See Full Document Text
16.11.2018 EN Official Journal of the European Union L 290/1
II
(Non-legislative acts)
ACTS ADOPTED BY BODIES CREATED BY
INTERNATIONAL AGREEMENTS
Only the original UN/ECE texts have legal effect under international public law. The status and date of entry into force of this Regulation
should be checked in the latest version of the UN/ECE status document TRANS/WP.29/343, available at:
http://www.unece.org/trans/main/wp29/wp29wgs/wp29gen/wp29fdocstts.html
Regulation No 9 of the Economic Commission for Europe of the United Nations (UNECE) —
Uniform provisions concerning the approval of category L , L and L vehicles with regard to
2 4 5
sound emission [2018/1704]
Incorporating all valid text up to:
Supplement 3 to the 07 series of amendments – Date of entry into force: 10 October 2017
CONTENTS
REGULATION
1. Scope
2. Definitions
3. Application for approval
4. Markings
5. Approval
6. Specifications
7. Modification and extension of approval of a vehicle type or a type of exhaust or silencing system(s)
8. Conformity of production
9. Penalties for non-conformity of production
10. Production definitively discontinued
11. Transitional provisions
12. Names and addresses of Technical Services responsible for conducting approval tests, and of Type Approval
Authorities
Annexes
1. Communication
2. Arrangements of the approval mark
3. Methods and instruments for measuring the sound made by motor vehicles
4. Maximum sound level limits (new vehicles)
5. Specifications for the test siteL 290/2 EN Official Journal of the European Union 16.11.2018
1. SCOPE
This Regulation applies to vehicles of category L , L and L (1) with regard to sound emission.
2 4 5
2. DEFINITIONS
For the purposes of this Regulation,
2.1. ‘Approval of a vehicle’ means the approval of a vehicle type with regard to the sound level and the original
exhaust system as a technical unit of a vehicle type, falling under the scope of this Regulation.
2.2. ‘Vehicle type’ means a category of motor vehicles which do not differ in such essential respects as:
2.2.1. The lines and constituent materials of the body (more particularly the engine compartment and its
soundproofing);
2.2.2. The length and width of the vehicle;
2.2.3. The type of engine (positive ignition or compression ignition; reciprocating or rotary piston; number and
capacity of cylinders; number and type of carburettors or injection systems, arrangement of valves; rated
maximum net power and rated engine speed).
For rotary piston engines, the cubic capacity should be taken to be double of the volume of the chamber.
2.2.4. The electric motor in case of a hybrid electric vehicle.
2.2.5. Drive train, in particular the number and ratios of the gears of the transmission and the final ratio.
2.2.6. The number, type and arrangement of exhaust systems.
2.3. ‘Rated maximum net power’ of the combustion engine means the rated engine power as defined in
ISO 4106:2012.
The symbol P denotes the numerical value of the rated maximum net power expressed in kW.
n
2.4. ‘Rated engine speed’ of the combustion engine means the engine speed at which the engine develops its rated
maximum net power as stated by the manufacturer (2).
The symbol n denotes the rated engine speed expressed in min– 1.
rated
2.5. ‘Exhaust or silencing system(s)’ means a complete set of components necessary for limiting the sound emitted
by a motor vehicle and its exhaust.
2.6. ‘Original exhaust or silencing system’ means a system of the type with which the vehicle is equipped on
acceptance or extension of acceptance. It may be part of the original equipment or a replacement.
2.7. ‘Exhaust or silencing systems of different types’ means exhaust or silencing systems which differ in such
essential respects as:
2.7.1. That their components bear different trade names or marks;
2.7.2. That the characteristics of the materials constituting a component are different or that the components differ in
shape or size;
2.7.3. That the operating principles of at least one component are different;
2.7.4. That their components are assembled differently.
2.8. ‘Exhaust or silencing system component’ means one of the individual constituent parts whose assembly
constitutes the exhaust or silencing system (3).
If the engine is fitted with an intake device (air filter and/or an intake sound absorber essential in order to
ensure conformity with sound level limits), this device shall be considered to be a component of the same
importance as the exhaust system proper, and be included in the list referred to in paragraph 3.2.2 below and
carry the markings prescribed in paragraph 4.1 below.
(1) As defined in the Consolidated Resolution on the Construction of Vehicles (R.E.3), document ECE/TRANS/WP.29/78/Rev.4, para.2.
(2) If the rated maximum net power is reached at several engine speeds, the rated engine speed is used in this Regulation as the highest
engine speed at which the rated maximum net power is reached.
(3) These components are, in particular, the exhaust manifold, the exhaust piping, the expansion chamber, the silencer proper, etc. If the
engine intake is equipped with an air filter and the filter's presence is essential to ensure observance of the prescribed sound-level limits,
the filter must be regarded as a component of the ‘exhaust or silencing system(s)’ and bear the marking prescribed in paragraphs 3.2.2
and 4.1.16.11.2018 EN Official Journal of the European Union L 290/3
2.9. ‘Reference mass’ means the mass of the vehicle ready for normal operation and fitted with the following
equipment:
(a) Full electrical equipment including the lighting and signalling devices supplied by the manufacturer;
(b) All instruments and fittings required by any legislation in respect of which a measurement of the vehicle
dry mass is being made;
(c) Full complement of liquids to ensure the correct functioning of every part of the vehicle and the fuel tank
filled at least to 90 per cent of the capacity specified by the manufacturer;
(d) Auxiliary equipment usually supplied by the manufacturer in addition to that necessary for normal
operation (tool-kit, carrier(s), windscreen(s), protective equipment, etc.);
(e) the mass of the propulsion battery, if applicable.
The symbol m denotes the reference mass expressed in kg.
ref
Notes:
1. In the case of a vehicle which operates on a fuel/oil mixture:
1.1. Where the fuel and oil are premixed, the word ‘fuel’ is interpreted as including such a pre-mixture of fuel
and oil;
1.2. Where the fuel and oil are separately measured, the word ‘fuel’ is interpreted as including only the petrol.
The ‘oil’, in this case, is already included in subparagraph (c) of this paragraph.
2.10. ‘Test mass’ means the reference mass plus the combined mass of the driver and test equipment.
The combined mass of the driver and test equipment used on the vehicle shall not be more than 90 kg nor less
than 70 kg. Weights shall be placed on the vehicle, if the 70 kg minimum is not reached.
The symbol m denotes the test mass expressed in kg.
t
2.11. ‘Maximum vehicle speed’ means the maximum vehicle design speed as measured according to ISO 7116:2011
for L category vehicles and according to ISO 7117:2010 for L and L category vehicles.
2 4 5
The symbol v denotes the maximum vehicle speed expressed in km/h.
max
3. APPLICATION FOR APPROVAL
3.1. The application for approval of a vehicle type with regard to sound shall be submitted by its manufacturer or
by his duly accredited representative.
3.2. It shall be accompanied by the under mentioned documents in triplicate and the following particulars:
3.2.1. A description of the vehicle type with regard to the items mentioned in paragraph 2.2 above. The numbers
and/or symbols identifying the engine type and the vehicle type shall be specified;
3.2.2. A list of the components, duly identified, constituting the exhaust or silencing system;
3.2.3. A drawing of the assembled exhaust or silencing system and an indication of its position on the vehicle;
3.2.4. Detailed drawings of each component to enable it to be easily located and identified, and a specification of the
materials used.
