency measures to
protect the environment
See general directions for use.
4.16.4. Where specific to the use, the instructions for safe disposal of the product and its packaging
See general directions for use.
4.16.5. Where specific to the use, the conditions of storage and shelf-life of the product under normal conditions of storage
See general directions for use.
ELI: http://data.europa.eu/eli/reg_impl/2025/2202/oj 135/227EN
OJ L, 20.11.2025
4.17. Use description
Table 17
Preservation of liquids used in closed recirculating cooling systems
Product type PT11: Preservatives for liquid-cooling and processing systems
Where relevant, an exact description of -
the authorised use
Target organism(s) (including Scientific name: no data
development stage) Common name: Bacteria (including Legionella pneumophila)
Development stage: no data
Scientific name: no data
Common name: Yeasts
Development stage: no data
Scientific name: no data
Common name: fungi
Development stage: no data
Field(s) of use indoor use
outdoor use
Preservation of liquids used in closed recirculating cooling systems
(Closed re-circulating cooling water systems comprise compressor
cooling, air conditioning chilled water, boilers, engine jacket cooling,
power supply cooling, and other industrial processes).
The biocidal product is used to control the growth of aerobes and
anaerobes bacteria, yeast, fungi, and biofilm in the circulating water
of closed systems
Application method(s) Method: closed system
Detailed description:
Manual and automated dosing.
Application rate(s) and frequency Application Rate:
Curative efficacy:- against bacteria (including L. pneumophila) at 5 -
14,9 g C(M)IT/MIT (3:1) / m3 of water. Contact time: 24 hours -
against biofilm: 14,9 g C(M)IT/MIT (3:1) / m3 of water. Contact time:
24 hours.- against fungi and yeasts at 1 – 3 g C(M)IT/MIT (3:1) / m3
of water. Contact time: 48 hours. Preventive efficacy:- against bacteria
(including L. pneumophila) at 3 – 14,9 g C(M)IT/MIT (3:1) / m3 of
water. - against biofilm (including L. pneumophila): 3 g C(M)IT/MIT
(3:1) / m3 of water.
-
Number and timing of application:
Curative efficacy:
— against bacteria (including L. pneumophila) at 5 - 14,9 g C(M)
IT/MIT (3:1) / m3 of water.
Contact time: 24 hours
— against biofilm: 14,9 g C(M)IT/MIT (3:1) / m3 of water.
Contact time: 24 hours
— against fungi and yeasts at 1 – 3 g C(M)IT/MIT (3:1) / m3 of water.
Contact time: 48 hours
Preventive efficacy:
against bacteria (including L. pneumophila) at 3 – 14,9 g C(M)IT/MIT
(3:1) / m3 of water.
against biofilm (including L. pneumophila): 3 g C(M)IT/MIT (3:1) /
m3 of water.
136/227 ELI: http://data.europa.eu/eli/reg_impl/2025/2202/ojEN
OJ L, 20.11.2025
Category(ies) of users industrial
Pack sizes and packaging material For industrial and professional users:
— HDPE flask: 5 L (nominal)
— HDPE Pail / Jerrycan: 10 L, 20 L, 25 L, 30 L (nominal)
— Box with HDPE liner: 20 L
— HDPE Drum: 110 L, 120 L, 200 L, 260 L
— HDPE IBC: 650 L, 800 L, 1 000 L, 1 250 L
All products should be transport and stored in a vented room.
4.17.1. Use-specific instructions for use
Microbiological tests to prove adequacy of preservation have to be undertaken by the user of C(M)IT/MIT products
in order to determine the effective dose of the preservative for the specific matrix/location/system. If needed,
consult the manufacturer of the preservative product.
4.17.2. Use-specific risk mitigation measures
— Rinse the system (especially the dispensing pumps) with water prior to perform the cleaning step.
— During handling phases (mixing and loading) and cleaning of the dispensing pumps, exposure to the
product (corrosive and skin sensitizer product) has to be limited by use of PPE and application of technical
and organisational RMM:
— Minimisation of manual phases (process automation);
— Use of a dosing device;
— Regular cleaning of equipment and work area;
— Avoidance of contact with contaminated tools and objects;
— Good standard of general ventilation;
— Training and management of staff on good practice.
— PPE is as follows:
— protective chemical resistant gloves (glove material to be specified by the authorisation holder within
the product information);
— protective coverall (at least type 3 or 4, EN 14605) which is impermeable for the biocidal product
shall be worn (coverall material to be specified by the authorisation holder within the product
information);
— Eye protection;
— Substance/task appropriate respirator if ventilation is inadequate.
4.17.3. Where specific to the use, the particulars of likely direct or indirect effects, first aid instructions and emergency measures to
protect the environment
See general directions for use.
4.17.4. Where specific to the use, the instructions for safe disposal of the product and its packaging
See general directions for use.
ELI: http://data.europa.eu/eli/reg_impl/2025/2202/oj 137/227EN
OJ L, 20.11.2025
4.17.5. Where specific to the use, the conditions of storage and shelf-life of the product under normal conditions of storage
See general directions for use.
4.18. Use description
Table 18
Preservation of liquids used in small open recirculating cooling systems
Product type PT11: Preservatives for liquid-cooling and processing systems
Where relevant, an exact description of -
the authorised use
Target organism(s) (including Scientific name: no data
development stage) Common name: Bacteria (including Legionella pneumophila)
Development stage: no data
Scientific name: no data
Common name: Yeasts
Development stage: no data
Scientific name: no data
Common name: fungi
Development stage: no data
Scientific name: no data
Common name: Algae (green algae and cyanobacteria)
Development stage: no data
Field(s) of use indoor use
outdoor use
Preservation of liquids used in small open recirculating cooling
systems (blowdown and recirculating flow rates, as well as total
volume of water limited to 2 m3/h, and 100 m3/h and 300 m3
respectively)
Process and cooling water: Used to control the growth of bacteria,
algae, fungi and biofilm
Application method(s) Method: open system
Detailed description:
Manual and automated dosing. .
Application rate(s) and frequency Application Rate:
Curative treatment Against bacteria (including L. pneumophila) at 5 –
14,9 g C(M)IT/MIT (3:1) / m3 of water , - against biofilm (including L.
pneumophila) at 1,5 to 14,9 g C(M)IT/MIT (3:1) / m3 of water, -
against fungi (including yeast) at 1 – 14,9 g C(M)IT/MIT (3:1) / m3 of
water. Preventive treatment: - Against bacteria, green algae and
cyanobacteria at 3 g C(M)IT/MIT (3:1) / m3 of water, - against biofilm
(including L. pneumophila) at 3 g C(M)IT/MIT (3:1) / m3 of water.
-
Number and timing of application:
Curative treatment:
— Against bacteria (including L. pneumophila) at 5 – 14,9 g C(M)
IT/MIT (3:1) / m3 of water
138/227 ELI: http://data.europa.eu/eli/reg_impl/2025/2202/ojEN
OJ L, 20.11.2025
Contact time: 24 hours
— against biofilm (including L. pneumophila) at 1,5 - 14,9 g C(M)
IT/MIT (3:1) / m3 of water
Contact time: 48 hours.
— against fungi and yeast at 1 – 14,9 g C(M)IT/MIT (3:1) / m3 of
water
Contact time: 48 hours.
Preventive treatment:
— against bacteria, green algae and cyanobacteria at 3 g C(M)IT/MIT
(3:1) / m3 of water.
— against biofilm (including L. pneumophila) at 3 g C(M)IT/MIT (3:1)
/ m3 of water.
Category(ies) of users industrial
Pack sizes and packaging material For industrial and professional users:
— HDPE flask: 5 L (nominal)
— HDPE Pail / Jerrycan: 10 L, 20 L, 25 L, 30 L (nominal)
— Box with HDPE liner: 20 L
— HDPE Drum: 110 L, 120 L, 200 L, 260 L
— HDPE IBC: 650 L, 800 L, 1 000 L, 1 250 L
All products should be transport and stored in a vented room.
4.18.1. Use-specific instructions for use
Microbiological tests to prove adequacy of preservation have to be undertaken by the user of C(M)IT/MIT products
in order to determine the effective dose of the preservative for the specific matrix/location/system. If needed,
consult the manufacturer of the preservative product.
4.18.2. Use-specific risk mitigation measures
— Rinse the system (especially the dispensing pumps) with water prior to perform the cleaning step.
— During handling phases (mixing and loading) and cleaning of the dispensing pumps, exposure to the
product (corrosive and skin sensitizer product) has to be limited by use of PPE and application of technical
and organisational RMM:
— Minimisation of manual phases (process automation);
— Use of a dosing device;
— Regular cleaning of equipment and work area;
— Avoidance of contact with contaminated tools and objects;
— Good standard of general ventilation;
— Training and management of staff on good practice.
— PPE is as follows:
— protective chemical resistant gloves (glove material to be specified by the authorisation holder within
the product information);
— protective coverall (at least type 3 or 4, EN 14605) which is impermeable for the biocidal product
shall be worn (coverall material to be specified by the authorisation holder within the product
information);
ELI: http://data.europa.eu/eli/reg_impl/2025/2202/oj 139/227EN
OJ L, 20.11.2025
— Eye protection;
— Substance/task appropriate respirator if ventilation is inadequate.
— Cooling fluid must not enter surface water directly. Use product only in premises that are connected to
a STP.
— The product can only be used when the cooling towers are equipped with drift eliminators that reduce the
drift at least by 99%.
4.18.3. Where specific to the use, the particulars of likely direct or indirect effects, first aid instructions and emergency measures to
protect the environment
See general directions for use.
4.18.4. Where specific to the use, the instructions for safe disposal of the product and its packaging
See general directions for use.
4.18.5. Where specific to the use, the conditions of storage and shelf-life of the product under normal conditions of storage
See general directions for use.
4.19. Use description
Table 19
Preservation of liquids used in pasteurizers, conveyor belts and air washers
Product type PT11: Preservatives for liquid-cooling and processing systems
Where relevant, an exact description of -
the authorised use
Target organism(s) (including Scientific name: no data
development stage) Common name: Bacteria (including Legionella pneumophila)
Development stage: no data
Scientific name: no data
Common name: Yeasts
Development stage: no data
Scientific name: no data
Common name: fungi
Development stage: no data
Scientific name: no data
Common name: Algae (green algae and cyanobacteria)
Development stage: no data
Field(s) of use indoor use
outdoor use
Preservation of liquids used in non-food pasteurizers and conveyor
belts, air washers.
Application method(s) Method: -
Detailed description:
The biocidal product is dosed automatically in the heat transfer fluid,
in a place of good mixing (e.g. collecting sump below the conveyor
belt). The feeding pipe is used to dose the biocidal product below the
water level in order to limit its evaporation.
140/227 ELI: http://data.europa.eu/eli/reg_impl/2025/2202/ojEN
OJ L, 20.11.2025
Application rate(s) and frequency Application Rate:
Curative treatment: -against bacteria (including L. pneumophila): 5 -
14,9 g C(M)IT/MIT (3:1) / m3 of water - against biofilm (including L.
pneumophila) at 1,5 - 14,9 g C(M)IT/MIT (3:1) / m3 of water - against
fungi and yeast at 1 – 14,9 g C(M)IT/MIT (3:1) / m3 of water.
Preventive treatment: Against bacteria, green algae and cyanobacteria
at 3 g C(M)IT/MIT (3:1) / m3 of water, against biofilm (including L.
pneumophila) at 3 g C(M)IT/MIT (3:1) / m3 of water.
-
Number and timing of application:
Curative treatment:
against bacteria (including L. pneumophila): 5 - 14,9 g C(M)IT/MIT
(3:1) / m3 of water.
Contact time: 24 hours
— against biofilm (including L. pneumophila) at 1,5 - 14,9 g C(M)
IT/MIT (3:1) / m3 of water
Contact time: 48 hours.
— against fungi and yeast at 1 – 14,9 g C(M)IT/MIT (3:1) / m3 of
water
Contact time: 48 hours.
Preventive treatment:
— Against bacteria, green algae and cyanobacteria at 3 g C(M)IT/MIT
(3:1) / m3 of water.
— against biofilm (including L. pneumophila) at 3 g C(M)IT/MIT (3:1)
/ m3 of water.
Category(ies) of users industrial
Pack sizes and packaging material For industrial and professional users:
— HDPE flask: 5 L (nominal)
— HDPE Pail / Jerrycan: 10 L, 20 L, 25 L, 30 L (nominal)
— Box with HDPE liner: 20 L
— HDPE Drum: 110 L, 120 L, 200 L, 260 L
— HDPE IBC: 650 L, 800 L, 1 000 L, 1 250 L
All products should be transport and stored in a vented room.
4.19.1. Use-specific instructions for use
Microbiological tests to prove adequacy of preservation have to be undertaken by the user of C(M)IT/MIT products
in order to determine the effective dose of the preservative for the specific matrix/location/system. If needed,
consult the manufacturer of the preservative product.
Air washers: For use only in industrial air-washer systems that maintain effective mist eliminating components.
4.19.2. Use-specific risk mitigation measures
— Rinse the system (especially the dispensing pumps) with water prior to perform the cleaning step.
— During handling phases (mixing and loading) and cleaning of the dispensing pumps, exposure to the
product (corrosive and skin sensitizer product) has to be limited by use of PPE and application of technical
and organisational RMM:
— Minimisation of manual phases (process automation);
ELI: http://data.europa.eu/eli/reg_impl/2025/2202/oj 141/227EN
OJ L, 20.11.2025
— Use of a dosing device;
— Regular cleaning of equipment and work area;
— Avoidance of contact with contaminated tools and objects;
— Good standard of general ventilation;
— Training and management of staff on good practice.
— PPE is as follows:
— protective chemical resistant gloves (glove material to be specified by the authorisation holder within
the product information);
— protective coverall (at least type 3 or 4, EN 14605) which is impermeable for the biocidal product
shall be worn (coverall material to be specified by the authorisation holder within the product
information);
— Eye protection;
— Substance/task appropriate respirator if ventilation is inadequate.
4.19.3. Where specific to the use, the particulars of likely direct or indirect effects, first aid instructions and emergency measures to
protect the environment
See general directions for use.
4.19.4. Where specific to the use, the instructions for safe disposal of the product and its packaging
See general directions for use.
4.19.5. Where specific to the use, the conditions of storage and shelf-life of the product under normal conditions of storage
See general directions for use.
4.20. Use description
Table 20
Preservation of wood treatment solutions
Product type PT11: Preservatives for liquid-cooling and processing systems
Where relevant, an exact description of -
the authorised use
Target organism(s) (including Scientific name: fungi
development stage) Common name: other
Development stage: no data
Field(s) of use indoor use
outdoor use
Preservation of wood treatment solutions for application on wood of
classes 1, 2 and 3 only. The biocidal product is used as a preservative
for aqueous wood preservative treatment solution during the wet-
state process used in timber treatment solutions.
142/227 ELI: http://data.europa.eu/eli/reg_impl/2025/2202/ojEN
OJ L, 20.11.2025
Application method(s) Method: -
Detailed description:
-
Application rate(s) and frequency Application Rate:
Preventive treatment: against fungi: 15 - 50 g C(M)IT/MIT (3:1) / m3
of in use wood preservation solution
-
Number and timing of application:
Preventive treatment: against fungi: 15 - 50 g C(M)IT/MIT (3:1) / m3
of in use wood preservation solution
Category(ies) of users industrial
Pack sizes and packaging material For industrial and professional users:
— HDPE flask: 5 L (nominal)
— HDPE Pail / Jerrycan: 10 L, 20 L, 25 L, 30 L (nominal)
— Box with HDPE liner: 20 L
— HDPE Drum: 110 L, 120 L, 200 L, 260 L
— HDPE IBC: 650 L, 800 L, 1 000 L, 1 250 L
All products should be transport and stored in a vented room.
4.20.1. Use-specific instructions for use
Microbiological tests to prove adequacy of preservation have to be undertaken by the user of C(M)IT/MIT products
in order to determine the effective dose of the preservative for the specific matrix/location/system. If needed,
consult the manufacturer of the preservative product.
— The biocidal product is not intended to function as a wood preservative against wood destroying fungus
relative to product type 8.
4.20.2. Use-specific risk mitigation measures
— During handling phases (mixing and loading) and cleaning phases, exposure to the product (corrosive and
skin sensitizer product) has to be limited by use of PPE and application of technical and organisational RMM:
— Minimisation of manual phases (process automation);
— Use of a dosing device;
— Regular cleaning of equipment and work area;
— Avoidance of contact with contaminated tools and objects;
— Good standard of general ventilation;
— Training and management of staff on good practice.
— PPE is as follows:
— protective chemical resistant gloves (glove material to be specified by the authorisation holder within
the product information);
— protective coverall (at least type 3 or 4, EN 14605) which is impermeable for the biocidal product
shall be worn (coverall material to be specified by the authorisation holder within the product
information);
— Eye protection;
— Substance/task appropriate respirator if ventilation is inadequate.
ELI: http://data.europa.eu/eli/reg_impl/2025/2202/oj 143/227EN
OJ L, 20.11.2025
— The product shall not be used in a wood treatment solution to be applied to wood which may come in direct
contact with food, feeding stuff and livestock animals
— The product can be used to preserve wood treatment solutions for the treatment of wood in use classes 1, 2
and 3 only.
— The product can be used in a wood treatment solution where the industrial application processes of wood
treatment can be carried out within a contained area situated on impermeable hard standing with bunding
to prevent run-off and a recovery system in place (e.g. sump).
— The product can be used in wood treatment solutions for the preservation of freshly treated timber, which
after treatment is stored under shelter or on impermeable hard standing, or both, to prevent direct losses to
soil, sewer or water. Any losses of wood treatment solution shall be collected for reuse or disposal.
— The product can be used only in wood treatment solutions for industrial application if these cannot be
released to soil, ground- and surface water or any kind of sewer and the wood treatment solutions and/or
the product are collected and reused or disposed of as hazardous waste.
— The biocidal product can be used only in wood treatment solutions used for the treatment of objects or
materials which are stored until completely dried on impermeable ground and under roof, to avoid leakage
into the soil.
4.20.3. Where specific to the use, the particulars of likely direct or indirect effects, first aid instructions and emergency measures to
protect the environment
See general directions for use.
4.20.4. Where specific to the use, the instructions for safe disposal of the product and its packaging
See general directions for use.
4.20.5. Where specific to the use, the conditions of storage and shelf-life of the product under normal conditions of storage
See general directions for use.
4.21. Use description
Table 21
Preservation of recirculating fluids used in textile and fiber processing, leather processing, photo-
processing and fountain solution systems
Product type PT11: Preservatives for liquid-cooling and processing systems
Where relevant, an exact description of -
the authorised use
Target organism(s) (including Scientific name: no data
development stage) Common name: Bacteria
Development stage: no data
Field(s) of use indoor use
Preservation of recirculating fluids used in textile, fiber processing,
leather processing, photo-processing and fountain solution systems
144/227 ELI: http://data.europa.eu/eli/reg_impl/2025/2202/ojEN
OJ L, 20.11.2025
C(M)IT/MIT (3:1) biocidal products are used for the preservation of
textile and spinning fluids, photo processing solutions, leather
process (e.g. washing and soaking treatment stages) and printing
fountain solutions to control the integrity of recirculating fluid by
reducing microbial contamination in the bulk solution.
Application method(s) Method: -
Detailed description:
Manual and automated dosing.The preservation of all end-products is
performed in most cases highly automated by industrial usersThe
biocidal product is added to the central sump, basin or recirculating
lines in an area with adequate mixing.
Application rate(s) and frequency Application Rate:
Curative treatment: Against bacteria at 16-30 mg C(M)IT/MIT (3:1)
per L of fluid
-
Number and timing of application:
Curative treatment: Against bacteria at 16-30 mg C(M)IT/MIT (3:1)
per L of fluid
Contact time 5 days
Category(ies) of users industrial
Pack sizes and packaging material For industrial and professional users:
— HDPE flask: 5 L (nominal)
— HDPE Pail / Jerrycan: 10 L, 20 L, 25 L, 30 L (nominal)
— Box with HDPE liner: 20 L
— HDPE Drum: 110 L, 120 L, 200 L, 260 L
— HDPE IBC: 650 L, 800 L, 1 000 L, 1 250 L
All products should be transport and stored in a vented room.
4.21.1. Use-specific instructions for use
Microbiological tests to prove adequacy of preservation have to be undertaken by the user of C(M)IT/MIT products
in order to determine the effective dose of the preservative for the specific matrix/location/system. If needed,
consult the manufacturer of the preservative product.
4.21.2. Use-specific risk mitigation measures
— Rinse the system (especially the dispensing pumps) with water prior to perform the cleaning step.
— During handling phases (mixing and loading) and cleaning of the dispensing pumps, exposure to the
product (corrosive and skin sensitizer product) has to be limited by use of PPE and application of technical
and organisational RMM:
— Minimisation of manual phases (process automation);
— Use of a dosing device;
— Regular cleaning of equipment and work area;
— Avoidance of contact with contaminated tools and objects;
— Good standard of general ventilation;
— Training and management of staff on good practice.
ELI: http://data.europa.eu/eli/reg_impl/2025/2202/oj 145/227EN
OJ L, 20.11.2025
— PPE is as follows:
— protective chemical resistant gloves (glove material to be specified by the authorisation holder within
the product information);
— protective coverall (at least type 3 or 4, EN 14605) which is impermeable for the biocidal product
shall be worn (coverall material to be specified by the authorisation holder within the product
information);
— Eye protection;
— Substance/task appropriate respirator if ventilation is inadequate.
— Liquids used in textile and fiber processing fluids must not enter surface water directly. Use product only in
premises that are connected to a STP.
