Regulation No 51 of the Economic Commission for Europe of the United Nations (UNECE) — Uniform provisions concerning the approval of motor vehicles having at least four wheels with regard to their sound emissions [2018/798]

4.6.2018 EN Official Journal of the European Union L 138/1 II (Non-legislative acts) ACTS ADOPTED BY BODIES CREATED BY INTERNATIONAL AGREEMENTS Only the original UN/ECE texts have legal effect under international public law. The status and date of entry into force of this Regulation should be checked in the latest version of the UN/ECE status document TRANS/WP.29/343, available at: http://www.unece.org/trans/main/wp29/wp29wgs/wp29gen/wp29fdocstts.html Regulation No 51 of the Economic Commission for Europe of the United Nations (UNECE) — Uniform provisions concerning the approval of motor vehicles having at least four wheels with regard to their sound emissions [2018/798] Incorporating all valid text up to: Supplement 2 to the 03 series of amendments — Date of entry into force: 10 February 2018 CONTENTS REGULATION 1. Scope 2. Definitions 3. Application for approval 4. Markings 5. Approval 6. Specifications 7. Modification and extension of approval of a vehicle type 8. Conformity of production 9. Penalties for non-conformity of production 10. Production definitively discontinued 11. Transitional provisions 12. Names and addresses of Technical Services responsible for conducting approval tests and of Type Approval Authorities Annexes 1 Communication Appendix 1 — Addendum to the communication form No … Appendix 2 — Technical Information Document 2 Arrangements of the approval mark 3 Methods and instruments for measuring the sound made by motor vehicles AppendixL 138/2 EN Official Journal of the European Union 4.6.2018 4 Exhaust silencing systems containing acoustically absorbing fibrous materials Appendix 5 Compressed air noise Appendix 6 Checks on conformity of production 7 Measuring method to evaluate compliance with the Additional Sound Emission Provisions Appendix 1 — Statement of Compliance with the Additional Sound Emission Provisions Appendix 2 1. SCOPE This Regulation contains provisions on the sound emitted by motor vehicles and applies to vehicles of categories M and N (1). The specifications in this Regulation are intended to reproduce the sound levels which are generated by vehicles during normal driving in urban traffic. 2. DEFINITIONS For the purpose of this Regulation, 2.1. ‘Approval of a vehicle’ means the approval of a vehicle type with regard to sound; 2.2. ‘Vehicle type’ means a category of motor vehicles which do not differ in such essential respects as: 2.2.1. For vehicles tested according to Annex 3, paragraph 3.1.2.1: 2.2.1.1. The shape or materials of the engine compartment and its soundproofing; 2.2.1.2. The type of engine (positive or compression ignition, two- or four-stroke, reciprocating or rotary piston), number and capacity of cylinders, number and type of carburettors or injection system, arrangement of valves, or the type of electric motor; 2.2.1.3. Rated maximum net power and corresponding rated engine speed(s); however if the rated maximum net power and the corresponding rated engine speed differs only due to different engine mappings, these vehicles may be regarded as from the same type; 2.2.1.4. The silencing system. 2.2.2. For vehicles tested according to Annex 3, paragraph 3.1.2.2: 2.2.2.1. The shape or materials of the engine compartment and its soundproofing; 2.2.2.2. The type of engine (positive or compression ignition, two- or four-stroke, reciprocating or rotary piston), number and capacity of cylinders, type of injection system, arrangement of valves, rated engine speed (S), or the type of electric motor; 2.2.2.3. Vehicles having the same type of engine and/or different overall gear ratios may be regarded as vehicles of the same type; 2.3. However, if the differences in paragraph 2.2.2 provide for different target conditions, as described in paragraph 3.1.2.2 of Annex 3, these differences are to be considered as a change of type; (1) As defined in the Consolidated Resolution on the Construction of Vehicles (R.E.3), document ECE/TRANS/WP.29/78/Rev.3, para. 2 — www.unece.org/trans/main/wp29/wp29wgs/wp29gen/wp29resolutions.html4.6.2018 EN Official Journal of the European Union L 138/3 2.4. ‘Mass of a vehicle in running order (m )’ means ro (a) In the case of a motor vehicle: The mass of the vehicle, with its fuel tank(s) filled to at least 90 per cent of its or their capacity/ies, including the mass of the driver, of the fuel and liquids, fitted with the standard equipment in accordance with the manufacturer's specifications and, when they are fitted, the mass of the bodywork, the cabin, the coupling and the spare wheel(s) as well as the tools; (b) In the case of a trailer: The mass of the vehicle including the fuel and liquids, fitted with the standard equipment in accordance with the manufacturer's specifications, and, when they are fitted, the mass of the bodywork, additional coupling(s), the spare wheel(s) and the tools. 2.5. ‘Technically permissible maximum laden mass (M)’ means the maximum mass allocated to a vehicle on the basis of its construction features and its design performances; the technically permissible laden mass of a trailer or of a semi-trailer includes the static mass transferred to the towing vehicle when coupled; 2.6. ‘Vehicle length’ means a dimension which is measured according to ISO standard 612-1978, term No 6.1. In addition to the provisions of that standard, when measuring the vehicle structural length the following devices shall not be taken into account: (a) Wiper and washer devices; (b) Front or rear marker-plates; (c) Customs sealing devices and their protection; (d) Devices for securing the tarpaulin and their protection; (e) Lighting equipment; (f) Rear view mirrors; (g) Rear space watching aids; (h) Air-intake pipes; (i) Length stops for demountable bodies; (j) Access steps; (k) Ram rubbers; (l) Lifting platforms, access ramps and similar equipment in running order, not exceeding 200 mm, provided that the loading capacity of the vehicle is not increased; (m) Coupling devices for motor vehicles. 2.7. ‘Vehicle width’ means a dimension which is measured according to ISO standard 612-1978, term No 6.2. In addition to the provisions of that standard, when measuring the vehicle structural width the following devices shall not be taken into account: (a) Customs sealing devices and their protection; (b) Devices for securing the tarpaulin and their protection; (c) Tyre failure tell-tale devices; (d) Protruding flexible parts of a spray-suppression system; (e) Lighting equipment. 2.8. ‘Rated maximum net power, P ’ means the engine power expressed in kW and measured by the method n pursuant to Regulation No 85. 2.8.1. ‘Total engine power’ means the sum of all power from available propulsion sources. 2.9. ‘Rated engine speed, S’ means the declared engine speed in min– 1 (rpm) at which the engine develops its rated maximum net power pursuant to Regulation No 85 or, where the rated maximum net power is reached at several engine speeds, the highest one of those speeds.L 138/4 EN Official Journal of the European Union 4.6.2018 2.10. ‘Power to Mass Ratio index (PMR)’ means a numerical quantity (see Annex 3, paragraph 3.1.2.1.1) with no dimension used for the calculation of acceleration. 2.11. ‘Reference point’ means one of the following points: 2.11.1. In the case of vehicles of categories M , N and M ≤ 3 500 kg technically permissible maximum laden mass: 1 1 2 (a) For front engine vehicles: the front end of the vehicle; (b) For mid-engine vehicles: the centre of the vehicle; (c) For rear engine vehicles: the rear end of the vehicle. 2.11.2. In the case of vehicles of categories M > 3 500 kg technical permissible maximum laden mass, M , N , N : 2 3 2 3 (a) For front-engine vehicles, the front end of the vehicle; (b) For all other vehicles, the border of the engine closest to the front of the vehicle; 2.12. ‘Engine’ means the power source without detachable accessories. Power source includes in this context all sources of motive power; for example, electric or hydraulic power sources used alone or in combination with other power sources. 2.13. ‘Target acceleration’ means acceleration at a partial throttle condition in urban traffic and is derived from statistical investigations. 2.14. ‘Reference acceleration’ means the required acceleration during the acceleration test on the test track. 2.15. ‘Gear ratio weighting factor k’ means a dimensionless numerical quantity used to combine the test results of two gear ratios for the acceleration test and the constant speed test. 2.16. ‘Partial power factor k’ means a numerical quantity with no dimension used for the weighted combination of p the test results of the acceleration test and the constant speed test for vehicles. 2.17. ‘Pre-acceleration’ means application of acceleration control device prior to AA′ for the purpose of achieving stable acceleration between AA′ and BB′ as referred to in Figure 1 of the Appendix to Annex 3. 2.18. Gear (1) 2.18.1. ‘Gear ratios’ 2.18.1.1. ‘Internal gearbox ratio’ means the ratios of engine to gearbox output shaft revolutions. 2.18.1.2. ‘Final drive ratio’ means the ratio(s) of gearbox output shaft to driven wheel revolutions. 2.18.1.3. ‘Total gear ratio’ means the ratios between vehicle speed and engine speed during the passage of the vehicle through the test track. 2.18.1.4. ‘Gear ratio’ used in context with vehicles tested according to 3.1.2.1 of Annex 3 and Annex 7 is the total gear ratio as defined in 2.18.1.3 above. 2.18.2. ‘Locked gear ratio’ means the control of the transmission such that the gear will not change during a test. 2.18.3. ‘Gear’ means in the context of this Regulation a discrete gear ratio either selectable by the driver or by an external device. 2.18.4. For vehicles tested according 3.1.2.1 of Annex 3 and Annex 7, ‘gear’ and ‘gear ’ are defined as two gears i i + 1 in sequence, where gear either provides an acceleration within the 5 per cent tolerance according to i paragraph 3.1.2.1.4.1(a) of Annex 3 or an acceleration greater than the reference acceleration, and gear an i + 1 acceleration lower than the reference acceleration according to paragraph 3.1.2.1.4.1(b) or (c) of Annex 3. (1) The common understanding of a ‘low gear’ or a ‘high gear’ shall not apply to gear ratios. For example, the lowest gear for forward driving, the first gear, has the highest gear ratio of all forward driving gears. While manual transmission has discrete gears, many non-manual transmissions can have more gear ratios engaged by the control unit of the transmission.4.6.2018 EN Official Journal of the European Union L 138/5 2.19. ‘Silencing system’ means a complete set of components necessary for limiting the sound produced by an engine, its intake and its exhaust (the exhaust manifold(s), the catalyst(s) and emission after-treatment device(s) are not considered part of the silencing system; these parts belong to the engine). 2.20. ‘Design family of exhaust silencing system or exhaust silencing system components’ means a group of silencing systems or components thereof in which all of the following characteristics are the same: (a) The presence of net gas flow of the exhaust gases through the absorbing fibrous material when in contact with that material; (b) The type of the fibres; (c) Where applicable, binder material specifications; (d) Average fibre dimensions; (e) Minimum bulk material packing density in kg/m3; (f) Maximum contact surface between the gas flow and the absorbing material. 2.21. ‘Exhaust silencing system of different types’ means silencing systems which significantly differ in respect of at least one of the following: (a) Trade names or trademarks of their components; (b) The characteristics of the materials constituting their components, except for the coating of those components; (c) The shape or size of their components; (d) The operating principles of at least one of their components; (e) The assembly of their components; (f) The number of exhaust silencing systems or components. 2.22. ‘Replacement silencing system’ means any part of the silencing system or its components intended for use on a vehicle, other than a part of the type fitted to this vehicle when submitted for type-approval pursuant to this Regulation. 2.23. ‘R-point’ means R-point as defined in paragraph 2.4 of Annex 1 to the Consolidated Resolution on the Construction of Vehicles (R.E.3). 2.24. Table of symbols Symbol Unit Annex Paragraph Explanation m kg Annex 3 2.2.1 mass in running order; value to be ro reported and used for calculations to a precision of 10 kg m kg Annex 3 2.2.1 test mass of the vehicle; value to be t reported and used for calculations to a precision of 10 kg m kg Annex 3 2.2.1 target mass of the vehicle target m kg Annex 3 2.2.1 extra loading xload m kg Annex 3 2.2.1 front axle load in unladen condition fa load unladen mr kg Annex 3 2.2.1 rear axle load in unladen condition a load unladen m kg Annex 3 2.2.1 unladen vehicle mass unladenL 138/6 EN Official Journal of the European Union 4.6.2018 Symbol Unit Annex Paragraph Explanation m kg Annex 3 2.2.1 Technically permissible maximum la­ ac ra max den mass allowed for the rear axle as declared by the manufacturer m kg Annex 3 2.2.1 mass of driver d m kg Annex 3 2.2.1 mass of the incomplete vehicle (M or chassis M2M3 2 M ) 3 m kg Annex 3 2.2.1 extra load to be added to the incom­ xload M2M3 plete vehicle (M or M ) to reach the 2 3 mass of the vehicle in running order as chosen by the manufacturer m kg Annex 3 2.2.7.2 front axle load in laden condition fa load laden m kg Annex 3 2.2.7.2 rear axle load in laden condition ra load laden AA′ — Annex 3 3.1.1 line perpendicular to vehicle travel which indicates beginning of zone in which to record sound pressure level during test BB′ — Annex 3 3.1.1 line perpendicular to vehicle travel which indicates end of zone in which to record sound pressure level during test CC′ — Annex 3 3.1.1 line of vehicle travel through test sur­ face defined in ISO 10844 PP′ — Annex 3 3.1.1 line perpendicular to vehicle travel which indicates location of micro­ phones v km/h Annex 3 3.1.2.1 vehicle test speed test PMR — Annex 3 3.1.2.1.1 power-to-mass ratio index to be used for calculations; value to be reported and used for calculations to the first decimal place P kW Annex 3 3.1.2.1.1 rated total engine net power n l m Annex 3 3.1.2.1.2 reference length; value to be reported and used for calculations to a precision of 0,01 m (1 cm) l m Annex 3 3.1.2.1.2 length of vehicle; value to be reported veh and used for calculations to a precision of 0,01 m (1 cm) v km/h Annex 3 3.1.2.1.2 vehicle velocity when reference point AA′ passes line AA′ (see 5.1 for definition of reference point); value to be re­ ported and used for calculations to the first decimal place4.6.2018 EN Official Journal of the European Union L 138/7 Symbol Unit Annex Paragraph Explanation v km/h Annex 3 3.1.2.1.2 vehicle velocity when reference point BB′ or rear of vehicle passes line BB′ (see 5.1 for definition of reference point); value to be reported and used for cal­ culations to the first decimal place v km/h Annex 3 3.1.2.1.2 vehicle velocity when reference point PP′ passes line PP′ (see 5.1 for definition of reference point); value to be re­ ported and used for calculations to the first decimal place a m/s2 Annex 3 3.1.2.1.2.1 acceleration at wide-open throttle wot test from AA′ to BB′; value to be reported and used for calculations to the sec­ ond decimal place a m/s2 Annex 3 3.1.2.1.2.1 acceleration at wide-open throttle wot test,i achieved in a particular gear i; value to be reported and used for calcula­ tions to the second decimal place l m Annex 3 3.1.2.1.2.1 point of depressing the accelerator be­ pa fore line AA′; value to be reported in full meter a m/s2 Annex 3 3.1.2.1.2.2 acceleration at wide-open throttle wot test, PP-BB from PP′ to BB′; value to be reported and used for calculations to the sec­ ond decimal place a m/s2 Annex 3 3.1.2.1.2.3 target acceleration representing urban urban traffic acceleration; value to be re­ ported and used for calculations to the second decimal place a m/s2 Annex 3 3.1.2.1.2.4 reference acceleration for the wide- wot ref open-throttle test; value to be re­ ported and used for calculations to the second decimal place k — Annex 3 3.1.2.1.3 partial power factor; value to be re­ P ported and used for calculations to the second decimal place a m/s2 Annex 3 3.1.2.1.4.1 acceleration at wide-open-throttle in wot i gear ratio i; value to be reported and used for calculations to the second decimal place a m/s2 Annex 3 3.1.2.1.4.1 acceleration at wide-open-throttle in wot (i + 1) gear ratio (i + 1); value to be reported and used for calculations to the sec­ ond decimal place gear ratio i — Annex 3 3.1.2.1.4.1 first of two gear ratios for use in the vehicle testL 138/8 EN Official Journal of the European Union 4.6.2018 Symbol Unit Annex Paragraph Explanation gear ratio i + 1 — Annex 3 3.1.2.1.4.1 second of two gear ratios, with an en­ gine speed lower than gear ratio i k — Annex 3 3.1.2.1.4.1 gear ratio weighting factor; value to be reported and used for calculations to the second decimal place n 1/min Annex 3 3.1.2.2 engine rotational speed of the vehicle, BB′ when the reference point passes BB′; value to be reported and used for cal­ culations to a precision of 10 min– 1 S 1/min Annex 3 3.1.2.2 rated engine rotational speed in revs per minute, synonymous with the en­ gine rotational speed at maximum power n 1/min Annex 3 3.1.2.2.1.1(a) target engine rotational speed of the target BB′ vehicle when the reference point has to pass line BB′ (see 2.11.2 for definit­ ion of reference point) v km/h Annex 3 3.1.2.2.1.1(a) target vehicle velocity when it is ne­ target BB′ cessary that the reference point has to pass line BB′ (see 2.11.2 for definition of reference point) v km/h Annex 3 3.1.2.2.1.1(b) target vehicle velocity when