3.3. At the request of the Technical Service conducting approval tests, the vehicle manufacturer shall, in addition,
submit a sample of the exhaust or silencing system.
3.4. A vehicle representative of the vehicle type to be approved shall be submitted to the Technical Service
conducting approval tests.
4. MARKINGS
4.1. The components of the exhaust or silencing system shall bear at least the following identifications marks:
4.1.1. The trade name or mark of the manufacturer of the exhaust or silencing system and of its components;
4.1.2. The trade description given by the manufacturer;
4.1.3. The identifying part numbers;L 290/4 EN Official Journal of the European Union 16.11.2018
4.1.4. For all original silencers, the ‘E’ mark followed by the identification of the country which granted the
component type approval (1).
4.1.5. Any packing of original replacement exhaust or silencing systems shall be marked legibly with the words
‘original part’ and the make and type references integrated together with the ‘E’ mark and also the reference of
the country of origin.
4.1.6. Such markings shall be indelible, clearly legible and also visible, in the position at which it is to be fitted to the
vehicle.
5. APPROVAL
5.1. If the vehicle type submitted for approval pursuant to this Regulation meets the requirements of paragraphs 6
and 7 below, approval of that vehicle type shall be granted.
5.2. An approval number shall be assigned to each type approved. Its first two digits (at present 07 corresponding
to the 07 series of amendments which entered into force on 3 November 2013) shall indicate the series of
amendments incorporating the most recent major technical amendments made to the Regulation at the time of
issue of the approval. The same Contracting Party shall not assign the same number to the same vehicle type
equipped with another type of exhaust or silencing system or to another vehicle type.
5.3. Notice of approval or of extension or refusal of approval of a vehicle type pursuant to this Regulation shall be
communicated to the Parties to the Agreement which apply this Regulation by means of a form conforming to
the model shown in Annex 1 to this Regulation and of drawings of the exhaust or silencing system (supplied
by the applicant for approval) in a format not exceeding A4 (210 × 297 mm), or folded to that format, and on
an appropriate scale.
5.4. There shall be affixed, conspicuously and in a readily accessible place specified on the approval form, to every
vehicle conforming to a vehicle type approved under this Regulation an international approval mark consisting
of:
5.4.1. A circle surrounding the letter ‘E’ followed by the distinguishing number of the country which has granted
approval; (1) and
5.4.2. The number of this Regulation, followed by the letter ‘R’, a dash and the approval number, to the right of the
circle prescribed in paragraph 5.4.1 above.
5.5. If the vehicle conforms to a vehicle type approved, under one or more other Regulations annexed to the 1958
Agreement, in the country which has granted approval under this Regulation, the symbol prescribed in
paragraph 5.4.1 above need not be repeated; in such a case the additional numbers and symbols of all the
Regulations under which approval has been granted in the country which has granted approval under this
Regulation shall be placed in vertical columns to the right of the symbol prescribed in paragraph 5.4.1 above.
5.6. The approval mark shall be clearly legible and be indelible.
5.7. The approval mark shall be placed close to or on the vehicle data plate.
5.8. Annex 2 to this Regulation gives examples of arrangements of approval marks.
6. SPECIFICATIONS
6.1. General specifications
6.1.1. The vehicle, its engine and its exhaust or silencing system shall be so designed, constructed and assembled as to
enable the vehicle, in normal use, despite the vibration to which it may be subjected, to comply with the
provisions of this Regulation.
6.1.2. The exhaust or silencing system shall be so designed, constructed and assembled as to be able to resist the
corrosive action to which it is exposed.
6.1.3. The following information shall be provided on the motor vehicle in an easily accessible but not necessarily
immediately visible location:
(a) The manufacturer's name;
(b) The target engine speed and the final result of the stationary test as defined in paragraph 3.1.4 of Annex 3.
(1) The distinguishing numbers of the Contracting Parties to the 1958 Agreement are reproduced in Annex 3 to the Consolidated
Resolution on the Construction of Vehicles (R.E.3) (ECE/TRANS/WP.29/78/Rev.4).16.11.2018 EN Official Journal of the European Union L 290/5
6.2. Specifications regarding sound levels
6.2.1. Methods of measurement
6.2.1.1. The sound emitted by the vehicle type submitted for approval shall be measured by the method(s) described in
Annex 3 to this Regulation for the vehicle in motion and for the vehicle when stationary (1); in the case of
a vehicle with an electric motor or with an internal combustion engine that does not operate when the vehicle
is stationary, the emitted sound shall only be measured when the vehicle is in motion.
If the vehicle has user selectable software programs or modes which affect the sound emission of the vehicle,
all these modes shall be in compliance with the requirements in this paragraph. Testing shall be based on the
worst case scenario.
For hybrid electric vehicles, the tests shall be performed twice under the following conditions:
(a) Condition A: The batteries shall be at their maximum state of charge; if more than one ‘hybrid mode’ is
available, the most electric hybrid mode shall be selected for the test;
(b) Condition B: The batteries shall be at their minimum state of charge; if more than one ‘hybrid mode’ is
available, the most fuel-consuming hybrid mode shall be selected for the test.
The final result is the highest of the test results for conditions A and B.
6.2.1.2. The value(s) measured in accordance with the provisions of paragraph 6.2.1.1 above shall be entered in the test
report and on a form conforming to the model in Annex 1 to this Regulation.
6.2.1.3. The sound level determined by the method described in paragraph 3.1 of Annex 3 to this Regulation when the
vehicle is in motion shall not exceed the limits prescribed (for new vehicles and new exhaust or silencing
systems) in Annex 4 to this Regulation for the category to which the vehicle belongs.
6.3. Additional requirements
6.3.1. Tampering protection provisions
All exhaust or silencing systems shall be constructed in a way that does not permit removal of baffles, exit-
cones and other parts whose primary function is as part of the silencing/expansion chambers. Where
incorporation of such a part is unavoidable, its method of attachment shall be such that removal is not
facilitated (e.g. with conventional threaded fixings) and shall also be attached such that removal causes
permanent/irrecoverable damage to the assembly.
6.3.2. Multi-mode exhaust or silencing systems
Exhaust or silencing systems with multiple, manually or electronically adjustable, rider selectable operating
modes shall meet all requirements in all operating modes. The reported sound levels shall be those resulting
from the mode with the highest sound levels.
6.3.3. Prohibition of defeat devices
The vehicle manufacturer shall not intentionally alter, adjust or introduce any device or procedure solely for the
purpose of fulfilling the sound emission requirements of this Regulation, which will not be operational during
typical on-road operation.
7. MODIFICATION AND EXTENSION OF APPROVAL OF A VEHICLE TYPE OR A TYPE OF EXHAUST OR SILENCING
SYSTEM(S)
7.1. Every modification of the vehicle type or of the exhaust or silencing system shall be notified to the Type
Approval Authority which approved the vehicle type. The said Authority may then either:
7.1.1. Consider that the modifications made are unlikely to have an appreciable adverse effect; or
7.1.2. Require a further test report from the Technical Service responsible for conducting the tests.
7.2. Confirmation or refusal of approval, specifying the alterations, shall be communicated to the Parties to the
Agreement applying this Regulation in accordance with the procedure specified in paragraph 5.3 above.