— Recirculating liquids in photoprocessing systems and fountain solution systems must not enter surface water
directly. Use product only in premises that are connected to a STP.
4.21.3. Where specific to the use, the particulars of likely direct or indirect effects, first aid instructions and emergency measures to
protect the environment
See general directions for use.
4.21.4. Where specific to the use, the instructions for safe disposal of the product and its packaging
See general directions for use.
4.21.5. Where specific to the use, the conditions of storage and shelf-life of the product under normal conditions of storage
See general directions for use.
4.22. Use description
Table 22.
Preservation of re-circulating liquids used in paint spray booths and electrodeposition coating systems
Product type PT11: Preservatives for liquid-cooling and processing systems
Where relevant, an exact description of -
the authorised use
Target organism(s) (including Scientific name: no data
development stage) Common name: Bacteria
Development stage: no data
Scientific name: no data
Common name: Yeasts
Development stage: no data
Field(s) of use indoor use
Preservation of re-circulating liquids used in paint spray booths and
electrodeposition coating systems.
146/227 ELI: http://data.europa.eu/eli/reg_impl/2025/2202/ojEN
OJ L, 20.11.2025
The biocidal product is used for preservation of fluids in pre-
treatment processes (Cleaning treatment for grease removal and soil,
degreasing Phosphating process, Rinse off tanks) paint spray booths
and electrodeposition coating systems (e.g. cataphoretic baths)
applied in Car Refinishing and Original equipment Car
Manufacturing to control the integrity of recirculating fluid by
reducing microbial contamination from bacteria and fungi in the
bulk solution.
Application method(s) Method: -
Detailed description:
-
Application rate(s) and frequency Application Rate:
Preventive treatment: 7,5 to 30 mg C(M)IT/MIT (3:1) per Kg final
product.
-
Number and timing of application:
Preventive treatment: 7,5 to 30 mg C(M)IT/MIT (3:1) per Kg final
product.
The biocidal product is added at the time of manufacture, storage or
shipment.
Category(ies) of users industrial
Pack sizes and packaging material For industrial and professional users:
— HDPE flask: 5 L (nominal)
— HDPE Pail / Jerrycan: 10 L, 20 L, 25 L, 30 L (nominal)
— Box with HDPE liner: 20 L
— HDPE Drum: 110 L, 120 L, 200 L, 260 L
— HDPE IBC: 650 L, 800 L, 1 000 L, 1 250 L
All products should be transport and stored in a vented room.
4.22.1. Use-specific instructions for use
Microbiological tests to prove adequacy of preservation have to be undertaken by the user of C(M)IT/MIT products
in order to determine the effective dose of the preservative for the specific matrix/location/system. If needed,
consult the manufacturer of the preservative product.
4.22.2. Use-specific risk mitigation measures
— Rinse the system (especially the dispensing pumps) with water prior to perform the cleaning step.
— During handling phases (mixing and loading) and cleaning of the dispensing pumps, exposure to the
product (corrosive and skin sensitizer product) has to be limited by use of PPE and application of technical
and organisational RMM:
— Minimisation of manual phases (process automation);
— Use of a dosing device;
— Regular cleaning of equipment and work area;
— Avoidance of contact with contaminated tools and objects;
— Good standard of general ventilation;
— Training and management of staff on good practice.
ELI: http://data.europa.eu/eli/reg_impl/2025/2202/oj 147/227EN
OJ L, 20.11.2025
— PPE is as follows:
— protective chemical resistant gloves (glove material to be specified by the authorisation holder within
the product information);
— protective coverall (at least type 3 or 4, EN 14605) which is impermeable for the biocidal product
shall be worn (coverall material to be specified by the authorisation holder within the product
information);
— Eye protection;
— Substance/task appropriate respirator if ventilation is inadequate.
4.22.3. Where specific to the use, the particulars of likely direct or indirect effects, first aid instructions and emergency measures to
protect the environment
See general directions for use.
4.22.4. Where specific to the use, the instructions for safe disposal of the product and its packaging
See general directions for use.
4.22.5. Where specific to the use, the conditions of storage and shelf-life of the product under normal conditions of storage
See general directions for use.
4.23. Use description
Table 23
Preservation of liquids used in closed recirculating heating systems and associated pipework
Product type PT11: Preservatives for liquid-cooling and processing systems
Where relevant, an exact description of -
the authorised use
Target organism(s) (including Scientific name: no data
development stage) Common name: Bacteria (anaerobes and aerobes (including
Legionella pneumophila)
Development stage: no data
Scientific name: no data
Common name: Yeasts
Development stage: no data
Scientific name: no data
Common name: fungi
Development stage: no data
Field(s) of use indoor use
outdoor use
Preservation of liquids used in closed recirculating heating systems
and associated pipework. Pre-commission biocide flushing of new or
existing pipework systems (heating and chilling pipework) includes
used or new structural pipework built on industrial building projects.
148/227 ELI: http://data.europa.eu/eli/reg_impl/2025/2202/ojEN
OJ L, 20.11.2025
Closed recirculating heating systems: pre-commission biocidal
product flushing of new or existing pipework systems (heating and
chilling pipework) includes used or new structural pipework built on
industrial building projects. The biocidal product is used to control
the growth of aerobic and anaerobic bacteria, fungi and biofilm in the
circulating water of closed systems. Closed systems are less
susceptible to corrosion, scaling and biological fouling than open
systems. However microbial problems can occur, if the system is left
filled and untreated. This is due to the presence of nitrite and glycols
used as nutrients by microbes.
Application method(s) Method: closed system
Detailed description:
Manual and automated dosing. The biocidal product is dosed
automatically in the heat transfer fluid, in a place of good mixing.
The feeding pipe must dose the biocidal product below the water
level in order to limit the evaporation of the biocidal product.
Application rate(s) and frequency Application Rate:
Curative treatment - against bacteria at 5 g C(M)IT/MIT (3:1) / m3 of
water (including L. pneumophila) - against biofilm at 14,9 g C(M)
IT/MIT (3:1) / m3 of water - against fungi and yeast at 1 g C(M)IT/MIT
/ m3 of water Preventive treatment - against bacteria (including L.
pneumophila) at 3 g C(M)IT/MIT (3:1) / m3 of water - against biofilm
at 3 g C(M)IT/MIT (3:1) / m3 of water.
-
Number and timing of application:
Curative treatment:
— against bacteria at 5 g C(M)IT/MIT (3:1) / m3 of water (including L.
pneumophila)
Contact time: 24 hours
— against biofilm at 14,9 g C(M)IT/MIT (3:1) / m3 of water
Contact time: 24 hours
— against fungi and yeast at 1 g C(M)IT/MIT / m3 of water Contact
time: 48 hours
Preventive treatment
— against bacteria (including L. pneumophila) at 3 g C(M)IT/MIT
(3:1) / m3 of water and against biofilm at 3 g C(M)IT/MIT (3:1) /
m3 of water.
Category(ies) of users industrial
Pack sizes and packaging material For industrial and professional users:
— HDPE flask: 5 L (nominal)
— HDPE Pail / Jerrycan: 10 L, 20 L, 25 L, 30 L (nominal)
— Box with HDPE liner: 20 L
— HDPE Drum: 110 L, 120 L, 200 L, 260 L
— HDPE IBC: 650 L, 800 L, 1 000 L, 1 250 L
All products should be transport and stored in a vented room.
ELI: http://data.europa.eu/eli/reg_impl/2025/2202/oj 149/227EN
OJ L, 20.11.2025
4.23.1. Use-specific instructions for use
Microbiological tests to prove adequacy of preservation have to be undertaken by the user of C(M)IT/MIT products
in order to determine the effective dose of the preservative for the specific matrix/location/system. If needed,
consult the manufacturer of the preservative product.
4.23.2. Use-specific risk mitigation measures
— Rinse the system (especially the dispensing pumps) with water prior to perform the cleaning step.
— During handling phases (mixing and loading) and cleaning of the dispensing pumps, exposure to the
product (corrosive and skin sensitizer product) has to be limited by use of PPE and application of technical
and organisational RMM:
— Minimisation of manual phases (process automation);
— Use of a dosing device;
— Regular cleaning of equipment and work area;
— Avoidance of contact with contaminated tools and objects;
— Good standard of general ventilation;
— Training and management of staff on good practice.
— PPE is as follows:
— protective chemical resistant gloves (glove material to be specified by the authorisation holder within
the product information);
— protective coverall (at least type 3 or 4, EN 14605) which is impermeable for the biocidal product
shall be worn (coverall material to be specified by the authorisation holder within the product
information);
— Eye protection;
— Substance/task appropriate respirator if ventilation is inadequate.
4.23.3. Where specific to the use, the particulars of likely direct or indirect effects, first aid instructions and emergency measures to
protect the environment
See general directions for use.
4.23.4. Where specific to the use, the instructions for safe disposal of the product and its packaging
See general directions for use.
4.23.5. Where specific to the use, the conditions of storage and shelf-life of the product under normal conditions of storage
See general directions for use.
150/227 ELI: http://data.europa.eu/eli/reg_impl/2025/2202/ojEN
OJ L, 20.11.2025
4.24. Use description
Table 24
Preservation of polymers used in oilfield processes (e.g. enhanced oil recovery, drilling muds, etc.)
Product type PT11: Preservatives for liquid-cooling and processing systems
Where relevant, an exact description of -
the authorised use
Target organism(s) (including Scientific name: no data
development stage) Common name: Bacteria
Development stage: no data
Field(s) of use outdoor use
Preservation of polymers used in oilfield processes (e.g. enhanced oil
recovery, drilling muds, etc.)
Application method(s) Method: -
Detailed description:
-
Application rate(s) and frequency Application Rate:
Preventive treatment of polymers used in the injection water:
Xanthan polymer: 30 -50 g C(M)IT/MIT/m3 solution. HPAM
polymer: 30 - 50 g C(M)IT/MIT/m3 solution. Preventive treatment of
polymers used in the drilling muds: Xanthan polymer: 30 g C(M)IT/
MIT/m3 solution. HPAM polymer: 30 g C(M)IT/MIT/m3 solution.
-
Number and timing of application:
Preventive treatment of polymers used in the injection water:
Xanthan polymer: 30 -50 g C(M)IT/MIT/m3 solution.
HPAM polymer: 30 - 50 g C(M)IT/MIT/m3 solution.
Preventive treatment of polymers used in the drilling muds:
Xanthan polymer: 30 g C(M)IT/MIT/m3 solution.
HPAM polymer: 30 g C(M)IT/MIT/m3 solution.
Category(ies) of users industrial
Pack sizes and packaging material For industrial and professional users:
— HDPE flask: 5 L (nominal)
— HDPE Pail / Jerrycan: 10 L, 20 L, 25 L, 30 L (nominal)
— Box with HDPE liner: 20 L
— HDPE Drum: 110 L, 120 L, 200 L, 260 L
— HDPE IBC: 650 L, 800 L, 1 000 L, 1 250 L
All products should be transport and stored in a vented room.
ELI: http://data.europa.eu/eli/reg_impl/2025/2202/oj 151/227EN
OJ L, 20.11.2025
4.24.1. Use-specific instructions for use
Microbiological tests to prove adequacy of preservation have to be undertaken by the user of C(M)IT/MIT products
in order to determine the effective dose of the preservative for the specific matrix/location/system. If needed,
consult the manufacturer of the preservative product.
4.24.2. Use-specific risk mitigation measures
— Rinse the system (especially the dispensing pumps) with water prior to perform the cleaning step.
— During handling phases (mixing and loading) and cleaning of the dispensing pumps, exposure to the
product (corrosive and skin sensitizer product) has to be limited by use of PPE and application of technical
and organisational RMM:
— Minimisation of manual phases (process automation);
— Use of a dosing device;
— Regular cleaning of equipment and work area;
— Avoidance of contact with contaminated tools and objects;
— Good standard of general ventilation;
— Training and management of staff on good practice.
— PPE is as follows:
— protective chemical resistant gloves (glove material to be specified by the authorisation holder within
the product information);
— protective coverall (at least type 3 or 4, EN 14605) which is impermeable for the biocidal product
shall be worn (coverall material to be specified by the authorisation holder within the product
information);
— Eye protection;
— Substance/task appropriate respirator if ventilation is inadequate.
4.24.3. Where specific to the use, the particulars of likely direct or indirect effects, first aid instructions and emergency measures to
protect the environment
See general directions for use.
4.24.4. Where specific to the use, the instructions for safe disposal of the product and its packaging
See general directions for use.
4.24.5. Where specific to the use, the conditions of storage and shelf-life of the product under normal conditions of storage
See general directions for use.
4.25. Use description
Table 25
Slimicide treatment in the de-inking process of the pulp and paper
Product type PT12: Slimicides
Where relevant, an exact description of -
the authorised use
152/227 ELI: http://data.europa.eu/eli/reg_impl/2025/2202/ojEN
OJ L, 20.11.2025
Target organism(s) (including Scientific name: no data
development stage) Common name: Bacteria
Development stage: no data
Scientific name: no data
Common name: Yeasts
Development stage: no data
Scientific name: no data
Common name: fungi
Development stage: no data
Field(s) of use indoor use
Slimicide treatment in the de-inking process of the pulp and paper.
Recycling paper /deinking paper mills. Deinking process is a
manufacturing paper process of removing printing inks from waste
paper-fibers to produce deinked pulp.
Application method(s) Method: closed system
Detailed description:
Manual and automated dosing. The biocidal product is automatically
dosed by pump and fixed pipes into the circuit, usually in the pulper
below the water level.
Application rate(s) and frequency Application Rate:
Curative treatment: 10 to 14,9 g C(M)IT/MIT (3:1) / m3 of water to
be treated. Preventive treatment: 5 g C(M)IT/MIT (3:1) / m3 of water
to be treated.
-
Number and timing of application:
Curative treatment: 10 to 14,9 g C(M)IT/MIT (3:1) / m3 of water to
be treated
Contact time: 24 hours
Preventive treatment: 5 g C(M)IT/MIT (3:1) / m3 of water to be
treated.
Category(ies) of users industrial
Pack sizes and packaging material For industrial and professional users:
— HDPE flask: 5 L (nominal)
— HDPE Pail / Jerrycan: 10 L, 20 L, 25 L, 30 L (nominal)
— Box with HDPE liner: 20 L
— HDPE Drum: 110 L, 120 L, 200 L, 260 L
— HDPE IBC: 650 L, 800 L, 1 000 L, 1 250 L
All products should be transport and stored in a vented room.
4.25.1. Use-specific instructions for use
Microbiological tests to prove adequacy of preservation have to be undertaken by the user of C(M)IT/MIT products
in order to determine the effective dose of the preservative for the specific matrix/location/system. If needed,
consult the manufacturer of the preservative product.
4.25.2. Use-specific risk mitigation measures
— Rinse the system (especially the dispensing pumps) with water prior to perform the cleaning step.
ELI: http://data.europa.eu/eli/reg_impl/2025/2202/oj 153/227EN
OJ L, 20.11.2025
— During handling phases (mixing and loading) and cleaning of the dispensing pumps, exposure to the
product (corrosive and skin sensitizer product) has to be limited by use of PPE and application of technical
and organisational RMM:
— Minimisation of manual phases (process automation);
— Use of a dosing device;
— Regular cleaning of equipment and work area;
— Avoidance of contact with contaminated tools and objects;
— Good standard of general ventilation;
— Training and management of staff on good practice.
— PPE is as follows:
— protective chemical resistant gloves (glove material to be specified by the authorisation holder within
the product information);
— protective coverall (at least type 3 or 4, EN 14605) which is impermeable for the biocidal product
shall be worn (coverall material to be specified by the authorisation holder within the product
information);
— Eye protection;
— Substance/task appropriate respirator if ventilation is inadequate.
4.25.3. Where specific to the use, the particulars of likely direct or indirect effects, first aid instructions and emergency measures to
protect the environment
See general directions for use.
4.25.4. Where specific to the use, the instructions for safe disposal of the product and its packaging
See general directions for use.
4.25.5. Where specific to the use, the conditions of storage and shelf-life of the product under normal conditions of storage
See general directions for use.
4.26. Use description
Table 26
Slimicide treatment in the wet-end stage of paper manufacturing process
Product type PT12: Slimicides
Where relevant, an exact description of -
the authorised use
Target organism(s) (including Scientific name: no data
development stage) Common name: Bacteria
Development stage: no data
Scientific name: no data
Common name: Yeasts
Development stage: no data
Scientific name: no data
Common name: fungi
Development stage: no data
154/227 ELI: http://data.europa.eu/eli/reg_impl/2025/2202/ojEN
OJ L, 20.11.2025
Field(s) of use indoor use
Slimicide treatment in the wet-end stage of the paper manufacturing
process (paper mills, wet-end stage (water circuits), and paper mills
process system).
Application method(s) Method: closed system
Detailed description:
Manual and automated dosing.
Application rate(s) and frequency Application Rate:
Curative treatment: 10 to 14,9 g C(M)IT/MIT (3:1) / m3 of water to
be treated. Preventive treatment: 5 g C(M)IT/MIT (3:1) / m3 of water
to be treated.
-
Number and timing of application:
Curative treatment: 10 to 14,9 g C(M)IT/MIT (3:1) / m3 of water to
be treated
Contact time: 24 hours
Preventive treatment: 5 g C(M)IT/MIT (3:1) / m3 of water to be
treated.
Category(ies) of users industrial
Pack sizes and packaging material For industrial and professional users:
— HDPE flask: 5 L (nominal)
— HDPE Pail / Jerrycan: 10 L, 20 L, 25 L, 30 L (nominal)
— Box with HDPE liner: 20 L
— HDPE Drum: 110 L, 120 L, 200 L, 260 L
— HDPE IBC: 650 L, 800 L, 1 000 L, 1 250 L
All products should be transport and stored in a vented room.
4.26.1. Use-specific instructions for use
Microbiological tests to prove adequacy of preservation have to be undertaken by the user of C(M)IT/MIT products
in order to determine the effective dose of the preservative for the specific matrix/location/system. If needed,
consult the manufacturer of the preservative product.
4.26.2. Use-specific risk mitigation measures
— Rinse the system (especially the dispensing pumps) with water prior to perform the cleaning step.
— During handling phases (mixing and loading) and cleaning of the dispensing pumps, exposure to the
product (corrosive and skin sensitizer product) has to be limited by use of PPE and application of technical
and organisational RMM:
— Minimisation of manual phases (process automation);
— Use of a dosing device;
— Regular cleaning of equipment and work area;
— Avoidance of contact with contaminated tools and objects;
— Good standard of general ventilation;
— Training and management of staff on good practice.
ELI: http://data.europa.eu/eli/reg_impl/2025/2202/oj 155/227EN
OJ L, 20.11.2025
— PPE is as follows:
— protective chemical resistant gloves (glove material to be specified by the authorisation holder within
the product information);
— protective coverall (at least type 3 or 4, EN 14605) which is impermeable for the biocidal product
shall be worn (coverall material to be specified by the authorisation holder within the product
information);
— Eye protection;
— Substance/task appropriate respirator if ventilation is inadequate.
— The use of C(M)IT/MIT (3:1) containing products for the slimicide treatment in the wet-end stage of the
paper manufacturing process is restricted to
(a) curative treatments in plants connected to a slimicide-free water from a pulp mill and only for the
treatment of the short circulation of the paper mill; and
(b) preventive treatments,
and, for both cases, only if the factory’s waste water is purified in an on-site (full) industrial sewage
treatment plant with a minimal capacity of 5 000 m3per day as described in the Industrial Emission
Directive 2010/75/EU (Best Available Techniques for the production of pulp, paper and board) and if
a dilution of at least 200 times in surface water is achieved after the industrial sewage treatment plant.
4.26.3. Where specific to the use, the particulars of likely direct or indirect effects, first aid instructions and emergency measures to
protect the environment
See general directions for use.
4.26.4. Where specific to the use, the instructions for safe disposal of the product and its packaging
See general directions for use.
4.26.5. Where specific to the use, the conditions of storage and shelf-life of the product under normal conditions of storage
See general directions for use.
4.27. Use description
Table 27
Preventive treatment (biofouling control) online and after cleaning in place for industrial RO/NF
membranes
Product type PT12: Slimicides
Where relevant, an exact description of -
the authorised use
Target organism(s) (including Scientific name: no data
development stage) Common name: Bacteria
Development stage: no data
Field(s) of use indoor use
Preventive treatment (biofouling control) online and after cleaning in
place for industrial RO/NF membranes
156/227 ELI: http://data.europa.eu/eli/reg_impl/2025/2202/ojEN
OJ L, 20.11.2025
Application method(s) Method: closed system
Detailed description:
Manual and automated dosing.Biocidal product application on a
routine basis will prevent biofilm growth on Reverse Osmosis or
Nano Filtration membrane surfaces, feed spacer, filter media and
pipework. The biocidal product should be dispensed to the feed water
at a point to assure adequate mixing throughout the system.
Application rate(s) and frequency Application Rate:
Preventive treatment: 5 g C(M)IT/MIT (3:1) per m3 of fluid
-
Number and timing of application:
Preventive treatment: 5 g C(M)IT/MIT (3:1) per m3 of fluid
Category(ies) of users industrial
Pack sizes and packaging material For industrial and professional users:
— HDPE flask: 5 L (nominal)
— HDPE Pail / Jerrycan: 10 L, 20 L, 25 L, 30 L (nominal)
— Box with HDPE liner: 20 L
— HDPE Drum: 110 L, 120 L, 200 L, 260 L
— HDPE IBC: 650 L, 800 L, 1 000 L, 1 250 L
All products should be transport and stored in a vented room.