certain BB′ gear I conditions are met v km/h Annex 3 3.1.2.2.1.1(c) target vehicle velocity when certain BB′ gear i, i = 1,2 conditions are met gear — Annex 3 3.1.2.2.1.1(d) first of two gear ratios used for testing x of M having a maximum authorised 2 mass of more than 3 500 kg, M , N , 3 2 and N where certain criteria on test 3 conditions are met gear — Annex 3 3.1.2.2.1.1(d) second of two gear ratios used for y testing of M having a maximum 2 authorised mass of more than 3 500 kg, M , N , and N where cer­ 3 2 3 tain criteria on test conditions are met v km/h Annex 3 3.1.2.2.1.1(d) target vehicle velocity when certain BB′x conditions are met v km/h Annex 3 3.1.2.2.1.1(d) target vehicle velocity when certain BB′y conditions are met v km/h Annex 3 3.1.2.2.1.2(b) target vehicle velocity when certain BB′1 conditions are met v km/h Annex 3 3.1.2.2.1.2(b) target vehicle velocity when certain BB′2 conditions are met4.6.2018 EN Official Journal of the European Union L 138/9 Symbol Unit Annex Paragraph Explanation n , i = 1,2 1/min Annex 3 3.1.2.2.1.2(d) engine rotational speed when the re­ BB′i ference point passes BB′ when certain conditions are met L dB(A) Annex 3 3.1.3.1 vehicle sound pressure level at con­ crs i stant speed test for gear i; value to be reported and used for calculations to the first decimal place L dB(A) Annex 3 3.1.3.1 vehicle sound pressure level at con­ crs (i + 1) stant speed test for gear (i + 1); value to be reported and used for calcula­ tions to the first decimal place L dB(A) Annex 3 3.1.3.1 reported vehicle sound pressure level crs rep at constant speed test; value to be re­ ported and used for calculations to the first decimal place L dB(A) Annex 3 3.1.3.1. vehicle sound pressure level at wide- wot i open-throttle test for gear i; value to be reported and used for calculations to the first decimal place L dB(A) Annex 3 3.1.3.1 vehicle sound pressure level at wide- wot (i + 1) open-throttle test for gear (i + 1); value to be reported and used for cal­ culations to the first decimal place L dB(A) Annex 3 3.1.3.1 reported vehicle sound pressure level wot rep at wide-open-throttle; value to be re­ ported and used for calculations to the first decimal place L dB(A) Annex 3 3.1.3.1 reported vehicle sound pressure level urban representing urban operation; value to be reported mathematically rounded to the nearest integer a m/s2 Annex 7 2.3 maximum required acceleration at wot_ASEP wide-open-throttle κ — Annex 7 2.3 gears to be tested under ‘Additional Sound Emission Provisions’ (ASEP) n 1/min Annex 7 2.3 maximum test engine speed; value to BB_ASEP be reported and used for calculations to a precision of 10 min– 1 v km/h Annex 7 2.3 target vehicle velocity for test point P1 AA′_ASEP of the assessment method according paragraph 2.4 v km/h Annex 7 2.3 target vehicle velocity for test point P4 BB′_ASEP of the assessment method according paragraph 2.4 P — Annex 7 2.4 test point(s) under ASEP jL 138/10 EN Official Journal of the European Union 4.6.2018 Symbol Unit Annex Paragraph Explanation j — Annex 7 2.4 index for the test points under ASEP v km/h Annex 7 2.4 vehicle test speed at BB′ for a particu­ BB_j lar ASEP test point a m/s2 Annex 7 2.5 acceleration at wide-open throttle wot,test, κj achieved in gear κ and at test point j L dB(A) Annex 7 2.5 sound pressure level measured for wot,κj a gear κ and at a test point j; value to be reported and used for calculations to the first decimal place n 1/min Annex 7 2.5 vehicle test engine speed at BB′ for BB,κj a gear κ and at test point j v km/h Annex 7 2.5 vehicle test speed at AA′ for a gear κ AA,κj and at test point j; value to be re­ ported and used for calculations to the first decimal place v km/h Annex 7 2.5 vehicle test speed at BB′ for a gear κ BB,κj and at test point j; value to be re­ ported and used for calculations to the first decimal place v km/h Annex 7 2.5 vehicle test speed at PP′ for a gear κ PP,κj and at test point j; value to be re­ ported and used for calculations to the first decimal place L dB(A) Annex 7 3.1 reported vehicle sound pressure level anchor for gear ratio i from Annex 3; value to be reported and used for calcula­ tions to the first decimal place n 1/min Annex 7 3.1 reported vehicle engine speed for gear anchor,κ ratio i from Annex 3 v km/h Annex 7 3.1 reported vehicle test speed for gear ra­ anchor,κ tio i at BB′ from Annex 3; value to be reported and used for calculations to the first decimal place L dB(A) Annex 7 3.5 sound pressure level measured for κj a gear κ and at a test point j; value to be reported and used for calculations to the first decimal place k — Annex 7 4.2.1 partial power factor determined for P_ASEP the L principle of ASEP urban L dB(A) Annex 7 4.2.1 vehicle sound pressure level measured wot_ASEP for the L principle of ASEP; value urban to be reported and used for calcula­ tions to the first decimal place4.6.2018 EN Official Journal of the European Union L 138/11 Symbol Unit Annex Paragraph Explanation L dB(A) Annex 7 4.2.1 interim result for calculation of urban_measured_ASEP ΔL ; value to be reported and urban_ASEP used for calculations to the first deci­ mal place L dB(A) Annex 7 4.2.1 interim result for calculation of urban_normalised ΔL ; value to be reported and urban_ASEP used for calculations to the first deci­ mal place L dB(A) Annex 7 5.3 reference sound pressure level for re­ ref ference sound assessment; value to be reported and used for calculations to the first decimal place n 1/min Annex 7 5.3 reference engine speed for reference ref_κ sound assessment v km/h Annex 7 5.3 reference vehicle test speed for ref reference sound assessment n 1/min Annex 7 5.3 reference vehicle test engine speed for BB′_ref reference sound assessment v km/h Annex 7 5.3 reference vehicle test speed for BB′_ref reference sound assessment* L dB(A) Annex 7 6.2 estimated urban sound pressure level urban_ASEP determined for the L principle of urban ASEP; value to be reported and used for calculations to the first decimal place 2.25. Modes 2.25.1. ‘Mode’ means a distinct driver-selectable condition which does affect the sound emission of the vehicle. 2.26. Stable acceleration 2.26.1. ‘Stable acceleration’ applicable when acceleration needs to be calculated is given when the acceleration ratio between a and a is less than or equal to 1,2. wot_testPP-BB wot test 2.26.2. ‘Unstable acceleration’ means a deviation from the stable acceleration during acceleration. 2.26.2.1. Unstable acceleration might occur as well during the start of acceleration from low speeds when the powertrain will react by bumping and jerking on the acceleration request. 3. APPLICATION FOR APPROVAL 3.1. The application for approval of a vehicle type with regard to sound shall be submitted by its manufacturer or by his duly accredited representative. 3.2. It shall be accompanied by the undermentioned documents and the following particulars in triplicate: 3.2.1. A description of the vehicle type with regard to the items mentioned in paragraph 2.2 above. The numbers and/or symbols identifying the engine type and the vehicle type shall be specified; 3.2.2. A list of the components, duly identified, constituting the sound reduction system; 3.2.3. A drawing of the assembled sound reduction system and an indication of its position on the vehicle;L 138/12 EN Official Journal of the European Union 4.6.2018 3.2.4. Detailed drawings of each component to enable it to be easily located and identified, and a specification of the materials used. 3.2.5. A technical information document including the information as outlined in Annex 1, Appendix 2. 3.3. In the case of paragraph 2.2.2 the single vehicle, representative of the type in question, will be selected by the Technical Service conducting approval tests, in accordance with the vehicle manufacturer, as that with the lowest mass in running order with the shortest length and following the specification laid down in paragraph 3.1.2.2 in Annex 3. 3.4. At the request of the Technical Service conducting approval tests, the vehicle manufacturer shall, in addition, submit a sample of the sound reduction system and an engine of at least the same cylinder capacity and rated maximum net power as that fitted to the vehicle in respect of which type-approval is sought. 3.5. The Type Approval Authority shall verify the existence of satisfactory arrangements for ensuring effective control of the conformity of production before type approval is granted. 4. MARKINGS 4.1. The components of the sound reduction system, excluding fixing hardware and piping, shall bear: 4.1.1. The trade name or mark of the manufacturer of the sound reduction system and of its components; and 4.1.2. The manufacturer's trade description; 4.2. These markings shall be clearly legible and be indelible even after fitting. 4.3. A component may carry several approval numbers if it has been approved as component of several replacement silencing systems. 5. APPROVAL 5.1. Type approval shall only be granted if the vehicle type meets the requirements of paragraphs 6 and 7 below. 5.2. An approval number shall be assigned to each type approved. Its first two digits (at present 03 corresponding to the 03 series of amendments) shall indicate the series of amendments incorporating the most recent major technical amendments made to the Regulation at the time of issue of the approval. The same Contracting Party shall not assign the same number to another vehicle type. 5.3. Notice of approval or of extension or of refusal or withdrawal of approval or of production definitively discontinued of a vehicle type pursuant to this Regulation shall be communicated to the Parties to the Agreement applying this Regulation, by means of a form conforming to the model in Annex 1 to this Regulation. 5.4. There shall be affixed, conspicuously and in a readily accessible place specified on the approval form, to every vehicle conforming to a vehicle type approved under this Regulation an international approval mark consisting of: 5.4.1. A circle surrounding the letter ‘E’ followed by the distinguishing number of the country which has granted approval (1); 5.4.2. The number of this Regulation, followed by the letter ‘R’, a dash and the approval number to the right of the circle prescribed in paragraph 5.4.1. 5.5. If the vehicle conforms to a vehicle type approved under one or more other Regulations annexed to the Agreement, in the country which has granted approval under this Regulation, the symbol prescribed in paragraph 5.4.1 need not be repeated; in such a case the regulation and approval numbers and the additional symbols of all the Regulations under which approval has been granted in the country which has granted approval under this Regulation shall be placed in vertical columns to the right of the symbol prescribed in paragraph 5.4.1. 5.6. The approval mark shall be clearly legible and be indelible. (1) The distinguishing numbers of the Contracting Parties to the 1958 Agreement are reproduced in Annex 3 to the Consolidated Resolution on the Construction of Vehicles (R.E.3), document ECE/TRANS/WP.29/78/Rev. 3, Annex 3 — www.unece. org/trans/main/wp29/wp29wgs/wp29gen/wp29resolutions.html4.6.2018 EN Official Journal of the European Union L 138/13 5.7. The approval mark shall be placed close to or on the vehicle data plate affixed by the manufacturer. 5.8. Annex 2 to this Regulation gives examples of arrangements of the approval mark. 6. SPECIFICATIONS 6.1. General specifications 6.1.1. The vehicle, its engine and its sound reduction system shall be so designed, constructed and assembled as to enable the vehicle, in normal use, despite the vibration to which it may be subjected, to comply with the provisions of this Regulation. 6.1.2. The sound reduction system shall be so designed, constructed and assembled as to be able to reasonably resist the corrosive phenomena to which it is exposed having regard to the conditions of use of the vehicle, including regional climate differences. 6.2. Specifications regarding sound levels 6.2.1. Methods of measurement 6.2.1.1. The sound made by the vehicle type submitted for approval shall be measured by the methods described in Annex 3 to this Regulation for the vehicle in motion and for the vehicle when stationary (1); in the case of a vehicle where an internal combustion engine cannot operate when the vehicle is stationary, the emitted sound shall only be measured in motion. In the case of a hybrid electrical vehicle of category M1 where an internal combustion engine cannot operate when the vehicle is stationary, the emitted sound shall be measured according to Annex 3, paragraph 4. Vehicles having a technically maximum permissible laden mass exceeding 2 800 kg shall be subjected to an additional measurement of the compressed air noise with the vehicle stationary in accordance with the specifications of Annex 5, if the corresponding brake equipment is part of the vehicle. 6.2.1.2. The values measured in accordance with the provisions of paragraph 6.2.1.1 above shall be entered in the test report and a certificate corresponding to the model shown in Annex 1. 6.2.2. Sound level limits The sound level measured in accordance with the provisions of paragraph 3.1 of Annex 3 to this Regulation, mathematically rounded to the nearest integer value, shall not exceed the following limits: Limit Values (dB(A)) Vehicles used for the carriage of Vehicle category passengers Phase 1 Phase 2 Phase 3 M PMR ≤ 120 72 70 68 1 120 < PMR ≤ 160 73 71 69 PMR > 160 75 73 71 PMR > 200, No of seats ≤ 4, R-point 75 74 72 height < 450 mm from the ground M M ≤ 2,5 t 72 70 69 2 2,5 t < M ≤ 3,5 t 74 72 71 M > 3,5 t; P ≤ 135 kW 75 73 72 n M > 3,5 t; P > 135 kW 75 74 72 n (1) A test is made on a stationary vehicle in order to provide a reference value for administrations which use this method to check vehicles in use.L 138/14 EN Official Journal of the European Union 4.6.2018 Limit Values (dB(A)) Vehicles used for the carriage of Vehicle category passengers Phase 1 Phase 2 Phase 3 M P ≤ 150 kW 76 74 73 3 n 150 kW < P ≤ 250 kW 78 77 76 n P > 250 kW 80 78 77 n Vehicle category Vehicles used for the carriage of goods Phase 1 Phase 2 Phase 3 N M ≤ 2,5 t 72 71 69 1 M > 2,5 t 74 73 71 N P ≤ 135kW 77 75 74 2 n P > 135 kW 78 76 75 n N P ≤ 150 kW 79 77 76 3 n 150 kW < P ≤ 250 kW 81 79 77 n P > 250 kW 82 81 79 n 6.2.2.1. For vehicle types of category M derived from N vehicle types having a technically permissible maximum 1 1 laden mass above 2,5 tons and a R-point height greater than 850 mm from the ground, the limits of vehicle types of category N having a technically permissible maximum laden mass above 2,5 tons apply. 1 6.2.2.2. For vehicle types designed for off-road (1) use, the limit values shall be increased by 2 dB(A) for M and N 3 3 vehicles category and 1 dB(A) for any other vehicle category. For vehicle types of category M the increased limit values for off-road vehicles are only valid if the 1 technically permissible maximum laden mass > 2 tons. 6.2.2.3. Limit values shall be increased by 2 dB(A) for wheelchair accessible vehicles of category M constructed or 1 converted specifically so that they accommodate one or more persons seated in their wheelchairs when travelling on the road, and armoured vehicles, as defined in paragraph 2.5.2 of R.E.3. 6.2.2.4. For vehicle types of category M having a gasoline only engine, the applicable limit value is increased by 3 2 dB(A). 6.2.2.5. For vehicle types of category N having a technically permissible maximum laden mass of less than or equal 1 to 2,5 tons, the engine capacity not exceeding 660 cc and the power-to-mass ratio (PMR) calculated by using the technically permissible maximum laden mass not exceeding 35 and a horizontal distance ‘d’ between the front axle and the driver's seat R point of less than 1 100 mm, the limits of the vehicle types of category N 1 having a technically permissible maximum laden mass above 2,5 tons apply. 6.2.3. Additional sound emission provisions The Additional Sound Emission Provisions (ASEP) apply only to vehicles of categories M and N equipped 1 1 with an internal combustion engine. (1) As defined in the Consolidated Resolution on the Construction of Vehicles (R.E.3), document ECE/TRANS/WP.29/78/Rev.3, para. 2 — www.unece.org/trans/main/wp29/wp29wgs/wp29gen/wp29resolutions.html4.6.2018 EN Official Journal of the European Union L 138/15 Vehicles are deemed to fulfil the requirements of Annex 7, if the vehicle manufacturer provides technical documents to the type approval authority showing, that the difference between maximum and minimum engine speed of the vehicles at BB′ for any test condition inside the ASEP control range defined in paragraph 3.3 of Annex 7 to this Regulation (including Annex 3 conditions) does not exceed 0,15 × S. This article is intended especially for non-lockable transmissions with variable gear ratios (CVT). Vehicles are exempted from ASEP if one of the following conditions is fulfilled: (a) For vehicles of category N , if the engine capacity does not exceed 660 cc and the power-to-mass ratio 1 PMR calculated by using the technically permissible maximum laden mass does not exceed 35. (b) For vehicles of category N , if the payload is at least 850 kg and the power-to-mass ratio calculated by 1 using the technically permissible maximum laden mass does not exceed 40. (c) For vehicles of category N or M derived from N if the technically permissible maximum laden mass is 1 1 1 greater than 2,5 tons and the R-point height is greater than 850 mm from the ground and the power-to- mass ratio calculated by using the technically permissible maximum laden mass does not exceed 40. The sound emission of the vehicle under typical on-road driving conditions, which are different from those under which the type-approval test set out in Annex 3 and Annex 7 was carried out, shall not deviate from the test result in a significant manner. 