(1) A test is made on a stationary vehicle in order to provide a reference value for administrations which use this method to check vehicles in
use.L 290/6 EN Official Journal of the European Union 16.11.2018
7.3. The Type Approval Authority issuing the extension of approval shall assign a series number for such an
extension and inform thereof the other Contracting Parties to the 1958 Agreement applying this Regulation by
means of a communication form conforming to the model given in Annex 1 to this Regulation.
8. CONFORMITY OF PRODUCTION
The conformity of production procedures shall comply with those set out in the Agreement, Appendix 2
(E/ECE/324-E/ECE/TRANS/505/Rev.2), with the following requirements:
8.1. Every vehicle bearing an approval mark as prescribed under this Regulation shall conform to the vehicle type
approved, be fitted with the exhaust or silencing system(s) with which it was approved and satisfy the
requirements of paragraph 6 above.
8.2. In order to verify conformity as prescribed in paragraph 8.1 above, a vehicle, bearing the approval mark
required by this Regulation, shall be taken from the series. Production shall be deemed to conform to the
requirements of this Regulation if the levels measured using the method described in Annex 3 do not exceed
by more than 3 dB(A) the value measured on acceptance, nor by more than 1 dB(A) the limits prescribed in
paragraph 6.2.1.3 above.
9. PENALTIES FOR NON-CONFORMITY OF PRODUCTION
9.1. The approval granted in respect of a vehicle type pursuant to this Regulation may be withdrawn if the
requirements laid down in paragraph 8 above are not complied with, or if the vehicle fails to pass the tests
provided for in paragraph 8.2 above.
9.2. If a Party to the Agreement which applies this Regulation withdraws an approval it has previously granted, it
shall forthwith so notify the other Contracting Parties applying this Regulation by means of a communication
form conforming to the model given in Annex 1 to this Regulation.
10. PRODUCTION DEFINITIVELY DISCONTINUED
If the holder of the approval completely ceases to manufacture a vehicle or an exhaust or silencing system
approved in accordance with this Regulation, he shall so inform the Type Approval Authority which had
granted the approval. Upon receiving the relevant communication, that Authority shall inform thereof the
other Parties to the Agreement applying this Regulation by means of a communication form conforming to the
model given in Annex 1 to this Regulation.
11. TRANSITIONAL PROVISIONS
11.1. As from the official date of entry into force of the 07 series of amendments, no Contracting Party applying this
Regulation shall refuse to grant or refuse to accept type approvals under this Regulation as amended by the
07 series of amendments.
11.2. As from 24 months after the date of entry into force of the 07 series of amendments, Contracting Parties
applying this Regulation shall grant type approvals only if the vehicle type to be approved meets the
requirements of this Regulation as amended by the 07 series of amendments.
11.3. Contracting Parties applying this Regulation shall not refuse to grant extensions of type approvals for existing
types which have been granted according to the preceding series of amendments to this Regulation.
11.4. Until 24 months after the date of entry into force of the 07 series of amendments to this Regulation, no
Contracting Party applying this Regulation shall refuse national or regional type approval of a vehicle type-
approved to the preceding series of amendments to this Regulation.
11.5. As from 24 months after the date of entry into force of the 07 series of amendments to this Regulation,
Contracting Parties applying this Regulation shall not be obliged to accept, for the purpose of national or
regional type approval, a vehicle type approved to the preceding series of amendments to this Regulation.
11.6. Notwithstanding the transitional provisions above, Contracting Parties whose application of this Regulation
comes into force after the date of entry into force of the most recent series of amendments are not obliged to
accept type approvals which were granted in accordance with any of the preceding series of amendments to
this Regulation and are only obliged to accept type approval granted in accordance with the 07 series
amendments.16.11.2018 EN Official Journal of the European Union L 290/7
11.7. As from the official date of entry into force of Supplement 1 to the 07 series of amendments, no Contracting
Party applying this Regulation shall refuse to grant or refuse to accept type approval according to
Supplement 1 to 07 series of amendments to the Regulation.
11.8. As from 60 months after the date of entry into force of Supplement 1 to the 07 series of amendments to this
Regulation, Contracting Parties applying this Regulation shall grant type approvals only if the vehicle type to be
approved meets the requirements of this Regulation as amended by Supplement 1 to the 07 series of
amendments to this Regulation.
12. NAMES AND ADDRESSES OF TECHNICAL SERVICES RESPONSIBLE FOR CONDUCTING APPROVAL TESTS, AND OF TYPE
APPROVAL AUTHORITIES
The Parties to the Agreement which apply this Regulation shall communicate to the United Nations Secretariat
the names and addresses of the Technical Services responsible for conducting approval tests and of the Type
Approval Authorities which grant approval and to which forms certifying approval or extension or refusal or
withdrawal of approval or production definitively discontinued, issued in other countries, are to be sent.L 290/8 EN Official Journal of the European Union 16.11.2018
ANNEX 116.11.2018 EN Official Journal of the European Union L 290/9L 290/10 EN Official Journal of the European Union 16.11.2018
ANNEX 2
ARRANGEMENTS OF THE APPROVAL MARK
Model A
(See paragraph 5.4 of this Regulation)
a = 8 mm min
The above approval mark affixed to a vehicle shows that the vehicle type concerned has, with regard to its sound
emission, been approved in the Netherlands (E 4) pursuant to Regulation No 9 under approval No 072439. The
approval number indicates that the approval was granted according to the requirements of Regulation No 9 as amended
by the 07 series of amendments.
Model B
(See paragraph 5.5 of this Regulation)
a = 8 mm min
The above approval mark affixed to a vehicle shows that the vehicle type concerned has been approved in the
Netherlands (E 4) pursuant to Regulations Nos 9 and 33 (1). The approval numbers indicate that, at the date when the
respective approvals were given, Regulation No 9 included the 07 series of amendments and Regulation No 33 was still
in its original form.
(1) The second number is given merely as an example.16.11.2018 EN Official Journal of the European Union L 290/11
ANNEX 3
METHODS AND INSTRUMENTS FOR MEASURING THE SOUND EMITTED BY L, L AND L CATEGORY
2 4 5
VEHICLES
1. MEASURING INSTRUMENTS
1.1. General
The apparatus used for measuring the sound pressure level shall be a sound level meter or equivalent
measuring system meeting the requirements of Class 1 instruments (inclusive of the recommended
windscreen, if used). These requirements are described in IEC 61672-1:2013. Measurements shall be carried
out using the time weighting ‘F’ of the acoustic measuring instrument and the ‘A’ frequency weighting curve
also described in IEC 61672-1:2013. When using a system that includes periodic monitoring of the
A-weighted sound pressure level, a reading should be made at a time interval not greater than 30 ms. The
instruments shall be maintained and calibrated in accordance with the instructions of the instrument
manufacturer.
1.2. Calibration
At the beginning and at the end of every measurement session, the entire acoustic measuring system shall be
checked by means of a sound calibrator that fulfils the requirements of Class 1 sound calibrators according to
IEC 60942:2003. Without any further adjustment, the difference between the readings shall be less than or
equal to 0,5 dB(A). If this value is exceeded, the results of the measurements obtained after the previous
satisfactory check shall be discarded.
1.3. Compliance with requirements
Compliance of the sound calibrator with the requirements of IEC 60942:2003 shall be verified once a year.
