Regulation No 94 of the Economic Commission for Europe of the United Nations (UNECE) — Uniform provisions concerning the approval of vehicles with regard to the protection of the occupants in the event of a frontal collision [2018/178]

8.2.2018 EN Official Journal of the European Union L 35/1 II (Non-legislative acts) ACTS ADOPTED BY BODIES CREATED BY INTERNATIONAL AGREEMENTS Only the original UN/ECE texts have legal effect under international public law. The status and date of entry into force of this Regulation should be checked in the latest version of the UN/ECE status document TRANS/WP.29/343, available at: http://www.unece.org/trans/main/wp29/wp29wgs/wp29gen/wp29fdocstts.html Regulation No 94 of the Economic Commission for Europe of the United Nations (UNECE) — Uniform provisions concerning the approval of vehicles with regard to the protection of the occupants in the event of a frontal collision [2018/178] Incorporating all valid text up to: 03 series of amendments to the Regulation — Date of entry into force: 18 June 2016 CONTENTS REGULATION 1. Scope 2. Definitions 3. Application for approval 4. Approval 5. Specifications 6. Instructions for users of vehicles equipped with airbags 7. Modification and extension of approval of the vehicle type 8. Conformity of production 9. Penalties for non-conformity of production 10. Production definitively discontinued 11. Transitional provisions 12. Names and addresses of Technical Services responsible for conducting approval tests, and of Type Approval Authorities ANNEXES 1. Communication 2. Arrangements of approval marks 3. Test procedure 4. Head Performance Criterion (HPC) and 3 ms head acceleration performance criteria 5. Arrangement and installation of dummies and adjustment of restraint systemsL 35/2 EN Official Journal of the European Union 8.2.2018 6. Procedure for determining the ‘H’ point and the actual torso angle for seating positions in motor vehicles Appendix 1 — Description of the three dimensional ‘H’ point machine (3-D H machine) Appendix 2 — Three-dimensional reference system Appendix 3 — Reference data concerning seating positions 7. Test procedure with trolley Appendix — Equivalence curve — tolerance band for curve ΔV = f(t) 8. Technique of measurement in measurement tests: Instrumentation 9. Definition of deformable barrier 10. Certification procedure for the dummy lower leg and foot 11. Test Procedures for the protection of the occupants of vehicles operating on electrical power from high voltage and electrolyte spillage Appendix — Jointed test finger (degree IPXXB) 1. SCOPE This Regulation applies to vehicles of category M (1) of a total permissible mass not exceeding 2,5 tonnes; 1 other vehicles may be approved at the request of the manufacturer. 2. DEFINITIONS For the purpose of this Regulation: 2.1. ‘Protective system’ means interior fittings and devices intended to restrain the occupants and contribute towards ensuring compliance with the requirements set out in paragraph 5 below. 2.2. ‘Type of protective system’ means a category of protective devices which do not differ in such essential respects as: Their technology; Their geometry; Their constituent materials. 2.3. ‘Vehicle width’ means the distance between two planes parallel to the longitudinal median plane (of the vehicle) and touching the vehicle on either side of the said plane but excluding the external devices for indirect vision, side marker lamps, tyre pressure indicators, direction indicator lamps, position lamps, flexible mud-guards and the deflected part of the tyre side-walls immediately above the point of contact with the ground. 2.4. ‘Overlap’ means the percentage of the vehicle width directly in line with the barrier face. 2.5. ‘Deformable barrier face’ means a crushable section mounted on the front of a rigid block. 2.6. ‘Vehicle type’ means a category of power-driven vehicles which do not differ in such essential respects as: 2.6.1. The length and width of the vehicle, in so far as they have a negative effect on the results of the impact test prescribed in this Regulation; 2.6.2. The structure, dimensions, lines and materials of the part of the vehicle forward of the transverse plane through the ‘R’ point of the driver's seat, in so far as they have a negative effect on the results of the impact test prescribed in this Regulation; (1) As defined in the Consolidated Resolution on the Construction of Vehicles (R.E.3.), document ECE/TRANS/WP.29/78/Rev.2, paragraph 2.8.2.2018 EN Official Journal of the European Union L 35/3 2.6.3. The lines and inside dimensions of the passenger compartment and the type of protective system, in so far as they have a negative effect on the results of the impact test prescribed in this Regulation; 2.6.4. The siting (front, rear or centre) and the orientation (transversal or longitudinal) of the engine, in so far as they have a negative effect on the result of the impact test procedure as prescribed in this Regulation; 2.6.5. The unladen mass, in so far as there is a negative effect on the result of the impact test prescribed in this Regulation; 2.6.6. The optional arrangements or fittings provided by the manufacturer, in so far as they have a negative effect on the result of the impact test prescribed in this Regulation; 2.6.7. The locations of the REESS, in so far as they have a negative effect on the result of the impact test prescribed in this Regulation. 