4.27.1. Use-specific instructions for use
Microbiological tests to prove adequacy of preservation have to be undertaken by the user of C(M)IT/MIT products
in order to determine the effective dose of the preservative for the specific matrix/location/system. If needed,
consult the manufacturer of the preservative product.
4.27.2. Use-specific risk mitigation measures
— Rinse the system (especially the dispensing pumps) with water prior to perform the cleaning step.
— During handling phases (mixing and loading) and cleaning of the dispensing pumps, exposure to the
product (corrosive and skin sensitizer product) has to be limited by use of PPE and application of technical
and organisational RMM:
— Minimisation of manual phases (process automation);
— Use of a dosing device;
— Regular cleaning of equipment and work area;
— Avoidance of contact with contaminated tools and objects;
— Good standard of general ventilation;
— Training and management of staff on good practice.
— PPE is as follows:
— protective chemical resistant gloves (glove material to be specified by the authorisation holder within
the product information);
ELI: http://data.europa.eu/eli/reg_impl/2025/2202/oj 157/227EN
OJ L, 20.11.2025
— protective coverall (at least type 3 or 4, EN 14605) which is impermeable for the biocidal product
shall be worn (coverall material to be specified by the authorisation holder within the product
information);
— Eye protection;
— Substance/task appropriate respirator if ventilation is inadequate.
— Use product only in premises that are connected to a STP.
4.27.3. Where specific to the use, the particulars of likely direct or indirect effects, first aid instructions and emergency measures to
protect the environment
See general directions for use.
4.27.4. Where specific to the use, the instructions for safe disposal of the product and its packaging
See general directions for use.
4.27.5. Where specific to the use, the conditions of storage and shelf-life of the product under normal conditions of storage
See general directions for use.
4.28. Use description
Table 28
Products to control microbial deterioration in fluids used for working or cutting metal, glass or other
materials
Product type PT13: Working or cutting fluid preservatives
Where relevant, an exact description of -
the authorised use
Target organism(s) (including Scientific name: no data
development stage) Common name: Bacteria
Development stage: no data
Scientific name: no data
Common name: Yeasts
Development stage: no data
Scientific name: no data
Common name: fungi
Development stage: no data
Field(s) of use indoor use
Products to control microbial deterioration in fluids used for working
or cutting metal, glass or other materials
The biocidal product is recommended to control the growth of
bacteria and fungi in fluids used for metalworking fluids (cutting,
grinding, rolling, drawing, etc.) metal surface treatment (aqueous
multipurpose and de-watering rust cleaner fluids, etc.) and cutting
fluids for glass or other materials.
Application method(s) Method: -
Detailed description:
The biocidal product should be dispensed as a tankside additive into
the circulating use-dilution of the fluid, using a metering pump or by
manual pouring, at a point to assure adequate mixing throughout the
system.
158/227 ELI: http://data.europa.eu/eli/reg_impl/2025/2202/ojEN
OJ L, 20.11.2025
Application rate(s) and frequency Application Rate:
Curative treatment: When the system is noticeably fouled, apply
14,9 g C(M)IT/MIT (3:1) per m3 of fluid to be treated. Preventive
treatment: When control is obtained, adding 10 g C(M)IT/MIT (3:1)
per m3 of fluid to be treated.
-
Number and timing of application:
Curative treatment:
When the system is noticeably fouled, apply 14,9 g C(M)IT/MIT (3:1)
per m3 of fluid to be treated.
Contact time: 24h
Preventive treatment:
When control is obtained, adding 10 g C(M)IT/MIT (3:1) per m3 of
fluid to be treated.
Category(ies) of users industrial
Pack sizes and packaging material For industrial and professional users:
— HDPE flask: 5 L (nominal)
— HDPE Pail / Jerrycan: 10 L, 20 L, 25 L, 30 L (nominal)
— Box with HDPE liner: 20 L
— HDPE Drum: 110 L, 120 L, 200 L, 260 L
— HDPE IBC: 650 L, 800 L, 1 000 L, 1 250 L
All products should be transport and stored in a vented room.
4.28.1. Use-specific instructions for use
Microbiological tests to prove adequacy of preservation have to be undertaken by the user of C(M)IT/MIT products
in order to determine the effective dose of the preservative for the specific matrix/location/system. If needed,
consult the manufacturer of the preservative product.
4.28.2. Use-specific risk mitigation measures
— Rinse the system (especially the dispensing pumps) with water prior to perform the cleaning step.
— During handling phases (mixing and loading) and cleaning of the dispensing pumps, exposure to the
product (corrosive and skin sensitizer product) has to be limited by use of PPE and application of technical
and organisational RMM:
— Minimisation of manual phases (process automation);
— Use of a dosing device;
— Regular cleaning of equipment and work area;
— Avoidance of contact with contaminated tools and objects;
— Good standard of general ventilation;
— Training and management of staff on good practice.
— PPE is as follows:
— protective chemical resistant gloves (glove material to be specified by the authorisation holder within
the product information);
ELI: http://data.europa.eu/eli/reg_impl/2025/2202/oj 159/227EN
OJ L, 20.11.2025
— protective coverall (at least type 3 or 4, EN 14605) which is impermeable for the biocidal product
shall be worn (coverall material to be specified by the authorisation holder within the product
information);
— Eye protection;
— Substance/task appropriate respirator if ventilation is inadequate.
4.28.3. Where specific to the use, the particulars of likely direct or indirect effects, first aid instructions and emergency measures to
protect the environment
See general directions for use.
4.28.4. Where specific to the use, the instructions for safe disposal of the product and its packaging
See general directions for use.
4.28.5. Where specific to the use, the conditions of storage and shelf-life of the product under normal conditions of storage
See general directions for use.
5. GENERAL DIRECTIONS FOR USE OF THE META SPC 3
5.1. Instructions for use
— The duration of the effect is dependent on the performance requirements of the customer for their preserved
material and on the specific ingredients composition and pH of the preserved product.
— Always read the label or leaflet before use and follow all the instructions provided.
— Respect the conditions of use of the product (concentration, contact time, temperature, pH, etc.)
PRECAUTIONARY MEASURES DURING STORAGE AND TRANSPORT:
Keep in a well-ventilated place. The product as supplied may evolve gas (largely carbon dioxide) slowly. To prevent
the buildup of pressure the product is packaged in specially vented containers, where necessary. Keep this product
in the original container when not in use. Container must be stored and transported in an upright position to
prevent spilling the contents through the vent, where fitted.
5.2. Risk mitigation measures
-
5.3. Particulars of likely direct or indirect effects, first aid instructions and emergency measures to protect
the environment
— Skin contact: Remove contaminated clothing and shoes. Wash contaminated skin with water. Contact
poison treatment specialist if symptoms occur.
— Eye contact: Immediately flush with plenty of water, occasionally lifting the upper and lower eyelids. Check
for and remove any contact lenses if easy to do. Continue to rinse with tepid water for at least 30 minutes.
Call 112/ambulance for medical assistance.
— Ingestion: Wash out mouth with water. Contact poison treatment specialist. Seek medical advice
immediately if symptoms occur and/or large quantities have been ingested. Do not give fluids or induce
vomiting.
— Inhalation (of spray mist): Remove victim to fresh air and keep at rest in a position comfortable for
breathing. Seek medical advice immediately if symptoms occur and/or large quantities have been inhaled.
160/227 ELI: http://data.europa.eu/eli/reg_impl/2025/2202/ojEN
OJ L, 20.11.2025
— In case of impaired consciousness place in recovery position and seek medical advice immediately.
— Keep the container or label available.
5.4. Instructions for safe disposal of the product and its packaging
— Do not discharge unused product on the ground, into water courses, into pipes (e.g. sink, toilets) nor down
the drains.
— Dispose of unused product, its packaging and all other waste, in accordance with local regulations.
5.5. Conditions of storage and shelf-life of the product under normal conditions of storage
Conditions for safe storage, including any incompatibilities: Keep in a dry, cool and well-ventilated place, in the
original container.
Shelf-life: 12 months
Protect from sunlight.
Recommendation: If a metal packaging is used, a varnish layer should be applied.
6. OTHER INFORMATION
-
7. THIRD INFORMATION LEVEL: INDIVIDUAL PRODUCTS IN THE META SPC 3
7.1. Trade name(s), authorisation number and specific composition of each individual product
Trade name(s) KATHON™ CF Market area: EU
400 Biocide
Dab 4228 Market area: EU
BAL 400BI Market area: EU
Biocide 400 Market area: EU
Biotech 400 Market area: EU
Biocide KT400 Market area: EU
BioCheck Market area: EU
KT400
KT400 Market area: EU
C 412 TT Market area: EU
Dab 4228 Market area: EU
Deep Bio® Market area: EU
400
Ecosafe Bio Market area: EU
400
Filtralga ME Market area: EU
Filtralga 9550 Market area: EU
ELI: http://data.europa.eu/eli/reg_impl/2025/2202/oj 161/227EN
OJ L, 20.11.2025
PH-SB400 Market area: EU
Helamin Market area: EU
BZ9550
Isotreat 400 Market area: EU
OS Isobio4 Market area: EU
Odysside B Market area: EU
330
Relvamine Market area: EU
BIOC
Sayvol Bio Market area: EU
LP400
Authorisation number EU-0025449-0004 1-3
Common name IUPAC name Function CAS number EC number Content (%)
C(M)IT/MIT Reaction mass Active substance 55965-84-9 5,9 % (w/w)
(3:1) of 5-chloro-
2-methyl-2h-
isothiazol-
3-one
and 2-methyl-
2h-isothiazol-
3-one (3:1)
7.2. Trade name(s), authorisation number and specific composition of each individual product
Trade name(s) KATHON™CF Market area: EU
210 BIOCIDE
BAL 210BI Market area: EU
BioCheck Market area: EU
KT210
Biocide KT210 Market area: EU
Biocide 210 Market area: EU
Biotech 210 Market area: EU
B203-210 Market area: EU
Deep Bio® Market area: EU
210
Ecosafe Bio Market area: EU
210
Filtralga Market area: EU
ME-15
162/227 ELI: http://data.europa.eu/eli/reg_impl/2025/2202/ojEN
OJ L, 20.11.2025
KT210 Market area: EU
Isotreat 210 Market area: EU
MIRECIDE- Market area: EU
M/86
MK3203 Market area: EU
MK3094 Market area: EU
MK3394 Market area: EU
OS Isobio 210 Market area: EU
Odysside B Market area: EU
330M
PH-SB210 Market area: EU
STENCO B-85 Market area: EU
Sayvol Bio Market area: EU
LP210
TECNA 520 Market area: EU
Authorisation number EU-0025449-0005 1-3
Common name IUPAC name Function CAS number EC number Content (%)
C(M)IT/MIT Reaction mass Active substance 55965-84-9 3,2 % (w/w)
(3:1) of 5-chloro-
2-methyl-2h-
isothiazol-
3-one
and 2-methyl-
2h-isothiazol-
3-one (3:1)
7.3. Trade name(s), authorisation number and specific composition of each individual product
Trade name(s) KATHON™W­ Market area: EU
T 210
BIOCIDE
A-CID SA Market area: EU
ADUR 166 Market area: EU
ALG 200 Market area: EU
Biocide BALK Market area: EU
20
Biocide Market area: EU
KT210WT
ELI: http://data.europa.eu/eli/reg_impl/2025/2202/oj 163/227EN
OJ L, 20.11.2025
France Algue Market area: EU
242
KL60 TA21 Market area: EU
KT210WT Market area: EU
MK3094 Market area: EU
MK3394 Market area: EU
MK3203 Market area: EU
B203-210WT Market area: EU
Biocide Market area: EU
210WT
Biotech Market area: EU
210WT
Deep Bio® Market area: EU
210WT
Ecosafe Bio Market area: EU
210WT
OS Isobio Market area: EU
210WT
PH-SB210WT Market area: EU
Sayvol Bio Market area: EU
LP210WT
Authorisation number EU-0025449-0006 1-3
Common name IUPAC name Function CAS number EC number Content (%)
C(M)IT/MIT Reaction mass Active substance 55965-84-9 3,2 % (w/w)
(3:1) of 5-chloro-
2-methyl-2h-
isothiazol-
3-one
and 2-methyl-
2h-isothiazol-
3-one (3:1)
7.4. Trade name(s), authorisation number and specific composition of each individual product
Trade name(s) KATHON™ Market area: EU
WTE BIOCIDE
KATHON™ Market area: EU
WTE
KATHON™ Market area: EU
LXE BIOCIDE
164/227 ELI: http://data.europa.eu/eli/reg_impl/2025/2202/ojEN
OJ L, 20.11.2025
KATHON™ Market area: EU
LXE
KATHON™ Market area: EU
MWE
BIOCIDE
Bansan 150 Market area: EU
Biocide Market area: EU
KT200LX
Biocide Market area: EU
KT200WT
Biocide Market area: EU
KT200MW
Biocide Market area: EU
515WTE
Biocide Market area: EU
515 MW
Biotech Market area: EU
103WTE
BioCheck Market area: EU
WTE
BioCheck KT Market area: EU
MW
Biocheck WB Market area: EU
Biocheck 3103 Market area: EU
Biotech Market area: EU
103MW
BIOMATE Market area: EU
SAN9363
BIO 417 Market area: EU
B203WTE Market area: EU
B203MW Market area: EU
C 412 TTE Market area: EU
Deep Bio® Market area: EU
20MW
Deep Bio® Market area: EU
20WTE
Ecosafe Bio Market area: EU
WTE
Ecosafe Bio Market area: EU
MW
ELI: http://data.europa.eu/eli/reg_impl/2025/2202/oj 165/227EN
OJ L, 20.11.2025
Hydrex™ Market area: EU
7310
Isotreat WTE Market area: EU
KT200LX Market area: EU
KT200WT Market area: EU
KT200MW Market area: EU
MIRECIDE- Market area: EU
M/87
Novocide 10 C Market area: EU
OBBIO210 Market area: EU
OS Isobio Market area: EU
1.5WTE
Pastosept K Market area: EU
PH-SB102WTE Market area: EU
PH-SB102MW Market area: EU
PS 2175 Market area: EU
SAN Market area: EU
ADDITIVE
SANY POOL Market area: EU
Sayvol Bio Market area: EU
WTE
Sayvol Bio LP Market area: EU
MW
Wacozid 3150 Market area: EU
OS Isobio Market area: EU
1.5MW
BAC-S Market area: EU
Biocide BAL Market area: EU
GX
Biocide BAL Market area: EU
P10
Biocide BALK Market area: EU
10
biocil-I Market area: EU
BIOMATE Market area: EU
MBC781
France Algue Market area: EU
222
166/227 ELI: http://data.europa.eu/eli/reg_impl/2025/2202/ojEN
OJ L, 20.11.2025
GEWA B 352 Market area: EU
HCT-B-71 Market area: EU
O’RIZON 415 Market area: EU
rascal-B-71 Market area: EU
WANSON Market area: EU
W23L
watERTreat Market area: EU
BIO253 B
Authorisation number EU-0025449-0007 1-3
Common name IUPAC name Function CAS number EC number Content (%)
C(M)IT/MIT Reaction mass Active substance 55965-84-9 2,3 % (w/w)
(3:1) of 5-chloro-
2-methyl-2h-
isothiazol-
3-one
and 2-methyl-
2h-isothiazol-
3-one (3:1)
7.5. Trade name(s), authorisation number and specific composition of each individual product
Trade name(s) KATHON™ CF Market area: EU
150 Biocide
KATHON™ Market area: EU
CF-150
Biocide
KATHON™ Market area: EU
CF-150
AAHS BI Market area: EU
ACN Green Market area: EU
Line 802
AQ 616 Market area: EU
AQF 415 Market area: EU
AQUATREAT Market area: EU
415
ATN JB48 Market area: EU
BAL 200BI Market area: EU
ELI: http://data.europa.eu/eli/reg_impl/2025/2202/oj 167/227EN
OJ L, 20.11.2025
Bewacid B 728 Market area: EU
Biocheck WB Market area: EU
CF
Biocheck 3103 Market area: EU
CF
Biocide 515 Market area: EU
Biocide KT200 Market area: EU
BioCheck KT Market area: EU
BIOCONTROL Market area: EU
5
BIOMATE Market area: EU
MBC781E
BiopleX TZ Market area: EU
150
Bio-Safe Market area: EU
KT200
Biotech 103 Market area: EU
B203 Market area: EU
BW 415 Market area: EU
BS4005A Market area: EU
Busan 1078 Market area: EU
Butrol 1078 Market area: EU
Bulab 8862 Market area: EU
Bulab 6057 Market area: EU
Carillion ITA Market area: EU
Certi-KT200 Market area: EU
CH32 Market area: EU
ComChem Bio Market area: EU
ITA
Dab 448 Market area: EU
Deep Bio® 20 Market area: EU
DIABICIDE Market area: EU
90 A
DIPOLIQUE Market area: EU
156
168/227 ELI: http://data.europa.eu/eli/reg_impl/2025/2202/ojEN
OJ L, 20.11.2025
Ecoral 1015 Market area: EU
Ecosafe Bio Market area: EU
WT
Ekobio-5 Market area: EU
ES515 Market area: EU
FINEALGUA Market area: EU
ME
GE32 Market area: EU
Hydrex™ Market area: EU
7943
HCS B32 Market area: EU
In-Boi Market area: EU
Isocil® Ultra Market area: EU
1.5
Isotreat Market area: EU
IWT KT200 Market area: EU
KT200 Market area: EU
Lubron BD Market area: EU
100
Lubron BD Market area: EU
110
Lubron BD Market area: EU
120
MB 215 Market area: EU
Mikrobizid M Market area: EU
24
MIRECIDE- Market area: EU
KW/600
MIRECIDE- Market area: EU
KW/600.X
Novocide 10 Market area: EU
Novo Cide 10 Market area: EU
NW515 Market area: EU
OS Isobio 1.5 Market area: EU
PA32 Market area: EU
PH-SB102 Market area: EU
PS 2176 Market area: EU
ELI: http://data.europa.eu/eli/reg_impl/2025/2202/oj 169/227EN
OJ L, 20.11.2025
QUIPROISO Market area: EU
LG
RAL200 Market area: EU
Relcide 310 Market area: EU
Sayvol Bio LP Market area: EU
ST202 Market area: EU
Starcide Ultra Market area: EU
1.5
Swiftclean BI Market area: EU
UPINZOL -10 Market area: EU
Wacozid 3150 Market area: EU
Wacozid 3150 Market area: EU
CF
Watercare Market area: EU
WHM KT200
“hygel“ KW 60 Market area: EU
B
BioCheck Market area: EU
KT200
Authorisation number EU-0025449-0008 1-3
Common name IUPAC name Function CAS number EC number Content (%)
C(M)IT/MIT Reaction mass Active substance 55965-84-9 2,3 % (w/w)
(3:1) of 5-chloro-
2-methyl-2h-
isothiazol-
3-one
and 2-methyl-
2h-isothiazol-
3-one (3:1)
7.6. Trade name(s), authorisation number and specific composition of each individual product
Trade name(s) KATHON™ Market area: EU
CG/ICP
Biocide
KATHON™ Market area: EU
CG-ICP
170/227 ELI: http://data.europa.eu/eli/reg_impl/2025/2202/ojEN
OJ L, 20.11.2025
KATHON™ Market area: EU
CG/ICP
Preservative
KATHON™ Market area: EU
MK Biocide
Biocide Market area: EU
KT200ICP
Biogat CG ICP Market area: EU
Isocil® HP 1.5 Market area: EU
MIRECIDE- Market area: EU
KW/24
Authorisation number EU-0025449-0009 1-3
Common name IUPAC name Function CAS number EC number Content (%)
C(M)IT/MIT Reaction mass Active substance 55965-84-9 2,2 % (w/w)
(3:1) of 5-chloro-
2-methyl-2h-
isothiazol-
3-one
and 2-methyl-
2h-isothiazol-
3-one (3:1)
7.7. Trade name(s), authorisation number and specific composition of each individual product
Trade name(s) KATHON™ Market area: EU
CG/ICPII
Biocide
Authorisation number EU-0025449-0010 1-3
Common name IUPAC name Function CAS number EC number Content (%)
C(M)IT/MIT Reaction mass Active substance 55965-84-9 2,2 % (w/w)
(3:1) of 5-chloro-
2-methyl-2h-
isothiazol-
3-one
and 2-methyl-
2h-isothiazol-
3-one (3:1)
ELI: http://data.europa.eu/eli/reg_impl/2025/2202/oj 171/227EN
OJ L, 20.11.2025
7.8. Trade name(s), authorisation number and specific composition of each individual product
Trade name(s) KATHON™ Market area: EU
CL 150
Biocide
SPECTRUS Market area: EU
NX1164
Authorisation number EU-0025449-0011 1-3
Common name IUPAC name Function CAS number EC number Content (%)
C(M)IT/MIT Reaction mass Active substance 55965-84-9 2,2 % (w/w)
(3:1) of 5-chloro-
2-methyl-2h-
isothiazol-
3-one
and 2-methyl-
2h-isothiazol-
3-one (3:1)
1. META SPC 4 ADMINISTRATIVE INFORMATION
1.1. Meta SPC 4 identifier
Identifier Meta SPC: meta-SPC 4 KATHON 1.5-3.5 Na
1.2. Suffix to the authorisation number
Number 1-4
1.3. Product type(s)
Product type(s) PT02: Disinfectants and algaecides not intended for direct
application to humans or animals
PT04: Food and feed area
PT06: Preservatives for products during storage
PT11: Preservatives for liquid-cooling and processing systems
PT12: Slimicides
172/227 ELI: http://data.europa.eu/eli/reg_impl/2025/2202/ojEN
OJ L, 20.11.2025
2. META SPC 4 COMPOSITION
2.1. Qualitative and quantitative information on the composition of the meta SPC 4
Common name IUPAC name Function CAS number EC number Content (%)
C(M)IT/MIT (3:1) Reaction mass Active 55965-84-9 2,2 - 5,1 % (w/w)
of 5-chloro- substance
2-methyl-2h-
isothiazol-
3-one
and 2-methyl-
2h-isothiazol-
3-one (3:1)
2.2. Type(s) of formulation of the meta SPC 4
Formulation type(s) AL Any other liquid
3. HAZARD AND PRECAUTIONARY STATEMENTS OF THE META SPC 4
Hazard statements H332: Harmful if inhaled.