Compliance of the instrumentation system with the requirements of IEC 61672-1:2013 shall be verified at
least every 2 years. All compliance testing shall be conducted by a laboratory which is authorised to perform
calibrations traceable to the appropriate standards.
1.4. Instrumentation for speed measurements
The rotational speed of the engine shall be measured with an instrument meeting specification limits of at
least ± 2 per cent or better at the engine speeds required for the measurements being performed.
The road speed of the vehicle shall be measured with instruments meeting specification limits of at
least ± 0,5 km/h when using continuous measuring devices. If testing uses independent measurements of
vehicle speed, this instrumentation shall meet specification limits of at least ± 0,2 km/h (1).
1.5. Meteorological instrumentation
The meteorological instrumentation used to monitor the environmental conditions during the test shall meet
the following specifications:
± 1 °C or less for a temperature measuring device;
± 1,0 m/s for a wind speed measuring device;
± 5 hPa for a barometric pressure measuring device;
± 5 per cent for a relative humidity measuring device.
2. CONDITIONS OF MEASUREMENT
2.1. Test site, weather conditions and background noise level correction
2.1.1. Test site
The test site shall consist of a central acceleration track surrounded by a substantially level test area. The test
track shall be level; the track surface shall be dry and so designed that tyre sound remains low.
On the test site, free sound field conditions shall be maintained to within ± 1 dB between the sound source
placed in the middle of the acceleration section and the microphone. This condition shall be deemed to be
(1) Independent measurements of speed are when two or more separate devices will determine the values of v and v . A continuous
AA′ BB′
measuring device such as radar will determine all required speed information with one device.L 290/12 EN Official Journal of the European Union 16.11.2018
met if there are no large sound-reflecting objects such as fences, rocks, bridges or buildings within 50 m of
the centre of the acceleration section. The surface of the test track shall conform to the requirements of
Annex 5 to this Regulation.
No obstacle likely to affect the sound field shall be close to the microphone and no one shall come between
the microphone and the sound source. The observer taking the measurements shall take up position so as to
avoid influencing the metre readings.
The surface of the test track shall conform to the requirements of Annex 5 to this Regulation or to
ISO10844:2014. After the end of the period indicated in paragraph 11.8 of this Regulation only ISO
10844:2014 shall be used as reference.
2.1.2. Weather conditions and background noise correction
Measurements shall not be made in poor weather conditions. The tests shall not be carried out if the wind
speed, including gusts, exceeds 5 m/s during the sound-measurement interval.
For measurement purposes, the weighted sound level (A) of sound sources other than on the test vehicle and
the sound level produced by the effect of the wind shall be at least 10 dB(A) below the sound level produced
by the vehicle. The microphone may be fitted with a suitable wind guard, provided that its influence on the
sensitivity and directional characteristics of the microphone are taken into account.
If the difference between ambient noise and measured sound levels is between 10 and 15 dB(A), in order to
calculate the test result, the appropriate correction shall be subtracted from the readings on the sound level
meter, as given in Table 1.
Table 1
Correction applied to individual measured test value
Background sound pressure level difference to measured 10 11 12 13 14 ≥ 15
sound pressure level, in dB
Correction, in dB(A) 0,5 0,4 0,3 0,2 0,1 0,0
2.2. Condition of the vehicle
2.2.1. General conditions
The vehicle shall be supplied as specified by the vehicle manufacturer.
Before the measurements are started, the vehicle shall be brought to its normal operating conditions as
regards:
— Temperatures;
— Tuning;
— Fuel;
— Sparking plugs, carburettor(s), etc., (as appropriate).
If the vehicle is fitted with fans with an automatic actuating mechanism, this system shall not be interfered
with during the sound measurements.
If the vehicle is equipped with devices which are not necessary for its propulsion, but which are used whilst
the vehicle is in normal service on the road, those devices shall be in operation in accordance with the specifi
cations of the manufacturer.
For vehicles having more than one driven wheel, only the drive provided for normal road operation may be
used. If the vehicle is fitted with a trailer or a semi-trailer, this shall be removed for the purposes of the test.
2.2.2. Test mass of the vehicle
The vehicle shall be tested with its test mass as defined in paragraph 2.10 of this Regulation.
2.2.3. Tyre selection and condition
The tyres shall be appropriate for the vehicle and shall be inflated to the pressure recommended by the
vehicle manufacturer for the test mass of the vehicle.
The tyres shall be selected by the vehicle manufacturer, and correspond to one of the tyre sizes and types
designated for the vehicle by the vehicle manufacturer. The minimum tread depth shall be at least 80 per cent
of the full tread depth.16.11.2018 EN Official Journal of the European Union L 290/13
3. METHODS OF MEASUREMENT
3.1. Measurement of the sound emission of the vehicles in motion
3.1.1. Test arrangement and microphone positions
3.1.1.1. The test arrangement is shown in Figure 1.
Two lines, AA′ and BB′, parallel to the microphone line PP′ and situated respectively 10 m forward and
10 m rearward of that line shall be marked out on the test track.
3.1.1.2. The distance of the microphone positions from the line CC′, on the microphone line PP′, perpendicular to
the reference line CC′ on the test track (see Figure 1), shall be 7,5 ± 0,05 m.
The microphones shall be located 1,2 ± 0,02 m above the ground level. The reference direction for free-field
conditions (see IEC 61672-1:2013) shall be horizontal and directed perpendicularly towards the path of the
vehicle line CC′.
3.1.2. Acceleration test execution, approach vehicle speed and gear use
3.1.2.1. Acceleration test execution
The vehicle shall approach line AA′ at an initial steady vehicle speed v as specified below. When the front
AA′
of the vehicle reaches line AA′ the accelerator handle shall be fully opened as quickly as practically possible
and kept in that position until the rear of the vehicle reaches the line BB′; the accelerator handle shall then be
returned as quickly as possible to the idle position. The vehicle speed achieved, when the rear of the vehicle
reaches the line BB′ is called v .
BB′
The engine speeds corresponding to v and v in a specific test condition are called n and n .
AA′ BB′ AA′ BB′
In the case of articulated vehicles consisting of two non-separable units regarded as a single vehicle, the semi-
trailer shall be disregarded in determining when line BB′ is crossed.
For all measurements, the vehicle shall be driven in a straight line along the test track in such a way that the
track of the median longitudinal plane of the vehicle is as close as possible to the line CC′.
Figure 1
Measuring positions for vehicles in motionL 290/14 EN Official Journal of the European Union 16.11.2018
3.1.2.2. Determination of the approach vehicle speed and the gear use
3.1.2.2.1. Vehicle with no gearbox
The vehicle shall approach line AA′ at a steady vehicle speed v corresponding either, in terms of engine
AA′
speed, (min– 1) to 75 per cent of the rated engine speed as defined in paragraph 2.4 of this Regulation, or to
75 per cent of the maximum engine speed permitted by the governor, or to 50 km/h, whichever is the
lowest.
3.1.2.2.2. Vehicles with manual transmissions, automatic transmissions, or transmissions with continuously variable
transmission ratios (CVT's) tested with locked gears
If the vehicle is fitted with a dual mode transmission (e.g. low and high), the mode for normal on-road
operation shall be selected.