6.2.3.1. The vehicle manufacturer shall not intentionally alter, adjust, or introduce any mechanical, electrical, thermal, or other device or procedure solely for the purpose of fulfilling the sound emission requirements as specified under this Regulation which is not operational during typical on-road operation. 6.2.3.2. The vehicle shall meet the requirements of Annex 7 to this Regulation. 6.2.3.3. In applying for type approval, the manufacturer shall provide a statement, in conformity with Appendix 1 of Annex 7, that the vehicle type to be approved complies with the requirements of paragraph 6.2.3 of this Regulation. 6.3. Specifications regarding exhaust systems containing fibrous materials 6.3.1. Requirements of Annex 4 shall be applied. 7. MODIFICATION AND EXTENSION OF APPROVAL OF A VEHICLE TYPE 7.1. Every modification of the vehicle type shall be notified to the Type Approval Authority which approved the vehicle type. The Type Approval Authority may then either: 7.1.1. Consider that the modifications made are unlikely to have an appreciable adverse effect and that in any case the vehicle still complies with the requirements, or 7.1.2. Require a further test report from the Technical Service responsible for conducting the tests. 7.2. Confirmation or refusal of approval, specifying the alterations shall be communicated by the procedure specified in paragraph 5.3 above to the Parties to the Agreement applying this Regulation. 7.3. The Type Approval Authority issuing the extension of approval shall assign a series number for such an extension and inform thereof the other Parties to the 1958 Agreement applying this Regulation by means of a communication form conforming to the model in Annex 1 to this Regulation. 8. CONFORMITY OF PRODUCTION 8.1 The conformity of production procedures shall comply with those set out in the Agreement, Appendix 2 (E/ECE/324-E/ECE/TRANS/505/Rev.2) with the following requirements: 8.1.1. Vehicles approved according to this Regulation shall be so manufactured as to conform to the type approved by meeting the requirements of paragraph 6 above. 8.1.2. The minimum requirements for conformity of production control procedures of Annex 6 to this Regulation shall be complied with.L 138/16 EN Official Journal of the European Union 4.6.2018 8.2. The authority which has granted type approval may at any time verify the conformity control methods applied in each production facility. The normal frequency of these verifications shall be one every two years. 9. PENALTIES FOR NON-CONFORMITY OF PRODUCTION 9.1. The approval granted in respect of a vehicle type pursuant to this Regulation may be withdrawn if the requirements set forth above are not met. 9.2. If a Contracting Party to the Agreement applying this Regulation withdraws an approval it has previously granted, it shall forthwith so notify the other Contracting Parties applying this Regulation, by means of a communication form conforming to the model in Annex 1 to this Regulation. 10. PRODUCTION DEFINITIVELY DISCONTINUED 10.1. If the holder of the approval completely ceases to manufacture a vehicle type approved in accordance with this Regulation, he shall so inform the authority which granted the approval. Upon receiving the relevant communication that authority shall inform thereof the other Parties to the 1958 Agreement applying this Regulation by means of a communication form conforming to the model in Annex 1 to this Regulation. 11. TRANSITIONAL PROVISIONS 11.1. As from the official date of entry into force of the 03 series of amendments to this Regulation, no Contracting Party applying this Regulation shall refuse to grant or refuse to accept type-approvals under this Regulation as amended by the 03 series of amendments. 11.2. Transitional Provisions for Phase 1 (see paragraph 6.2.2 above) 11.2.1. As from 1 July 2016, Contracting Parties applying this Regulation shall grant type-approvals only if the vehicle type to be approved meets the requirements of phase 1 (see paragraph 6.2.2 above) of this Regulation as amended by the 03 series of amendments. As from the official date of entry into force of the 03 series of amendments, Contracting Parties applying this Regulation shall grant type approvals to the vehicle type which meets the requirements of phase 2 or phase 3 of this Regulation as amended by the 03 series of amendments. 11.2.2. Contracting Parties applying this Regulation shall not refuse to grant extensions of type approvals for existing types which have been granted according to the 02 series of amendments to this Regulation. 11.2.3. Until 30 June 2022, no Contracting Party applying this Regulation shall refuse national or regional type approval of a vehicle type-approved to the 02 series of amendments to this Regulation. 11.2.4. As from 1 July 2022, Contracting Parties applying this Regulation shall not be obliged to accept for the purpose of national or regional type approval, a vehicle type approved to the preceding series of amendments to this Regulation. 11.2.5. Even after the date of entry into force of the 03 series of amendments to this Regulation, Contracting Parties applying this Regulation may continue for national or regional purposes granting type approvals and extensions of type approvals to the preceding series of amendments to this Regulation. 11.3. Transitional Provisions for Phase 2 (see paragraph 6.2.2 above) 11.3.1. As from 1 July 2020 for vehicle types other than N and as from 1 July 2022 for vehicle types of category 2 N , Contracting Parties applying this Regulation shall grant type approvals only if the vehicle type to be 2 approved meets the requirements of phase 2 (see paragraph 6.2.2 above) of this Regulation as amended by the 03 series of amendments. Furthermore, as from the official date of entry into force of the 03 series of amendments, Contracting Parties applying this Regulation shall grant type approvals to the vehicle type which meets the requirements of phase 3 of this Regulation as amended by the 03 series of amendments. 11.3.2. Contracting Parties applying this Regulation shall not refuse to grant extensions of type approvals for existing types which have been granted according to phase 1 (see paragraph 6.2.2 above) or the 02 series of amendments to this Regulation.4.6.2018 EN Official Journal of the European Union L 138/17 11.3.3. Until 30 June 2022 for vehicle types other than N and until 30 June 2023 for vehicle types of category N , 2 2 no Contracting Party applying this Regulation shall refuse national or regional type approval of a vehicle type-approved to phase 1 (see paragraph 6.2.2 above) or the 02 series of amendments to this Regulation. 11.3.4. As from 1 July 2022 for vehicle types other than N and as from 1 July 2023 for vehicle types of 2 category N , Contracting Parties applying this Regulation shall not be obliged to accept for the purpose of 2 national or regional type approval, a vehicle type approved to phase 1 (see paragraph 6.2.2.1 above) or the preceding series of amendments to this Regulation. 11.3.5. Even after the date of entry into force of the 03 series of amendments to this Regulation, Contracting Parties applying this Regulation may continue for national or regional purposes granting type approvals and extensions of type approvals to phase 1 (see paragraph 6.2.2 above) or the preceding series of amendments to this Regulation. 11.4. Transitional Provisions for Phase 3 (see paragraph 6.2.2 above) 11.4.1. As from 1 July 2024 for vehicle types other than N , N and M and as from 1 July 2026 for vehicle types of 2 3 3 category N , N and M , Contracting Parties applying this Regulation shall grant type-approvals only if the 2 3 3 vehicle type to be approved meets the requirements of phase 3 (see paragraph 6.2.2 above) of this Regulation as amended by the 03 series of amendments. 11.4.2. Contracting Parties applying this Regulation shall not refuse to grant extensions of type approvals for existing types which have been granted according to phase 2 according to paragraph 6.2.2 above. 11.4.3. Until 30 June 2026 for vehicle types other than N , N and M and until 30 June 2027 for vehicle types of 2 3 3 category N , N and M , no Contracting Party applying this Regulation shall refuse national or regional type 2 3 3 approval of a vehicle type-approved to phase 2 according to paragraph 6.2.2 above. 11.4.4. As from 1 July 2026 for vehicle types other than N , N and M and as from 1 July 2027 for vehicle types of 2 3 3 category N , N and M , Contracting Parties applying this Regulation shall not be obliged to accept for the 2 3 3 purpose of national or regional type approval, a vehicle type approved to phase 2 according to paragraph 6.2.2 above. 11.4.5. Even after the date of entry into force of the 03 series of amendments to this Regulation, Contracting Parties applying this Regulation may continue for national or regional purposes granting type approvals and extensions of type approvals to phase 1 or phase 2 (see paragraph 6.2.2 above) or the preceding series of amendments to this Regulation. 11.5. Notwithstanding the transitional provisions above, Contracting Parties whose application of this Regulation comes into force after the date of entry into force of the most recent series of amendments are not obliged to accept type approvals which were granted in accordance with any of the preceding series of amendments to this Regulation. 11.6. Until 30 June 2019, vehicles with a serial hybrid drive train which have a combustion engine with no mechanical coupling to the power train are excluded from the requirements of paragraph 6.2.3 above. 11.7. Until 30 June 2019, Contracting Parties applying this Regulation can continue to grant approvals using test sites which comply with the specifications of the preceding series of amendments to this Regulation as an alternative to Annex 3, paragraph 2.1 of this Regulation. 11.8. Until 30 June 2022 for vehicle types of category N or for vehicle types of category M derived from N the 1 1 1 limits according to paragraph 6.2.2 of the vehicle types of category N having a technically permissible 1 maximum laden mass above 2,5 tons apply, if all the following specifications are met: (a) Having a technically permissible maximum laden mass of less than or equal to 2,5 tons; (b) An R-point height greater or equal to 800 mm from the ground; (c) An engine capacity exceeding 660 cc but less than 1 495 cc; (d) An engine where the centre point of gravity of the engine is between 300 mm and 1 500 mm behind the front axle; (e) And having a rear axle drive.L 138/18 EN Official Journal of the European Union 4.6.2018 12. NAMES AND ADDRESSES OF TECHNICAL SERVICES RESPONSIBLE FOR CONDUCTING APPROVAL TESTS AND OF TYPE APPROVAL AUTHORITIES The Contracting Parties to the 1958 Agreement applying this Regulation shall communicate to the United Nations Secretariat the names and addresses of the Technical Services responsible for conducting approval tests and of the Type Approval Authorities which grant approval and to which forms certifying approval or extension or refusal or withdrawal of approval, issued in other countries, are to be sent.4.6.2018 EN Official Journal of the European Union L 138/19 ANNEX 1L 138/20 EN Official Journal of the European Union 4.6.20184.6.2018 EN Official Journal of the European Union L 138/21 Appendix 1 Addendum to the communication form No … 1. Additional information 1.1. Power plant 1.1.1. Manufacturer of the engine: ............................................................................................................................. 1.1.2. Manufacturer's engine code: ............................................................................................................................. 1.1.3. Rated maximum net power: ..... kW at ..... min– 1 or maximum continuous rated power (electric motor) ..... kW 1.1.4. Pressure charger(s), Make and Type: .................................................................................................................. 1.1.5. Air filter, Make and Type: ................................................................................................................................. 1.1.6. Intake silencer(s), Make and Type: ..................................................................................................................... 1.1.7. Exhaust Silencer(s), Make and Type: .................................................................................................................. 1.1.8. Catalyst(s), Make and Type: .............................................................................................................................. 1.1.9. Particulate Trap(s), Make and Type: ................................................................................................................... 1.2. Transmission 1.2.1. Type (mechanical, hydraulic, electric, etc.): ........................................................................................................ 1.3. Non-engine devices designed to reduce noise: ................................................................................................... 2. Test results 2.1. Sound level of moving vehicle: ................................................................................................................ dB(A) 2.2. Sound level of stationary vehicle: .............................................. dB(A) at ............................................... min– 1 2.2.1. Sound level of compressed air, service brake: ........................................................................................... dB(A) 2.2.2. Sound level of compressed air, parking brake: .......................................................................................... dB(A) 2.2.3. Sound level of compressed air, during the pressure regulator actuation: ..................................................... dB(A) 2.3. Data to facilitate in-use compliance test of hybrid vehicles, where an internal combustion engine cannot operate when the vehicle is stationary 2.3.1. Gear (i) or position of the gear selector chosen for the test: 2.3.2. Position of the operating switch during measurement Lwot (i), (if switch is fitted) 2.3.3. Pre-acceleration length l (Point of the acceleration depression in meter before line AA') PA 2.3.4. Sound pressure level L wot (i) ................................................................................................................. dB(A) 3. Remarks: ......................................................................................................................................................... ........................................................................................................................................................................L 138/22 EN Official Journal of the European Union 4.6.2018 Appendix 2 Technical Information Document 0. General 0.1. Make (trade name of manufacturer): ......................................................................................................... 0.2. Means of identification of type, if marked on the vehicle (1): ...................................................................... 0.2.1. Location of that marking: ........................................................................................................................ 0.3. Category of vehicle (2): ............................................................................................................................ 0.4. Company name and address of manufacturer: .......................................................................................... 0.5. Name and address of the manufacturer's representative (if any): ................................................................. 0.6. Name(s) and address(es) of assembly plant(s): ............................................................................................ 1. General construction characteristics of the vehicle 1.1. Photographs and/or drawings of a representative vehicle: .......................................................................... 1.2. Number of axles and wheels (3): ............................................................................................................... 1.2.1. Powered axles (number, position, interconnection): ................................................................................... 1.3. Position and arrangement of the engine: ................................................................................................... 2. Masses and dimensions (4) (in kg and mm) (Refer to drawing where applicable): ......................................... 2.1. Range of vehicle dimensions (overall): ...................................................................................................... 2.1.1. For chassis without bodywork: ................................................................................................................. 2.1.1.1. Length: ................................................................................................................................................... 2.1.1.2. Width: .................................................................................................................................................... 2.1.2. For chassis with bodywork ...................................................................................................................... 2.1.2.1. Length: ................................................................................................................................................... 2.1.2.2. Width: .................................................................................................................................................... 2.2. Mass in running order (5) (a) Minimum and maximum for each variant: .......................................................................................... (b) Mass of each version (a matrix shall be provided): ................................................................................ 