2.7. Passenger compartment 2.7.1. ‘Passenger compartment with regard to occupant protection’ means the space for occupant accommodation, bounded by the roof, floor, side walls, doors, outside glazing and front bulkhead and the plane of the rear compartment bulkhead or the plane of the rear-seat back support; 2.7.2. ‘Passenger compartment for electric safety assessment’ means the space for occupant accommodation, bounded by the roof, floor, side walls, doors, outside glazing, front bulkhead and rear bulkhead, or rear gate, as well as by the electrical protection barriers and enclosures provided for protecting the occupants from direct contact with high voltage live parts. 2.8. ‘R point’ means a reference point defined for each seat by the manufacturer in relation to the vehicle's structure, as indicated in Annex 6. 2.9. ‘H point’ means a reference point determined for each seat by the testing service responsible for approval, in accordance with the procedure described in Annex 6. 2.10. ‘Unladen kerb mass’ means the mass of the vehicle in running order, unoccupied and unladen but complete with fuel, coolant, lubricant, tools and a spare wheel (if these are provided as standard equipment by the vehicle manufacturer). 2.11. ‘Airbag’ means a device installed to supplement safety belts and restraint systems in power-driven vehicles, i.e. systems which, in the event of a severe impact affecting the vehicle, automatically deploy a flexible structure intended to limit, by compression of the gas contained within it, the gravity of the contacts of one or more parts of the body of an occupant of the vehicle with the interior of the passenger compartment. 2.12. ‘Passenger airbag’ means an airbag assembly intended to protect occupant(s) in seats other than the driver's in the event of a frontal collision. 2.13. ‘High voltage’ means the classification of an electric component or circuit, if its working voltage is > 60 V and ≤ 1 500 V direct current (DC) or > 30 V and ≤ 1 000 V alternating current (AC) root-mean-square (rms). 2.14. ‘Rechargeable Electrical Energy Storage System (REESS)’ means the rechargeable energy storage system which provides electrical energy for propulsion. 2.15. ‘Electrical protection barrier’ means the part providing protection against any direct contact to the high voltage live parts. 2.16. ‘Electrical power train’ means the electrical circuit which includes the traction motor(s), and may also include the REESS, the electrical energy conversion system, the electronic converters, the associated wiring harness and connectors, and the coupling system for charging the REESS. 2.17. ‘Live parts’ means conductive part(s) intended to be electrically energized in normal use.L 35/4 EN Official Journal of the European Union 8.2.2018 2.18. ‘Exposed conductive part’ means the conductive part which can be touched under the provisions of the protection degree IPXXB and which becomes electrically energized under isolation failure conditions. This includes parts under a cover that can be removed without using tools. 2.19. ‘Direct contact’ means the contact of persons with high voltage live parts. 2.20. ‘Indirect contact’ means the contact of persons with exposed conductive parts. 2.21. ‘Protection degree IPXXB’ means protection from contact with high voltage live parts provided by either an electrical protection barrier or an enclosure and tested using a Jointed Test Finger (degree IPXXB) as described in paragraph 4 of Annex 11, 2.22. ‘Working voltage’ means the highest value of an electrical circuit voltage root-mean-square (rms), specified by the manufacturer, which may occur between any conductive parts in open circuit conditions or under normal operating conditions. If the electrical circuit is divided by galvanic isolation, the working voltage is defined for each divided circuit, respectively. 2.23. ‘Coupling system for charging the rechargeable Electrical Energy Storage System (REESS)’ means the electrical circuit used for charging the REESS from an external electrical power supply including the vehicle inlet. 2.24. ‘Electrical chassis’ means a set made of conductive parts electrically linked together, whose electrical potential is taken as reference. 2.25. ‘Electrical circuit’ means an assembly of connected high voltage live parts which is designed to be electrically energized in normal operation. 