If the vehicle is fitted with a gearbox with two or three or four forward gears or the same number of lockable
gears in automatic transmission or in CVT, the second gear shall be used. If the gearbox has more than four
forward gears or the same number of lockable gears in automatic transmission or in CVT, the third gear shall
be used.
The vehicle shall approach line AA′ at a steady vehicle speed v corresponding either, in terms of engine
AA′
speed, to 75 per cent of the rated engine speed as defined in paragraph 2.4 of this Regulation or to 75 per
cent of the maximum engine speed permitted by the governor, or to 50 km/h, whichever is the lowest.
If, by following the above procedure, the engine speed n , achieved when the rear of the vehicle passes the
BB′
line BB′, exceeds the rated engine speed as defined in paragraph 2.4 of this Regulation, the first higher gear
(or locked gear) which ensures that the rated engine speed is no longer exceeded up to the line BB′ of the
measurement area should be used instead of the second or third gear.
Auxiliary step-up ratios (‘overdrive’) shall not be engaged.
3.1.2.2.3. Vehicles with automatic transmissions, adaptive transmissions or transmissions with variable transmission
ratios tested with non-locked gears
The gear selector position for full automatic operation shall be used.
Where several full automatic operation modes are available (e.g. economic, sporty), that mode shall be
selected which results in the highest average acceleration of the vehicle between lines AA′ and BB′.
The test may then include a gear change to a lower gear and a higher acceleration. A gear change to a higher
gear and a lower acceleration is not allowed. In any case, a gear change to a gear which is typically not used
at the specified condition in urban traffic shall be avoided.
Therefore, it is permitted to establish and use electronic or mechanical devices, including alternative gear
selector positions, to prevent a downshift to a gear which is typically not used at the specified test condition
in urban traffic. The functionality of the devices shall be described in the communication form.
The vehicle shall approach the line AA′ at a steady vehicle speed v of 50 km/h or at 75 per cent of its
AA′
maximum vehicle speed as defined in paragraph 2.11 of this Regulation, whichever is the lower.
3.1.3. Sound level determination
The maximum sound level recorded at each side of the vehicle shall be reduced by 1 dB(A) to account for
measurement inaccuracy and mathematically rounded to the nearest first decimal place (e.g. 78,45 shall be
noted as to 78,5 while 78,44 shall be noted as to 78,4). These values constitute the results of the
measurement.
The measurement will be invalid if an abnormal discrepancy is recorded between the peak value and the
general sound level.
At least two measurements shall be made on each side of the vehicle.
The measurements shall be considered valid if the difference between the results of the two consecutive
measurements on the same side of the vehicle is not more than 2 dB(A).
Preliminary measurements may be made for adjustment purposes, but shall be disregarded for the determina
tion of the measurement results.16.11.2018 EN Official Journal of the European Union L 290/15
3.1.4. Calculation of the final test result
The final test result is the average of the four test results rounded off to the nearest whole decibel. If the
figure following the decimal point is between 0 and 4, the total is rounded down and if it is between 5 and 9,
it is rounded up.
In case of hybrid electric vehicles, the final result is the highest of the test results for conditions A and B as
described in paragraph 6.2.1.1 of this Regulation.
3.2. Measurement of the sound emitted by stationary vehicles (for testing of vehicles in use)
3.2.1. Sound pressure level close to the outlet(s) of the exhaust system
In addition, so as to facilitate the subsequent testing of vehicles in use, the sound pressure level shall be
measured near the outlet of the exhaust system (silencing system), in conformity with the requirements set
out below, and the result of the measurement shall be included in the test report prepared for the issuance of
the document referred to in Annex 1 to this Regulation.
3.2.2. Measuring instruments
The measurements shall be made using a precision sound level meter in accordance with paragraph 1 of this
annex.
3.2.3. Conditions for measurements
3.2.3.1. Condition of the vehicle
Before the measurements are started, the vehicle engine shall be brought to its normal operating temperature.
If the vehicle is equipped with automatic fans, no adjustment shall be made to them during the measurement
of the sound level.
While measurements are being made, the gear lever shall be in neutral. If the transmission cannot be
disconnected, the drive wheel of the vehicle should be allowed to run under no-load conditions by, for
example, placing the vehicle on a support or on rollers.
3.2.3.2. Test site
Any area not subject to major acoustic perturbations may be used as a test site. Level areas covered with
concrete, asphalt or some other hard material and are highly reflective are suitable; surfaces consisting of
earth which has been tamped down shall not be used. The test site shall have at least the dimensions of
a rectangle the sides of which shall be 3 m from the outline of the vehicle (excluding handlebars). No
significant obstacle such as a person other than the observer and the driver shall be within this rectangle.
The vehicle shall be placed within the above-mentioned rectangle in such a way that the measuring
microphone is at least 1 metre from any stone edging.
3.2.3.3. Miscellaneous
Instrument readings caused by ambient or wind noise shall be at least 10 dB(A) less than the sound level to
be measured. The microphone may be fitted with a suitable wind-guard provided that its effect on
microphone sensitivity is taken into account.
3.2.4. Method of measurement
3.2.4.1. Number of measurements
At least three measurements shall be made at each measurement point. The measurements shall be considered
valid only if the difference between the results of three consecutive measurements is not more than 2 dB(A).
3.2.4.2. Positioning of the microphone (see Figure 2)
The microphone shall be located at a distance of 0,5 ± 0,01 m from the reference point of the exhaust pipe
defined in Figure 3 and at an angle of 45 ± 5° to the vertical plane containing the flow axis of the pipe
termination. The microphone shall be at the height of the reference point, but not less than 0,2 m from the
ground surface. The reference axis of the microphone shall lie in a plane parallel to the ground surface and
shall be directed towards the reference point on the exhaust outlet.L 290/16 EN Official Journal of the European Union 16.11.2018
Figure 2
Microphone positions for the measurement of sound of the stationary vehicle
Figure 3
Reference point
Key:
T = top view
S = side view
1 = reference point
2 = road surface
A = mitered pipe
B = bent down pipe
C = straight pipe
D = vertical pipe
The reference point shall be the highest point satisfying the following conditions:
(a) The reference point shall be at the end of the exhaust pipe,
(b) The reference point shall be on the vertical plane containing the exhaust outlet centre and the flow axis
of the exhaust pipe termination.
If two microphone positions are possible, the location farthest laterally from the vehicle longitudinal
centreline shall be used.
If the flow axis of the exhaust outlet pipe is at 90° ± 5° to the vehicle longitudinal centreline, the microphone
shall be located at the point that is the furthest from the engine.
If a vehicle has two or more exhaust outlets spaced less than 0,3 m apart and connected to a single silencer,
only one measurement shall be made. The microphone shall be located relative to the outlet the farthest from
the vehicle's longitudinal centreline, or, when such outlet does not exist, to the outlet that is highest above the
ground.
For vehicles having an exhaust provided with outlets spaced more than 0,3 m apart, one measurement is
made for each outlet as if it were the only one, and the highest sound pressure level shall be noted.
For the purpose of roadside checking, the reference point may be moved to the outer surface of the vehicle
body.