2.3. Technically permissible maximum laden mass stated by the manufacturer (6) (7): 3. Power plant (8) 3.1. Manufacturer of the engine: ..................................................................................................................... 3.1.1. Manufacturer's engine code (as marked on the engine, or other means of identification): ............................ 3.2. Internal combustion engine 3.2.1. Specific engine information 3.2.1.1. Working principle: positive ignition/compression ignition, cycle four stroke/two stroke/rotary (9)4.6.2018 EN Official Journal of the European Union L 138/23 3.2.1.2. Number and arrangement of cylinders: ..................................................................................................... 3.2.1.2.1. Firing order: ........................................................................................................................................... 3.2.1.3. Engine capacity (10): ........................................................................................................................... cm3 3.2.1.4. Rated maximum net power: ........................ kW at ........................ min– 1 (manufacturer's declared value) 3.2.2. Fuel feed 3.2.2.1. By fuel injection (compression ignition only): yes/no (9) 3.2.2.1.1. Working principle: Direct injection/pre-chamber/swirl chamber (9) 3.2.2.1.2. Governor 3.2.2.1.2.1. Type: ...................................................................................................................................................... 3.2.2.1.2.2. Speed at which Cut-off starts under load: ........................................................................................ min– 1 3.2.2.2. By fuel injection (positive ignition only): yes/no (9) 3.2.2.2.1. Working principle: Intake manifold (single-/multi-point (2))/direct injection/other (specify) (9) 3.2.3. Intake system 3.2.3.1. Air filter, drawings, or 3.2.3.1.1. Make(s): .................................................................................................................................................. 3.2.3.1.2. Type(s): ................................................................................................................................................... 3.2.3.2. Intake silencer, drawings, 3.2.3.2.1. Make(s): .................................................................................................................................................. 3.2.3.2.2. Type(s): ................................................................................................................................................... 3.2.4. Exhaust system 3.2.4.1. Description and/or drawing of the exhaust system: ................................................................................... 3.2.4.2. Exhaust silencer(s): .................................................................................................................................. Type, marking of exhaust silencer(s): ......................................................................................................... Where relevant for exterior noise, reducing measures in the engine compartment and on the engine: .......... 3.2.4.3. Location of the exhaust outlet: ................................................................................................................. 3.2.4.4. Exhaust silencer containing fibrous materials: ........................................................................................... 3.2.5. Catalytic convertor: yes/no (9) 3.2.5.1. Number of catalytic convertors and elements (provide the information below for each separate unit): ......... 3.3. Electric motor 3.3.1. Type (winding, excitation): ....................................................................................................................... 3.3.1.1. Maximum hourly output: .................................................................................................................. kW 3.3.1.2. Operating voltage: ................................................................................................................................ V 3.4. Engine or motor combination: ................................................................................................................. 3.4.1. Hybrid electric vehicle: yes/no (9)L 138/24 EN Official Journal of the European Union 4.6.2018 3.4.2. Category of hybrid electric vehicle: off-vehicle charging/not off-vehicle charging (9): 3.4.3. Operating mode switch: with/without (9) 3.4.3.1. Selectable modes 3.4.3.1.1. Pure electric: yes/no (9) 3.4.3.1.2. Pure fuel consuming: yes/no (9) 3.4.3.1.3. Hybrid modes: yes/no (9) (if yes, short description): 3.4.4. Electric motor (describe each type of electric motor separately) 3.4.4.1. Make: ..................................................................................................................................................... 3.4.4.2. Type: ...................................................................................................................................................... 3.4.4.3. Rated maximum net power: .............................................................................................................. kW 4. Transmission (11) 4.1. Type (mechanical, hydraulic, electric, etc.): ................................................................................................ 4.2. Gear ratios Internal gearbox ratios Final drive ratio(s) Gear (ratios of engine to gearbox (ratio of gearbox output shaft Total gear ratios output shaft revolutions) to driven wheel revolutions) Maximum for CVT(1) 1 2 3 … Minimum for CVT Reverse (1) Continuous Variable Transmission (CVT): transmission with variable gear ratios. 4.3. Maximum vehicle design speed (in km/h) (12): ........................................................................................... 5. Suspension 5.1. Tyres and wheels 5.1.1. Tyre/wheel combination(s) (a) For tyres indicate size designation, load-capacity index and speed category symbol; (b) For wheels indicate rim size(s) and off-set(s). 5.1.2. Upper and lower limits of rolling radii 5.1.2.1. Axle 1: ................................................................................................................................................... 5.1.2.2. Axle 2: ................................................................................................................................................... 5.1.2.3. Axle 3: ................................................................................................................................................... 5.1.2.4. Axle 4: ................................................................................................................................................... etc.4.6.2018 EN Official Journal of the European Union L 138/25 6. Bodywork 6.1. Type of bodywork: .................................................................................................................................. 6.2. Materials used and methods of construction: ............................................................................................ 7. Miscellaneous 7.1. Details of any non-engine devices designed to reduce noise (if not covered by other items): ........................ Signed: ...................................................................................................................................................................... Position in company: ................................................................................................................................................. Date: ......................................................................................................................................................................... (1) If the means of identification of type contains characters not relevant to describe the vehicle types covered by the type-approval certificate such characters shall be represented in the documentation by the symbol: ‘?’ (e.g. ABC??123??). (2) As defined in the Consolidated Resolution on the Construction of Vehicles (R.E.3), document ECE/TRANS/WP.29/78/Rev.3, para. 2 — www.unece.org/trans/main/wp29/wp29wgs/wp29gen/wp29resolutions.html (3) Only for the purpose of defining ‘off-road vehicles’. (4) Standard ISO 612: 1978 — Road vehicles — Dimensions of motor vehicles and towed vehicles — terms and definitions. (a) Where there is one version with a normal cab and another with a sleeper cab, both sets of masses and dimensions are to be stated. (b) Optional equipment that affects the dimensions of the vehicle shall be specified. (5) The mass of the driver is assessed at 75 kg. The liquid containing systems (except those for used water that shall remain empty) are filled to 90 per cent of the capacity specified by the manufacturer. The information referred to in points 2.2(b) do not need to be provided for vehicle categories N, N, M and M. 2 3 2 3 (6) For vehicles coupled with a trailer or a semi-trailer, which exert a significant vertical load on the coupling device or the fifth wheel, this load, divided by standard acceleration of gravity, is included in the maximum technically permissible mass. Please fill in here the upper and lower values for each variant. (7) Please fill in here the upper and lower values for each variant. (8) In the case of a vehicle that can run either on petrol, diesel, etc., or also in combination with another fuel, items shall be repeated. In the case of non-conventional engines and systems, particulars equivalent to those referred here shall be supplied by the manufacturer. (9) Delete what does not apply. (10) This value shall be calculated (π = 3,1416) and rounded off to the nearest cm3. (11) The specified particulars are to be given for any proposed variants. (12) With respect to trailers, maximum speed permitted by the manufacturer.L 138/26 EN Official Journal of the European Union 4.6.2018 ANNEX 2 ARRANGEMENTS OF THE APPROVAL MARK Model A (See paragraph 5.4 of this Regulation) a = 8 mm min. The above approval mark affixed to a vehicle shows that the vehicle type concerned has, with regard to its noise emission, been approved in the Netherlands (E 4) pursuant to Regulation No 51 under approval No 032439. The first two digits of the approval number indicate that Regulation No 51 already included the 03 series of amendments when the approval was granted. Model B (See paragraph 5.5 of this Regulation) a = 8 mm min. The above approval mark affixed to a vehicle shows that the vehicle type concerned has been approved in the Netherlands (E 4) pursuant to Regulations Nos 51 and 33 (1). The approval numbers indicate that, at the dates when the respective approvals were granted, Regulation No 51 included the 03 series of amendments while Regulation No 33 was in its original form. (1) The latter number is given as an example only.4.6.2018 EN Official Journal of the European Union L 138/27 ANNEX 3 METHODS AND INSTRUMENTS FOR MEASURING THE SOUND MADE BY MOTOR VEHICLES 1. Measuring instruments 1.1. Acoustic measurements The apparatus used for measuring the sound level shall be a precision sound-level meter or equivalent measurement system meeting the requirements of Class 1 instruments (inclusive of the recommended windscreen, if used). These requirements are described in ‘IEC 61672-1:2002: Precision sound level meters’, second edition, of the International Electrotechnical Commission (IEC). Measurements shall be carried out using the ‘fast’ response of the acoustic measurement instrument and the ‘A’ weighting curve also described in ‘IEC 61672-1:2002’. When using a system that includes a periodic monitoring of the A-weighted sound pressure level, a reading should be made at a time interval not greater than 30 ms. The instruments shall be maintained and calibrated in accordance to the instructions of the instrument manufacturer. 1.2. Calibration of the entire Acoustic Measurement System for a Measurement Session At the beginning and at the end of every measurement session the entire measurement system shall be checked by means of a sound calibrator that fulfils the requirements for sound calibrators of at least precision Class 1 according to IEC 60942:2003. Without any further adjustment the difference between the readings of two consecutive checks shall be less than or equal to 0,5 dB(A). If this value is exceeded, the results of the measurements obtained after the previous satisfactory check shall be discarded. 1.3. Compliance with requirements Compliance of the acoustic measurement instrumentation shall be verified by the existence of a valid certificate of compliance. These certificates shall be deemed to be valid if certification of compliance with the standards was conducted within the previous 12 month period for the sound calibration device and within the previous 24 month period for the instrumentation system. All compliance testing shall be conducted by a laboratory, which is authorised to perform calibrations traceable to the appropriate standards. 1.4. Instrumentation for speed measurements The engine speed shall be measured with instrumentation having an accuracy of ± 2 per cent or better at the engine speeds required for the measurements being performed. The road speed of the vehicle shall be measured with instrumentation having an accuracy of at least ± 0,5 km/h, when using continuous measurement devices. If testing uses independent measurements of speed, this instrumentation shall meet specification limits of at least ± 0,2 km/h. 1.5. Meteorological instrumentation The meteorological instrumentation used to monitor the environmental conditions during the test shall include the following devices, which meet at least the given accuracy: (a) Temperature measuring device, ± 1 °C; (b) Wind speed-measuring device, ± 1,0 m/s; (c) Barometric pressure measuring device, ± 5 hPa; (d) A relative humidity measuring device, ± 5 per cent.L 138/28 EN Official Journal of the European Union 4.6.2018 2. Conditions of measurement 2.1. Test Site and ambient conditions The surface of the test track and the dimensions of the test site shall be in accordance with ISO 10844:2014. The surface of the site shall be free of powdery snow, tall grass, loose soil or cinders. There shall be no obstacle which could affect the sound field within the vicinity of the microphone and the sound source. The observer carrying out the measurements shall so position themself as not to affect the readings of the measuring instrument. Measurements shall not be made under adverse weather conditions. It shall be ensured that the results are not affected by gusts of wind. The meteorological instrumentation should be positioned adjacent to the test area at a height of 1,2 m ± 0,02 m. The measurements shall be made when the ambient air temperature is within the range from 5 °C to 40 °C. The tests shall not be carried out if the wind speed, including gusts, at microphone height exceeds 5 m/s, during the sound measurement interval. A value representative of temperature, wind speed and direction, relative humidity, and barometric pressure shall be recorded during the sound measurement interval. Any sound peak which appears to be unrelated to the characteristics of the general sound level of the vehicle shall be ignored in taking the readings. The background noise shall be measured for duration of 10 seconds immediately before and after a series of vehicle tests. The measurements shall be made with the same microphones and microphone locations used during the test. The A-weighted maximum sound pressure level shall be reported. The background noise (including any wind noise) shall be at least 10 dB(A) below the A-weighted sound pressure level produced by the vehicle under test. If the difference between the ambient noise and the measured sound is between 10 and 15 dB(A), in order to calculate the test results the appropriate correction shall be subtracted from the readings on the sound-level meter, as in the following table: Difference between ambient noise and sound to be 10 11 12 13 14 15 measured dB(A) Correction dB(A) 0,5 0,4 0,3 0,2 0,1 0,0 2.2. Vehicle 2.2.1. The vehicle shall be representative of vehicles to be put on the market as specified by the manufacturer in agreement with the Technical Service to fulfil the requirements of this Regulation. Measurements shall be made without any trailer, except in the case of non-separable vehicles. At the request of the manufacturer, measurements may be made on vehicles with lift axle(s) in a raised position. Measurements shall be made on vehicles at the test mass m specified according to the following table. t Target mass, m , is used to denote the mass that N and N vehicles should be tested at. The actual test target 2 3 mass of the vehicle can be less due to limitations on vehicle and axle loading. Vehicle category Vehicle test mass M m = m +/– 5 % 1 t ro N m = m +/– 5 % 1 t ro4.6.2018 EN Official Journal of the European Union L 138/29 Vehicle category Vehicle test mass N , N m = 50 [kg/kW] × P [kW] 2 3 target n Extra loading, m , to reach the target mass, m , of the vehicle shall be placed xload target above the rear axle(s). The sum of the extra loading and the rear axle load in an unladen condition, m , is limited to 75 per cent of the technically permissible maximum laden ra load unladen mass allowed for the rear axle, m . The target mass shall be achieved with a toler­ ac ra max ance of ± 5 per cent. If the centre of gravity of the extra loading cannot be aligned with the centre of the rear axle, the test mass, m, of the vehicle shall not exceed the sum of the front axle in t an unladen condition, m , and the rear axle load in an unladen condition, fa load unladen m plus the extra loading, m and the mass of the driver m. ra load unladen xload, d The test mass for vehicles with more than two axles shall be the same as for a two- axle vehicle. If the vehicle mass of a vehicle with more than two axles in an unladen condition, m , is greater than the test mass for the two-axle vehicle, then this vehicle shall be unladen tested without extra loading. If the vehicle mass of a vehicle with two axles, m , is greater than the target mass, unladen then this vehicle shall be tested without extra loading. M , M m = m 2 3 t ro The mass in running order shall be achieved with a tolerance of ± 10 %. Incomplete If the tests are carried with an incomplete vehicle not having a bodywork, M , M m = 50 [kg/kW] × P [kW] is calculated in compliance with conditions above (see 2 3 target n N , N category), 2 3 or m = m + m = m t chassisM2M3 xloadM2M3 ro The mass in running order shall be achieved with a tolerance of ± 10 %. 