H314: Causes severe skin burns and eye damage.
H317: May cause an allergic skin reaction.
H410: Very toxic to aquatic life with long lasting effects.
H302: Harmful if swallowed.
EUH071: Corrosive to the respiratory tract.
Precautionary statements P260: Do not breathe fume.
P264: Wash skin thoroughly after handling.
P270: Do not eat, drink or smoke when using this product.
P272: Contaminated work clothing should not be allowed
out of the workplace.
P273: Avoid release to the environment.
P280: Wear protective gloves/ protective clothing/ eye
protection/ face protection/ hearing protection .
P362+P364: Take off contaminated clothing and wash it
before reuse.
P333+P313: If skin irritation or rash occurs: Get medical
advice.
P301+P330+P331: IF SWALLOWED: rinse mouth. Do NOT
induce vomiting.
P303+P361+P353: IF ON SKIN (or hair): Take off immediately
all contaminated clothing. Rinse skin with water [or shower].
P304+P340: IF INHALED: Remove person to fresh air and
keep comfortable for breathing.
ELI: http://data.europa.eu/eli/reg_impl/2025/2202/oj 173/227EN
OJ L, 20.11.2025
P310: Immediately call a POISON CENTER/ doctor .
P305+P351+P338: IF IN EYES: Rinse cautiously with water for
several minutes. Remove contact lenses, if present and easy to
do. Continue rinsing.
P391: Collect spillage.
P405: Store locked up.
P301+P312: IF SWALLOWED: Call a POISON CENTER/ doctor if
you feel unwell.
4. AUTHORISED USE(S) OF THE META SPC
4.1. Use description
Table 1
Preservation of sump water in air conditioning and air washer systems.
Product type PT02: Disinfectants and algaecides not intended for direct application
to humans or animals
Where relevant, an exact description of -
the authorised use
Target organism(s) (including Scientific name: no data
development stage) Common name: Bacteria (including Legionella pneumophila)
Development stage: no data
Scientific name: no data
Common name: Yeasts
Development stage: no data
Scientific name: no data
Common name: fungi
Development stage: no data
Scientific name: no data
Common name: algae
Development stage: no data
Field(s) of use outdoor use
Preservation of sump water in air conditioning and air washer
systems.
Air conditioning systems and in air washer systems to preserve the
sump water. Air washer systems are used extensively in textile
factories and in the tobacco industry to scrub or clean the air and for
fine control of temperature and humidity.
Application method(s) Method: Open and closed Systems
Detailed description:
Automatic and Manual Dosing The biocidal product is typically
added in a central chilled water sump which supplies several air
washers. The loading process may be conducted either manually or
by automation. In the automated process, the biocide is metered
directly into the sump from a holding tank or other type of bulk
container by a dosimeter (pump). The feeding pipe must dose the
biocidal product below the water level in order to limit its
evaporation.
174/227 ELI: http://data.europa.eu/eli/reg_impl/2025/2202/ojEN
OJ L, 20.11.2025
Application rate(s) and frequency Application Rate:
Curative application: Bacteria, yeasts and fungi. When the system is
noticeably fouled, apply 5 to 14,9 mg C(M)IT/MIT (3:1) per Litre of
water to be treated, as post treatment after a shock dose of minimum
0,3 ppm of free chlorine. Preventive application: algae When control
is obtained, add a continuous or semi continuous feed of 3 to 5 mg
C(M)IT/MIT (3:1) per L of water to be treated
-
Number and timing of application:
Curative application: Bacteria, yeasts and fungi
When the system is noticeably fouled, apply 5 to 14,9 mg C(M)
IT/MIT (3:1) per Litre of water to be treated, as post treatment after a
shock dose of minimum 0,3 ppm of free chlorine.
Contact time of 1 hour.
Preventive application: algae
When control is obtained, add a continuous or semi continuous feed
of 3 to 5 mg C(M)IT/MIT (3:1) per L of water to be treated.
Regardless of the manner of treatment, the total concentration of the
active ingredient C(M)IT/MIT (3:1) in the system should not exceed
14,9 mg/L in the sump water.
Preliminary steps prior to addition:
The biocidal product is automatically dosed to the system. Manual
handling is necessary for the loading of the biocidal product into the
dosing systems.
Application Frequency:
Nominally every 2 to 3 days or as needed to obtain control. Repeat
until fouling is reduced to an acceptable level for controlling the
microbial growth.
Category(ies) of users industrial
Pack sizes and packaging material For industrial and professional users:
— HDPE flask: 5 L (nominal)
— HDPE Pail / Jerrycan: 10 L, 20 L, 25 L, 30 L (nominal)
— Box with HDPE liner: 20 L
— HDPE Drum: 110 L, 120 L, 200 L, 260 L
— HDPE IBC: 650 L, 800 L, 1 000 L, 1 250 L
All products should be transport and stored in a vented room.
4.1.1. Use-specific instructions for use
— Respect the conditions of use of the product (concentration, contact time, temperature, pH, etc.).
— The CMIT/MIT biocidal products are used after a shock dose of free chlorine in this application as
standard industry practice.
4.1.2. Use-specific risk mitigation measures
— Rinse the system (especially the dispensing pumps) with water prior to perform the cleaning step.
— During mixing and loading and cleaning of the dispensing pumps, exposure to the product (corrosive and
skin sensitizer product) has to be limited by use of PPE and application of technical and organisational RMM:
— Minimisation of manual phases (process automation);
— Use of a dosing device;
ELI: http://data.europa.eu/eli/reg_impl/2025/2202/oj 175/227EN
OJ L, 20.11.2025
— Regular cleaning of equipment and work area;
— Avoidance of contact with contaminated tools and objects;
— Good standard of general ventilation;
— Training and management of staff on good practice.
— PPE is as follows:
— protective chemical resistant gloves (glove material to be specified by the authorisation holder within
the product information);
— protective coverall (at least type 3 or 4, EN 14605) which is impermeable for the biocidal product
shall be worn (coverall material to be specified by the authorisation holder within the product
information);
— Eye protection;
— Substance/task appropriate respirator if ventilation is inadequate.
4.1.3. Where specific to the use, the particulars of likely direct or indirect effects, first aid instructions and emergency measures to
protect the environment
See general directions for use.
4.1.4. Where specific to the use, the instructions for safe disposal of the product and its packaging
See general directions for use.
4.1.5. Where specific to the use, the conditions of storage and shelf-life of the product under normal conditions of storage
See general directions for use.
4.2. Use description
Table 2
Preservation of fluids in conveyor belts and pasteurisers
Product type PT04: Food and feed area
Where relevant, an exact description of -
the authorised use
Target organism(s) (including Scientific name: no data
development stage) Common name: Bacteria
Development stage: no data
Scientific name: no data
Common name: Yeasts
Development stage: no data
Scientific name: no data
Common name: fungi
Development stage: no data
176/227 ELI: http://data.europa.eu/eli/reg_impl/2025/2202/ojEN
OJ L, 20.11.2025
Field(s) of use indoor use
Preservation of fluids in conveyor belts and pasteurisers
The biocidal product is used for the preservation of process fluids in
pasteurisers and conveyor belts used in food industry. The biocidal
product is used in these systems to either control or kill bacteria and
fungi.
Application method(s) Method: closed system
Detailed description:
Automated dosing The biocidal product is dosed automatically in the
heat transfer fluid, in a place of good mixing (e.g. collecting sump
below the conveyor belt).
Application rate(s) and frequency Application Rate:
Curative application: Bacteria, yeasts and fungi When the system is
noticeably fouled, apply 10 to 14,9 g C(M)IT/MIT (3:1) per m3 of
water to be treated as post treatment after a shock dose of minimum
0,3 ppm of free chlorine Preventive application: Bacteria: When
control is obtained, add a continuous or semi continuous feed of 2,5
to 5 g C(M)IT/MIT (3:1) per m3 of water to be treated.
-
Number and timing of application:
Curative application: Bacteria, yeasts and fungi
When the system is noticeably fouled, apply 10 to 14,9 g C(M)IT/MIT
(3:1) per m3 of water to be treated as post treatment after a shock
dose of minimum 0,3 ppm of free chlorine.
Contact time of 1 hour.
Preventive application: Bacteria:
When control is obtained, add a continuous or semi continuous feed
of 2,5 to 5 g C(M)IT/MIT (3:1) per m3 of water to be treated.
Preliminary steps prior to addition:
The biocidal product is automatically dosed to system. Manual
handling is necessary for the loading of containers containing the
biocidal product into the dosing systems.
Application Frequency:
Nominally every 2 to 3 days or as needed to obtain control. Repeat
until fouling is reduced to an acceptable level for controlling the
microbial growth.
Category(ies) of users industrial
Pack sizes and packaging material For industrial and professional users:
— HDPE flask: 5 L (nominal)
— HDPE Pail / Jerrycan: 10 L, 20 L, 25 L, 30 L (nominal)
— Box with HDPE liner: 20 L
— HDPE Drum: 110 L, 120 L, 200 L, 260 L
— HDPE IBC: 650 L, 800 L, 1 000 L, 1 250 L
All products should be transport and stored in a vented room.
ELI: http://data.europa.eu/eli/reg_impl/2025/2202/oj 177/227EN
OJ L, 20.11.2025
4.2.1. Use-specific instructions for use
— Respect the conditions of use of the product (concentration, contact time, temperature, pH, etc.).
— The CMIT/MIT biocidal products are used after a shock dose of free chlorine in this application as standard
industry practice.
4.2.2. Use-specific risk mitigation measures
— Rinse the system (especially the dispensing pumps) with water prior to perform the cleaning step.
— During mixing and loading and cleaning of the dispensing pumps, exposure to the product (corrosive and
skin sensitizer product) has to be limited by use of PPE and application of technical and organisational RMM:
— Minimisation of manual phases (process automation);
— Use of a dosing device;
— Regular cleaning of equipment and work area;
— Avoidance of contact with contaminated tools and objects;
— Good standard of general ventilation;
— Training and management of staff on good practice.
— PPE is as follows:
— protective chemical resistant gloves (glove material to be specified by the authorisation holder within
the product information);
— protective coverall (at least type 3 or 4, EN 14605) which is impermeable for the biocidal product
shall be worn (coverall material to be specified by the authorisation holder within the product
information);
— Eye protection;
— Substance/task appropriate respirator if ventilation is inadequate.
4.2.3. Where specific to the use, the particulars of likely direct or indirect effects, first aid instructions and emergency measures to
protect the environment
See general directions for use.
4.2.4. Where specific to the use, the instructions for safe disposal of the product and its packaging
See general directions for use.
4.2.5. Where specific to the use, the conditions of storage and shelf-life of the product under normal conditions of storage
See general directions for use.
4.3. Use description
Table 3
Long term offline preservation of reverse osmosis membranes used in potable water
Product type PT04: Food and feed area
Where relevant, an exact description of -
the authorised use
178/227 ELI: http://data.europa.eu/eli/reg_impl/2025/2202/ojEN
OJ L, 20.11.2025
Target organism(s) (including Scientific name: no data
development stage) Common name: Bacteria
Development stage: no data
Field(s) of use indoor use
Long term offline preservation of reverse osmosis membranes used
in potable water
The C(M)IT/MIT (3:1) biocidal product is recommended for
controlling biological growth in off-line trains reverse osmosis
membranes producing potable water for extended periods of time.
Application method(s) Method: closed system
Detailed description:
Manual and automated dosing. It is recommended that fouled
membranes be cleaned prior to shut-down and preservation. Please
refer to RO /NF supplier manual for membrane cleaning and system
shutdown procedures. The biocidal product should be dispensed as a
tankside additive into the circulating use-dilution of the fluid, using a
metering pump or by manual pouring, at a point to assure adequate
mixing throughout the system. After complete filling of the trains
RO/NF systems with the biocide solution, pumps are stopped (Off
line treatment) for extended periods of time. Typically C(M)IT/MIT
(3:1) solutions are prepared in the CIP (cleaning in place) tank and
added via the dosing system. Dilution with the permeate water or
high quality water is recommended for the preparation of the biocide
solution. Membranes should be soaked in the biocide solution during
the shut-down period.
Application rate(s) and frequency Application Rate:
7,5 -20 g of C(M)IT/MIT (3:1)/ m3 of water
-
Number and timing of application:
7,5 -20 g of C(M)IT/MIT (3:1)/ m3 of water
Category(ies) of users industrial
Pack sizes and packaging material For industrial and professional users:
— HDPE flask: 5 L (nominal)
— HDPE Pail / Jerrycan: 10 L, 20 L, 25 L, 30 L (nominal)
— Box with HDPE liner: 20 L
— HDPE Drum: 110 L, 120 L, 200 L, 260 L
— HDPE IBC: 650 L, 800 L, 1 000 L, 1 250 L
All products should be transport and stored in a vented room.
4.3.1. Use-specific instructions for use
— Respect the conditions of use of the product (concentration, contact time, temperature, pH, etc.).
— Prior to taking the membranes back on-line, flush carefully the elements with permeate water in order to
eliminate all the residual biocidal product.
ELI: http://data.europa.eu/eli/reg_impl/2025/2202/oj 179/227EN
OJ L, 20.11.2025
4.3.2. Use-specific risk mitigation measures
— Rinse the system (especially the dispensing pumps) with water prior to perform the cleaning step.
— During mixing and loading and cleaning of the whole system, exposure to the product (corrosive and skin
sensitizer product) has to be limited by use of PPE and application of technical and organisational RMM:
— Minimisation of manual phases (process automation);
— Use of a dosing device;
— Regular cleaning of equipment and work area;
— Avoidance of contact with contaminated tools and objects;
— Good standard of general ventilation;
— Training and management of staff on good practice.
— PPE is as follows:
— protective chemical resistant gloves (glove material to be specified by the authorisation holder within
the product information);
— protective coverall (at least type 3 or 4, EN 14605) which is impermeable for the biocidal product
shall be worn (coverall material to be specified by the authorisation holder within the product
information);
— Eye protection;
— Substance/task appropriate respirator if ventilation is inadequate.
4.3.3. Where specific to the use, the particulars of likely direct or indirect effects, first aid instructions and emergency measures to
protect the environment
See general directions for use.
4.3.4. Where specific to the use, the instructions for safe disposal of the product and its packaging
See general directions for use.
4.3.5. Where specific to the use, the conditions of storage and shelf-life of the product under normal conditions of storage
See general directions for use.
4.4. Use description
Table 4
Preservation of paints and coatings
Product type PT06: Preservatives for products during storage
Where relevant, an exact description of -
the authorised use
Target organism(s) (including Scientific name: no data
development stage) Common name: Bacteria
Development stage: no data
Scientific name: no data
Common name: Yeasts
Development stage: no data
Field(s) of use indoor use
outdoor use
Preservation of paints and coatings (including electrodeposition)
180/227 ELI: http://data.europa.eu/eli/reg_impl/2025/2202/ojEN
OJ L, 20.11.2025
The biocidal product is recommended to control the growth of
bacteria and yeasts in coatings applied by an electrodeposition
process and associated rinse systems and in water-based paints and
coatings in storage containers before use.
Application method(s) Method: closed system
Detailed description:
Manual and automated dosing. The biocidal product should be
dispensed as a tankside additive into the fluid, using a metering pump
or by manual pouring, at a point to assure adequate mixing
throughout the system.
Application rate(s) and frequency Application Rate:
Industrial uses: 1,5 - 14,5 % C(M)IT/MIT in the biocidal products;
Professional paints and general public paints: 7,5-14,9 mg/kg C(M)
IT/MIT (3:1) in final product.
-
Number and timing of application:
The biocidal product is added at the time of manufacture, storage or
shipment.
Industrial uses:
1,5 - 14,5 % C(M)IT/MIT in the biocidal products.
Professional paints and general public paints:
7,5-14,9 mg/kg C(M)IT/MIT (3:1) in final product.
For the biocidal product as supplied: for industrial use only.
Category(ies) of users industrial
Pack sizes and packaging material For industrial and professional users:
— HDPE flask: 5 L (nominal)
— HDPE Pail / Jerrycan: 10 L, 20 L, 25 L, 30 L (nominal)
— Box with HDPE liner: 20 L
— HDPE Drum: 110 L, 120 L, 200 L, 260 L
— HDPE IBC: 650 L, 800 L, 1 000 L, 1 250 L
All products should be transport and stored in a vented room.
4.4.1. Use-specific instructions for use
— The preservative can be added at any stage of the production of the product.
— Earliest possible addition is recommended for optimal protection.
— Consult the manufacturer to determine the optimal dosage for the various products to be preserved.
— It is recommended that the optimum biocide concentration and compatibility with individual formulations
is determined by means of laboratory tests.
— The duration and storage conditions of the preserved matrices may impact the efficacy of the product,
microbiological tests should be conducted to determine the appropriate application rate without exceeding
the maximum authorised application rate.
— The biocidal product shall be used for treatment of products (articles/mixtures) distributed to professional
users and to the general public.
ELI: http://data.europa.eu/eli/reg_impl/2025/2202/oj 181/227EN
OJ L, 20.11.2025
4.4.2. Use-specific risk mitigation measures
— During handling phases of products from Meta SPC 1, 2, 3 and 4 (Mixing and Loading), exposure to the
product (corrosive and skin sensitizer products) has to be limited by use of PPE and application of technical
and organisational RMM:
— Minimisation of manual phases (process automation);
— Use of a dosing device;
— Regular cleaning of equipment and work area;
— Avoidance of contact with contaminated tools and objects;
— Good standard of general ventilation;
— Training and management of staff on good practice.
— PPE is as follows:
— protective chemical resistant gloves (glove material to be specified by the authorisation holder within
the product information);
— protective coverall (at least type 3 or 4, EN 14605) which is impermeable for the biocidal product
shall be worn (coverall material to be specified by the authorisation holder within the product
information);
— Eye protection;
— Substance/task appropriate respirator if ventilation is inadequate.
— The maximal concentration of products from Meta SPC 1, 2, 3 and 4 to be added in paints used must be
below the threshold value of 15 ppm.
4.4.3. Where specific to the use, the particulars of likely direct or indirect effects, first aid instructions and emergency measures to
protect the environment
See general directions for use.
4.4.4. Where specific to the use, the instructions for safe disposal of the product and its packaging
See general directions for use.
4.4.5. Where specific to the use, the conditions of storage and shelf-life of the product under normal conditions of storage
See general directions for use.
4.5. Use description
Table 5
Preservation of fluids used in paper, textile and leather production - Curative treatment
Product type PT06: Preservatives for products during storage
Where relevant, an exact description of -
the authorised use
Target organism(s) (including Scientific name: no data
development stage) Common name: Bacteria
Development stage: no data
182/227 ELI: http://data.europa.eu/eli/reg_impl/2025/2202/ojEN
OJ L, 20.11.2025
Field(s) of use indoor use
Preservation of fluids used in paper, textile and leather production -
The biocidal product is used to reduce contamination by bacteria in
textile additives (woven and non-woven, natural and synthetic
including silicone emulsions) processing chemicals, all chemicals used
in the leather process industry and paper additives (e.g. water
pigment pastes, starch, natural gums, synthetic and natural latexes,
sizing agents, coating binders, retention aids, dyes, fluorescent
whitening agents, wet-strength resins) used in paper mills. The
biocidal product inhibits the growth microorganisms, which would
otherwise lead to odours formation, viscosity alteration,
discolouration of product and premature product failure.
Application method(s) Method: closed system
Detailed description:
Manual and automated dosing. The biocidal product should be
dispensed to the end use fluid at a point to ensure adequate mixing
using preferably automated metering pump or by manual addition.
Application rate(s) and frequency Application Rate:
Industrial uses: 1,5 - 14,5 % C(M)IT/MIT in the biocidal products;
Professional uses: 16 to 30 mg/kg of C(M)IT/MIT (3:1) in final
product
-
Number and timing of application:
The biocidal product is added at single dose at time of manufacturing,
storage or shipment.
Industrial uses: 1,5 - 14,5 % C(M)IT/MIT in the biocidal products.
Professional uses:
Curative treatment:
16 to 30 mg/kg of C(M)IT/MIT (3:1) in final product
Contact time: 24 hours
For the biocidal product as supplied: for industrial use only.
Category(ies) of users industrial
Pack sizes and packaging material For industrial and professional users:
— HDPE flask: 5 L (nominal)
— HDPE Pail / Jerrycan: 10 L, 20 L, 25 L, 30 L (nominal)
— Box with HDPE liner: 20 L
— HDPE Drum: 110 L, 120 L, 200 L, 260 L
— HDPE IBC: 650 L, 800 L, 1 000 L, 1 250 L
All products should be transport and stored in a vented room.
4.5.1. Use-specific instructions for use
— The preservative can be added at any stage of the production of the product.
— Earliest possible addition is recommended for optimal protection.
— Consult the manufacturer to determine the optimal dosage for the various products to be preserved.