For vehicles equipped with multiple exhaust outlets, the reported sound pressure level shall be for the outlet
having the highest average sound pressure level.16.11.2018 EN Official Journal of the European Union L 290/17
3.2.4.3. Operating conditions
The engine speed shall be held steady at one of the following values:
50 per cent of n if n exceeds 5 000 min– 1
rated rated
75 per cent of n if n does not exceed 5 000 min– 1
rated rated
Where n is the rated engine speed as defined in paragraph 2.4 of this Regulation.
rated
For a vehicle which cannot reach, in a stationary test, the target engine speed defined above, 95 per cent of
the maximum engine speed reachable in a stationary test shall be used instead as target engine speed.
The engine speed shall be gradually increased from idle to the target engine speed and held constant within
a tolerance band of ± 5 per cent. Then the throttle control shall be rapidly released and the engine speed shall
be returned to idle. The sound pressure level shall be measured during a period consisting of constant engine
speed of at least 1 s and throughout the entire deceleration period. The maximum sound level meter reading
shall be taken as the test value.
A measurement shall be regarded as valid only if the test engine speed did not deviate from the target engine
speed by more than the specified tolerance of ± 5 per cent for at least 1 s.
3.2.4.4. Measurements shall be made at the microphone location(s) prescribed above. The maximum A-weighted
sound pressure level indicated during the test shall be noted, retaining one significant figure behind the
decimal place (e.g. 92,45 shall be noted as to 92,5 while 92,44 shall be noted as to 92,4).
The test shall be repeated until three consecutive measurements that are within 2,0 dB(A) of each other are
obtained at each outlet.
The test result for a given outlet is the arithmetic average of the three valid measurements, mathematically
rounded to the nearest integer value (e.g. 92,5 shall be noted as to 93 while 92,4 shall be noted as to 92).
3.2.4.5. Multi-mode exhaust system
3.2.4.5.1. Vehicles equipped with a multiple mode, manually adjustable exhaust system shall be tested in all modes.
3.2.4.5.2. For vehicles equipped with a multi-mode exhaust system and a manual exhaust mode control the reported
sound pressure level shall be for the mode having the highest average sound pressure level.
4. SOUND FROM THE VEHICLE IN MOTION (DATA REPORTED TO FACILITATE TESTING OF THE VEHICLE IN USE).
4.1. A test procedure for in use compliance tests may be defined by a Contracting Party, taking due account of
any differences from the test conditions used at type-approval.
4.2. In order to facilitate in use compliance test of vehicles, the following information relating to the sound-
pressure level measurements carried out in accordance with paragraph 1 of Annex 3 for the vehicle in
motion is referred to as in use compliance reference data:
(a) Gear (i) or, for vehicles tested with non-locked gear ratios, the position of the gear selector chosen for the
test;
(b) The vehicle speed v in km/h at the beginning of the full throttle acceleration test in gear (i); and
AA′
(c) The final test result in dB(A) as determined according to paragraph 3.1.4 of this annex.
4.3. The in use compliance reference data shall be entered in the communication form conforming to Annex 1.
5. ORIGINAL EXHAUST (SILENCING) SYSTEM
5.1. Requirements for silencers containing absorbent fibrous materials
5.1.1. Fibrous absorbent material shall be asbestos-free and may be used in the construction of silencers only if
suitable devices ensure that the fibrous absorbent material is kept in place for the whole time that the silencer
is being used and the exhaust or silencing system meets the requirements of any one of paragraphs 5.1.2,
5.1.3, 5.1.4 or 5.1.5 below.L 290/18 EN Official Journal of the European Union 16.11.2018
5.1.2. After removal of the fibrous material, the sound-level shall conform to the requirements of paragraph 6.2.1.3
of this Regulation.
5.1.3. The fibrous absorbent material may not be placed in those parts of the silencer through which the exhaust
gases pass and shall conform to the following requirements:
5.1.3.1. The material shall be heated at a temperature of 650 ± 5 °C for four hours in a furnace without reduction in
the average length, diameter or bulk density of the fibre;
5.1.3.2. After heating at 650 ± 5 °C for one hour in a furnace, at least 98 per cent of the material shall be retained in
a sieve of nominal aperture size 250 μm conforming to ISO standard 3310/1:2000 when tested in
accordance with ISO standard 2559:2011.
5.1.3.3. The loss in weight of the material shall not exceed 10,5 per cent after soaking for 24 h at 90 ± 5 °C in
a synthetic condensate of the following composition:
1 N hydrobromic acid (HBr) 10 ml
1 N sulphuric acid (H SO ) 10 ml
2 4
Distilled water to make up to 1 000 ml
Note: The material must be washed in distilled water and dried for one hour at 105 °C before weighing.
5.1.4. Before the system is tested in accordance with paragraph 3 above, it shall be put into a normal state for road
use by one of the following methods:
5.1.4.1. Conditioning by continuous road operation
5.1.4.1.1. Depending on the engine capacity of the vehicle, the minimum distances to be completed during
conditioning shall be:
Category of vehicle according to cylinder capacity in cm3 Distance (km)
1. ≤ 250 4 000
2. > 250 ≤ 500 6 000
3. > 500 8 000
5.1.4.1.2. 50 per cent ± 10 per cent of this conditioning cycle shall consist of town driving and the remainder of long-
distance runs at high vehicle speed; the continuous road cycle may be replaced by a corresponding test-track
programme;
5.1.4.1.3. The two vehicle speed regimes shall be alternated at least six times;
5.1.4.1.4. The complete test programme shall include a minimum of 10 breaks of at least 3 h duration in order to
reproduce the effects of cooling and condensation.
5.1.4.2. Conditioning by pulsation
5.1.4.2.1. The exhaust system or components thereof shall be fitted to the vehicle or to the engine.
In the former case, the vehicle shall be mounted on a roller dynamometer. In the second case, the engine
shall be mounted on a test bench.
The test apparatus, a detailed diagram of which is shown in Figure 4, shall be fitted at the outlet of the
exhaust system. Any other apparatus providing equivalent results shall be acceptable.16.11.2018 EN Official Journal of the European Union L 290/19
Figure 4
Test apparatus for conditioning by pulsation
1. Inlet flange or sleeve for connection to the rear of the test exhaust system
2. Hand-operated regulating valve.
3. Compensating reservoir with a maximum capacity of 40 1 and a filling time of not less than one second.
4. Pressure switch with an operating range of 5 to 250 kPa.
5. Time delay switch.
6. Pulse counter.
7. Quick-acting valve, such as exhaust brake valve 60 mm in diameter, operated by a pneumatic cylinder
with an output of 120 N at 400 kPa. The response time, both when opening and closing, shall not
exceed 0,5 seconds.
8. Exhaust gas evacuation.
9. Flexible pipe.
10. Pressure gauge.
5.1.4.2.2. The test equipment shall be adjusted so that the flow of exhaust gases is alternately interrupted and restored
2 500 times by a rapid-action valve.
5.1.4.2.3. The valve shall open when the exhaust gas back-pressure, measured at least 100 mm downstream of the
intake flange, reaches a value of between 35 and 40 kPa. Should such a figure be unattainable because of the
engine characteristics, the valve shall open when the gas back-pressure reaches a level equivalent to 90 per
cent of the maximum that can be measured before the engine stops. It shall close when this pressure does not
differ by more than 10 per cent from its stabilised value with the valve open.
5.1.4.2.4. The time-delay switch shall be set for the duration of exhaust gases calculated on the basis of the
requirements of paragraph 5.1.4.2.3 above.