2.2.2. At the applicant's request the vehicle of a category M , M , N or N is deemed representative of its 2 3 2 3 completed type if the tests are carried out to an incomplete vehicle not having a bodywork. In the test of an incomplete vehicle all relevant soundproofing materials, panels and noise reduction components and systems shall be fitted on the vehicle as designed by the manufacturer except a part of bodywork which is built in a later stage. No new test shall be required due to fitting of a supplement fuel tank or re-location of the original fuel tank on condition that other parts or structures of the vehicle apparently affecting sound emissions have not been altered. The tyres to be used for the test shall be representative for the vehicle and shall be selected by the vehicle manufacturer and recorded in Addendum to the Communication form (Annex 1, Appendix 1). They shall correspond to one of the tyre sizes designated for the vehicle as original equipment. The tyre is or will be commercially available on the market at the same time as the vehicle (1) .The tyres shall be inflated to the pressure recommended by the vehicle manufacturer for the test mass of the vehicle. The tyres shall have at least 1,6 mm tread depth. 2.2.3. Before the measurements are started, the engine shall be brought to its normal operating conditions. 2.2.4. If the vehicle is fitted with more than two-wheel drive, it shall be tested in the drive which is intended for normal road use. 2.2.5. If the vehicle is fitted with fan(s) having an automatic actuating mechanism, this system shall not be interfered with during the measurements. (1) Given that the tyre contribution for overall sound emission is significant, regard shall be given for existing regulatory provisions concerning tyre/road sound emissions. Traction tyres, snow tyres and special-use tyres as defined in paragraph 2 of Regulation No 117 shall be excluded during type-approval and conformity of production measurements at the request of the manufacturer in accordance with Regulation No 117.L 138/30 EN Official Journal of the European Union 4.6.2018 2.2.6. If the vehicle is equipped with an exhaust system containing fibrous materials, the exhaust system is to be conditioned before the test according to Annex 4. 2.2.7. Calculation procedure to determine extra loading of N and N vehicles only 2 3 2.2.7.1. Calculation of extra loading The target mass, m , (per kW rated power) for two-axle vehicles of category N and N is specified in the target 2 3 Table in paragraph 2.2.1 above. m = 50 [kg/kW] × P [kW] (1) target n To reach the required target mass, m , for a vehicle being tested, the unladen vehicle, including the mass target of the driver, m, shall be loaded with an extra mass, m , which shall be placed above the rear axle as d xload given in Formula (8): m = m + m + m (2) target unladen d xload The target mass, m , shall be achieved with a tolerance of ± 5 per cent. target The vehicle mass of the test vehicle in the unladen condition, m , is calculated by measuring on a scale unladen the unladen front axle load, m , and the unladen rear axle load, m , as given in fa load unladen ra load unladen Formula (3): m = m + m (3) unladen fa load unladen ra load unladen By using Formulae (2) and (3), the extra loading, m , is calculated as given in Formulae (4) and (5): xload m = m – (m + m ) (4) xload target d unladen m = m – (m + m + m ) (5) xload target d fa load unladen ra load unladen The sum of the extra loading, m , and the unladen rear axle load, m , is limited to 75 per cent of xload ra load unladen the technically permissible maximum laden mass for the rear axle, m , as given in Formula (6): ac ra max 0,75 m ≥ m + m (6) ac ra max xload ra load unladen The m is limited according to Formula (7): xload m ≤ 0,75 m – m (7) xload ac ra max ra load unladen If the calculated extra loading, m , in Formula (5) fulfils Formula (7), then the extra loading is equal to xload Formula (5). The test mass, m, of the vehicle is as calculated from Formula (8): t m = m + m + m + m (8) t xload d fa load unladen ra load unladen In this case, the test mass of the vehicle is equal to the target mass m = m (9) t target If the calculated extra loading, m , in Formula (5) does not fulfil Formula (7), but rather fulfils xload Formula (10) m > 0,75 m – m (10) xload ac ra max ra load unladen then, the extra loading, m , shall be as given by Formula (11): xload m = 0,75 m – m (11) xload ac ra max ra load unladen and the test mass, m, of the vehicle shall be as given by Formula (12): t m = 0,75 m + m + m (12) t ac ra max d fa load unladen In this case, the test mass of the vehicle is lower than the target mass m < m (13) t target4.6.2018 EN Official Journal of the European Union L 138/31 2.2.7.2. Loading considerations if load cannot be aligned with the centre of rear axle If the centre of gravity of the extra loading, m , cannot be aligned with the centre of the rear axle, the xload test mass of the vehicle, m, shall not exceed the sum of the unladen front axle load, m , and the t fa load unladen unladen rear axle load, m , plus the extra loading, m , and the mass of the driver, m. ra load unladen xload d This means that if the actual front and rear axle loads are measured on a scale when the extra loading, m , is placed onto the vehicle and it is aligned with the centre of the rear axle, the test mass of the xload vehicle minus the mass of the driver is as given by Formula (14): m – m = m + m (14) t d fa load laden ra load laden Where: m = m (15) fa load laden fa load unladen If the centre of gravity of the extra loading cannot be aligned with the centre of the rear axle, Formula (14) is still fulfilled, but m > m (16) fa load laden fa load unladen because the extra loading has partly distributed its mass to the front axle. In that case, it is not allowed to add more mass onto the rear axle to compensate for the mass moved to the front axle. 2.2.7.3. Test mass for vehicles with more than two axles If a vehicle with more than two axles is tested, then the test mass of this vehicle shall be the same as the test mass for the two-axle vehicle. If the unladen vehicle mass of a vehicle with more than two axles is greater than the test mass for the two- axle vehicle, then this vehicle shall be tested without extra loading. 3. Methods of testing 3.1. Measurement of sound of vehicles in motion 3.1.1. General conditions of test Two lines, AA′ and BB′, parallel to line PP′ and situated respectively 10 m ± 0,05 m forward and 10 m ± 0,05 m rearward of line PP′ shall be marked out on the test runway. At least four measurements shall be made on each side of the vehicle and for each gear. Preliminary measurements may be made for adjustment purposes, but shall be disregarded. The microphone shall be located at a distance of 7,5 m ± 0,05 m from the reference line CC′ of the track and 1,2 m ± 0,02 m above the ground. The reference axis for free field conditions (see IEC 61672-1:2002) shall be horizontal and directed perpen­ dicularly towards the path of the vehicle line CC′. 3.1.2. Specific test conditions for vehicles 3.1.2.1. Vehicles of category M , N and M ≤ 3 500 kg technically permissible maximum laden mass: 1 1 2 The path of the centreline of the vehicle shall follow line CC′ as closely as possible throughout the entire test, from the approach to line AA′ until the rear of the vehicle passes line BB′. If the vehicle is fitted with more than two-wheel drive, test it in the drive selection which is intended for normal road use. If the vehicle is fitted with an auxiliary manual transmission or a multi-gear axle, the position used for normal urban driving shall be used. In all cases, the gear ratios for slow movements, parking or braking shall be excluded.L 138/32 EN Official Journal of the European Union 4.6.2018 The test mass of the vehicle shall be according to the table of paragraph 2.2.1. The test speed v is 50 km/h ± 1 km/h. The test speed shall be reached, when the reference point is at test line PP′. If the test speed is modified according to paragraph 3.1.2.1.4.1(e) of Annex 3 to this Regulation, the modified test speed shall be used for both the acceleration and constant speed test. 3.1.2.1.1. Power to mass ratio index (PMR) PMR is defined as follows: PMR = (P /m ) * 1 000 kg/kW, where P is measured in kW and m is measured in kg according to n ro n ro paragraph 2.2.1 of this Annex. If two or more sources of propulsive power operate at the conditions of test specified in paragraph 3.1.2.1 of Annex 3 to this Regulation, the total engine net power, P , shall be the arithmetic sum of parallel n propulsive engines on the vehicle. Applicable parallel propulsive engines are those power sources which provide forward motion to the vehicle in combination at the conditions of test specified in paragraph 3.1.2.1 of Annex 3 to this Regulation. Specified power for non-combustion engines shall be the power stated by the manufacturer. The PMR with no dimension is used for the calculation of acceleration. 3.1.2.1.2. Calculation of acceleration Acceleration calculations are applicable to M , N and M ≤ 3 500 kg technically permissible maximum 1 1 2 laden mass categories only. All accelerations are calculated using different speeds of the vehicle on the test track (1). The formulae given are used for the calculation of a , a and a . The speed either at AA′ or PP′ is defined as the wot i wot i + 1 wot test vehicle speed when the reference point passes AA′ (v ) or PP′ (v ). The speed at BB′ is defined when the AA′ PP′ rear of the vehicle passes BB′ (v ). The method used for determination of the acceleration shall be BB′ indicated in the test report. Due to the definition of the reference point for the vehicle the length of the vehicle (l ) is considered veh differently in the formula below. If the reference point is in the front of the vehicle, then l = l , mid: veh l = ½ l and rear: l = 0. veh At the choice of the vehicle manufacturer, front engine vehicles may use l = 5 m, and mid-engine vehicles may use l = 2,5 m. 3.1.2.1.2.1. Calculation procedure for vehicles with manual transmission, automatic transmission, adaptive transmissions and transmissions with continuous variable transmissions (CVTs) tested with locked gear ratios: a = ((v /3,6)2 – (v /3,6)2)/(2*(20 + l)) wot test BB′ AA′ a used in the determination of gear selection shall be the average of the four a during each valid wot test wot test, i measurement run. Pre-acceleration may be used. The point of depressing the accelerator before line AA′ shall be reported in the Addendum to the Communication form (Annex 1, Appendix 1). 3.1.2.1.2.2. Calculation procedure for vehicles with automatic transmissions, adaptive transmissions and CVTs tested with non-locked gear ratios: a used in the determination of gear selection shall be the average of the four a during each valid wot test wot test, i measurement run. (1) See Annex 3, Appendix, Figure 1.4.6.2018 EN Official Journal of the European Union L 138/33 If devices or measures described in paragraph 3.1.2.1.4.2 can be used to control transmission operation for the purpose of achieving test requirements, calculate a using the equation: wot test a = ((v /3,6)2 – (v /3,6)2)/(2*(20 + l)) wot test BB′ AA′ Pre-acceleration may be used. If devices or measures described in paragraph 3.1.2.1.4.2 are not used, calculate a test using the equation: wot a = ((v /3,6)2 – (v /3,6)2)/(2*(10 + l)) wot_testPP-BB BB′ PP′ Pre-acceleration shall not be used. The location of depressing the accelerator shall be where the reference point of the vehicle passes line AA′. 3.1.2.1.2.3. Target acceleration The target acceleration a defines the typical acceleration in urban traffic and is derived from statistical urban investigations. This function depends on the PMR of a vehicle. The target acceleration a is defined by: urban a = 0,63 * log (PMR) – 0,09 urban 10 3.1.2.1.2.4. Reference acceleration The reference acceleration a defines the required acceleration during the acceleration test on the test wot ref track. It is a function depending on the power-to-mass ratio of a vehicle. That function is different for specific vehicle categories. The reference acceleration a ref is defined by: wot a = 1,59 * log (PMR) – 1,41 for PMR ≥ 25 wot ref 10 a = a = 0,63 * log (PMR) – 0,09 for PMR < 25 wot ref urban 10 3.1.2.1.3. Partial power factor k P The partial power factor k (see paragraph 3.1.3.1) is used for the weighted combination of the test results P of the acceleration test and the constant speed test for vehicles of category M and N and M ≤ 3 500 kg 1 1 2 technically permissible maximum laden mass In cases other than a single gear test, a shall be used instead of a (see paragraph 3.1.3.1). wot ref wot test 3.1.2.1.4. Gear ratio selection The selection of gear ratios for the test depends on their specific acceleration potential a under full wot throttle condition, according to the reference acceleration a required for the full throttle acceleration wot ref test. If the vehicle allows different transmission setups like automatic or manual gear selection and/or has different software programs or modes (e.g. sporty, winter, adaptive) leading to valid accelerations, the vehicle manufacturer shall prove to the satisfaction of the Technical Service, that the vehicle is tested in the mode which achieves an acceleration being closest to a . wot ref The vehicle transmission, gear, or gear ratio may be controlled by electronic or mechanical measures to avoid the activation of a ‘kick-down function’. Appendix to this Annex, Figure 3a to Figure 3e, give gear selection criteria and test run criteria for categories M and M having a technically permissible maximum laden mass not exceeding 3 500 kg and 1 2 for category N , in a flowchart form as an aid to test operation. 1L 138/34 EN Official Journal of the European Union 4.6.2018 3.1.2.1.4.1. Vehicles with manual transmission, automatic transmissions, adaptive transmissions or CVTs tested with locked gear ratios The following conditions for selection of gear ratios are possible: (a) If one specific gear ratio gives an acceleration in a tolerance band of ± 5 per cent of the reference acceleration a , not exceeding 2,0 m/s2, test with that gear ratio. wot ref (b) If none of the gear ratios give the required acceleration, then choose a gear ratio i, with an acceleration higher and a gear ratio i + 1, with an acceleration lower than the reference acceleration. If the acceleration value in gear ratio i does not exceed 2,0 m/s2, use both gear ratios for the test. The weighting ratio in relation to the reference acceleration a is calculated by: wot ref k = (a – a )/(a – a ) wot ref wot (i + 1) wot (i) wot (i + 1) (c) If the acceleration value of gear ratio i exceeds 2,0 m/s2, the first gear ratio shall be used that gives an acceleration below 2,0 m/s2 unless gear ratio i + 1 provides acceleration less than a . In this case, two urban gears, i and i + 1 shall be used, including the gear i with acceleration exceeding 2,0 m/s2. In other cases, no other gear shall be used. The achieved acceleration a during the test shall be used for the wot test calculation of the part power factor k instead of a . P wot ref (d) If the vehicle has a transmission in which there is only one selection for the gear ratio the acceleration test is carried out in this vehicle gear selection. The achieved acceleration is then used for the calculation of the part power factor k instead of a . P wot ref (e) If rated engine speed is exceeded in a gear ratio before the vehicle passes BB′ the next higher gear shall be used. If the next higher gear results in an acceleration below a , the vehicle test speed, v , shall be urban test reduced by 2,5 km/h and the gear ratio selection shall proceed as specified by the options given in this paragraph. In no case shall the vehicle test speed be reduced below 40 km/h. In this case, a gear ratio is allowed even if a test does not exceed a . wot urban In the case of a vehicle not exempted from ASEP according to paragraph 6.2.3, gear i shall be tested and values reported (L n v ) in order to perform tests of Annex 7. wot i, wot,BB i wot,BB i 3.1.2.1.4.2. Vehicles with automatic transmission, adaptive transmissions and CVTs tested with non-locked gear ratios: The gear selector position for full automatic operation shall be used. The acceleration value a test shall be calculated as defined in paragraph 3.1.2.1.2.2. wot The test may then include a gear change to a lower range and a higher acceleration. A gear change to a higher range and a lower acceleration is not allowed. A gear shifting to a gear ratio which is not used in urban traffic shall be avoided. Therefore, it is permitted to establish and use electronic or mechanical devices, including alternate gear selector positions, to prevent a downshift to a gear ratio which is typically not used for the specified test condition in urban traffic. The achieved acceleration a shall be greater or equal to a . wot test urban If possible, the manufacturer shall take measures to avoid an acceleration value a greater than 2,0 m/s2. wot test The achieved acceleration a is then used for the calculation of the partial power factor k (see wot test p paragraph 3.1.2.1.3) instead a . wot ref 3.1.2.1.5. Acceleration test The manufacturer shall define the position of the reference point in front of line AA′ of fully depressing the accelerator. The accelerator shall be fully depressed (as rapidly as is practicable) when the reference point of the vehicle reaches the defined point. The accelerator shall be kept in this depressed condition until the rear4.6.2018 EN Official Journal of the European Union L 138/35 of the vehicle reaches line BB′. The accelerator shall then be released as rapidly as possible. The point of fully depressing the accelerator shall be reported in Addendum to the Communication form (Annex 1, Appendix 1). The Technical Service shall have the possibility of pretesting. In the case of articulated vehicles consisting of two non-separable units regarded as a single vehicle, the semi-trailer shall be disregarded in determining when line BB′ is crossed. 