2.26. ‘Electrical energy conversion system’ means a system (e.g. fuel cell) that generates and provides electrical energy for electrical propulsion. 2.27. ‘Electronic converter’ means a device capable of controlling and/or converting electrical power for electrical propulsion. 2.28. ‘Enclosure’ means the part enclosing the internal units and providing protection against any direct contact. 2.29. ‘High Voltage Bus’ means the electrical circuit, including the coupling system for charging the REESS that operates on a high voltage. 2.30. ‘Solid insulator’ means the insulating coating of wiring harnesses, provided in order to cover and prevent the high voltage live parts from any direct contact. This includes covers for insulating the high voltage live parts of connectors; and varnish or paint for the purpose of insulation. 2.31. ‘Automatic disconnect’ means a device that when triggered, galvanically separates the electrical energy sources from the rest of the high voltage circuit of the electrical power train. 2.32. ‘Open type traction battery’ means a type of battery requiring liquid and generating hydrogen gas released to the atmosphere. 2.33. ‘Automatically activated door locking system’ means a system that locks the doors automatically at a pre-set speed or under any other condition as defined by the manufacturer. 3. APPLICATION FOR APPROVAL 3.1. The application for approval of a vehicle type with regard to the protection of the occupants of the front seats in the event of a frontal collision (offset deformable barrier test) shall be submitted by the vehicle manufacturer or by his duly accredited representative. 3.2. It shall be accompanied by the undermentioned documents in triplicate and following particulars: 3.2.1. A detailed description of the vehicle type with respect to its structure, dimensions, lines and constituent materials; 3.2.2. Photographs, and/or diagrams and drawings of the vehicle showing the vehicle type in front, side and rear elevation and design details of the forward part of the structure;8.2.2018 EN Official Journal of the European Union L 35/5 3.2.3. Particulars of the vehicle's unladen kerb mass; 3.2.4. The lines and inside dimensions of the passenger compartment; 3.2.5. A description of the interior fittings and protective systems installed in the vehicle; 3.2.6. A general description of the electrical power source type, location and the electrical power train (e.g. hybrid, electric). 3.3. The applicant for approval shall be entitled to present any data and results of tests carried out which make it possible to establish that compliance with the requirements can be achieved with a sufficient degree of confidence. 3.4. A vehicle which is representative of the type to be approved shall be submitted to the Technical Service responsible for conducting the approval tests. 3.4.1. A vehicle not comprising all the components proper to the type may be accepted for test provided that it can be shown that the absence of the components omitted has no detrimental effect on the results of the test in so far as the requirements of this Regulation are concerned. 3.4.2. It shall be the responsibility of the applicant for approval to show that the application of paragraph 3.4.1 above is compatible with compliance with the requirements of this Regulation. 4. APPROVAL 4.1. If the vehicle type submitted for approval pursuant to this Regulation meets the requirements of this Regulation, approval of that vehicle type shall be granted. 4.1.1. The Technical Service appointed in accordance with paragraph 12 below shall check whether the required conditions have been satisfied. 4.1.2. In case of doubt, account shall be taken, when verifying the conformity of the vehicle to the requirements of this Regulation, of any data or test results provided by the manufacturer which can be taken into con­ sideration in validating the approval test carried out by the Technical Service. 4.2. An approval number shall be assigned to each type approved. Its first two digits (at present 03 corresponding to the 03 series of amendments) shall indicate the series of amendments incorporating the most recent major technical amendments made to the Regulation at the time of issue of the approval. The same Contracting Party may not assign the same approval number to another vehicle type. 4.3. Notice of approval or of refusal of approval of a vehicle type pursuant to this Regulation shall be communicated to the Parties to the Agreement which apply this Regulation by means of a form conforming to the model in Annex 1 to this Regulation and photographs and/or diagrams and drawings supplied by the applicant for approval, in a format not exceeding A4 (210 × 297 mm) or folded to that format and on an appropriate scale. 