5.1.4.2.5. The engine speed shall be 75 per cent of the rated engine speed as defined in paragraph 2.4 of this
Regulation.
5.1.4.2.6. The power indicated by the dynamometer shall be 50 per cent of the full-throttle power measured at 75 per
cent of the rated engine speed as defined in paragraph 2.4 of this Regulation.
5.1.4.2.7. Any drainage holes shall be closed off during the test.
5.1.4.2.8. The entire test shall be completed within 48 hours. If necessary, a cooling period shall be allowed after each
hour.L 290/20 EN Official Journal of the European Union 16.11.2018
5.1.4.3. Conditioning on a test bench
5.1.4.3.1. The exhaust system shall be fitted to an engine representative of the type fitted to the vehicle for which the
system is designed, and mounted on a test bench.
5.1.4.3.2. Conditioning shall consist of the specified number of test bench cycles for the engine capacity class of
vehicle, for which the exhaust system was designed. The number of cycles for each vehicle class shall be:
Category of vehicle according to cylinder capacity in cm3 Number of cycles
1. ≤ 250 6
2. > 250 ≤ 500 9
3. > 500 12
5.1.4.3.3. Each test-bench cycle shall be followed by a break of at least six hours in order to reproduce the effects of
cooling and condensation.
5.1.4.3.4. Each test-bench cycle shall consist of six phases. The engine conditions for, and the duration of, each phase
shall be:
Duration of phase
Phase Conditions
Engines of less than Engines of 250 cm3
250 cm3 or more
(min) (min)
1 Idling 6 6
2 25 per cent load at 75 per cent of n 40 50
rated
3 50 per cent load at 75 per cent of n 40 50
rated
4 100 per cent load at 75 per cent of n 30 10
rated
5 50 per cent load at 100 per cent of n 12 12
rated
6 25 per cent load at 100 per cent of n 22 22
rated
Total time 2 h 30 min 2 h 30 min
5.1.4.3.5. During this conditioning procedure, at the request of the manufacturer, the engine and the silencer may be
cooled in order that the temperature recorded at a point not more than 100 mm from the exhaust gas outlet
does not exceed that measured when the vehicle is running at 110 km/h or 75 per cent of the rated engine
speed as defined in paragraph 2.4 of this Regulation in top gear. The engine and/or vehicle speeds shall be
determined with a tolerance of ± 3 per cent.
5.1.5. Exhaust gases are not in contact with fibrous materials and fibrous materials are not under the influence of
pressure variations.
5.2. Diagram and markings
5.2.1. The diagram and a dimensioned cross-section of the silencer shall be annexed to the document mentioned in
Annex 1 to this Regulation.
5.2.2. All original silencers shall bear at least the following:
(a) The ‘E’ mark followed by the reference to the country which granted the type-approval;
(b) The vehicle manufacturer's name or trademark; and
(c) The make and identifying part number.
This reference shall be legible, indelible and visible in the position at which it is to be fitted.16.11.2018 EN Official Journal of the European Union L 290/21
5.2.3. Any packaging of original replacements for exhaust or silencing systems shall be marked legibly with the
words ‘original part’ and the make and type reference integrated together with the ‘E’ mark and also the
reference of the country of origin.
5.3. Intake silencers
If the engine intake has to be fitted with an air filter and/or intake silencer in order to comply with the
permissible sound level, the filter and/or silencer shall be regarded as part of the silencer and the
requirements of paragraphs 5.1 and 5.2 above shall also be applicable to them.L 290/22 EN Official Journal of the European Union 16.11.2018
ANNEX 4
MAXIMUM SOUND LEVEL LIMITS (NEW VEHICLES)
Vehicle category Maximum sound level values in dB(A)
L 76
2
L 80
4
L 80
516.11.2018 EN Official Journal of the European Union L 290/23
ANNEX 5
TEST TRACK SPECIFICATIONS (1)
1. INTRODUCTION
This annex describes the specifications relating to the physical characteristics and the laying of the test track.
These specifications based on a special standard (2) describe the required physical characteristics as well as the
test methods for these characteristics.
2. REQUIRED CHARACTERISTICS OF THE SURFACE
A surface is considered to conform to this standard provided that the texture and voids content or sound
absorption coefficient have been measured and found to fulfil all the requirements of paragraphs 2.1 to 2.4
below and provided that the design requirements (paragraph 3.2 below) have been met.
2.1. Residual voids content
The residual voids content, V , of the test track paving mixture shall not exceed 8 per cent. For the
C
measurement procedure, see paragraph 4.1 below.
2.2. Sound absorption coefficient
If the surface fails to conform to the residual voids content requirement, the surface is acceptable only if its
sound absorption coefficient, α ≤ 0,10. For the measurement procedure, see paragraph 4.2 below. The
requirements of paragraph 2.1 above and this paragraph are met also if only sound absorption has been
measured and found to be α ≤ 0,10.
Note: The most relevant characteristic is the sound absorption, although the residual voids content is more
familiar among road constructors. However, sound absorption needs to be measured only if the surface fails to
comply with the voids requirement. This is because the latter is connected with relatively large uncertainties in
terms of both measurements and relevance and some surfaces therefore may be rejected erroneously on the
basis of the voids measurement only.
2.3. Texture depth
The texture depth (TD) measured according to the volumetric method (see paragraph 4.3 below) shall be:
TD ≥ 0,4 mm
2.4. Homogeneity of the surface
Every practical effort shall be made to ensure that the surface is made to be as homogeneous as possible within
the test area. This includes the texture and voids content, but it should also be observed that if the rolling
process results in more effective rolling at some places than at others, the texture may be different and
unevenness causing bumps may also occur.
2.5. Period of testing
In order to check whether the surface continues to conform to the texture and voids content or sound
absorption requirements stipulated in this standard, periodic testing of the surface shall be done at the
following intervals:
(a) For residual voids content or sound absorption:
When the surface is new; if the surface meets the requirements when new, no further periodical testing is
required.
(b) For texture depth (TD):
When the surface is new; when the sound testing starts (Note: Not before four weeks after laying); then
every 12 months.
(1) The specifications for the test site reproduced in this annex are valid until the end of the period indicated in paragraph 11.8 of this
Regulation.
(2) ISO 10844:1994L 290/24 EN Official Journal of the European Union 16.11.2018
3. TEST SURFACE DESIGN
3.1. Area
When designing the test track lay-out it is important to ensure that, as a minimum requirement, the area
traversed by the vehicles running through the test strip is covered with the specified test material with suitable
margins for safe and practical driving. This will require the width of the track to be at least 3 m and the length
of the track to extend beyond lines AA and BB by at least 10 m at either end. Figure 1 shows a plan of
a suitable test site and indicates the minimum area which shall be machine laid and machine compacted with
the specified test surface material. According to Annex 3, paragraph 3.1.1.1, measurements have to be made
on each side of the vehicle. This can be done either by measuring with two microphone locations (one on each
side of the track) and driving in one direction, or measuring with a microphone only on one side of the track
but driving the vehicle in two directions. If the latter method is used, then there are no surface requirements on
that side of the track where there is no microphone.