ELI: http://data.europa.eu/eli/reg_impl/2025/2202/oj 183/227EN
OJ L, 20.11.2025
— It is recommended that the optimum biocide concentration and compatibility with individual formulations
is determined by means of laboratory tests.
— The duration and storage conditions of the preserved matrices may impact the efficacy of the product,
microbiological tests should be conducted to determine the appropriate application rate without exceeding
the maximum authorised application rate.
— The biocidal product shall be used for treatment of products (articles/mixtures) distributed only to
professional users.
4.5.2. Use-specific risk mitigation measures
— During handling phases of products from Meta SPC 1, 2, 3 and 4 (mixing and loading), exposure to the
product (corrosive and skin sensitizer products) has to be limited by use of PPE and application of technical
and organisational RMM:
— Minimisation of manual phases (process automation);
— Use of a dosing device;
— Regular cleaning of equipment and work area;
— Avoidance of contact with contaminated tools and objects;
— Good standard of general ventilation;
— Training and management of staff on good practice.
— PPE is as follows:
— protective chemical resistant gloves (glove material to be specified by the authorisation holder within
the product information);
— protective coverall (at least type 3 or 4, EN 14605) which is impermeable for the biocidal product
shall be worn (coverall material to be specified by the authorisation holder within the product
information);
— Eye protection;
— Substance/task appropriate respirator if ventilation is inadequate.
— The maximal products concentration used for the preservation of fluids used in paper, textile and leather
production being above the threshold value of 15 ppm, exposure has to be limited by use of PPE protecting
skin and mucous membranes potentially exposed and application of technical and organisational RMM:
— Minimisation of manual phases;
— Use of a dosing device;
— Regular cleaning of equipment and work area;
— Avoidance of contact with contaminated tools and objects;
— Good standard of general ventilation;
— Training and management of staff on good practice.
4.5.3. Where specific to the use, the particulars of likely direct or indirect effects, first aid instructions and emergency measures to
protect the environment
See general directions for use.
4.5.4. Where specific to the use, the instructions for safe disposal of the product and its packaging
See general directions for use.
184/227 ELI: http://data.europa.eu/eli/reg_impl/2025/2202/ojEN
OJ L, 20.11.2025
4.5.5. Where specific to the use, the conditions of storage and shelf-life of the product under normal conditions of storage
See general directions for use.
4.6. Use description
Table 6
Preservation of glues and adhesives
Product type PT06: Preservatives for products during storage
Where relevant, an exact description of -
the authorised use
Target organism(s) (including Scientific name: no data
development stage) Common name: Bacteria
Development stage: no data
Scientific name: no data
Common name: Yeasts
Development stage: no data
Field(s) of use indoor use
Preservation of glues and adhesives
The biocidal product is recommended to control the growth of
bacteria and yeasts in water-soluble and water-dispersed synthetic and
natural adhesives and tackifiers in storage containers before use
Application method(s) Method: closed system
Detailed description:
Manual and automated application. The biocidal product should be
dispensed to the end use fluid at a point to ensure adequate mixing
using preferably automated metering pump or by manual addition.
Application rate(s) and frequency Application Rate:
Industrial uses: 1,5 - 14,5 % C(M)IT/MIT in the biocidal products;
Professional uses: 8-30 mg/kg C(M)IT/MIT (3:1) in final product.
General public uses: 8-14,9 mg/kg C(M)IT/MIT (3:1) in final product.
-
Number and timing of application:
The biocidal product is added at single dose at the time of
manufacture, storage or shipment.
To ensure uniform distribution, slowly disperse using automated
metering or manual addition, into product with agitation. Mix
thoroughly until evenly dispersed throughout the product.
Industrial uses: 1,5 - 14,5 % C(M)IT/MIT in the biocidal products.
Professional uses:
8-30 mg/kg C(M)IT/MIT (3:1) in final product.
General public uses:
8-14,9 mg/kg C(M)IT/MIT (3:1) in final product.
For the biocidal product as supplied: for industrial use only.
Category(ies) of users industrial
ELI: http://data.europa.eu/eli/reg_impl/2025/2202/oj 185/227EN
OJ L, 20.11.2025
Pack sizes and packaging material For industrial and professional users:
— HDPE flask: 5 L (nominal)
— HDPE Pail / Jerrycan: 10 L, 20 L, 25 L, 30 L (nominal)
— Box with HDPE liner: 20 L
— HDPE Drum: 110 L, 120 L, 200 L, 260 L
— HDPE IBC: 650 L, 800 L, 1 000 L, 1 250 L
All products should be transport and stored in a vented room.
4.6.1. Use-specific instructions for use
— The preservative can be added at any stage of the production of the product.
— Earliest possible addition is recommended for optimal protection.
— Consult the manufacturer to determine the optimal dosage for the various products to be preserved.
— It is recommended that the optimum biocide concentration and compatibility with individual formulations
is determined by means of laboratory tests.
— The duration and storage conditions of the preserved matrices may impact the efficacy of the product,
microbiological tests should be conducted to determine the appropriate application rate without exceeding
the maximum authorised application rate.
— The biocidal product shall be used for treatment of products (articles/mixtures) distributed to professional
users and to the general public. For products distributed to the general public the maximal concentration
used must be below the threshold value of 15 ppm.
4.6.2. Use-specific risk mitigation measures
— During handling phases of products from Meta SPC 1, 2, 3 and 4 (mixing and loading), exposure to the
product (corrosive and skin sensitizer products) has to be limited by use of PPE and application of technical
and organisational RMM:
— Minimisation of manual phases (process automation);
— Use of a dosing device;
— Regular cleaning of equipment and work area;
— Avoidance of contact with contaminated tools and objects;
— Good standard of general ventilation;
— Training and management of staff on good practice.
— PPE is as follows:
— protective chemical resistant gloves (glove material to be specified by the authorisation holder within
the product information);
— protective coverall (at least type 3 or 4, EN 14605) which is impermeable for the biocidal product
shall be worn (coverall material to be specified by the authorisation holder within the product
information);
— Eye protection;
— Substance/task appropriate respirator if ventilation is inadequate.
186/227 ELI: http://data.europa.eu/eli/reg_impl/2025/2202/ojEN
OJ L, 20.11.2025
— For professional users, the maximal products concentration used for the preservation of glues and adhesives
being above the threshold value of 15 ppm, exposure has to be limited by use of PPE, protecting skin and
mucous membranes potentially exposed, and application of technical and organisational RMM:
— Minimisation of manual phases;
— Use of a dosing device;
— Regular cleaning of equipment and work area;
— Good standard of general ventilation;
— Training and management of staff on good practice.
4.6.3. Where specific to the use, the particulars of likely direct or indirect effects, first aid instructions and emergency measures to
protect the environment
See general directions for use.
4.6.4. Where specific to the use, the instructions for safe disposal of the product and its packaging
See general directions for use.
4.6.5. Where specific to the use, the conditions of storage and shelf-life of the product under normal conditions of storage
See general directions for use.
4.7. Use description
Table 7
Preservation of polymer lattices
Product type PT06: Preservatives for products during storage
Where relevant, an exact description of -
the authorised use
Target organism(s) (including Scientific name: no data
development stage) Common name: Bacteria
Development stage: no data
Scientific name: no data
Common name: Yeasts
Development stage: no data
Scientific name: no data
Common name: fungi
Development stage: no data
Field(s) of use indoor use
Preservation of polymer latexes
The biocidal product is recommended for the control of bacteria,
yeast and fungi in the manufacture, storage, and transport of latexes,
synthetic polymers including Hydrolysed Poly Acryl Amide (HPAM)
and biopolymers (e.g. xanthan, dextran..) natural latexes.
Application method(s) Method: closed system
Detailed description:
Manual and automated application. The biocidal product should be
dispensed to the end use fluid at a point to ensure adequate mixing
using preferably automated metering pump or by manual addition.
ELI: http://data.europa.eu/eli/reg_impl/2025/2202/oj 187/227EN
OJ L, 20.11.2025
Application rate(s) and frequency Application Rate:
Industrial uses: 1,5 - 14,5 % C(M)IT/MIT in the biocidal products;
Professional uses: 14,9 - 50 mg /kg of C(M)IT/MIT (3:1) in final
product.
-
Number and timing of application:
The biocidal product is added at single dose at the time of
manufacture, storage or shipment.
To ensure uniform distribution, slowly disperse using automated
metering or manual addition, into product with agitation. Mix
thoroughly until evenly dispersed throughout the product.
Industrial uses: 1,5 - 14,5 % C(M)IT/MIT in the biocidal products.
Professional uses
14,9 - 50 mg /kg of C(M)IT/MIT (3:1) in final product.
For the biocidal product as supplied: for industrial use only.
Category(ies) of users industrial
Pack sizes and packaging material For industrial and professional users:
— HDPE flask: 5 L (nominal)
— HDPE Pail / Jerrycan: 10 L, 20 L, 25 L, 30 L (nominal)
— Box with HDPE liner: 20 L
— HDPE Drum: 110 L, 120 L, 200 L, 260 L
— HDPE IBC: 650 L, 800 L, 1 000 L, 1 250 L
All products should be transport and stored in a vented room.
4.7.1. Use-specific instructions for use
— The preservative can be added at any stage of the production of the product.
— Earliest possible addition is recommended for optimal protection.
— Consult the manufacturer to determine the optimal dosage for the various products to be preserved.
— It is recommended that the optimum biocide concentration and compatibility with individual formulations
is determined by means of laboratory tests.
— The duration and storage conditions of the preserved matrices may impact the efficacy of the product,
microbiological tests should be conducted to determine the appropriate application rate without exceeding
the maximum authorised application rate.
— The biocidal product shall be used for treatment of products (articles/mixtures) distributed only to
professional users.
4.7.2. Use-specific risk mitigation measures
— During handling phases of products from Meta SPC 1, 2, 3 and 4 (mixing and loading), exposure to the
product (corrosive and skin sensitizer products) has to be limited by use of PPE and application of technical
and organisational RMM:
— Minimisation of manual phases (process automation);
— Use of a dosing device;
188/227 ELI: http://data.europa.eu/eli/reg_impl/2025/2202/ojEN
OJ L, 20.11.2025
— Regular cleaning of equipment and work area;
— Avoidance of contact with contaminated tools and objects;
— Good standard of general ventilation;
— Training and management of staff on good practice.
— PPE is as follows:
— protective chemical resistant gloves (glove material to be specified by the authorisation holder within
the product information);
— protective coverall (at least type 3 or 4, EN 14605) which is impermeable for the biocidal product
shall be worn (coverall material to be specified by the authorisation holder within the product
information);
— Eye protection;
— Substance/task appropriate respirator if ventilation is inadequate.
— The maximal products concentration used for the preservation of polymer lattices being above the threshold
value of 15 ppm, exposure has to be limited by use of PPE, protecting skin and mucous membranes
potentially exposed, and application of technical and organisational RMM:
— Minimisation of manual phases;
— Use of a dosing device;
— Regular cleaning of equipment and work area;
— Good standard of general ventilation;
— Training and management of staff on good practice.
4.7.3. Where specific to the use, the particulars of likely direct or indirect effects, first aid instructions and emergency measures to
protect the environment
See general directions for use.
4.7.4. Where specific to the use, the instructions for safe disposal of the product and its packaging
See general directions for use.
4.7.5. Where specific to the use, the conditions of storage and shelf-life of the product under normal conditions of storage
See general directions for use.
4.8. Use description
Table 8
Preservation of mineral slurries
Product type PT06: Preservatives for products during storage
Where relevant, an exact description of -
the authorised use
Target organism(s) (including Scientific name: no data
development stage) Common name: Bacteria
Development stage: no data
ELI: http://data.europa.eu/eli/reg_impl/2025/2202/oj 189/227EN
OJ L, 20.11.2025
Field(s) of use indoor use
Preservation of mineral slurries
The biocidal product is recommended to control the growth of
bacteria in aqueous-based inorganic/mineral slurries and inorganic
pigments which are formulated into paints, coatings and paper.
Application method(s) Method: closed system
Detailed description:
Manual and automated application. The biocidal product should be
dispensed as a tankside additive into the circulating use-dilution of
the fluid, using a metering pump or by manual pouring, at a point to
assure adequate mixing throughout the system.
Application rate(s) and frequency Application Rate:
Industrial uses: 1,5 - 14,5 % C(M)IT/MIT in the biocidal products;
Professional uses: 10- 30 mg/kg of C(M)IT/MIT (3:1) in final product.
-
Number and timing of application:
The biocidal product is added at single dose at the time of
manufacture, storage or shipment.
Industrial uses: 1,5 - 14,5 % C(M)IT/MIT in the biocidal products.
Professional uses:
10- 30 mg/kg of C(M)IT/MIT (3:1) in final product.
For the biocidal product as supplied: for industrial use only.
Category(ies) of users industrial
Pack sizes and packaging material For industrial and professional users:
— HDPE flask: 5 L (nominal)
— HDPE Pail / Jerrycan: 10 L, 20 L, 25 L, 30 L (nominal)
— Box with HDPE liner: 20 L
— HDPE Drum: 110 L, 120 L, 200 L, 260 L
— HDPE IBC: 650 L, 800 L, 1 000 L, 1 250 L
All products should be transport and stored in a vented room.
4.8.1. Use-specific instructions for use
— The preservative can be added at any stage of the production of the product.
— Earliest possible addition is recommended for optimal protection.
— Consult the manufacturer to determine the optimal dosage for the various products to be preserved.
— It is recommended that the optimum biocide concentration and compatibility with individual formulations
is determined by means of laboratory tests.
— The duration and storage conditions of the preserved matrices may impact the efficacy of the product,
microbiological tests should be conducted to determine the appropriate application rate without exceeding
the maximum authorised application rate.
— The biocidal product shall be used for treatment of products (articles/mixtures) distributed only to
professional users.
190/227 ELI: http://data.europa.eu/eli/reg_impl/2025/2202/ojEN
OJ L, 20.11.2025
4.8.2. Use-specific risk mitigation measures
— During handling phases of products from Meta SPC 1, 2, 3 and 4 (mixing and loading), exposure to the
product (corrosive and skin sensitizer products) has to be limited by use of PPE and application of technical
and organisational RMM:
— Minimisation of manual phases (process automation);
— Use of a dosing device;
— Regular cleaning of equipment and work area;
— Avoidance of contact with contaminated tools and objects;
— Good standard of general ventilation;
— Training and management of staff on good practice.
— PPE is as follows:
— protective chemical resistant gloves (glove material to be specified by the authorisation holder within
the product information);
— protective coverall (at least type 3 or 4, EN 14605) which is impermeable for the biocidal product
shall be worn (coverall material to be specified by the authorisation holder within the product
information);
— Eye protection;
— Substance/task appropriate respirator if ventilation is inadequate.
The maximal products concentration used for the preservation of mineral slurries being above the threshold value
of 15 ppm, exposure has to be limited by use of PPE, protecting skin and mucous membranes potentially exposed,
and application of technical and organisational RMM:
— Minimisation of manual phases;
— Use of a dosing device;
— Regular cleaning of equipment and work area;
— Good standard of general ventilation;
— Training and management of staff on good practice.
4.8.3. Where specific to the use, the particulars of likely direct or indirect effects, first aid instructions and emergency measures to
protect the environment
See general directions for use.
4.8.4. Where specific to the use, the instructions for safe disposal of the product and its packaging
See general directions for use.
4.8.5. Where specific to the use, the conditions of storage and shelf-life of the product under normal conditions of storage
See general directions for use.
ELI: http://data.europa.eu/eli/reg_impl/2025/2202/oj 191/227EN
OJ L, 20.11.2025
4.9. Use description
Table 9
Preservation of building products applied indoor only
Product type PT06: Preservatives for products during storage
Where relevant, an exact description of -
the authorised use
Target organism(s) (including Scientific name: no data
development stage) Common name: Bacteria
Development stage: no data
Scientific name: no data
Common name: Yeasts
Development stage: no data
Field(s) of use indoor use
Preservation of building (construction) products (including sealants,
caulks, plasters etc.)
The biocidal product is recommended to control the growth of
bacteria in building (construction) products (sealants, caulks,
biopolymers, plasters, fillers, admixtures concrete additives, joints
compounds,..).
Application method(s) Method: -
Detailed description:
Manual and automated dosing. The biocidal product should be
dispensed to the end use fluid at a point to ensure adequate mixing
using preferably automated metering pump or by manual addition.
Application rate(s) and frequency Application Rate:
Industrial uses: 1,5 - 14,5 % C(M)IT/MIT in the biocidal products;
Professional uses: Add at typical use rate between 16,2-30 mg C(M)
IT/MIT (3:1) per Kg final product to be treated.
-
Number and timing of application:
The biocidal product is added at single dose at the time of
manufacture, storage or shipment.
Slowly dispense using automated metering or manually. Mix
thoroughly until the biocidal product is evenly dispersed.
Industrial uses:
1,5 - 14,5 % C(M)IT/MIT in the biocidal products.
Professional uses:
Add at typical use rate between 16,2-30 mg C(M)IT/MIT (3:1) per Kg
final product to be treated.
For the biocidal product as supplied: for industrial use only.
Category(ies) of users industrial
Pack sizes and packaging material For industrial and professional users:
— HDPE flask: 5 L (nominal)
— HDPE Pail / Jerrycan: 10 L, 20 L, 25 L, 30 L (nominal)
— Box with HDPE liner: 20 L
— HDPE Drum: 110 L, 120 L, 200 L, 260 L
— HDPE IBC: 650 L, 800 L, 1 000 L, 1 250 L
All products should be transport and stored in a vented room.
192/227 ELI: http://data.europa.eu/eli/reg_impl/2025/2202/ojEN
OJ L, 20.11.2025
4.9.1. Use-specific instructions for use
— The preservative can be added at any stage of the production of the product.
— Earliest possible addition is recommended for optimal protection.
— Consult the manufacturer to determine the optimal dosage for the various products to be preserved.
— It is recommended that the optimum biocide concentration and compatibility with individual formulations
is determined by means of laboratory tests.
— The duration and storage conditions of the preserved matrices may impact the efficacy of the product,
microbiological tests should be conducted to determine the appropriate application rate without exceeding
the maximum authorised application rate.
— The biocidal product shall be used for treatment of products (articles/mixtures) distributed only to
professional users.
4.9.2. Use-specific risk mitigation measures
— This use is restricted to the preservation of building material applied indoor only.
— During handling phases for products from Meta SPC 1, 3 and 4 (mixing and loading), exposure to the
product (corrosive and skin sensitizer products) has to be limited by use of PPE and application of technical
and organisational RMM:
— Minimisation of manual phases (process automation);
— Use of a dosing device;
— Regular cleaning of equipment and work area;
— Avoidance of contact with contaminated tools and objects;
— Good standard of general ventilation;
— Training and management of staff on good practice.
— PPE is as follows:
— protective chemical resistant gloves (glove material to be specified by the authorisation holder within
the product information);
— protective coverall (at least type 3 or 4, EN 14605) which is impermeable for the biocidal product
shall be worn (coverall material to be specified by the authorisation holder within the product
information);
— Eye protection;
— Substance/task appropriate respirator if ventilation is inadequate.
For professional users, the maximal products concentration used for the preservation of building products being
above the threshold value of 15 ppm, exposure has to be limited by use of PPE, protecting skin and mucous
membranes potentially exposed, and application of technical and organisational RMM:
— Minimisation of manual phases;
— Regular cleaning of equipment and work area;
— Good standard of general ventilation;
— Training and management of staff on good practice.
ELI: http://data.europa.eu/eli/reg_impl/2025/2202/oj 193/227EN
OJ L, 20.11.2025
4.9.3. Where specific to the use, the particulars of likely direct or indirect effects, first aid instructions and emergency measures to
protect the environment
See general directions for use.
4.9.4. Where specific to the use, the instructions for safe disposal of the product and its packaging
See general directions for use.
4.9.5. Where specific to the use, the conditions of storage and shelf-life of the product under normal conditions of storage
See general directions for use.
4.10. Use description
Table 10
Preservation of inks
Product type PT06: Preservatives for products during storage
Where relevant, an exact description of -
the authorised use
Target organism(s) (including Scientific name: no data
development stage) Common name: Bacteria
Development stage: no data
Scientific name: no data
Common name: Yeasts
Development stage: no data
Field(s) of use indoor use
Preservation of inks
The biocidal product is recommended to control the growth of
bacteria and yeasts in inks and ink components (printing inks
lithographic, photographic, ink-jet fluids, water based dampening or
fountain solutions inks used for textile printing). The biocidal product
inhibits the growth of microorganisms, which would otherwise lead
to odour formation, viscosity alteration, product discolouration and
premature product failure.
Application method(s) Method: closed system
Detailed description:
Manual and automated dosing. The biocidal product should be
dispensed to the end use fluid at a point to ensure adequate mixing
using preferably automated metering pump or by manual addition.
Application rate(s) and frequency Application Rate:
Industrial uses: 1,5 - 14,5 % C(M)IT/MIT in the biocidal products.
Professional uses: 6-30 mg C(M)IT/MIT (3:1) /kg final product.
General public uses: 6-14,9 mg C(M)IT/MIT (3:1) /kg final product.
-
Number and timing of application:
The biocidal product is added at single dose at time of manufacturing,
storage or shipment.
194/227 ELI: http://data.europa.eu/eli/reg_impl/2025/2202/ojEN
OJ L, 20.11.2025
Industrial uses: 1,5 - 14,5 % C(M)IT/MIT in the biocidal products.
Professional uses:
6-30 mg C(M)IT/MIT (3:1) /kg final product.
General public uses:
6-14,9 mg C(M)IT/MIT (3:1) /kg final product.