4.4. There shall be affixed, conspicuously and in a readily accessible place specified on the approval form, to every vehicle conforming to a vehicle type approved under this Regulation, an international approval mark consisting of: 4.4.1. A circle surrounding the letter ‘E’ followed by the distinguishing number of the country which has granted approval (1); 4.4.2. The number of this Regulation, followed by the letter ‘R’, a dash and the approval number, to the right of the circle prescribed in paragraph 4.4.1 above. 4.5. If the vehicle conforms to a vehicle type approved, under one or more other Regulations annexed to the Agreement, in the country which has granted approval under this Regulation, the symbol prescribed in paragraph 4.4.1 above need not be repeated; in such a case the Regulation and approval numbers and the additional symbols of all the Regulations under which approval has been granted in the country which has granted approval under this Regulation shall be placed in vertical columns to the right of the symbol prescribed in paragraph 4.4.1. (1) The distinguish numbers of the Contracting Parties to the 1958 Agreement are reproduced in Annex 3 to Consolidated Resolution on the Construction of Vehicles (R.E.3.), document TRANS/WP.29/78/Rev.2/Amend.3.L 35/6 EN Official Journal of the European Union 8.2.2018 4.6. The approval mark shall be clearly legible and be indelible. 4.7. The approval mark shall be placed close to or on the vehicle data plate affixed by the manufacturer. 4.8. Annex 2 to this Regulation gives examples of approval marks. 5. SPECIFICATIONS 5.1. General specifications applicable to all tests 5.1.1. The ‘H’ point for each seat shall be determined in accordance with the procedure described in Annex 6. 5.1.2. When the protective system for the front seating positions includes belts, the belt components shall meet the requirements of Regulation No 16. 5.1.3. Seating positions where a dummy is installed and the protective system includes belts, shall be provided with anchorage points conforming to Regulation No 14. 5.2. Specifications The test of the vehicle carried out in accordance with the method described in Annex 3 shall be considered satisfactory if all the conditions set out in paragraphs 5.2.1 to 5.2.6 below are all satisfied at the same time. Additionally, vehicles equipped with electric power train shall meet the requirements of paragraph 5.2.8 below. This can be met by a separate impact test at the request of the manufacturer and after validation by the Technical Service, provided that the electrical components do not influence the occupant protection performance of the vehicle type as defined in paragraphs 5.2.1 to 5.2.5 of this Regulation. In case of this condition the requirements of paragraph 5.2.8 shall be checked in accordance with the methods set out in Annex 3 to this Regulation, except paragraphs 2, 5 and 6 of Annex 3. But a dummy corresponding to the specifications for Hybrid III (see footnote 1 of Annex 3) fitted with a 45° ankle and meeting the specifi­ cations for its adjustment shall be installed in each of the front outboard seats. 5.2.1. The performance criteria recorded, in accordance with Annex 8, on the dummies in the front outboard seats shall meet the following conditions: 5.2.1.1. The head performance criterion (HPC) shall not exceed 1 000 and the resultant head acceleration shall not exceed 80 g for more than 3 ms. The latter shall be calculated cumulatively, excluding rebound movement of the head; 5.2.1.2. The Injury Criteria for the neck (NIC) shall not exceed the values shown in Figures 1 and 2 (1); Figure 1 Neck tension criterion (1) Until 1 October 1998, the values obtained for the neck shall not be pass/fail criteria for the purposes of granting approval. The results obtained shall be recorded in the test report and be collected by the Type Approval Authority. After this date, the values specified in this paragraph shall apply as pass/fail criteria unless or until alternative values are adopted.8.2.2018 EN Official Journal of the European Union L 35/7 Figure 2 Neck shear criterion 5.2.1.3. The neck bending moment about the y axis shall no exceed 57 Nm in extension (1); 5.2.1.4. The thorax compression criterion (ThCC) shall not exceed 42 mm; 5.2.1.5. The viscous criterion (V * C) for the thorax shall not exceed 1,0 m/s; 5.2.1.6. The femur force criterion (FFC) shall not exceed the force-time performance criterion shown in Figure 3; Figure 3 Femur force criterion 5.2.1.7. The tibia compression force criterion (TCFC) shall not exceed 8 kN; (1) Until 1 October 1998, the values obtained for the neck shall not be pass/fail criteria for the purposes of granting approval. The results obtained shall be recorded in the test report and be collected by the Type Approval Authority. After this date, the values specified in this paragraph shall apply as pass/fail criteria unless or until alternative values are adopted.L 35/8 EN Official Journal of the European Union 8.2.2018 5.2.1.8. The tibia index (TI), measured at the top and bottom of each tibia, shall not exceed 1,3 at either location; 5.2.1.9. The movement of the sliding knee joints shall not exceed 15 mm. 5.2.2. Following the test the residual steering wheel displacement, when measured at the centre of the steering wheel hub, shall not exceed 80 mm in the upwards vertical direction and 100 mm in the rearward horizontal direction. 