3.1.2.1.6. Constant speed test The constant speed test shall be carried out with the same gear(s) specified for the acceleration test and a constant speed of 50 km/h with a tolerance of ±1 km/h between AA′ and BB′. During the constant speed test the acceleration control shall be positioned to maintain a constant speed between AA′ and BB′ as specified. If the gear is locked for the acceleration test, the same gear shall be locked for the constant speed test. The constant speed test is not required for vehicles with a PMR < 25. 3.1.2.2. Vehicles of categories M > 3 500 kg technically permissible maximum laden mass, M , N , N : 2 3 2 3 The path of the centreline of the vehicle shall follow line CC′ as closely as possible throughout the entire test, from the approach to line AA′ until the rear of the vehicle passes line BB′. The test shall be conducted without a trailer or semi-trailer. If a trailer is not readily separable from the towing vehicle the trailer shall be ignored when considering the crossing of line BB′. If the vehicle incorporates equipment such as a concrete mixer, a compressor, etc., this equipment shall not be in operation during the test. The test mass of the vehicle shall be according to the table of paragraph 2.2.1 of Annex 3 to this Regulation. The value of n and v used in the determination of gear and vehicle speed selection shall be the average BB′ BB′ of the four n , j and v , j values during each valid measurement run. BB′ BB′ The value of n shall be reported to a precision of 10 revolutions per minute. The reported n shall be BB′ BB′ used in all subsequent calculation. The value of v shall be reported to the first digit after the decimal (xx,x). The reported v shall be used BB′ BB′ in all subsequent calculation. Target conditions of category M > 3 500 kg technically permissible maximum laden mass, N : 2 2 When the reference point passes line BB′, the engine speed n shall be between 70 and 74 per cent of BB′ speed S, at which the engine develops its rated maximum net power, and the vehicle speed shall be 35 km/h ± 5 km/h. Between line AA′ and line BB′ a stable acceleration condition shall be ensured. Target conditions of category M , N : 3 3 When the reference point passes line BB′, the engine speed n shall be between 85 and 89 per cent of BB′ speed S, at which the engine develops its rated maximum net power, and the vehicle speed shall be 35 km/h ± 5 km/h. Between line AA′ and line BB′ a stable acceleration condition shall be ensured. 3.1.2.2.1. Gear ratio selection It is the responsibility of the manufacturer to determine the correct manner of testing to achieve the required conditions. The vehicle transmission, gear, or gear ratio, shall be chosen to be able to fulfil the target conditions according to paragraphs 3.1.2.2.1.1 or 3.1.2.2.1.2 of Annex 3 to this Regulation. The vehicle transmission, gear, or gear ratio may be controlled by electronic or mechanical measures including exclusion of kick- down function.L 138/36 EN Official Journal of the European Union 4.6.2018 Appendix to this Annex, Figure 4a to Figure 4d, give gear selection criteria and test run criteria for categories M having a technically permissible maximum laden mass exceeding 3 500 kg, and for 2 category N , M and N , in a flowchart as an aid to test operation. 2 3 3 3.1.2.2.1.1. Manual transmission, automatic transmissions, adaptive transmissions or transmissions with continuously variable gear ratios (CVTs) tested with locked gear ratios Stable acceleration condition shall be ensured. The gear choice is determined by the target conditions. The following conditions for fulfilling the target conditions in paragraph 3.1.2.2 of Annex 3 to this Regulation are possible: (a) If one gear choice fulfils both target conditions for the rotational engine speed n and for the target BB′ vehicle speed v , test with that gear. target BB′ (b) If more than one gear choice fulfils both target conditions for the rotational engine speed n and target BB′ for the vehicle speed v , test in gear i that gives velocity v closest to 35 km/h. target BB′ BB′ gear i (c) If two gear choices fulfil both target conditions for the rotational engine speed n and for the target BB′ vehicle speed v , and fulfil the following condition. target BB′ (v – v ) = (v – v ) target BB′ BB′ gear i BB′ gear i + 1 target BB′ then both gears are taken for further calculation of L . urban (d) If one gear choice fulfils the target condition for the rotational engine speed n but not the target target BB′ condition for the vehicle speed v , use two gears, gear and gear. The target conditions for the target BB′ x y vehicle speed for these two gears are as follows: gear x 25 km/h ≤ v ≤ 30 km/h BB′x and gear y 40 km/h ≤ v ≤ 45 km/h BB′y Both gears, gear and gear shall fulfil the target rotational engine speed n . Both gears shall be x y target BB′ used for further calculation of L . urban If only one of the gears fulfils the target rotational engine speed, n , test with that gear. This gear target BB′ shall be used for further calculation of L . urban (e) If none of the two gears fulfils the target rotational engine speed n under condition (d) then target BB′ condition (f) shall be chosen. (f) If no gear choice fulfils the target rotational engine speed choose the gear that fulfils the target vehicle velocity v and is closest to the target rotational engine speed n , but not higher than n . target BB′ target BB′ target BB′ v = v BB′ gear i target BB′ n ≤ n BB′ gear i target BB′ A stable acceleration condition shall be insured. If a stable acceleration cannot be insured in a gear, this gear shall be disregarded. In all conditions, the rated engine speed shall not be exceeded while the reference point of the vehicle is in the measurement zone. If the rated engine speed is exceeded within the measurement zone, this gear shall be disregarded. 3.1.2.2.1.2. Automatic transmission, adaptive transmissions, and transmissions with variable gear ratio tested with non- locked gear ratios The gear selector position for full automatic operation shall be used. The test may then include a gear change to a lower range and a higher acceleration. A gear change to a higher range and a lower acceleration is not allowed. In any case a gear change to a gear ratio that is typically not used at the specified condition as defined by the manufacturer in urban traffic shall be avoided.4.6.2018 EN Official Journal of the European Union L 138/37 Therefore, it is permitted to establish and use electronic or mechanical devices, including alternative gear selector positions, to prevent a downshift to a gear ratio that is typically not used at the specified test condition as defined by the manufacturer in urban traffic. The following conditions for fulfilling the target conditions in paragraph 3.1.2.2 of Annex 3 to this Regulation are possible: (a) If the choice of the gear selector position fulfils both target conditions for the rotational engine speed n and for the vehicle speed v , test with the gear selector in that position. target BB′ target BB′ (b) If the choice of the gear selector position fulfils the target condition for the rotational engine speed n but not the target condition for the vehicle speed v , change the target condition for target BB′ target BB′ the vehicle speed to two vehicle target speeds as follows: Define v as BB′1 25 km/h ≤ v ≤ 35 km/h BB′1 and Define v as BB′2 35 km/h ≤ v ≤ 45 km/h. BB′2 Conduct two tests, one with v and one with v . BB′1 BB′2 Both test conditions are used for further calculation of L . urban (c) If under condition (b) the target rotational engine speed n cannot be fulfilled, condition (d) shall target BB′ be chosen. (d) If the choice of the gear selector position cannot fulfil the target condition for the rotational engine speed n but the target condition for the vehicle speed v , change the target condition for the target BB′ target BB′ vehicle speed to two vehicle target speeds as follows: Define v as BB′1 25 km/h ≤ v ≤ 30 km/h BB′1 and Define v as BB′2 40 km/h ≤ v ≤ 45 km/h. BB′2 Conduct two tests, one with v and one with v . BB′1 BB′2 Use the test where n is closest to the target rotational engine speed n but not higher than BB′ target BB′ n . target BB′ n ≤ n for i = 1, 2 BB′ i target BB′ If the vehicle cannot fulfil the condition: n ≤ n for i = 1, 2 BB′ i target BB′ condition (e) shall be used. (e) If the choice of the gear selector position cannot fulfil the target conditions for the rotational engine speed n and the target condition for the vehicle speed v , change the target condition for the target BB′ target BB′ vehicle speed to the following: v = v + 5 km/h BB′ target BB′ Conduct the test with that vehicle speed v where n is closest to the target rotational engine BB′ BB′ speed n . A gear change to a higher range and a lower acceleration is allowed after the vehicle target BB′ passes line PP′. (f) If the vehicle includes a transmission design that provides only a single gear selection (D) that limits engine speed during the test, the vehicle shall be tested using only the target vehicle speed v . target BB′L 138/38 EN Official Journal of the European Union 4.6.2018 3.1.2.2.1.3. Powertrain with no combustion engine rotational engine speed available Vehicles with a powertrain where no combustion engine rotational engine speed is available shall fulfil only the target condition for the vehicle speed v target BB′ The following conditions for fulfilling the target condition v in paragraph 3.1.2.2 of Annex 3 to this target BB′ Regulation are possible. (a) If no rotational engine speed is available, it is necessary to fulfil only the target vehicle speed v . target BB′ (b) If no rotational engine speed is available and the target vehicle speed v cannot be fulfilled, two target BB′ test conditions shall be conducted as follows: v for the first test condition is defined as BB′1 25 km/h ≤ v ≤ 35 km/h BB′1 and v for the second test condition is defined as BB′2 35 km/h ≤ v ≤ 45 km/h BB′2 Both test conditions are used for further calculation of L . urban (c) If no rotational engine speed is available and the target vehicle speed v and v defined as target BB′ BB′1 25 km/h ≤ v ≤ 35 km/h BB′1 cannot be fulfilled, it is necessary to conduct, only one test with v where v is defined as BB′2 BB′2 35 km/h ≤ v ≤ 45 km/h BB′2 The test condition for v is taken for further calculation of L . BB′2 urban 3.1.2.2.2. Acceleration test When the reference point of the vehicle reaches the line AA′ the accelerator control shall be fully depressed (without operating the automatic downshift to a lower range than normally used in urban driving) and held fully engaged until the reference point reaches BB′ + 5 m. The acceleration control unit can then be released on request of the manufacturer. In the case of articulated vehicles consisting of two non-separable units regarded as a single vehicle, the semi-trailer shall be disregarded in determining when line BB′ is crossed. 3.1.3. Interpretation of results For vehicles of categories M and M having a maximum authorised mass not exceeding 3 500 kg, and 1 2 category N the maximum A-weighted sound pressure level indicated during each passage of the vehicle 1 between the two lines AA′ and BB′ shall be rounded to the first significant digit after the decimal place (e.g. XX,X). For vehicles of category M having a maximum authorised mass exceeding 3 500 kg and categories M , N , 2 3 2 and N the maximum A-weighted sound pressure level indicated during each passage of the reference point 3 of the vehicle between line AA′ and line BB′ + 5 m shall be rounded, to the first significant digit after the decimal place (e.g. XX,X). If a sound peak obviously out of character with the general sound pressure level is observed, the measurement shall be discarded. At least four measurements for each test condition shall be made on each side of the vehicle and for each gear ratio. Left and right sides may be measured simultaneously or sequentially. The first four valid consecutive measurement results, within 2 dB(A), allowing for the deletion of non-valid results (see paragraph 2.1), shall be used for the calculation of the final result for the given side of the vehicle. The results of each side shall be averaged separately and rounded to the first decimal place. All further calculations to derive L shall be done separately for the left and right vehicle side. The final urban value to be reported as the test result mathematically rounded to the nearest integer shall be the higher value of the two sides.4.6.2018 EN Official Journal of the European Union L 138/39 The speed measurements at AA′, BB′, and PP′ shall be noted and used in calculations to the first significant digit after the decimal place. The calculated acceleration a shall be noted to the second digit after the decimal place. wot test 3.1.3.1. Vehicles of categories M , N and M ≤ 3 500 kg technically permissible maximum laden mass 1 1 2 The calculated values for the acceleration test and the constant speed test are given by: L = L + k * (L – L ) wot rep wot (i + 1) wot(i) wot (i + 1) L = L + k * (L – L ) crs rep crs(i + 1) crs (i) crs (i + 1) Where k = (a – a )/(a – a ) wot ref wot (i + 1) wot (i) wot (i + 1) In the case of a single gear ratio test the values are the test result of each test. The final result is calculated by combining L and L . The equation is: wot rep crs rep L = L – k * (L – L ) urban wot rep P wot rep crs rep The weighting factor k gives the part power factor for urban driving. In cases other than a single gear test, P k is calculated by: P k = 1 – (a /a ) P urban wot ref If only one gear was specified for the test, k is given by: P k = 1 – (a /a ) P urban wot test In cases where a is less than a : wot test urban k = 0 P 3.1.3.2. Vehicles of categories M > 3 500 kg technically permissible maximum laden mass, M , N , N 2 3 2 3 When the result of one test condition is used the final result L is equal to the intermediate result. urban When the results of two test conditions are used the arithmetic mean of the intermediate results of the two averages for each side of the two conditions shall be calculated. The final result L is the higher value of urban the two calculated averages. 3.2. Measurement of sound emitted by stationary vehicles 3.2.1. Sound level in the vicinity of vehicles The measurement results shall be entered into the Addendum to the Communication form (Annex 1, Appendix 1). 3.2.2. Acoustic measurements A precision sound level meter as defined in paragraph 1.1 of this annex shall be used for the measurements. 3.2.3. Test site — local conditions (see appendix of Annex 3, Figure 2) 3.2.3.1. In the vicinity of the microphone, there shall be no obstacle that could influence the acoustical field and no person shall remain between the microphone and the sound source. The meter observer shall be positioned so as not to influence the meter reading.L 138/40 EN Official Journal of the European Union 4.6.2018 3.2.4. Disturbance noise and wind interference Readings on the measuring instruments produced by ambient noise and wind shall be at least 10 dB(A) below the sound level to be measured. A suitable windscreen may be fitted to the microphone provided that account is taken of its effect on the sensitivity of the microphone (see paragraph 1.1. of this annex). 3.2.5. Measuring method 3.2.5.1. Nature and number of measurements The maximum sound level expressed in A-weighted decibels (dB(A)) shall be measured during the operating period referred to in paragraph 3.2.5.3.2.1. At least three measurements shall be taken at each measuring point. 3.2.5.2. Positioning and preparation of the vehicle The vehicle shall be located in the centre part of the test area with the gear selector in neutral position and the clutch engaged. If the design of the vehicle does not allow this, the vehicle shall be tested in conformity with the manufacturer's prescriptions for stationary engine testing. Before each series of measurements, the engine shall be brought to its normal operating condition, as specified by the manufacturer. If the vehicle is fitted with fan(s) having an automatic actuating mechanism, this system shall not be interfered with during the sound level measurements. The engine hood or compartment cover, if so fitted, shall be closed. 3.2.5.3. Measuring of noise in proximity to the exhaust (see appendix of Annex 3, Figure 2) 3.2.5.3.1. Positions of the microphone 3.2.5.3.1.1. The microphone shall be located at a distance of 0,5 m ± 0,01 m from the reference point of the exhaust pipe defined in Figure 2 and at an angle of 45° (± 5°) to the vertical plane containing the flow axis of the pipe termination. The microphone shall be at the height of the reference point, but not less than 0,2 m from the ground surface. The reference axis of the microphone shall lie in a plane parallel to the ground surface and shall be directed towards the reference point on the exhaust outlet. If two microphone positions are possible, the location farthest laterally from the vehicle longitudinal centreline shall be used. If the flow axis of the exhaust outlet pipe is at 90° to the vehicle longitudinal centreline, the microphone shall be located at the point, which is furthest from the engine. 