For the biocidal product as supplied: for industrial use only.
Category(ies) of users industrial
Pack sizes and packaging material For industrial and professional users:
— HDPE flask: 5 L (nominal)
— HDPE Pail / Jerrycan: 10 L, 20 L, 25 L, 30 L (nominal)
— Box with HDPE liner: 20 L
— HDPE Drum: 110 L, 120 L, 200 L, 260 L
— HDPE IBC: 650 L, 800 L, 1 000 L, 1 250 L
All products should be transport and stored in a vented room.
4.10.1. Use-specific instructions for use
— The preservative can be added at any stage of the production of the product.
— Earliest possible addition is recommended for optimal protection.
— Consult the manufacturer to determine the optimal dosage for the various products to be preserved.
— It is recommended that the optimum biocide concentration and compatibility with individual formulations
is determined by means of laboratory tests.
— The duration and storage conditions of the preserved matrices may impact the efficacy of the product,
microbiological tests should be conducted to determine the appropriate application rate without exceeding
the maximum authorised application rate.
— The biocidal product shall be used for treatment of products (articles/mixtures) distributed to professional
users and to the general public. For products distributed to the general public the maximal concentration
used must be below the threshold value of 15 ppm.
4.10.2. Use-specific risk mitigation measures
— During handling phases of products from Meta SPC 1, 2, 3 and 4 (mixing and loading), exposure to the
product (corrosive and skin sensitizer products) has to be limited by use of PPE and application of technical
and organisational RMM:
— Minimisation of manual phases (process automation);
— Use of a dosing device;
— Regular cleaning of equipment and work area;
— Avoidance of contact with contaminated tools and objects;
— Good standard of general ventilation;
— Training and management of staff on good practice.
ELI: http://data.europa.eu/eli/reg_impl/2025/2202/oj 195/227EN
OJ L, 20.11.2025
— PPE is as follows:
— protective chemical resistant gloves (glove material to be specified by the authorisation holder within
the product information);
— protective coverall (at least type 3 or 4, EN 14605) which is impermeable for the biocidal product
shall be worn (coverall material to be specified by the authorisation holder within the product
information);
— Eye protection;
— Substance/task appropriate respirator if ventilation is inadequate.
— For professional users, the maximal products concentration used for the preservation of inks being above
the threshold value of 15 ppm, exposure has to be limited by use of PPE, protecting skin and mucous
membranes potentially exposed, and application of technical and organisational RMM:
— Minimisation of manual phases;
— Use of a dosing device;
— Regular cleaning of equipment and work area;
— Good standard of general ventilation;
— Training and management of staff on good practice.
4.10.3. Where specific to the use, the particulars of likely direct or indirect effects, first aid instructions and emergency measures to
protect the environment
See general directions for use.
4.10.4. Where specific to the use, the instructions for safe disposal of the product and its packaging
See general directions for use.
4.10.5. Where specific to the use, the conditions of storage and shelf-life of the product under normal conditions of storage
See general directions for use.
4.11. Use description
Table 11
Preservation of functional fluids (hydraulic fluids, antifreeze, corrosion inhibitors, etc. - excluding fuel
additives)
Product type PT06: Preservatives for products during storage
Where relevant, an exact description of -
the authorised use
Target organism(s) (including Scientific name: no data
development stage) Common name: Bacteria
Development stage: no data
Field(s) of use indoor use
Preservation of functional fluids (hydraulic fluids, antifreeze,
corrosion inhibitors, etc. - excluding fuel additives)
196/227 ELI: http://data.europa.eu/eli/reg_impl/2025/2202/ojEN
OJ L, 20.11.2025
The biocidal product is recommended to control the growth of
bacteria in functional fluids such as brake and hydraulic fluids,
antifreeze additives, corrosion inhibitors, spinning fluids. The
biocidal product inhibits the growth microorganisms, which would
otherwise lead to odours formation, viscosity alteration,
discolouration of product and premature product failure.
Application method(s) Method: closed system
Detailed description:
Manual and automated dosing. The biocidal product should be
dispensed to the end use fluid at a point to ensure adequate mixing
using preferably automated metering pump or by manual addition.
Application rate(s) and frequency Application Rate:
Industrial uses: 1,5 - 14,5 % C(M)IT/MIT in the biocidal products.
Professional uses: Add at a typical use rate between 6 to 30 mg C(M)
IT/MIT (3:1) per kg final product to be treated.
-
Number and timing of application:
The biocidal product is added at single dose at time of manufacturing,
storage or shipment.
Industrial uses: 1,5 - 14,5 % C(M)IT/MIT in the biocidal products.
Professional uses:
Add at a typical use rate between 6 to 30 mg C(M)IT/MIT (3:1) per kg
final product to be treated
For the biocidal product as supplied: for industrial use only.
Category(ies) of users industrial
Pack sizes and packaging material For industrial and professional users:
— HDPE flask: 5 L (nominal)
— HDPE Pail / Jerrycan: 10 L, 20 L, 25 L, 30 L (nominal)
— Box with HDPE liner: 20 L
— HDPE Drum: 110 L, 120 L, 200 L, 260 L
— HDPE IBC: 650 L, 800 L, 1 000 L, 1 250 L
All products should be transport and stored in a vented room.
4.11.1. Use-specific instructions for use
— The preservative can be added at any stage of the production of the product.
— Earliest possible addition is recommended for optimal protection.
— Consult the manufacturer to determine the optimal dosage for the various products to be preserved.
— It is recommended that the optimum biocide concentration and compatibility with individual formulations
is determined by means of laboratory tests.
— The duration and storage conditions of the preserved matrices may impact the efficacy of the product,
microbiological tests should be conducted to determine the appropriate application rate without exceeding
the maximum authorised application rate.
ELI: http://data.europa.eu/eli/reg_impl/2025/2202/oj 197/227EN
OJ L, 20.11.2025
— The biocidal product shall be used for treatment of products (articles/mixtures) distributed only to
professional users.
4.11.2. Use-specific risk mitigation measures
— During handling phases of products from Meta SPC 1, 2, 3 and 4 (mixing and loading), exposure to the
product (corrosive and skin sensitizer products) has to be limited by use of PPE and application of technical
and organisational RMM:
— Minimisation of manual phases (process automation);
— Use of a dosing device;
— Regular cleaning of equipment and work area;
— Avoidance of contact with contaminated tools and objects;
— Good standard of general ventilation;
— Training and management of staff on good practice.
— PPE is as follows:
— protective chemical resistant gloves (glove material to be specified by the authorisation holder within
the product information);
— protective coverall (at least type 3 or 4, EN 14605) which is impermeable for the biocidal product
shall be worn (coverall material to be specified by the authorisation holder within the product
information);
— Eye protection;
— Substance/task appropriate respirator if ventilation is inadequate.
— The maximal products concentration used for the preservation of functional fluids (hydraulic fluids,
antifreeze, corrosion inhibitors, etc…) being above the threshold value of 15 ppm, exposure has to be
limited by use of PPE, protecting skin and mucous membranes potentially exposed, and application of
technical and organisational RMM:
— Minimisation of manual phases;
— Use of a dosing device;
— Regular cleaning of equipment and work area;
— Good standard of general ventilation;
— Training and management of staff on good practice.
4.11.3. Where specific to the use, the particulars of likely direct or indirect effects, first aid instructions and emergency measures to
protect the environment
See general directions for use.
4.11.4. Where specific to the use, the instructions for safe disposal of the product and its packaging
See general directions for use.
4.11.5. Where specific to the use, the conditions of storage and shelf-life of the product under normal conditions of storage
See general directions for use.
198/227 ELI: http://data.europa.eu/eli/reg_impl/2025/2202/ojEN
OJ L, 20.11.2025
4.12. Use description
Table 12
Preservation of laboratory reagents
Product type PT06: Preservatives for products during storage
Where relevant, an exact description of -
the authorised use
Target organism(s) (including Scientific name: no data
development stage) Common name: Bacteria
Development stage: no data
Scientific name: no data
Common name: Yeasts
Development stage: no data
Field(s) of use indoor use
Preservation of laboratory reagents
.
The biocidal product is recommended to control the growth of
bacteria and yeasts in laboratory reagents.
Application method(s) Method: closed system
Detailed description:
Manual and automated dosing. The biocidal product should be
dispensed to the end use fluid at a point to ensure adequate mixing
using preferably automated metering pump or by manual addition.
Application rate(s) and frequency Application Rate:
Industrial uses: 1,5 - 14,5 % C(M)IT/MIT in the biocidal products.
Professional use: Add at typical use rate of 15,2 mg C(M)IT/MIT (3:1)
per kg final product to be treated.
-
Number and timing of application:
The biocidal product is added at single dose at the time of
manufacture, storage or shipment.
Slowly dispense using automated metering or manually. Mix
thoroughly until the biocidal product is evenly dispersed.
Industrial uses: 1,5 - 14,5 % C(M)IT/MIT in the biocidal products.
Professional use: Add at typical use rate of 15,2 mg C(M)IT/MIT (3:1)
per kg final product to be treated.
For the biocidal product as supplied: for industrial use only.
Category(ies) of users industrial
Pack sizes and packaging material For industrial and professional users:
— HDPE flask: 1 L
— HDPE flask: 5 L (nominal)
— HDPE Pail / Jerrycan: 10 L, 20 L, 25 L, 30 L (nominal)
— Box with HDPE liner: 20 L
— HDPE Drum: 110 L, 120 L, 200 L, 260 L
— HDPE IBC: 650 L, 800 L, 1 000 L, 1 250 L
All products should be transport and stored in a vented room.
ELI: http://data.europa.eu/eli/reg_impl/2025/2202/oj 199/227EN
OJ L, 20.11.2025
4.12.1. Use-specific instructions for use
— The preservative can be added at any stage of the production of the product.
— Earliest possible addition is recommended for optimal protection.
— Consult the manufacturer to determine the optimal dosage for the various products to be preserved.
— It is recommended that the optimum biocide concentration and compatibility with individual formulations
is determined by means of laboratory tests.
— The duration and storage conditions of the preserved matrices may impact the efficacy of the product,
microbiological tests should be conducted to determine the appropriate application rate without exceeding
the maximum authorised application rate.
— The biocidal product shall be used for treatment of products (articles/mixtures) distributed only to
professional users.
4.12.2. Use-specific risk mitigation measures
— During handling phases for products from Meta SPC 1, 3 and 4 (mixing and loading), exposure to the
product (corrosive and skin sensitizer products) has to be limited by use of PPE and application of technical
and organisational RMM:
— Minimisation of manual phases (process automation);
— Use of a dosing device;
— Regular cleaning of equipment and work area;
— Avoidance of contact with contaminated tools and objects;
— Good standard of general ventilation;
— Training and management of staff on good practice.
— PPE is as follows:
— protective chemical resistant gloves (glove material to be specified by the authorisation holder within
the product information);
— protective coverall (at least type 3 or 4, EN 14605) which is impermeable for the biocidal product
shall be worn (coverall material to be specified by the authorisation holder within the product
information);
— Eye protection;
— Substance/task appropriate respirator if ventilation is inadequate.
For professional users, the maximal products concentration used for the preservation of laboratory reagents being
above the threshold value of 15 ppm, exposure has to be limited by use of PPE, protecting skin and mucous
membranes potentially exposed, and application of technical and organisational RMM:
— Minimisation of manual phases;
— Use of a dosing device;
— Regular cleaning of equipment and work area;
— Good standard of general ventilation;
— Training and management of staff on good practice.
200/227 ELI: http://data.europa.eu/eli/reg_impl/2025/2202/ojEN
OJ L, 20.11.2025
4.12.3. Where specific to the use, the particulars of likely direct or indirect effects, first aid instructions and emergency measures to
protect the environment
See general directions for use.
4.12.4. Where specific to the use, the instructions for safe disposal of the product and its packaging
See general directions for use.
4.12.5. Where specific to the use, the conditions of storage and shelf-life of the product under normal conditions of storage
See general directions for use.
4.13. Use description
Table 13
Offline preservation of industrial reverse osmosis membranes
Product type PT06: Preservatives for products during storage
Where relevant, an exact description of -
the authorised use
Target organism(s) (including Scientific name: no data
development stage) Common name: Bacteria
Development stage: no data
Field(s) of use indoor use
Offline preservation of industrial reverse osmosis membranes
The biocidal product is recommended to control the growth of
bacteria of reverse osmosis and nanofiltration membranes producing
industrial water for extended periods of time.
Application method(s) Method: closed system
Detailed description:
Manual and automated dosing. The biocidal product should be
dispensed as a tankside additive into the circulating use-dilution of
the fluid, using a metering pump or by manual pouring, at a point to
ensure adequate mixing throughout the system. After complete filling
of the trains RO/NF systems with the biocide solution, pumps are
stopped (Off line treatment) for extended periods of time. Typically
C(M)IT/MIT (3:1) solutions are prepared in the CIP (cleaning in place)
tank and added via the dosing system. Dilution with permeate water
or high quality water is recommended for the preparation of the
biocide solution. Membranes should be soaked in the biocide solution
during the shut-down period.
Application rate(s) and frequency Application Rate:
7,5–20 g/m3 (ppm w/v) of C(M)IT/MIT (3:1).
-
Number and timing of application:
7,5–20 g/m3 (ppm w/v) of C(M)IT/MIT (3:1).
Category(ies) of users industrial
ELI: http://data.europa.eu/eli/reg_impl/2025/2202/oj 201/227EN
OJ L, 20.11.2025
Pack sizes and packaging material For industrial and professional users:
— HDPE flask: 5 L (nominal)
— HDPE Pail / Jerrycan: 10 L, 20 L, 25 L, 30 L (nominal)
— Box with HDPE liner: 20 L
— HDPE Drum: 110 L, 120 L, 200 L, 260 L
— HDPE IBC: 650 L, 800 L, 1 000 L, 1 250 L
All products should be transport and stored in a vented room.
4.13.1. Use-specific instructions for use
— The preservative can be added at any stage of the production of the product.
— Earliest possible addition is recommended for optimal protection.
— Consult the manufacturer to determine the optimal dosage for the various products to be preserved.
— It is recommended that the optimum biocide concentration and compatibility with individual formulations
is determined by means of laboratory tests.
— The duration and storage conditions of the preserved matrices may impact the efficacy of the product,
microbiological tests should be conducted to determine the appropriate application rate without exceeding
the maximum authorised application rate.
4.13.2. Use-specific risk mitigation measures
Rinse the system with water prior to perform the maintenance of the system.
— During handling phases for products from Meta SPC 1, 3 and 4 (mixing and loading), exposure to the
product (corrosive and skin sensitizer products) has to be limited by use of PPE and application of technical
and organisational RMM:
— Minimisation of manual phases (process automation);
— Use of a dosing device;
— Regular cleaning of equipment and work area;
— Avoidance of contact with contaminated tools and objects;
— Good standard of general ventilation;
— Training and management of staff on good practice.
— PPE is as follows:
— protective chemical resistant gloves (glove material to be specified by the authorisation holder within
the product information);
— protective coverall (at least type 3 or 4, EN 14605) which is impermeable for the biocidal product
shall be worn (coverall material to be specified by the authorisation holder within the product
information);
— Eye protection;
— Substance/task appropriate respirator if ventilation is inadequate.
4.13.3. Where specific to the use, the particulars of likely direct or indirect effects, first aid instructions and emergency measures to
protect the environment
See general directions for use.
202/227 ELI: http://data.europa.eu/eli/reg_impl/2025/2202/ojEN
OJ L, 20.11.2025
4.13.4. Where specific to the use, the instructions for safe disposal of the product and its packaging
See general directions for use.
4.13.5. Where specific to the use, the conditions of storage and shelf-life of the product under normal conditions of storage
See general directions for use.
4.14. Use description
Table 14
Preservation of liquids used in closed recirculating cooling systems
Product type PT11: Preservatives for liquid-cooling and processing systems
Where relevant, an exact description of -
the authorised use
Target organism(s) (including Scientific name: no data
development stage) Common name: Bacteria (including Legionella pneumophila)
Development stage: no data
Scientific name: no data
Common name: Yeasts
Development stage: no data
Scientific name: no data
Common name: fungi
Development stage: no data
Field(s) of use indoor use
outdoor use
Preservation of liquids used in closed recirculating cooling systems
(Closed re-circulating cooling water systems comprise compressor
cooling, air conditioning chilled water, boilers, engine jacket cooling,
power supply cooling, and other industrial processes).
The biocidal product is used to control the growth of aerobes and
anaerobes bacteria, yeast, fungi, and biofilm in the circulating water
of closed systems
Application method(s) Method: closed system
Detailed description:
Manual and automated dosing.
Application rate(s) and frequency Application Rate:
Curative efficacy:- against bacteria (including L. pneumophila) at 5 -
14,9 g C(M)IT/MIT (3:1) / m3 of water. Contact time: 24 hours -
against biofilm: 14,9 g C(M)IT/MIT (3:1) / m3 of water. Contact time:
24 hours.- against fungi and yeasts at 1 – 3 g C(M)IT/MIT (3:1) / m3
of water. Contact time: 48 hours. Preventive efficacy:- against bacteria
(including L. pneumophila) at 3 – 14,9 g C(M)IT/MIT (3:1) / m3 of
water. - against biofilm (including L. pneumophila): 3 g C(M)IT/MIT
(3:1) / m3 of water.
-
ELI: http://data.europa.eu/eli/reg_impl/2025/2202/oj 203/227EN
OJ L, 20.11.2025
Number and timing of application:
Curative efficacy:
— against bacteria (including L. pneumophila) at 5 - 14,9 g C(M)
IT/MIT (3:1) / m3 of water.
Contact time: 24 hours
— against biofilm: 14,9 g C(M)IT/MIT (3:1) / m3 of water.
Contact time: 24 hours
— against fungi and yeasts at 1 – 3 g C(M)IT/MIT (3:1) / m3 of water.
Contact time: 48 hours
Preventive efficacy:
against bacteria (including L. pneumophila) at 3 – 14,9 g C(M)IT/MIT
(3:1) / m3 of water.
against biofilm (including L. pneumophila): 3 g C(M)IT/MIT (3:1) /
m3 of water.
Category(ies) of users industrial
Pack sizes and packaging material For industrial and professional users:
— HDPE flask: 5 L (nominal)
— HDPE Pail / Jerrycan: 10 L, 20 L, 25 L, 30 L (nominal)
— Box with HDPE liner: 20 L
— HDPE Drum: 110 L, 120 L, 200 L, 260 L
— HDPE IBC: 650 L, 800 L, 1 000 L, 1 250 L
All products should be transport and stored in a vented room.
4.14.1. Use-specific instructions for use
Microbiological tests to prove adequacy of preservation have to be undertaken by the user of C(M)IT/MIT products
in order to determine the effective dose of the preservative for the specific matrix/location/system. If needed,
consult the manufacturer of the preservative product.
4.14.2. Use-specific risk mitigation measures
— Rinse the system (especially the dispensing pumps) with water prior to perform the cleaning step.
— During handling phases (mixing and loading) and cleaning of the dispensing pumps, exposure to the
product (corrosive and skin sensitizer product) has to be limited by use of PPE and application of technical
and organisational RMM:
— Minimisation of manual phases (process automation);
— Use of a dosing device;
— Regular cleaning of equipment and work area;
— Avoidance of contact with contaminated tools and objects;
— Good standard of general ventilation;
— Training and management of staff on good practice.
204/227 ELI: http://data.europa.eu/eli/reg_impl/2025/2202/ojEN
OJ L, 20.11.2025
— PPE is as follows:
— protective chemical resistant gloves (glove material to be specified by the authorisation holder within
the product information);
— protective coverall (at least type 3 or 4, EN 14605) which is impermeable for the biocidal product
shall be worn (coverall material to be specified by the authorisation holder within the product
information);
— Eye protection;
— Substance/task appropriate respirator if ventilation is inadequate.
4.14.3. Where specific to the use, the particulars of likely direct or indirect effects, first aid instructions and emergency measures to
protect the environment
See general directions for use.
4.14.4. Where specific to the use, the instructions for safe disposal of the product and its packaging
See general directions for use.
4.14.5. Where specific to the use, the conditions of storage and shelf-life of the product under normal conditions of storage
See general directions for use.
4.15. Use description
Table 15
Preservation of liquids used in small open recirculating cooling systems
Product type PT11: Preservatives for liquid-cooling and processing systems
Where relevant, an exact description of -
the authorised use
Target organism(s) (including Scientific name: no data
development stage) Common name: Bacteria (including Legionella pneumophila)
Development stage: no data
Scientific name: no data
Common name: Yeasts
Development stage: no data
Scientific name: no data
Common name: fungi
Development stage: no data
Scientific name: no data
Common name: Algae (green algae and cyanobacteria)
Development stage: no data
Field(s) of use indoor use
outdoor use
Preservation of liquids used in small open recirculating cooling
systems (blowdown and recirculating flow rates, as well as total
volume of water limited to 2 m3/h, and 100 m3/h and 300 m3
respectively)
Process and cooling water: Used to control the growth of bacteria,
algae, fungi and biofilm
ELI: http://data.europa.eu/eli/reg_impl/2025/2202/oj 205/227EN
OJ L, 20.11.2025
Application method(s) Method: open system
Detailed description:
Manual and automated dosing. .
Application rate(s) and frequency Application Rate:
Curative treatment Against bacteria (including L. pneumophila) at 5 –
14,9 g C(M)IT/MIT (3:1) / m3 of water , - against biofilm (including L.
pneumophila) at 1,5 to 14,9 g C(M)IT/MIT (3:1) / m3 of water, -
against fungi (including yeast) at 1 – 14,9 g C(M)IT/MIT (3:1) / m3 of
water. Preventive treatment: - Against bacteria, green algae and
cyanobacteria at 3 g C(M)IT/MIT (3:1) / m3 of water, - against biofilm
(including L. pneumophila) at 3 g C(M)IT/MIT (3:1) / m3 of water.