5.2.3. During the test no door shall open. 5.2.3.1. In the case of automatically activated door locking systems which are installed optionally and/or which can be de-activated by the driver, this requirement shall be verified by using one of the following two test procedures, at the choice of the manufacturer: 5.2.3.1.1. If testing in accordance with Annex 3, paragraph 1.4.3.5.2.1, the manufacturer shall in addition demonstrate to the satisfaction of the Technical Service (e.g. manufacturer's in-house data) that, in the absence of the system or when the system is de-activated, no door will open in case of the impact. 5.2.3.1.2. The test is conducted in accordance with Annex 3, paragraph 1.4.3.5.2.2. 5.2.4. After the impact, the side doors shall be unlocked. 5.2.4.1. In the case of vehicles equipped with an automatically activated door locking system, the doors shall be locked before the moment of impact and be unlocked after the impact. 5.2.4.2. In the case of vehicles equipped with automatically activated door locking systems which are installed optionally and/or which can be de-activated by the driver, this requirement shall be verified by using one of the following two test procedures, at the choice of the manufacturer: 5.2.4.2.1. If testing in accordance with Annex 3, paragraph 1.4.3.5.2.1, the manufacturer shall in addition demonstrate to the satisfaction of the Technical Service (e.g. manufacturer's in-house data) that, in the absence of the system or when the system is de-activated, no locking of the side doors shall occur during the impact. 5.2.4.2.2. The test is conducted in accordance with Annex 3, paragraph 1.4.3.5.2.2. 5.2.5. After the impact, it shall be possible, without the use of tools, except for those necessary to support the weight of the dummy: 5.2.5.1. To open at least one door, if there is one, per row of seats and, where there is no such door, to move the seats or tilt their backrests as necessary to allow the evacuation of all the occupants; this is, however, only applicable to vehicles having a roof of rigid construction; 5.2.5.2. To release the dummies from their restraint system which, if locked, shall be capable of being released by a maximum force of 60 N on the centre of the release control; 5.2.5.3. To remove the dummies from the vehicle without adjustment of the seats. 5.2.6. In the case of a vehicle propelled by liquid fuel, no more than slight leakage of liquid from the fuel feed installation shall occur on collision. 5.2.7. If there is continuous leakage of liquid from the fuel-feed installation after the collision, the rate of leakage shall not exceed 30 g/min; if the liquid from the fuel-feed system mixes with liquids from the other systems and the various liquids cannot easily be separated and identified, all the liquids collected shall be taken into account in evaluating the continuous leakage.8.2.2018 EN Official Journal of the European Union L 35/9 5.2.8. Following the test conducted in accordance with the procedure defined in Annex 3 to this Regulation, the electrical power train operating on high voltage, and the high voltage components and systems, which are galvanically connected to the high voltage bus of the electric power train, shall meet the following requirements: 5.2.8.1. Protection against electrical shock After the impact at least one of the four criteria specified in paragraph 5.2.8.1.1 through paragraph 5.2.8.1.4.2 below shall be met. If the vehicle has an automatic disconnect function, or device(s) that galvanically divide the electric power train circuit during driving condition, at least one of the following criteria shall apply to the disconnected circuit or to each divided circuit individually after the disconnect function is activated. However criteria defined in paragraph 5.2.8.1.4 below shall not apply if more than a single potential of a part of the high voltage bus is not protected under the conditions of protection degree IPXXB. If the test is performed under the condition that part(s) of the high voltage system are not energized, the protection against electrical shock shall be proved by either paragraph 5.2.8.1.3 or 5.2.8.1.4 below for the relevant part(s). For the coupling system for charging the REESS, which is not energized during driving conditions, at least one of the four criteria specified in paragraphs 5.2.8.1.1 to 5.2.8.1.4 below shall be met. 5.2.8.1.1. Absence of high voltage The voltages V, V and V of the high voltage buses shall be equal or less than 30 VAC or 60 VDC as b 1 2 specified in paragraph 2 of Annex 11. 