3.2.5.3.1.2. For vehicles having an exhaust provided with outlets spaced more than 0,3 m apart, one measurement is made for each outlet. The highest level shall be recorded. 3.2.5.3.1.3. In the case of an exhaust provided with two or more outlets spaced less than 0,3 m apart and which are connected to the same silencer; the microphone position is related to the outlet nearest to one extreme edge of the vehicle or, when such outlet does not exist, to the outlet, which is highest above the ground. 3.2.5.3.1.4. For vehicles with a vertical exhaust (e.g. commercial vehicles) the microphone shall be placed at the height of the exhaust outlet. Its axis shall be vertical and oriented upwards. It shall be placed at a distance of 0,5 m ± 0,01 m from the exhaust pipe reference point, but never less than 0,2 m from the side of the vehicle nearest to the exhaust.4.6.2018 EN Official Journal of the European Union L 138/41 3.2.5.3.1.5. For exhaust outlets located under the vehicle body, the microphone shall be located a minimum of 0,2 m from the nearest part of the vehicle, at a point closest to, but never less than 0,5 m from the exhaust pipe reference point, and at a height of 0,2 m above the ground, and not in line with the exhaust flow. The angularity requirement in paragraph 3.2.5.3.1.1 may not be met in some cases. 3.2.5.3.1.6. Examples of the position of the microphone, depending on the location of the exhaust pipe, are given in Figures 3a-3d in the Appendix to Annex 3. 3.2.5.3.2. Operating conditions of the engine 3.2.5.3.2.1. Target engine speed The target engine speed is defined as: (a) 75 per cent of the rated engine speed S for vehicles with a rated engine speed ≤ 5 000 min– 1; (b) 3 750 min– 1 for vehicles with a rated engine speed above 5 000 min– 1 and below 7 500 min– 1; (c) 50 per cent of the rated engine speed S for vehicles with a rated engine speed ≥ 7 500 min– 1. If the vehicle cannot reach the engine speed as stated above, the target engine speed shall be 5 per cent below the maximum possible engine speed for that stationary test. 3.2.5.3.2.2. Test procedure The engine speed shall be gradually increased from idle to the target engine speed, not exceeding the tolerance band of ± 3 per cent of the target engine speed, and held constant. Then the throttle control shall be rapidly released and the engine speed shall be returned to idle. The sound pressure level shall be measured during a period of operation consisting of a maintaining constant engine speed of 1 second and throughout the entire deceleration period. The maximum sound level meter reading during this period of operation, mathematically rounded to the first decimal place, is taken as the test value. 3.2.5.3.2.3. Test validation The measurement shall be regarded as valid if the test engine speed does not deviate from the target engine speed by more than ± 3 per cent for at least 1 second. 3.2.6. Results At least three measurements for each test position shall be made. The maximum A-weighted sound pressure level indicated during each of the three measurements shall be recorded. The first three valid consecutive measurement results, within 2 dB(A), allowing for the deletion of non-valid results (see paragraph 2.1 except the specifications of the test site), shall be used for the determination of the final result for the given measurement position. The maximum sound level, for all measurement positions, and of the three measurement results, constitutes the final result. 4. Sound from the hybrid vehicle of categories M in motion, where an internal combustion engine cannot 1 operate when the vehicle is stationary (data reported to facilitate testing of the vehicle in use). 4.1. In order to facilitate in-use compliance test of hybrid vehicles — where an internal combustion engine cannot operate when the vehicle is stationary — the following information relating to the sound-pressure level measurements carried out in accordance with paragraph 3.1 of Annex 3 for the motor vehicles in motion is referred to as in-use compliance reference data: (a) Gear (i) or, for vehicles tested with non-locked gear ratios, the position of the gear selector chosen for the test; (b) Position of the operating switch during measurement of the sound pressure level L (if switch is wot (i) fitted); (c) The pre-acceleration length lPA in m;L 138/42 EN Official Journal of the European Union 4.6.2018 (d) The average vehicle speed in km/h at the beginning of the full throttle acceleration for tests in gear (i); and (e) The sound pressure level L in dB(A) of the wide-open-throttle tests in gear (i), defined as the wot (i) maximum of the two values resulting from averaging the individual measurement results at each microphone position separately. 4.2. The in-use compliance reference data shall be entered in the type approval certificate as specified in paragraph 2.3 of the Addendum to the Communication form (Annex 1, Appendix 1).4.6.2018 EN Official Journal of the European Union L 138/43 Appendix Figure 1 Measuring positions for vehicles in motion Figure 2 Reference point for measurement of sound emitted by stationary vehicles Key: T = top view S = side view 1 = reference point 2 = road surface A = mitred pipe B = bent down pipe C = straight pipe D = vertical pipeL 138/44 EN Official Journal of the European Union 4.6.2018 Figure 3a Figure 3b Figure 3c Figure 3d4.6.2018 EN Official Journal of the European Union L 138/45 Figure 3a Flowchart for vehicles tested according to paragraph 3.1.2.1 of Annex 3 to this Regulation — L urban computationL 138/46 EN Official Journal of the European Union 4.6.2018 Figure 3b Flowchart for vehicles tested according to paragraph 3.1.2.1 of Annex 3 to this Regulation — Gear selection using locked gear PART 14.6.2018 EN Official Journal of the European Union L 138/47 Figure 3c Flowchart for vehicles tested according to paragraph 3.1.2.1 of Annex 3 to this Regulation — Gear selection using locked gear PART 2L 138/48 EN Official Journal of the European Union 4.6.2018 Figure 3d Flowchart for vehicles tested according to paragraph 3.1.2.1 of Annex 3 to this Regulation — Gear selection using locked gear PART 34.6.2018 EN Official Journal of the European Union L 138/49 Figure 3e Flowchart for vehicles tested according to paragraph 3.1.2.1 of Annex 3 to this Regulation — Gear Selection using non-locked gearsL 138/50 EN Official Journal of the European Union 4.6.2018 Figure 4a* Flowchart for vehicles tested according to paragraph 3.1.2.2 of Annex 3 to this Regulation — Test in locked gears4.6.2018 EN Official Journal of the European Union L 138/51 Figure 4b* Flowchart for vehicles tested according to paragraph 3.1.2.2 of Annex 3 to this Regulation — Test in non-locked gears PART 1L 138/52 EN Official Journal of the European Union 4.6.2018 Figure 4c* Flowchart for vehicles tested according to paragraph 3.1.2.2 of Annex 3 to this Regulation — Test in non-locked gears PART 24.6.2018 EN Official Journal of the European Union L 138/53 Figure 4d* Flowchart for vehicles tested according to paragraph 3.1.2.2 of Annex 3 to this Regulation — Test for no combustion engine speed available Note: * Broaden the window for the target vehicle speed v for vehicles of category M > 3 500 kg technically target BB′ 2 permissible maximum laden mass and for vehicles of category N , M and N . 2 3 3 The target vehicle velocity v is defined as v = 35 km/h ± 5 km/h which results in a window for the target BB′ target BB′ velocity v , when the reference point passes line BB′, from 30 km/h to 40 km/h. If the target vehicle velocity v BB′ target BB′ is changed into two target vehicle velocities, a lower and a higher one, the following is meant: The lower target vehicle velocity is defined as the target vehicle velocity v reduced by 5 km/h (v – 5 km/h) which results in target BB′ target BB′ a window for the velocity v , when the reference point passes line BB′, from 25 km/h to 35 km/h. BB′1 25 km/h ≤ v ≤ 35 km/h. BB′1 The higher target vehicle velocity is defined as the target vehicle velocity v increased by 5 km/h (v + target BB′ target BB′ 5 km/h) which results in a window for the velocity v , when the reference point passes line BB′, from 35 km/h to BB′2 45 km/h. 35 km/h ≤ v ≤ 45 km/h. BB′2L 138/54 EN Official Journal of the European Union 4.6.2018 ANNEX 4 EXHAUST SILENCING SYSTEMS CONTAINING ACOUSTICALLY ABSORBING FIBROUS MATERIALS 1. General Sound absorbing fibrous materials may be used in silencing systems or components thereof only if (a) The exhaust gas is not in contact with the fibrous materials; or if (b) The silencing system or components thereof are of the same design family as systems or components for which it has been proven, in the course of type approval process in accordance with the requirements of this regulation for another vehicle-type, that they are not subject to deterioration. Unless one of these conditions is fulfilled, the complete silencing system or components thereof shall be submitted to a conventional conditioning using one of three installations and procedures described below. 1.1. Continuous road operation for 10 000 km 1.1.1. 50 ± 20 per cent of this operation shall consist of urban driving and the remaining operation shall be long-distance runs at high speed; continuous road operation may be replaced by a corresponding test-track programme. 1.1.2. The two speed regimes shall be alternated at least twice. 1.1.3. The complete test programme shall include a minimum of 10 breaks of at least three hours duration in order to reproduce the effects of cooling and any condensation which may occur. 1.2. Conditioning on a test bench 1.2.1. Using standard parts and observing the vehicle manufacturer's instructions, the silencing system or components thereof shall be fitted to the vehicle referred to in paragraph 3.3 of this Regulation or the engine referred to in paragraph 3.4 of this Regulation. In the former case the vehicle shall be mounted on a roller dynamometer. In the second case, the engine shall be coupled to a dynamometer. 1.2.2. The test shall be conducted in six six-hour periods with a break of at least 12 hours between each period in order to reproduce the effects of cooling any condensation which may occur. 1.2.3. During each six-hour period, the engine shall be run, under the following conditions: (a) Five minutes at idling speed; (b) One-hour sequence under 1/4 load at 3/4 of rated maximum speed (S); (c) One-hour sequence under 1/2 load at 3/4 of rated maximum speed (S); (d) 10-minute sequence under full load at 3/4 of rated maximum speed (S); (e) 15-minute sequence under 1/2 load at rated maximum speed (S); (f) 30-minute sequence under 1/4 load at rated maximum speed (S). Each period shall comprise two sequenced sets of the six above-mentioned conditions in consecutive order from (a) to (f). 1.2.4. During the test, the silencing system or components thereof shall not be cooled by a forced draught simulating normal airflow around the vehicle. Nevertheless, at the request of the manufacturer, the silencing system or components thereof may be cooled in order not to exceed the temperature recorded at its inlet when the vehicle is running at maximum speed. 1.3. Conditioning by pulsation 1.3.1. The silencing system or components thereof shall be fitted to the vehicle referred to in paragraph 3.3 of this Regulation or the engine referred to in paragraph 3.4 of this Regulation. In the former case the vehicle shall be mounted on a roller dynamometer.4.6.2018 EN Official Journal of the European Union L 138/55 In the second case, the engine shall be mounted on a dynamometer. The test apparatus, a detailed diagram of which is shown in Figure 1 of the appendix to this annex shall be fitted at the outlet of the silencing system. Any other apparatus providing equivalent results is acceptable. 1.3.2. The test apparatus shall be adjusted in such a way that the exhaust-gas flow is alternatively interrupted and re-established by the quick-action valve for 2 500 cycles. 1.3.3. The valve shall open when the exhaust-gas back pressure, measured at least 100 mm downstream of the intake flange, reaches a value of between 35 and 40 kPa. It shall close when this pressure does not differ by more than 10 per cent from its stabilised value with the valve open. 1.3.4. The time-delay switch shall be set for the duration of gas exhaust resulting from the provisions laid down in paragraph 1.3.3 above. 1.3.5. Engine speed shall be 75 per cent of the rated engine speed (S) at which the engine develops rated maximum net power. 1.3.6. The power indicated by the dynamometer shall be 50 per cent of the full-throttle power measured at 75 per cent of rated engine speed (S). 1.3.7. Any drain holes shall be closed off during the test. 1.3.8. The entire test shall be completed within 48 hours. If necessary, one cooling period will be observed after each hour.L 138/56 EN Official Journal of the European Union 4.6.2018 Appendix Figure 1 Test apparatus for conditioning by pulsation 1. Inlet flange or sleeve for connection to the rear of the test exhaust system. 2. Hand-operated regulating valve. 3. Compensating reservoir with a maximum capacity of 40 l and a filling time of not less than one second. 4. Pressure switch with an operating range of 0,05 to 2,5 bar. 5. Time delay switch. 6. Pulse counter. 7. Quick-acting valve, such as exhaust brake valve 60 mm in diameter, operated by a pneumatic cylinder with an output of 120 N at 4 bar. The response time, both when opening and closing, shall not exceed 0,5 second. 8. Exhaust gas evacuation. 9. Flexible pipe. 10. Pressure gauge.4.6.2018 EN Official Journal of the European Union L 138/57 ANNEX 5 COMPRESSED AIR NOISE 1. Method of measurement The measurement is performed at microphone positions 2 and 6 according to Figure 1, with the vehicle stationary. The highest A-weighted sound level is registered during venting the pressure regulator and during ventilating after the use of both the service and parking brakes. The noise during venting the pressure regulator is measured with the engine at idling speed. The ventilating noise is registered while operating the service and parking brakes; before each measurement, the air-compressor unit has to be brought up to the highest permissible operating pressure, and then the engine switched off. 2. Evaluation of the results For all microphone positions two measurements are taken. In order to compensate for inaccuracies of the measuring equipment, the meter reading is reduced by 1 dB(A), and the reduced value is taken as the result of measurement. The results are taken as valid if the difference between the measurements at one microphone position does not exceed 2 dB(A). The highest value measured is taken as the result. If this value exceeds the sound limit by 1 dB(A), two additional measurements are to be taken at the corresponding microphone position. In this case, three out of the four results of measurement obtained at this position have to comply with the sound limit. 3. Limiting value The sound level shall not exceed the limit of 72 dB(A).L 138/58 EN Official Journal of the European Union 4.6.2018 Appendix Figure 1 Microphone positions for measurement of compressed air noise The measurement is performed at the stationary vehicle according to Figure 1, using two microphone positions at a distance of 7 m from the contour of the vehicles, and at 1,2 m above ground.4.6.2018 EN Official Journal of the European Union L 138/59 ANNEX 6 CHECKS ON CONFORMITY OF PRODUCTION 1. General These requirements are consistent with the test for checking Conformity of Production (COP) according to paragraph 8. of this Regulation. 2. Testing procedure The test site and measuring instruments shall be those as described in Annex 3. 2.1. The vehicle(s) under test shall be subjected to the test for measurement of sound of vehicle in motion as described in paragraph 3.1 of Annex 3. 2.2. Compressed air noise Vehicles having maximum mass exceeding 2 800 kg and equipped with compressed air systems shall be subjected to an additional test for measurement of the compressed air noise as described in paragraph 1 of Annex 5. 2.3. Additional Sound Emission Provisions (ASEP) The vehicle manufacturer shall assess the compliance with ASEP by an appropriate evaluation (for example, but not limited to, part checks) or may perform the test described in Annex 7. 3. Sampling and evaluation of the results One vehicle shall be chosen and subjected to the tests set out in point 2. If the sound level of the vehicle tested does not exceed by more than 1 dB(A) the limit value prescribed in Annex 3, and, where appropriate, paragraph 3 of Annex 5, the vehicle type shall be considered to conform to the requirements of this Regulation. If one of the test results does not fulfil the COP requirements of this annex and of paragraph 8 of the main body of this Regulation two more vehicles of the same type shall be tested pursuant to paragraph 2 above. If the test results for the second and the third vehicle fulfil the COP requirements of this annex and of paragraph 8 of the main body of this Regulation, the vehicle is considered in compliance with regard to the COP. If one of the test results of the second or third vehicle does not fulfil the COP requirements of this annex and of paragraph 8 of the main body of this Regulation the vehicle type shall be considered not to conform to the requirements of this Regulation and the manufacturer shall take the necessary measures to re-establish the conformity.L 138/60 EN Official Journal of the European Union 4.6.2018 ANNEX 7 MEASURING METHOD TO EVALUATE COMPLIANCE WITH THE ADDITIONAL SOUND EMISSION PROVISIONS Only applicable for vehicles as specified in paragraph 6.2.3 of this Regulation. 