-
Number and timing of application:
Curative treatment:
— Against bacteria (including L. pneumophila) at 5 – 14,9 g C(M)
IT/MIT (3:1) / m3 of water
Contact time: 24 hours
— against biofilm (including L. pneumophila) at 1,5 - 14,9 g C(M)
IT/MIT (3:1) / m3 of water
Contact time: 48 hours.
— against fungi and yeast at 1 – 14,9 g C(M)IT/MIT (3:1) / m3 of
water
Contact time: 48 hours.
Preventive treatment:
— against bacteria, green algae and cyanobacteria at 3 g C(M)IT/MIT
(3:1) / m3 of water.
— against biofilm (including L. pneumophila) at 3 g C(M)IT/MIT (3:1)
/ m3 of water.
Category(ies) of users industrial
Pack sizes and packaging material For industrial and professional users:
— HDPE flask: 5 L (nominal)
— HDPE Pail / Jerrycan: 10 L, 20 L, 25 L, 30 L (nominal)
— Box with HDPE liner: 20 L
— HDPE Drum: 110 L, 120 L, 200 L, 260 L
— HDPE IBC: 650 L, 800 L, 1 000 L, 1 250 L
All products should be transport and stored in a vented room.
4.15.1. Use-specific instructions for use
Microbiological tests to prove adequacy of preservation have to be undertaken by the user of C(M)IT/MIT products
in order to determine the effective dose of the preservative for the specific matrix/location/system. If needed,
consult the manufacturer of the preservative product.
206/227 ELI: http://data.europa.eu/eli/reg_impl/2025/2202/ojEN
OJ L, 20.11.2025
4.15.2. Use-specific risk mitigation measures
— Rinse the system (especially the dispensing pumps) with water prior to perform the cleaning step.
— During handling phases (mixing and loading) and cleaning of the dispensing pumps, exposure to the
product (corrosive and skin sensitizer product) has to be limited by use of PPE and application of technical
and organisational RMM:
— Minimisation of manual phases (process automation);
— Use of a dosing device;
— Regular cleaning of equipment and work area;
— Avoidance of contact with contaminated tools and objects;
— Good standard of general ventilation;
— Training and management of staff on good practice.
— PPE is as follows:
— protective chemical resistant gloves (glove material to be specified by the authorisation holder within
the product information);
— protective coverall (at least type 3 or 4, EN 14605) which is impermeable for the biocidal product
shall be worn (coverall material to be specified by the authorisation holder within the product
information);
— Eye protection;
— Substance/task appropriate respirator if ventilation is inadequate.
— Cooling fluid must not enter surface water directly. Use product only in premises that are connected to
a STP.
— The product can only be used when the cooling towers are equipped with drift eliminators that reduce the
drift at least by 99%.
4.15.3. Where specific to the use, the particulars of likely direct or indirect effects, first aid instructions and emergency measures to
protect the environment
See general directions for use.
4.15.4. Where specific to the use, the instructions for safe disposal of the product and its packaging
See general directions for use.
4.15.5. Where specific to the use, the conditions of storage and shelf-life of the product under normal conditions of storage
See general directions for use.
4.16. Use description
Table 16
Preservation of liquids used in pasteurizers, conveyor belts and air washers
Product type PT11: Preservatives for liquid-cooling and processing systems
Where relevant, an exact description of -
the authorised use
ELI: http://data.europa.eu/eli/reg_impl/2025/2202/oj 207/227EN
OJ L, 20.11.2025
Target organism(s) (including Scientific name: no data
development stage) Common name: Bacteria (including Legionella pneumophila)
Development stage: no data
Scientific name: no data
Common name: Yeasts
Development stage: no data
Scientific name: no data
Common name: fungi
Development stage: no data
Scientific name: no data
Common name: Algae (green algae and cyanobacteria)
Development stage: no data
Field(s) of use indoor use
outdoor use
Preservation of liquids used in non-food pasteurizers and conveyor
belts, air washers.
Application method(s) Method: -
Detailed description:
The biocidal product is dosed automatically in the heat transfer fluid,
in a place of good mixing (e.g. collecting sump below the conveyor
belt). The feeding pipe is used to dose the biocidal product below the
water level in order to limit its evaporation.
Application rate(s) and frequency Application Rate:
Curative treatment: -against bacteria (including L. pneumophila): 5 -
14,9 g C(M)IT/MIT (3:1) / m3 of water - against biofilm (including L.
pneumophila) at 1,5 - 14,9 g C(M)IT/MIT (3:1) / m3 of water - against
fungi and yeast at 1 – 14,9 g C(M)IT/MIT (3:1) / m3 of water.
Preventive treatment: Against bacteria, green algae and cyanobacteria
at 3 g C(M)IT/MIT (3:1) / m3 of water, against biofilm (including L.
pneumophila) at 3 g C(M)IT/MIT (3:1) / m3 of water.
-
Number and timing of application:
Curative treatment:
against bacteria (including L. pneumophila): 5 - 14,9 g C(M)IT/MIT
(3:1) / m3 of water.
Contact time: 24 hours
— against biofilm (including L. pneumophila) at 1,5 - 14,9 g C(M)
IT/MIT (3:1) / m3 of water
Contact time: 48 hours.
— against fungi and yeast at 1 – 14,9 g C(M)IT/MIT (3:1) / m3 of
water
Contact time: 48 hours.
Preventive treatment:
— Against bacteria, green algae and cyanobacteria at 3 g C(M)IT/MIT
(3:1) / m3 of water.
— against biofilm (including L. pneumophila) at 3 g C(M)IT/MIT (3:1)
/ m3 of water.
Category(ies) of users industrial
208/227 ELI: http://data.europa.eu/eli/reg_impl/2025/2202/ojEN
OJ L, 20.11.2025
Pack sizes and packaging material For industrial and professional users:
— HDPE flask: 5 L (nominal)
— HDPE Pail / Jerrycan: 10 L, 20 L, 25 L, 30 L (nominal)
— Box with HDPE liner: 20 L
— HDPE Drum: 110 L, 120 L, 200 L, 260 L
— HDPE IBC: 650 L, 800 L, 1 000 L, 1 250 L
All products should be transport and stored in a vented room.
4.16.1. Use-specific instructions for use
Microbiological tests to prove adequacy of preservation have to be undertaken by the user of C(M)IT/MIT products
in order to determine the effective dose of the preservative for the specific matrix/location/system. If needed,
consult the manufacturer of the preservative product.
Air washers: For use only in industrial air-washer systems that maintain effective mist eliminating components.
4.16.2. Use-specific risk mitigation measures
— Rinse the system (especially the dispensing pumps) with water prior to perform the cleaning step.
— During handling phases (mixing and loading) and cleaning of the dispensing pumps, exposure to the
product (corrosive and skin sensitizer product) has to be limited by use of PPE and application of technical
and organisational RMM:
— Minimisation of manual phases (process automation);
— Use of a dosing device;
— Regular cleaning of equipment and work area;
— Avoidance of contact with contaminated tools and objects;
— Good standard of general ventilation;
— Training and management of staff on good practice.
— PPE is as follows:
— protective chemical resistant gloves (glove material to be specified by the authorisation holder within
the product information);
— protective coverall (at least type 3 or 4, EN 14605) which is impermeable for the biocidal product
shall be worn (coverall material to be specified by the authorisation holder within the product
information);
— Eye protection;
— Substance/task appropriate respirator if ventilation is inadequate.
4.16.3. Where specific to the use, the particulars of likely direct or indirect effects, first aid instructions and emergency measures to
protect the environment
See general directions for use.
4.16.4. Where specific to the use, the instructions for safe disposal of the product and its packaging
See general directions for use.
ELI: http://data.europa.eu/eli/reg_impl/2025/2202/oj 209/227EN
OJ L, 20.11.2025
4.16.5. Where specific to the use, the conditions of storage and shelf-life of the product under normal conditions of storage
See general directions for use.
4.17. Use description
Table 17
Preservation of wood treatment solutions
Product type PT11: Preservatives for liquid-cooling and processing systems
Where relevant, an exact description of -
the authorised use
Target organism(s) (including Scientific name: fungi
development stage) Common name: other
Development stage: no data
Field(s) of use indoor use
outdoor use
Preservation of wood treatment solutions for application on wood of
classes 1, 2 and 3 only. The biocidal product is used as a preservative
for aqueous wood preservative treatment solution during the wet-
state process used in timber treatment solutions.
Application method(s) Method: -
Detailed description:
-
Application rate(s) and frequency Application Rate:
Preventive treatment: against fungi: 15 - 50 g C(M)IT/MIT (3:1) / m3
of in use wood preservation solution
-
Number and timing of application:
Preventive treatment: against fungi: 15 - 50 g C(M)IT/MIT (3:1) / m3
of in use wood preservation solution
Category(ies) of users industrial
Pack sizes and packaging material For industrial and professional users:
— HDPE flask: 5 L (nominal)
— HDPE Pail / Jerrycan: 10 L, 20 L, 25 L, 30 L (nominal)
— Box with HDPE liner: 20 L
— HDPE Drum: 110 L, 120 L, 200 L, 260 L
— HDPE IBC: 650 L, 800 L, 1 000 L, 1 250 L
All products should be transport and stored in a vented room.
4.17.1. Use-specific instructions for use
Microbiological tests to prove adequacy of preservation have to be undertaken by the user of C(M)IT/MIT products
in order to determine the effective dose of the preservative for the specific matrix/location/system. If needed,
consult the manufacturer of the preservative product.
— The biocidal product is not intended to function as a wood preservative against wood destroying fungus
relative to product type 8.
210/227 ELI: http://data.europa.eu/eli/reg_impl/2025/2202/ojEN
OJ L, 20.11.2025
4.17.2. Use-specific risk mitigation measures
— During handling phases (mixing and loading) and cleaning phases, exposure to the product (corrosive and
skin sensitizer product) has to be limited by use of PPE and application of technical and organisational RMM:
— Minimisation of manual phases (process automation);
— Use of a dosing device;
— Regular cleaning of equipment and work area;
— Avoidance of contact with contaminated tools and objects;
— Good standard of general ventilation;
— Training and management of staff on good practice.
— PPE is as follows:
— protective chemical resistant gloves (glove material to be specified by the authorisation holder within
the product information);
— protective coverall (at least type 3 or 4, EN 14605) which is impermeable for the biocidal product
shall be worn (coverall material to be specified by the authorisation holder within the product
information);
— Eye protection;
— Substance/task appropriate respirator if ventilation is inadequate.
— The product shall not be used in a wood treatment solution to be applied to wood which may come in direct
contact with food, feeding stuff and livestock animals
— The product can be used to preserve wood treatment solutions for the treatment of wood in use classes 1, 2
and 3 only.
— The product can be used in a wood treatment solution where the industrial application processes of wood
treatment can be carried out within a contained area situated on impermeable hard standing with bunding
to prevent run-off and a recovery system in place (e.g. sump).
— The product can be used in wood treatment solutions for the preservation of freshly treated timber, which
after treatment is stored under shelter or on impermeable hard standing, or both, to prevent direct losses to
soil, sewer or water. Any losses of wood treatment solution shall be collected for reuse or disposal.
— The product can be used only in wood treatment solutions for industrial application if these cannot be
released to soil, ground- and surface water or any kind of sewer and the wood treatment solutions and/or
the product are collected and reused or disposed of as hazardous waste.
— The biocidal product can be used only in wood treatment solutions used for the treatment of objects or
materials which are stored until completely dried on impermeable ground and under roof, to avoid leakage
into the soil.
4.17.3. Where specific to the use, the particulars of likely direct or indirect effects, first aid instructions and emergency measures to
protect the environment
See general directions for use.
4.17.4. Where specific to the use, the instructions for safe disposal of the product and its packaging
See general directions for use.
ELI: http://data.europa.eu/eli/reg_impl/2025/2202/oj 211/227EN
OJ L, 20.11.2025
4.17.5. Where specific to the use, the conditions of storage and shelf-life of the product under normal conditions of storage
See general directions for use.
4.18. Use description
Table 18
Preservation of recirculating fluids used in textile and fiber processing, leather processing, photo-
processing and fountain solution systems
Product type PT11: Preservatives for liquid-cooling and processing systems
Where relevant, an exact description of -
the authorised use
Target organism(s) (including Scientific name: no data
development stage) Common name: Bacteria
Development stage: no data
Field(s) of use indoor use
Preservation of recirculating fluids used in textile, fiber processing,
leather processing, photo-processing and fountain solution systems
C(M)IT/MIT (3:1) biocidal products are used for the preservation of
textile and spinning fluids, photo processing solutions, leather
process (e.g. washing and soaking treatment stages) and printing
fountain solutions to control the integrity of recirculating fluid by
reducing microbial contamination in the bulk solution.
Application method(s) Method: -
Detailed description:
Manual and automated dosing.The preservation of all end-products is
performed in most cases highly automated by industrial usersThe
biocidal product is added to the central sump, basin or recirculating
lines in an area with adequate mixing.
Application rate(s) and frequency Application Rate:
Curative treatment: Against bacteria at 16-30 mg C(M)IT/MIT (3:1)
per L of fluid
-
Number and timing of application:
Curative treatment: Against bacteria at 16-30 mg C(M)IT/MIT (3:1)
per L of fluid
Contact time 5 days
Category(ies) of users industrial
Pack sizes and packaging material For industrial and professional users:
— HDPE flask: 5 L (nominal)
— HDPE Pail / Jerrycan: 10 L, 20 L, 25 L, 30 L (nominal)
— Box with HDPE liner: 20 L
— HDPE Drum: 110 L, 120 L, 200 L, 260 L
— HDPE IBC: 650 L, 800 L, 1 000 L, 1 250 L
All products should be transport and stored in a vented room.
212/227 ELI: http://data.europa.eu/eli/reg_impl/2025/2202/ojEN
OJ L, 20.11.2025
4.18.1. Use-specific instructions for use
Microbiological tests to prove adequacy of preservation have to be undertaken by the user of C(M)IT/MIT products
in order to determine the effective dose of the preservative for the specific matrix/location/system. If needed,
consult the manufacturer of the preservative product.
4.18.2. Use-specific risk mitigation measures
— Rinse the system (especially the dispensing pumps) with water prior to perform the cleaning step.
— During handling phases (mixing and loading) and cleaning of the dispensing pumps, exposure to the
product (corrosive and skin sensitizer product) has to be limited by use of PPE and application of technical
and organisational RMM:
— Minimisation of manual phases (process automation);
— Use of a dosing device;
— Regular cleaning of equipment and work area;
— Avoidance of contact with contaminated tools and objects;
— Good standard of general ventilation;
— Training and management of staff on good practice.
— PPE is as follows:
— protective chemical resistant gloves (glove material to be specified by the authorisation holder within
the product information);
— protective coverall (at least type 3 or 4, EN 14605) which is impermeable for the biocidal product
shall be worn (coverall material to be specified by the authorisation holder within the product
information);
— Eye protection;
— Substance/task appropriate respirator if ventilation is inadequate.
— Liquids used in textile and fiber processing fluids must not enter surface water directly. Use product only in
premises that are connected to a STP.
— Recirculating liquids in photoprocessing systems and fountain solution systems must not enter surface water
directly. Use product only in premises that are connected to a STP.
4.18.3. Where specific to the use, the particulars of likely direct or indirect effects, first aid instructions and emergency measures to
protect the environment
See general directions for use.
4.18.4. Where specific to the use, the instructions for safe disposal of the product and its packaging
See general directions for use.
4.18.5. Where specific to the use, the conditions of storage and shelf-life of the product under normal conditions of storage
See general directions for use.
ELI: http://data.europa.eu/eli/reg_impl/2025/2202/oj 213/227EN
OJ L, 20.11.2025
4.19. Use description
Table 19
Preservation of re-circulating liquids used in paint spray booths and electrodeposition coating systems
Product type PT11: Preservatives for liquid-cooling and processing systems
Where relevant, an exact description of -
the authorised use
Target organism(s) (including Scientific name: no data
development stage) Common name: Bacteria
Development stage: no data
Scientific name: no data
Common name: Yeasts
Development stage: no data
Field(s) of use indoor use
Preservation of re-circulating liquids used in paint spray booths and
electrodeposition coating systems.
The biocidal product is used for preservation of fluids in pre-
treatment processes (Cleaning treatment for grease removal and soil,
degreasing Phosphating process, Rinse off tanks) paint spray booths
and electrodeposition coating systems (e.g. cataphoretic baths)
applied in Car Refinishing and Original equipment Car
Manufacturing to control the integrity of recirculating fluid by
reducing microbial contamination from bacteria and fungi in the
bulk solution.
Application method(s) Method: -
Detailed description:
-
Application rate(s) and frequency Application Rate:
Preventive treatment: 7,5 to 30 mg C(M)IT/MIT (3:1) per Kg final
product.
-
Number and timing of application:
Preventive treatment: 7,5 to 30 mg C(M)IT/MIT (3:1) per Kg final
product.
The biocidal product is added at the time of manufacture, storage or
shipment.
Category(ies) of users industrial
Pack sizes and packaging material For industrial and professional users:
— HDPE flask: 5 L (nominal)
— HDPE Pail / Jerrycan: 10 L, 20 L, 25 L, 30 L (nominal)
— Box with HDPE liner: 20 L
— HDPE Drum: 110 L, 120 L, 200 L, 260 L
— HDPE IBC: 650 L, 800 L, 1 000 L, 1 250 L
All products should be transport and stored in a vented room.
214/227 ELI: http://data.europa.eu/eli/reg_impl/2025/2202/ojEN
OJ L, 20.11.2025
4.19.1. Use-specific instructions for use
Microbiological tests to prove adequacy of preservation have to be undertaken by the user of C(M)IT/MIT products
in order to determine the effective dose of the preservative for the specific matrix/location/system. If needed,
consult the manufacturer of the preservative product.
4.19.2. Use-specific risk mitigation measures
— Rinse the system (especially the dispensing pumps) with water prior to perform the cleaning step.
— During handling phases (mixing and loading) and cleaning of the dispensing pumps, exposure to the
product (corrosive and skin sensitizer product) has to be limited by use of PPE and application of technical
and organisational RMM:
— Minimisation of manual phases (process automation);
— Use of a dosing device;
— Regular cleaning of equipment and work area;
— Avoidance of contact with contaminated tools and objects;
— Good standard of general ventilation;
— Training and management of staff on good practice.
— PPE is as follows:
— protective chemical resistant gloves (glove material to be specified by the authorisation holder within
the product information);
— protective coverall (at least type 3 or 4, EN 14605) which is impermeable for the biocidal product
shall be worn (coverall material to be specified by the authorisation holder within the product
information);
— Eye protection;
— Substance/task appropriate respirator if ventilation is inadequate.
4.19.3. Where specific to the use, the particulars of likely direct or indirect effects, first aid instructions and emergency measures to
protect the environment
See general directions for use.
4.19.4. Where specific to the use, the instructions for safe disposal of the product and its packaging
See general directions for use.
4.19.5. Where specific to the use, the conditions of storage and shelf-life of the product under normal conditions of storage
See general directions for use.
4.20. Use description
Table 20
Preservation of liquids used in closed recirculating heating systems and associated pipework
Product type PT11: Preservatives for liquid-cooling and processing systems
Where relevant, an exact description of -
the authorised use
ELI: http://data.europa.eu/eli/reg_impl/2025/2202/oj 215/227EN
OJ L, 20.11.2025
Target organism(s) (including Scientific name: no data
development stage) Common name: Bacteria (anaerobes and aerobes (including
Legionella pneumophila)
Development stage: no data
Scientific name: no data
Common name: Yeasts
Development stage: no data
Scientific name: no data
Common name: fungi
Development stage: no data
Field(s) of use indoor use
outdoor use
Preservation of liquids used in closed recirculating heating systems
and associated pipework. Pre-commission biocide flushing of new or
existing pipework systems (heating and chilling pipework) includes
used or new structural pipework built on industrial building projects.
Closed recirculating heating systems: pre-commission biocidal
product flushing of new or existing pipework systems (heating and
chilling pipework) includes used or new structural pipework built on
industrial building projects. The biocidal product is used to control
the growth of aerobic and anaerobic bacteria, fungi and biofilm in the
circulating water of closed systems. Closed systems are less
susceptible to corrosion, scaling and biological fouling than open
systems. However microbial problems can occur, if the system is left
filled and untreated. This is due to the presence of nitrite and glycols
used as nutrients by microbes.
Application method(s) Method: closed system
Detailed description:
Manual and automated dosing. The biocidal product is dosed
automatically in the heat transfer fluid, in a place of good mixing.
The feeding pipe must dose the biocidal product below the water
level in order to limit the evaporation of the biocidal product.
Application rate(s) and frequency Application Rate:
Curative treatment - against bacteria at 5 g C(M)IT/MIT (3:1) / m3 of
water (including L. pneumophila) - against biofilm at 14,9 g C(M)
IT/MIT (3:1) / m3 of water - against fungi and yeast at 1 g C(M)IT/MIT
/ m3 of water Preventive treatment - against bacteria (including L.
pneumophila) at 3 g C(M)IT/MIT (3:1) / m3 of water - against biofilm
at 3 g C(M)IT/MIT (3:1) / m3 of water.