5.2.8.1.2. Low electrical energy The total energy (TE) on the high voltage buses shall be less than 2,0 joules when measured according to the test procedure as specified in paragraph 3 of Annex 11 with the formula (a). Alternatively the total energy (TE) may be calculated by the measured voltage V of the high voltage bus and the capacitance of b the X-capacitors (C) specified by the manufacturer according to formula (b) of paragraph 3 of Annex 11. x The energy stored in the Y-capacitors (TE , TE ) shall also be less than 2,0 joules. This shall be calculated y1 y2 by measuring the voltages V and V of the high voltage buses and the electrical chassis, and the 1 2 capacitance of the Y-capacitors specified by the manufacturer according to formula (c) of paragraph 3 of Annex 11. 5.2.8.1.3. Physical protection For protection against direct contact with high voltage live parts, the protection degree IPXXB shall be provided. In addition, for protection against electrical shock which could arise from indirect contact, the resistance between all exposed conductive parts and the electrical chassis shall be lower than 0,1 ohm when there is current flow of at least 0,2 ampere. This requirement is satisfied if the galvanic connection has been made by welding. 5.2.8.1.4. Isolation resistance The criteria specified in the paragraphs 5.2.8.1.4.1 and 5.2.8.1.4.2 below shall be met. The measurement shall be conducted in accordance with paragraph 5 of Annex 11.L 35/10 EN Official Journal of the European Union 8.2.2018 5.2.8.1.4.1. Electrical power train consisting of separate DC- or AC-buses If the AC high voltage buses and the DC high voltage buses are galvanically isolated from each other, isolation resistance between the high voltage bus and the electrical chassis (R, as defined in paragraph 5 of i Annex 11) shall have a minimum value of 100 Ω/V of the working voltage for DC buses, and a minimum value of 500 Ω/V of the working voltage for AC buses. 5.2.8.1.4.2. Electrical power train consisting of combined DC- and AC-buses If the AC high voltage buses and the DC high voltage buses are galvanically connected isolation resistance between the high voltage bus and the electrical chassis (R, as defined in paragraph 5 of Annex 11) shall i have a minimum value of 500 Ω/V of the working voltage. However, if the protection degree IPXXB is satisfied for all AC high voltage buses or the AC voltage is equal or less than 30 V after the vehicle impact, the isolation resistance between the high voltage bus and the electrical chassis (Ri, as defined in paragraph 5 of Annex 11) shall have a minimum value of 100 Ω/V of the working voltage. 5.2.8.2. Electrolyte spillage In the period from the impact until 30 minutes after no electrolyte from the REESS shall spill into the passenger compartment and no more than 7 per cent of electrolyte shall spill from the REESS except open type traction batteries outside the passenger compartment. For open type traction batteries no more than 7 per cent with a maximum of 5,0 litres shall spill outside the passenger compartment. The manufacturer shall demonstrate compliance in accordance with paragraph 6 of Annex 11. 5.2.8.3. REESS retention REESS located inside the passenger compartment shall remain in the location in which they are installed and REESS components shall remain inside REESS boundaries. No part of any REESS that is located outside the passenger compartment for electric safety assessment shall enter the passenger compartment during or after the impact test. The manufacturer shall demonstrate compliance in accordance with paragraph 7 of Annex 11. 6. INSTRUCTIONS FOR USERS OF VEHICLES EQUIPPED WITH AIRBAGS 6.1. The vehicle shall carry information to the effect that it is equipped with airbags for seats. 6.1.1. For a vehicle fitted with an airbag assembly intended to protect the driver, this information shall consist of the inscription ‘AIRBAG’ located in the interior of the circumference of the steering wheel; this inscription shall be durably affixed and easily visible. 6.1.2. For a vehicle fitted with a passenger airbag intended to protect occupants other than the driver, this information shall consist of the warning label described in paragraph 6.2 below. 6.2. A vehicle fitted with one or more passenger frontal protection airbags shall carry information about the extreme hazard associated with the use of rearward-facing child restraints on seats equipped with airbag assemblies.8.2.2018 EN Official Journal of the European Union L 35/11 6.2.1. As a minimum, this information shall consist of a label containing clear warning pictograms as indicated below: The overall dimensions shall be at least 120 × 60 mm or the equivalent area. The label shown above may be adapted in such a way that the layout differs from the example above; however, the content shall meet the above prescriptions. 