1. General (see the flowchart in Appendix 2, Figure 1) This annex describes a measurement method to evaluate compliance of the vehicle with the additional sound emission provisions (ASEP) conforming to paragraph 6.2.3 of this Regulation. It is not mandatory to perform actual tests when applying for type-approval. The manufacturer shall sign the declaration of compliance set out in Appendix 1. The approval authority may ask for additional information about the declaration of compliance and carry out the tests described below. The procedure set out in this annex requires the performance of a test in accordance with Annex 3. If the tests according to Annex 7 are carried out in the course of type approval, all tests either for Annex 3 and for Annex 7 shall be carried out on the same test track and under similar environmental conditions (1). If Annex 7 tests are carried out when type approval has already been granted, e.g. during tests for conformity of production or for in-use compliance, the tests in motion specified in Annex 3 shall be carried out with the same mode, gear(s)/gear ratio(s), gear weighting factor k and partial power factor k as determined during the type P approval process. 2. Measurement method (see the flowchart in Appendix 2, Figure 3) 2.1. Measurement instruments and condition of measurements Unless otherwise specified, the measurement instruments, the conditions of the measurements and the condition of the vehicle are equivalent to those specified in Annex 3, paragraphs 1 and 2. If the vehicle has different modes which affect sound emission, all modes shall comply with the requirements in this annex. In the case where the manufacturer has performed tests to prove to the approval authority compliance with the above requirements, the modes used during those tests shall be reported in a test report. 2.2. Method of testing Unless otherwise specified, the conditions and procedures of Annex 3 shall be used. For the purpose of this annex, one run per test condition is measured and evaluated. 2.3. Control range The ASEP requirements apply to every gear ratio κ that leads to test results within the control range as defined below. Vehicle speed V : v ≥ 20 km/h AA_ASEP AA Vehicle acceleration a : a ≤ 5,0 m/s2 WOT_ASEP WOT Engine speed n n ≤ 2,0 * PMR– 0,222 * S or BB_ASEP BB n ≤ 0,9 * S, whichever is the lowest BB Vehicle speed V : BB_ASEP If the vehicle in the lowest valid gear does not achieve the maximum engine speed n below 70 km/h, BB_ASEP increase the vehicle speed in that gear to reach the maximum engine speed n , but not beyond 80 km/h. BB_ASEP (1) Measurements for Annex 7 for a particular vehicle type may be carried out on a different test tracks or under different environmental conditions, each according to the provisions of this Regulation, if the test results Lwoti and Lcrsi for the gear i, representing the anchor point, do not differ by more the +/– 1,0 dB from the test results at the time when the tests according to Annex 3 have been carried out.4.6.2018 EN Official Journal of the European Union L 138/61 For any other gear, the maximum vehicle speed is 70 km/h. For vehicles tested in non-locked transmission conditions, the maximum vehicle speed is 80 km/h. Gears κ ≤ gear i as determined in Annex 3 Transmission conditions: Annex 3 gear selection Annex 7 gear selection Locked Gear, i gear , … i – 1 Non-locked Non-locked 2.4. Target conditions The sound emission shall be measured in each valid gear ratio at the four test points as specified below. For all test points the boundary conditions as specified in paragraph 2.3 shall be met. The gear ratio is valid if all four points and the anchor point meet the specifications of paragraph 2.3 above. Any gear ratio for which this criteria is not fulfilled is invalid and not analysed further. The first test point P is defined by using an entry speed v of 20 km/h ≤ v < 20 km/h + 3 km/h. 1 AA,κ1 AA,κ1 For P , if a stable acceleration condition cannot be achieved according to 2.26.2.1 in the definition section of this 1 Regulation, the speed v shall be increased in steps of 5 km/h until a stable acceleration is reached. AA,κ1 For all points, if a stable acceleration condition cannot be achieved according to 2.26.1 the acceleration a wot_testPP-BB shall be calculated according the formula given in paragraph 3.1.2.1.2 of Annex 3. In case of non-locked transmission conditions where n is exceeded during the test, the following measures BB_ASEP shall be considered separately or together: — provisions of paragraph 2.5.1 — increased speed in steps of 5 km/h. The test speed for the fourth test point P in any gear is defined by either 4 — 0,95 × n ≤ n ≤ n or BB_ASEP BB,κ4 BB_ASEP — v – 3 km/h ≤ V ≤ V with V as defined in paragraph 2.3. BB_ASEP BB,κ4 BB_ASEP BB_ASEP The test speed for the other two test points is defined by the following formula: Test Point P: v = v + ((j – 1)/3) * (v – v ) for j = 2 and 3 with a tolerance of ± 3 km/h j BB,κj BB,κ1 BB,κ4 BB,κ1 Where: v = vehicle speed at BB′ of test point P BB,κ1 1 v = vehicle speed at BB′ of test point P BB,κ4 4 2.5. Test of the vehicle 2.5.1. The path of the centreline of the vehicle shall follow line CC′ as closely as possible throughout the entire test, starting from the approach of the reference point according to definition 2.11 of the main body to line AA′ until the rear of the vehicle passes line BB′.L 138/62 EN Official Journal of the European Union 4.6.2018 At line AA′ the accelerator shall be fully depressed. To achieve a more stable acceleration or to avoid a downshift between line AA′ and BB′ pre-acceleration before line AA′ may be used according to the provisions of paragraphs 3.1.2.1.2.1 and 3.1.2.1.2.2 of Annex 3. The accelerator shall be kept in depressed condition until the rear of the vehicle reaches line BB′. In case of non-locked transmission conditions, the test may include a gear ratio change to a lower range and a higher acceleration. A gear change to a higher range and a lower acceleration is not allowed. If possible, the manufacturer shall take measures to avoid that a gearshift leads to a condition not in compliance with the boundary conditions. For that, it is permitted to establish and use electronic or mechanical devices, such as alternate gear selector positions. If no such measures can be applied, the rationale shall be provided and documented in the technical report. 2.5.2. Measurements reading: Per test point, one single run is carried out. For every separate test run, the following parameters shall be determined and noted: The maximum A-weighted sound pressure level of both sides of the vehicle, indicated during each passage of the vehicle between the two lines AA′ and BB′, shall be mathematically rounded to the first decimal place (L ). If wot,κj a sound peak obviously out of character with the general sound pressure level is observed, the measurement shall be discarded. Left and right side may be measured simultaneously or separately. For further processing, the higher sound pressure level of both sides shall be used. The vehicle speed readings at AA′, PP′ and BB′ shall be rounded and reported with the first significant digit after the decimal place. (v ; v ; v ) AA,κj PP,κj BB,κj If applicable, the engine speed readings at BB′ shall be reported as a full integer value (n ). BB,κj 2.5.3. The calculated acceleration shall be determined in accordance to the formula in paragraph 3.1.2.1.2 of Annex 3 and reported to the second digit after the decimal place (a ). wot,test,κj 3. Analysis method 1: Slope-Assessment 3.1. Determination of the anchor point The anchor point is the same for each gear ratio κ falling under the control range according to paragraph 2.3. The parameters for the anchor point are taken from the acceleration test of Annex 3 as follows: L is the higher sound pressure level of L of left and right side of gear ratio i; anchor wot,(i) n is the average of n of the 4 runs of gear ratio i reported from Annex 3; anchor BB,wot 3.2. Slope of the regression line for each gear ratio κ The sound measurements shall be evaluated as function of engine speed according to paragraph 3.2.1. 3.2.1. Calculation of the slope of the regression line for each gear ratio κ The linear regression line is calculated using the anchor point and the four correlated additional measurements with the results for engine speeds and sound levels as reported under 2.5.2 of this annex. P5 ðn − nÞðL − LÞ j j j¼1 Slope ¼ (in dB(A)/1 000 min– 1) k P5 ðn − nÞ2 j j¼1 X5 X5 1 1 With L¼ L and n¼ n; 5 j 5 j j¼1 j¼1 where n = engine speed measured at line BB′ j4.6.2018 EN Official Journal of the European Union L 138/63 3.2.2. Slope of the regression line for each gear ratio κ The slope of a particular gear for the further calculation is the derived result of the calculation in κ paragraph 3.2.1 rounded to the first decimal place, but not higher than 5 dB(A)/1 000 min– 1. In case of non-locked conditions, if Slope < 0, the selected transmission setup is not valid. In that case the κ L -Assessment as specified in paragraph 4 shall be applied. urban 3.3. Calculation of the linear sound level increase expected for each measurement The sound level L for measurement point j and gear ratio κ shall be calculated using the engine speeds ASEP,κj measured for each measurement point, using the slope specified in paragraph 3.2 above to the specific anchor point for each gear ratio. For n ≤ n : BB_κ,j anchor L = L + (Slope – Y) * (n – n )/1 000 ASEP_κ,j anchor κ BB_κ,j anchor For n > n : BB_κ,j anchor L = L + (Slope + Y) * (n – n )/1 000 ASEP_κ,j anchor κ BB_κ,j anchor Where Y= 1 3.4. Additional samples On request of the type approval authority, two additional runs within the boundary conditions according to paragraph 2.3 of this annex shall be carried out. 3.5. Specifications Every individual sound measurement shall be evaluated. The sound level of every specified measurement point shall not exceed the limits given below: L ≤ L + x κj ASEP_κ.j With: x = 3 dB(A) + limit value (1) – L for vehicle tested with non-locked transmission conditions urban x = 2 dB(A) + limit value (1) – L for vehicles tested with locked transmission conditions urban If the measured sound level at a point exceeds the limit, two additional measurements at the same point shall be carried out to verify the measurement uncertainty. The vehicle is still in compliance with ASEP, if the average of the three valid measurements at this specific point fulfils the specification. 4. Analysis method 2: L Assessment urban 4.1. General This evaluation procedure is an alternative selected by the vehicle manufacturer to the procedure described in paragraph 3 of this annex and is applicable for all vehicle technologies. It is the responsibility of the vehicle manufacturer to determine the correct manner of testing. Unless otherwise specified, all testing and calculation shall be as specified in Annex 3 to this Regulation. The measurement method is defined in paragraph 2. Each testing point shall be evaluated individually. 4.2. Calculation of ΔL urban_ASEP 4.2.1. Data-processing From any L as measured according to this annex, ΔL shall be calculated as follows: wot_ASEP urban_ASEP (a) Calculate a using acceleration calculation from paragraph 3.1.2.1.2.1 or 3.1.2.1.2.2 of Annex 3 to wot_test_ASEP this Regulation, as applicable; (1) As applicable for the approved type of vehicleL 138/64 EN Official Journal of the European Union 4.6.2018 (b) Determine the vehicle speed (v ) at BB during the L test; BB_ASEP wot_ASEP (c) Calculate k as follows: P_ASEP k = 1 – (a /a ) P_ASEP urban wot_test_ASEP Test results where a are less than a shall be disregarded. wot_test_ASEP urban (d) Calculate L as follows: urban_measured_ASEP L = L – k * (L – L ) urban_measured_ ASEP wot_ASEP P_ASEP wot_ASEP crs rep For further calculation, use the L from Annex 3 to this Regulation without rounding, including the digit urban after the decimal (xx,x). (e) Calculate L to normalise the speed from v to 50 km/h as follows: urban_normalised BB_ASEP L = L – (0,15 * (V – 50)) urban_normalised urban_measured_ASEP _BB_ASEP (f) Calculate the deviation ΔL relative to L as follows: urban_ASEP urban ΔL = L – L urban_ASEP urban_normalised urban 4.2.2. Specifications Compliance with limits: ΔL shall be less than or equal to 3,0 dB(A) + limit value (1) – L . urban_ASEP urban 5. Reference sound assessment (see the flowchart in Appendix 2, Figure 2) 5.1. General The reference sound can be obtained by simulation or from direct measurement. The result of one assessment method has to comply with the specification of paragraph 5.4. 5.1.1. Simulation method (2) For simulation, the reference sound is assessed at a single point in one discrete gear, simulating an acceleration condition assuming an exit speed v equal to 61 km/h. The sound compliance is calculated using the slope BB′ results of paragraph 3.2.2. If the result of slope of 3.2.2 is not available for the gear specified in paragraph 5.2, this slope of the missing gear can be determined according to paragraphs 2.4, 3.1 and 3.2. 5.1.2. Direct measurement method For direct measurement, the reference sound is assessed at a single run in an acceleration condition started at line AA′ as specified in paragraph 2.5. The gear shall be as specified in paragraph 5.2 for vehicles tested in locked condition or in a gear selector position for normal driving as specified by the manufacturer for vehicles tested in non-locked condition. The target test speed v is equal to 50 km/h ± 1 km/h unless v exceeds 61 km/h. AA BB If v exceeds 61 km/h, the target test speed v shall be set to 61 km/h ± 1 km/h. The entry speed shall be BB BB adjusted to achieve the target test speed. 5.2. The determination of gear α is as follows: α = 3 for all manual transmission and for automatic transmission tested in locked position with up to 5 gears; α = 4 for automatic transmission tested in locked position with 6 or more gears. If the acceleration calculated from AA to BB + vehicle length in gear 4 exceeds 1,9 m/s2, the first higher gear α > 4 with an acceleration lower than or equal to 1,9 m/s2 shall be chosen. (1) As applicable for the approved type of vehicle (2) Simulation may not always be applicable as the test result of Annex 3 and the elaborated slopes according to paragraph 3 of Annex 7 might not provide consistent data for the simulation. In that case, it is recommended to carry out direct measurements.4.6.2018 EN Official Journal of the European Union L 138/65 For vehicles tested under non-locked condition, the gear ratio for further calculation shall be determined from the acceleration test result in Annex 3 using the reported engine speed and vehicle speed at line BB′. 5.3. Data-processing for simulation assessment 5.3.1. Determination of reference engine speed n BB′_ref_α The reference engine speed, n shall be calculated using the gear ratio of gear α at the reference speed of BB′_ref_α, v = 61 km/h. BB′_ref 5.3.2. Calculation of L ref L = L + Slope * (n – n )/1 000 ref anchor α BB′_ref_α anchor 5.4. Specifications For vehicles of category M , L shall be less than or equal to 76 dB(A). 1 ref For vehicles of category M fitted with a manual transmission having more than four forward gears and equipped 1 with an engine developing a rated maximum net power greater than 140 kW (according to Regulation No 85) and having a maximum-power/maximum-mass ratio greater than 75, L shall be less than or equal to 79 dB(A). ref For vehicles of category M fitted with an automatic transmission having more than four forward gears and 1 equipped with an engine developing a rated maximum net power greater than 140 kW (according to Regulation No 85) and having a maximum-power/maximum-mass ratio greater than 75, L shall be less than or equal to ref 78 dB(A). For vehicles of category N with a technically permissible maximum laden mass below 2 000 kg, L shall be less 1 ref than or equal to 78 dB(A). For vehicles of category N with a technically permissible maximum laden mass above 2 000 kg and below 1 3 500 kg, L shall be less than or equal to 79 dB(A). ref For vehicles of category M and N equipped with a compression-ignition and direct injection internal 1 1 combustion engine, the sound level shall be increased by 1 dB(A). For vehicles of category M and N designed for off-road use and with a technically permissible maximum laden 1 1 mass above 2 tonnes, the sound level shall be increased by 1 dB(A) if they are equipped with an engine having a rated maximum net power of less than 150 kW (according to Regulation No 85) or by 2 dB(A) if they are equipped with an engine having a rate maximum net power of 150 kW (according to Regulation No 85) or higher.L 138/66 EN Official Journal of the European Union 4.6.2018 Appendix 1 Statement of compliance with the additional sound emission provisions (Maximum format: A4 (210 × 297 mm)) .................................... (Name of manufacturer) attests that vehicles of this type (type with regard to its sound emission pursuant to Regulation No 51) comply with the requirements of paragraph 6.2.3 of Regulation No 51. ............................... (Name of manufacturer) makes this statement in good faith, after having performed an appropriate evaluation of the sound emission performance of the vehicles. Date: ......................................................................................................................................................................... Name of authorised representative: ............................................................................................................................. Signature of authorised representative: ........................................................................................................................4.6.2018 EN Official Journal of the European Union L 138/67 Appendix 2 Figure 1 Flowchart for the assessment concept for ASEP according to Annex 7L 138/68 EN Official Journal of the European Union 4.6.2018 Figure 2 Flowchart for the vehicle sound assessment according to Annex 7, paragraph 5 ‘Reference sound assessment’4.6.2018 EN Official Journal of the European Union L 138/69 Figure 3 Flowchart for the determination of the individual test points P according to Annex 7, paragraph 2 j ‘Measurement method’