-
Number and timing of application:
Curative treatment:
— against bacteria at 5 g C(M)IT/MIT (3:1) / m3 of water (including L.
pneumophila)
Contact time: 24 hours
— against biofilm at 14,9 g C(M)IT/MIT (3:1) / m3 of water
Contact time: 24 hours
— against fungi and yeast at 1 g C(M)IT/MIT / m3 of water Contact
time: 48 hours
216/227 ELI: http://data.europa.eu/eli/reg_impl/2025/2202/ojEN
OJ L, 20.11.2025
Preventive treatment
— against bacteria (including L. pneumophila) at 3 g C(M)IT/MIT
(3:1) / m3 of water and against biofilm at 3 g C(M)IT/MIT (3:1) /
m3 of water.
Category(ies) of users industrial
Pack sizes and packaging material For industrial and professional users:
— HDPE flask: 5 L (nominal)
— HDPE Pail / Jerrycan: 10 L, 20 L, 25 L, 30 L (nominal)
— Box with HDPE liner: 20 L
— HDPE Drum: 110 L, 120 L, 200 L, 260 L
— HDPE IBC: 650 L, 800 L, 1 000 L, 1 250 L
All products should be transport and stored in a vented room.
4.20.1. Use-specific instructions for use
Microbiological tests to prove adequacy of preservation have to be undertaken by the user of C(M)IT/MIT products
in order to determine the effective dose of the preservative for the specific matrix/location/system. If needed,
consult the manufacturer of the preservative product.
4.20.2. Use-specific risk mitigation measures
— Rinse the system (especially the dispensing pumps) with water prior to perform the cleaning step.
— During handling phases (mixing and loading) and cleaning of the dispensing pumps, exposure to the
product (corrosive and skin sensitizer product) has to be limited by use of PPE and application of technical
and organisational RMM:
— Minimisation of manual phases (process automation);
— Use of a dosing device;
— Regular cleaning of equipment and work area;
— Avoidance of contact with contaminated tools and objects;
— Good standard of general ventilation;
— Training and management of staff on good practice.
— PPE is as follows:
— protective chemical resistant gloves (glove material to be specified by the authorisation holder within
the product information);
— protective coverall (at least type 3 or 4, EN 14605) which is impermeable for the biocidal product
shall be worn (coverall material to be specified by the authorisation holder within the product
information);
— Eye protection;
— Substance/task appropriate respirator if ventilation is inadequate.
ELI: http://data.europa.eu/eli/reg_impl/2025/2202/oj 217/227EN
OJ L, 20.11.2025
4.20.3. Where specific to the use, the particulars of likely direct or indirect effects, first aid instructions and emergency measures to
protect the environment
See general directions for use.
4.20.4. Where specific to the use, the instructions for safe disposal of the product and its packaging
See general directions for use.
4.20.5. Where specific to the use, the conditions of storage and shelf-life of the product under normal conditions of storage
See general directions for use.
4.21. Use description
Table 21
Preservation of polymers used in oilfield processes (e.g. enhanced oil recovery, drilling muds, etc.)
Product type PT11: Preservatives for liquid-cooling and processing systems
Where relevant, an exact description of -
the authorised use
Target organism(s) (including Scientific name: no data
development stage) Common name: Bacteria
Development stage: no data
Field(s) of use outdoor use
Preservation of polymers used in oilfield processes (e.g. enhanced oil
recovery, drilling muds, etc.)
Application method(s) Method: -
Detailed description:
-
Application rate(s) and frequency Application Rate:
Preventive treatment of polymers used in the injection water:
Xanthan polymer: 30 -50 g C(M)IT/MIT/m3 solution. HPAM
polymer: 30 - 50 g C(M)IT/MIT/m3 solution. Preventive treatment of
polymers used in the drilling muds: Xanthan polymer: 30 g C(M)IT/
MIT/m3 solution. HPAM polymer: 30 g C(M)IT/MIT/m3 solution.
-
Number and timing of application:
Preventive treatment of polymers used in the injection water:
Xanthan polymer: 30 -50 g C(M)IT/MIT/m3 solution.
HPAM polymer: 30 - 50 g C(M)IT/MIT/m3 solution.
Preventive treatment of polymers used in the drilling muds:
Xanthan polymer: 30 g C(M)IT/MIT/m3 solution.
HPAM polymer: 30 g C(M)IT/MIT/m3 solution.
Category(ies) of users industrial
218/227 ELI: http://data.europa.eu/eli/reg_impl/2025/2202/ojEN
OJ L, 20.11.2025
Pack sizes and packaging material For industrial and professional users:
— HDPE flask: 5 L (nominal)
— HDPE Pail / Jerrycan: 10 L, 20 L, 25 L, 30 L (nominal)
— Box with HDPE liner: 20 L
— HDPE Drum: 110 L, 120 L, 200 L, 260 L
— HDPE IBC: 650 L, 800 L, 1 000 L, 1 250 L
All products should be transport and stored in a vented room.
4.21.1. Use-specific instructions for use
Microbiological tests to prove adequacy of preservation have to be undertaken by the user of C(M)IT/MIT products
in order to determine the effective dose of the preservative for the specific matrix/location/system. If needed,
consult the manufacturer of the preservative product.
4.21.2. Use-specific risk mitigation measures
— Rinse the system (especially the dispensing pumps) with water prior to perform the cleaning step.
— During handling phases (mixing and loading) and cleaning of the dispensing pumps, exposure to the
product (corrosive and skin sensitizer product) has to be limited by use of PPE and application of technical
and organisational RMM:
— Minimisation of manual phases (process automation);
— Use of a dosing device;
— Regular cleaning of equipment and work area;
— Avoidance of contact with contaminated tools and objects;
— Good standard of general ventilation;
— Training and management of staff on good practice.
— PPE is as follows:
— protective chemical resistant gloves (glove material to be specified by the authorisation holder within
the product information);
— protective coverall (at least type 3 or 4, EN 14605) which is impermeable for the biocidal product
shall be worn (coverall material to be specified by the authorisation holder within the product
information);
— Eye protection;
— Substance/task appropriate respirator if ventilation is inadequate.
4.21.3. Where specific to the use, the particulars of likely direct or indirect effects, first aid instructions and emergency measures to
protect the environment
See general directions for use.
4.21.4. Where specific to the use, the instructions for safe disposal of the product and its packaging
See general directions for use.
4.21.5. Where specific to the use, the conditions of storage and shelf-life of the product under normal conditions of storage
See general directions for use.
ELI: http://data.europa.eu/eli/reg_impl/2025/2202/oj 219/227EN
OJ L, 20.11.2025
4.22. Use description
Table 22
Slimicide treatment in the de-inking process of the pulp and paper
Product type PT12: Slimicides
Where relevant, an exact description of -
the authorised use
Target organism(s) (including Scientific name: no data
development stage) Common name: Bacteria
Development stage: no data
Scientific name: no data
Common name: Yeasts
Development stage: no data
Scientific name: no data
Common name: fungi
Development stage: no data
Field(s) of use indoor use
Slimicide treatment in the de-inking process of the pulp and paper.
Recycling paper /deinking paper mills. Deinking process is a
manufacturing paper process of removing printing inks from waste
paper-fibers to produce deinked pulp.
Application method(s) Method: closed system
Detailed description:
Manual and automated dosing. The biocidal product is automatically
dosed by pump and fixed pipes into the circuit, usually in the pulper
below the water level.
Application rate(s) and frequency Application Rate:
Curative treatment: 10 to 14,9 g C(M)IT/MIT (3:1) / m3 of water to
be treated. Preventive treatment: 5 g C(M)IT/MIT (3:1) / m3 of water
to be treated.
-
Number and timing of application:
Curative treatment: 10 to 14,9 g C(M)IT/MIT (3:1) / m3 of water to
be treated
Contact time: 24 hours
Preventive treatment: 5 g C(M)IT/MIT (3:1) / m3 of water to be
treated.
Category(ies) of users industrial
Pack sizes and packaging material For industrial and professional users:
— HDPE flask: 5 L (nominal)
— HDPE Pail / Jerrycan: 10 L, 20 L, 25 L, 30 L (nominal)
— Box with HDPE liner: 20 L
— HDPE Drum: 110 L, 120 L, 200 L, 260 L
— HDPE IBC: 650 L, 800 L, 1 000 L, 1 250 L
All products should be transport and stored in a vented room.
220/227 ELI: http://data.europa.eu/eli/reg_impl/2025/2202/ojEN
OJ L, 20.11.2025
4.22.1. Use-specific instructions for use
Microbiological tests to prove adequacy of preservation have to be undertaken by the user of C(M)IT/MIT products
in order to determine the effective dose of the preservative for the specific matrix/location/system. If needed,
consult the manufacturer of the preservative product.
4.22.2. Use-specific risk mitigation measures
— Rinse the system (especially the dispensing pumps) with water prior to perform the cleaning step.
— During handling phases (mixing and loading) and cleaning of the dispensing pumps, exposure to the
product (corrosive and skin sensitizer product) has to be limited by use of PPE and application of technical
and organisational RMM:
— Minimisation of manual phases (process automation);
— Use of a dosing device;
— Regular cleaning of equipment and work area;
— Avoidance of contact with contaminated tools and objects;
— Good standard of general ventilation;
— Training and management of staff on good practice.
— PPE is as follows:
— protective chemical resistant gloves (glove material to be specified by the authorisation holder within
the product information);
— protective coverall (at least type 3 or 4, EN 14605) which is impermeable for the biocidal product
shall be worn (coverall material to be specified by the authorisation holder within the product
information);
— Eye protection;
— Substance/task appropriate respirator if ventilation is inadequate.
4.22.3. Where specific to the use, the particulars of likely direct or indirect effects, first aid instructions and emergency measures to
protect the environment
See general directions for use.
4.22.4. Where specific to the use, the instructions for safe disposal of the product and its packaging
See general directions for use.
4.22.5. Where specific to the use, the conditions of storage and shelf-life of the product under normal conditions of storage
See general directions for use.
4.23. Use description
Table 23
Slimicide treatment in the wet-end stage of paper manufacturing process
Product type PT12: Slimicides
Where relevant, an exact description of -
the authorised use
ELI: http://data.europa.eu/eli/reg_impl/2025/2202/oj 221/227EN
OJ L, 20.11.2025
Target organism(s) (including Scientific name: no data
development stage) Common name: Bacteria
Development stage: no data
Scientific name: no data
Common name: Yeasts
Development stage: no data
Scientific name: no data
Common name: fungi
Development stage: no data
Field(s) of use indoor use
Slimicide treatment in the wet-end stage of the paper manufacturing
process (paper mills, wet-end stage (water circuits), and paper mills
process system).
Application method(s) Method: closed system
Detailed description:
Manual and automated dosing.
Application rate(s) and frequency Application Rate:
Curative treatment: 10 to 14,9 g C(M)IT/MIT (3:1) / m3 of water to
be treated. Preventive treatment: 5 g C(M)IT/MIT (3:1) / m3 of water
to be treated.
-
Number and timing of application:
Curative treatment: 10 to 14,9 g C(M)IT/MIT (3:1) / m3 of water to
be treated
Contact time: 24 hours
Preventive treatment: 5 g C(M)IT/MIT (3:1) / m3 of water to be
treated.
Category(ies) of users industrial
Pack sizes and packaging material For industrial and professional users:
— HDPE flask: 5 L (nominal)
— HDPE Pail / Jerrycan: 10 L, 20 L, 25 L, 30 L (nominal)
— Box with HDPE liner: 20 L
— HDPE Drum: 110 L, 120 L, 200 L, 260 L
— HDPE IBC: 650 L, 800 L, 1 000 L, 1 250 L
All products should be transport and stored in a vented room.
4.23.1. Use-specific instructions for use
Microbiological tests to prove adequacy of preservation have to be undertaken by the user of C(M)IT/MIT products
in order to determine the effective dose of the preservative for the specific matrix/location/system. If needed,
consult the manufacturer of the preservative product.
4.23.2. Use-specific risk mitigation measures
— Rinse the system (especially the dispensing pumps) with water prior to perform the cleaning step.
— During handling phases (mixing and loading) and cleaning of the dispensing pumps, exposure to the
product (corrosive and skin sensitizer product) has to be limited by use of PPE and application of technical
and organisational RMM:
— Minimisation of manual phases (process automation);
222/227 ELI: http://data.europa.eu/eli/reg_impl/2025/2202/ojEN
OJ L, 20.11.2025
— Use of a dosing device;
— Regular cleaning of equipment and work area;
— Avoidance of contact with contaminated tools and objects;
— Good standard of general ventilation;
— Training and management of staff on good practice.
— PPE is as follows:
— protective chemical resistant gloves (glove material to be specified by the authorisation holder within
the product information);
— protective coverall (at least type 3 or 4, EN 14605) which is impermeable for the biocidal product
shall be worn (coverall material to be specified by the authorisation holder within the product
information);
— Eye protection;
— Substance/task appropriate respirator if ventilation is inadequate.
— The use of C(M)IT/MIT (3:1) containing products for the slimicide treatment in the wet-end stage of the
paper manufacturing process is restricted to
(a) curative treatments in plants connected to a slimicide-free water from a pulp mill and only for the
treatment of the short circulation of the paper mill; and
(b) preventive treatments,
and, for both cases, only if the factory’s waste water is purified in an on-site (full) industrial sewage
treatment plant with a minimal capacity of 5 000 m3per day as described in the Industrial Emission
Directive 2010/75/EU (Best Available Techniques for the production of pulp, paper and board) and if
a dilution of at least 200 times in surface water is achieved after the industrial sewage treatment plant.
4.23.3. Where specific to the use, the particulars of likely direct or indirect effects, first aid instructions and emergency measures to
protect the environment
See general directions for use.
4.23.4. Where specific to the use, the instructions for safe disposal of the product and its packaging
See general directions for use.
4.23.5. Where specific to the use, the conditions of storage and shelf-life of the product under normal conditions of storage
See general directions for use.
4.24. Use description
Table 24
Preventive treatment (biofouling control) online and after cleaning in place for industrial RO/NF
membranes
Product type PT12: Slimicides
Where relevant, an exact description of -
the authorised use
Target organism(s) (including Scientific name: no data
development stage) Common name: Bacteria
Development stage: no data
ELI: http://data.europa.eu/eli/reg_impl/2025/2202/oj 223/227EN
OJ L, 20.11.2025
Field(s) of use indoor use
Preventive treatment (biofouling control) online and after cleaning in
place for industrial RO/NF membranes
Application method(s) Method: closed system
Detailed description:
Manual and automated dosing.Biocidal product application on a
routine basis will prevent biofilm growth on Reverse Osmosis or
Nano Filtration membrane surfaces, feed spacer, filter media and
pipework. The biocidal product should be dispensed to the feed water
at a point to assure adequate mixing throughout the system.
Application rate(s) and frequency Application Rate:
Preventive treatment: 5 g C(M)IT/MIT (3:1) per m3 of fluid
-
Number and timing of application:
Preventive treatment: 5 g C(M)IT/MIT (3:1) per m3 of fluid
Category(ies) of users industrial
Pack sizes and packaging material For industrial and professional users:
— HDPE flask: 5 L (nominal)
— HDPE Pail / Jerrycan: 10 L, 20 L, 25 L, 30 L (nominal)
— Box with HDPE liner: 20 L
— HDPE Drum: 110 L, 120 L, 200 L, 260 L
— HDPE IBC: 650 L, 800 L, 1 000 L, 1 250 L
All products should be transport and stored in a vented room.
4.24.1. Use-specific instructions for use
Microbiological tests to prove adequacy of preservation have to be undertaken by the user of C(M)IT/MIT products
in order to determine the effective dose of the preservative for the specific matrix/location/system. If needed,
consult the manufacturer of the preservative product.
4.24.2. Use-specific risk mitigation measures
— Rinse the system (especially the dispensing pumps) with water prior to perform the cleaning step.
— During handling phases (mixing and loading) and cleaning of the dispensing pumps, exposure to the
product (corrosive and skin sensitizer product) has to be limited by use of PPE and application of technical
and organisational RMM:
— Minimisation of manual phases (process automation);
— Use of a dosing device;
— Regular cleaning of equipment and work area;
— Avoidance of contact with contaminated tools and objects;
— Good standard of general ventilation;
— Training and management of staff on good practice.
224/227 ELI: http://data.europa.eu/eli/reg_impl/2025/2202/ojEN
OJ L, 20.11.2025
— PPE is as follows:
— protective chemical resistant gloves (glove material to be specified by the authorisation holder within
the product information);
— protective coverall (at least type 3 or 4, EN 14605) which is impermeable for the biocidal product
shall be worn (coverall material to be specified by the authorisation holder within the product
information);
— Eye protection;
— Substance/task appropriate respirator if ventilation is inadequate.
— Use product only in premises that are connected to a STP.
4.24.3. Where specific to the use, the particulars of likely direct or indirect effects, first aid instructions and emergency measures to
protect the environment
See general directions for use.
4.24.4. Where specific to the use, the instructions for safe disposal of the product and its packaging
See general directions for use.
4.24.5. Where specific to the use, the conditions of storage and shelf-life of the product under normal conditions of storage
See general directions for use.
5. GENERAL DIRECTIONS FOR USE OF THE META SPC 4
5.1. Instructions for use
— The duration of the effect is dependent on the performance requirements of the customer for their preserved
material and on the specific ingredients composition and pH of the preserved product.
— Always read the label or leaflet before use and follow all the instructions provided.
— Respect the conditions of use of the product (concentration, contact time, temperature, pH, etc.)
PRECAUTIONARY MEASURES DURING STORAGE AND TRANSPORT:
Keep in a well-ventilated place. The product as supplied may evolve gas (largely carbon dioxide) slowly. To prevent
the buildup of pressure the product is packaged in specially vented containers, where necessary. Keep this product
in the original container when not in use. Container must be stored and transported in an upright position to
prevent spilling the contents through the vent, where fitted.
5.2. Risk mitigation measures
-
5.3. Particulars of likely direct or indirect effects, first aid instructions and emergency measures to protect
the environment
— Skin contact: Remove contaminated clothing and shoes. Wash contaminated skin with water. Contact
poison treatment specialist if symptoms occur.
— Eye contact: Immediately flush with plenty of water, occasionally lifting the upper and lower eyelids. Check
for and remove any contact lenses if easy to do. Continue to rinse with tepid water for at least 30 minutes.
Call 112/ambulance for medical assistance.
ELI: http://data.europa.eu/eli/reg_impl/2025/2202/oj 225/227EN
OJ L, 20.11.2025
— Ingestion: Wash out mouth with water. Contact poison treatment specialist. Seek medical advice
immediately if symptoms occur and/or large quantities have been ingested. Do not give fluids or induce
vomiting.
— Inhalation (of spray mist): Remove victim to fresh air and keep at rest in a position comfortable for
breathing. Seek medical advice immediately if symptoms occur and/or large quantities have been inhaled.
— In case of impaired consciousness place in recovery position and seek medical advice immediately.
— Keep the container or label available.
5.4. Instructions for safe disposal of the product and its packaging
— Do not discharge unused product on the ground, into water courses, into pipes (e.g. sink, toilets) nor down
the drains.
— Dispose of unused product, its packaging and all other waste, in accordance with local regulations.
5.5. Conditions of storage and shelf-life of the product under normal conditions of storage
Conditions for safe storage, including any incompatibilities: Keep in a dry, cool and well-ventilated place, in the
original container.
Shelf-life: 24 months
Protect from sunlight.
Recommendation: If a metal packaging is used, a varnish layer should be applied.
6. OTHER INFORMATION
-
7. THIRD INFORMATION LEVEL: INDIVIDUAL PRODUCTS IN THE META SPC 4
7.1. Trade name(s), authorisation number and specific composition of each individual product
Trade name(s) KATHON™ Market area: EU
LX 300
BIOCIDE
KATHON™ Market area: EU
WT 300
Biocide
ACQ 819 Market area: EU
Biocide Market area: EU
KT300WT
KT300WT Market area: EU
KT300LX Market area: EU
SANITER 454 Market area: EU
OS Isobio3 Market area: EU
Authorisation number EU-0025449-0012 1-4
226/227 ELI: http://data.europa.eu/eli/reg_impl/2025/2202/ojEN
OJ L, 20.11.2025
Common name IUPAC name Function CAS number EC number Content (%)
C(M)IT/MIT Reaction mass Active substance 55965-84-9 4,6 % (w/w)
(3:1) of 5-chloro-
2-methyl-2h-
isothiazol-
3-one
and 2-methyl-
2h-isothiazol-
3-one (3:1)
7.2. Trade name(s), authorisation number and specific composition of each individual product
Trade name(s) KATHON™ Market area: EU
WT 150
Biocide
KATHON™ Market area: EU
LX 150
BIOCIDE
BIO 419 Market area: EU
SANITER 420 Market area: EU
Authorisation number EU-0025449-0013 1-4
Common name IUPAC name Function CAS number EC number Content (%)
C(M)IT/MIT Reaction mass Active substance 55965-84-9 2,3 % (w/w)
(3:1) of 5-chloro-
2-methyl-2h-
isothiazol-
3-one
and 2-methyl-
2h-isothiazol-
3-one (3:1)
ELI: http://data.europa.eu/eli/reg_impl/2025/2202/oj 227/227
            

Continue your research

Get AI Summary & Executive Breakdown

Chat with this Document

Search across full 480K+ policy library

Commission Implementing Regulation (EU) 2025/2202 of 22 October 2025 amending Implementing Regulation (EU) 2022/1434 as regards administrative changes to the Union authorisation for the biocidal product family CMIT-MIT Aqueous 1.5-15, and correcting that Regulation

Executive Summary & Key Takeaways

Key Entities Referenced

Continue your research

Related Documents from European Commission