6.2.2. In the case of a frontal protection airbag on the front passenger seat, the warning shall be durably affixed to each face of the passenger front sun visor in such a position that at least one warning on the sun visor is visible at all times, irrespective of the position of the sun visor. Alternatively, one warning shall be located on the visible face of the stowed sun visor and a second warning shall be located on the roof behind the visor, so, at least one warning is visible all times. It shall not be possible to easily remove the warning label from the visor and the roof without any obvious and clearly visible damage remaining to the visor or the roof in the interior of the vehicle. If the vehicle does not have a sun visor or roof, the warning label shall be positioned in a location where it is clearly visible at all times. In the case of a frontal protection airbag for other seats in the vehicle, the warning must be directly ahead of the relevant seat, and clearly visible at all times to someone installing a rear-facing child restraint on that seat. The requirements of this paragraph and paragraph 6.2.1 do not apply to those seating positions equipped with a device which automatically deactivates the frontal protection airbag assembly when any rearward facing child restraint is installed.L 35/12 EN Official Journal of the European Union 8.2.2018 6.2.3. Detailed information, making reference to the warning, shall be contained in the owner's manual of the vehicle; as a minimum, the following text in all official languages of the country or countries where the vehicle could reasonably be expected to be registered (e.g. within the territory of the European Union, in Japan, in Russian Federation or in New Zealand, etc.), shall at least include: ‘NEVER use a rearward facing child restraint on a seat protected by an ACTIVE AIRBAG in front of it, DEATH or SERIOUS INJURY to the CHILD can occur’ The text shall be accompanied by an illustration of the warning label as found in the vehicle. The information shall be easily found in the owner's manual (e.g. specific reference to the information printed on the first page, identifying page tab or separate booklet, etc.) The requirements of this paragraph do not apply to vehicles of which all passenger seating positions are equipped with a device which automatically deactivates the frontal protection airbag assembly when any rearward facing child restraint is installed. 7. MODIFICATION AND EXTENSION OF APPROVAL OF THE VEHICLE TYPE 7.1. Any modification affecting the structure, the number of front seats, the interior trim or fittings, or the position of the vehicle controls or of mechanical parts which might affect the energy-absorption capability of the front of the vehicle shall be brought to the notice of the Type Approval Authority granting approval. The Type Approval Authority may then either: 7.1.1. Consider that the modifications made are unlikely to have an appreciable adverse effect and that in any case the vehicle still complies with the requirements; or 7.1.2. Require the Technical Service responsible for conducting the tests to carry out a further test, among those described below, according to the nature of the modifications; 7.1.2.1. Any modification of the vehicle affecting the general form of the structure of the vehicle and/or any increase in mass greater than 8 per cent which in the judgement of the authority would have a marked influence on the results of the tests shall require a repetition of the test as described in Annex 3; 7.1.2.2. If the modifications concern only the interior fittings, if the mass does not increase by more than 8 per cent and if the number of front seats initially provided in the vehicle remains the same, the following shall be carried out: 7.1.2.2.1. A simplified test as provided for in Annex 7 and/or, 7.1.2.2.2. A partial test as defined by the Technical Service in relation to the modifications made. 7.2. Confirmation or refusal of approval, specifying the alterations, shall be communicated by the procedure specified in paragraph 4.3 above to the Parties to the Agreement which apply this Regulation. 7.3. The Type Approval Authority issuing the extension of approval shall assign a series number for such an extension and inform thereof the other Parties to the 1958 Agreement applying this Regulation by means of a communication form conforming to the model in Annex 1 to this Regulation. 