Figure 1
Minimum requirement for test surface area. The shaded part is called ‘Test Area’
3.2. Design and preparation of the surface
3.2.1. Basic design requirements; the test surface shall meet four design requirements:
3.2.1.1. It shall be a dense asphaltic concrete;
3.2.1.2. The maximum chipping size shall be 8 mm (tolerances allow from 6,3 to 10 mm);
3.2.1.3. The thickness of the wearing course shall be ≥ 30 mm;
3.2.1.4. The binder shall be a straight penetration grade bitumen without modification.
3.2.2. Design guidelines
As a guide to the surface constructor, an aggregate grading curve which will give desired characteristics is
shown in Figure 2. In addition, Table 1 gives some guidelines for obtaining the desired texture and durability.
The grading curve fits the following formula:
P (% passing) = 100 · (d/d )1/2
max
where:
d = square mesh sieve size, in mm
d = 8 mm for the mean curve
max
d = 10 mm for the lower tolerance curve
max
d = 6,3 mm for the upper tolerance curve
max16.11.2018 EN Official Journal of the European Union L 290/25
Figure 2
Grading curve of the aggregate in the asphaltic mix with tolerances
In addition to the above, the following recommendations are given:
(a) The sand fraction (0,063 mm < square mesh sieve size < 2 mm) shall include no more than 55 per cent
natural sand and at least 45 per cent crushed sand;
(b) The base and sub-base shall ensure a good stability and evenness, according to best road construction
practice;
(c) The chippings shall be crushed (100 per cent crushed faces) and of a material with a high resistance to
crushing;
(d) The chippings used in the mix shall be washed;
(e) No extra chippings shall be added onto the surface;
(f) The binder hardness expressed as PEN value shall be 40-60, 60-80 or even 80-100 depending on the
climatic conditions of the country. The rule is that as hard a binder as possible shall be used, provided this
is consistent with common practice;
(g) The temperature of the mix before rolling shall be chosen so as to achieve by subsequent rolling the
required voids content. In order to increase the probability of satisfying the specifications of paragraphs 2.1
to 2.4 above, the compactness shall be studied not only by an appropriate choice of mixing temperature,
but also by an appropriate number of passing and by the choice of compacting vehicle.L 290/26 EN Official Journal of the European Union 16.11.2018
Table 1
Design guidelines
Target values
Tolerances
by total mass of by mass of the
mix aggregate
Mass of stones, square mesh sieve (SM) > 2 mm 47,6 % 50,5 % ± 5
Mass of sand 0,063 < SM < 2 mm 38,0 % 40,2 % ± 5
Mass of filler SM < 0,063 mm 8,8 % 9,3 % ± 2
Mass of binder (bitumen) 5,8 % N.A. ± 0,5
Max. chipping size 8 mm 6,3-10
Binder hardness (see paragraph 3.2.2.(f)) —
Polished stone value (PSV) > 50 —
Compactness, relative to Marshall compactness 98 % —
4. TEST METHOD
4.1. Measurement of the residual voids content
For the purpose of this measurement, cores have to be taken from the track in at least four different positions
which are equally distributed in the test area between lines AA and BB (see Figure 1). In order to avoid in
homogeneity and unevenness in the wheel tracks, cores should not be taken in wheel tracks themselves, but
close to them. Two cores (minimum) should be taken close to the wheel tracks and one core (minimum)
should be taken approximately midway between the wheel tracks and each microphone location.
If there is a suspicion that the condition of homogeneity is not met (see paragraph 2.4 above), cores shall be
taken from more locations within the test area. The residual voids content has to be determined for each core,
then the average value from all cores shall be calculated and compared with the requirement of paragraph 2.1
above. In addition, no single core shall have a voids value which is higher than 10 per cent. The test surface
constructor is reminded of the problem which may arise when the test area is heated by pipes or electrical
wires and cores shall be taken from this area. Such installations shall be carefully planned with respect to future
core drilling locations. It is recommended that a few locations of size approximately 200 × 300 mm should be
left where there are no wires/pipes or where the latter are located deep enough in order not to be damaged by
cores taken from the surface layer.
4.2. Sound absorption coefficient
The sound absorption coefficient (normal incidence) shall be measured by the impedance tube method using
the procedure specified in ISO/DIS 10 534: ‘Acoustics — Determination of sound absorption coefficient and
impedance by a tube method’.
Regarding test specimens, the same requirements shall be followed as regarding the residual voids content (see
paragraph 4.1 above).
The sound absorption shall be measured in the range between 400 Hz and 800 Hz and in the range between
800 Hz and 1 600 Hz (at least at the centre frequencies of third octave bands) and the maximum values shall
be identified for both of these frequency ranges.
Then these values, for all test cores shall be averaged to constitute the final result.
4.3. Volumetric macrotexture measurement
For the purpose of this standard, texture depth measurements shall be made on at least 10 positions evenly
spaced along the wheel tracks of the test strip and the average value taken to compare with the specified
minimum texture depth. For the description of the procedure see standard ISO 10844:1994.16.11.2018 EN Official Journal of the European Union L 290/27
5. STABILITY IN TIME AND MAINTENANCE
5.1. Age influence
In common with any other surfaces, it is expected that the tyre/road sound level measured on the test surface
may increase slightly during the first 6-12 months after construction.
The surface will achieve its required characteristics not earlier than four weeks after construction.
The stability over time is determined mainly by the polishing and compaction by vehicles driving on the
surface. It shall be periodically checked as stated in paragraph 2.5 above.
5.2. Maintenance of the surface
Loose debris or dust which could significantly reduce the effective texture depth shall be removed from the
surface. In countries with winter climates, salt is sometimes used for de-icing. Salt may alter the surface
temporarily or even permanently in such a way as to increase sound, and is therefore not recommended.
5.3. Repaving the test area
If it is necessary to repave the test track, it is usually unnecessary to repave more than the test strip (of 3 m
width in Figure 1) where vehicles are driving, provided the test area outside the strip met the requirement of
residual voids content or sound absorption when it was measured.
6. DOCUMENTATION OF THE TEST SURFACE AND OF TESTS PERFORMED ON IT
6.1. Documentation of the test surface
The following data shall be given in a document describing the test surface:
6.1.1. The location of the test track.
6.1.2. Type of binder, binder hardness, type of aggregate, maximum theoretical density of the concrete (D ), thickness
R
of the wearing course and grading curve determined from cores from the test track.
6.1.3. Method of compaction (e.g. type of roller, roller mass, number of passes).
6.1.4. Temperature of the mix, temperature of the ambient air and wind speed during laying of the surface.
6.1.5. Date when the surface was laid and name of the contractor.
6.1.6. All test results or at least the latest test result, including:
6.1.6.1. The residual voids content of each core;
6.1.6.2. The locations in the test area from where the cores for voids measurements have been taken;
6.1.6.3. The sound absorption coefficient of each core (if measured). Specify the results both for each core and each
frequency range, as well as the overall average;
6.1.6.4. The locations in the test area from where the cores for absorption measurement have been taken;
6.1.6.5. Texture depth, including the number of tests and standard deviation;
6.1.6.6. The institution responsible for the tests according to paragraphs 6.1.6.1 and 6.1.6.2 above and the type of
equipment used;
6.1.6.7. Date of the test(s) and date when the cores were taken from the test track.
6.2. Documentation of vehicle sound tests conducted on the surface
In the document describing the vehicle sound test(s) it should be stated whether all the requirements of this
standard were fulfilled or not. Reference shall be given to a document according to paragraph 6.1 above
describing the results which verify this.