8. CONFORMITY OF PRODUCTION The conformity of production procedures shall comply with those set out in the Agreement, Appendix 2 (E/ECE/324-E/ECE/TRANS/505/Rev.2) with the following requirements: 8.1. Every vehicle approved under this Regulation shall conform to the vehicle type approved, as regards features contributing to the protection of the occupants of the vehicle in the event of a frontal collision. 8.2. The holder of the approval shall ensure that for each type of vehicle at least the tests concerning the taking of measurements are carried out. 8.3. The Type Approval Authority which has granted type approval may at any time verify the conformity control methods applied in each production facility. The normal frequency of these verifications shall be once every two years.8.2.2018 EN Official Journal of the European Union L 35/13 9. PENALTIES FOR NON-CONFORMITY OF PRODUCTION 9.1. The approval granted in respect of a vehicle type pursuant to this Regulation may be withdrawn if the requirement laid down in paragraph 7.1 above is not complied with or if the vehicle or vehicles selected have failed to pass the checks prescribed in paragraph 7.2 above. 9.2. If a Contracting Party to the Agreement applying this Regulation withdraws an approval it has previously granted, it shall forthwith so notify the other Contracting Parties applying this Regulation, by means of a communication form conforming to the model in Annex 1 to this Regulation. 10. PRODUCTION DEFINITIVELY DISCONTINUED If the holder of the approval completely ceases to manufacture the type of vehicle approved in accordance with the Regulation, he shall so inform the Type Approval Authority which granted the approval. Upon receiving the relevant communication that Authority shall inform thereof the other Parties to the 1958 Agreement applying this Regulation by means of a communication form conforming to the model in Annex 1 to this Regulation. 11. TRANSITIONAL PROVISIONS 11.1. As from the official date of entry into force of Supplement 4 to the 01 series of amendments, no Contracting Party applying this Regulation shall refuse to grant type approval under this Regulation as amended by Supplement 4 to the 01 series of amendments. 11.2. As from 23 June 2013, Contracting Parties applying this Regulation shall grant type approvals only to those types of vehicles which comply with the requirements of this Regulation as amended by Supplement 4 to the 01 series of amendments. 11.3. As long as there are no requirements in this Regulation with regard to the protection of the occupants by means of a full frontal impact test, Contracting Parties may continue to apply the requirements already in force for that purpose at the time of acceding to this Regulation. 11.4. As from the official date of entry into force of the 02 series of amendments, no Contracting Party applying this Regulation shall refuse to grant type approval under this Regulation as amended by the 02 series of amendments. 11.5. As from 24 months after the official date of entry into force of the 02 series of amendments, Contracting Parties applying this Regulation shall grant type approvals only to those types of vehicle which comply with the requirements of this Regulation as amended by the 02 series of amendments. However, in the case of vehicles having an electrical power train operating on high voltage, an additional period of 12 months is granted provided that the manufacturer demonstrates, to the satisfaction of the Technical Service, that the vehicle provides equivalent levels of safety to those required by this Regulation as amended by the 02 series of amendments. 11.6. Contracting Parties applying this Regulation shall not refuse to grant extensions of approvals issued to the preceding series of amendments to this Regulation, when this extension does not entail any change to the propulsion system of the vehicle. However, as from 48 months after the official date of entry into force of the 02 series of amendments, extensions to approvals issued to the previous series of amendments shall not be granted in respect of vehicles having an electrical power train operating on high voltage. 11.7. Where at the time of entry into force of the 02 series of amendments to this Regulation, national requirements exist to address the safety provisions of vehicles having an electrical power train operating on high voltage, those Contracting Parties applying this Regulation may refuse national approval of such vehicles not meeting the national requirements, unless these vehicles are approved to the 02 series of amendments to this Regulation. 11.8. As from 48 months after the entry into force of the 02 series of amendments to this Regulation, Contracting Parties applying this Regulation may refuse national or regional type approval and may refuse first national or regional registration (first entry into service) of a vehicle having an electrical power train operating on high voltage which does not meet the requirements of the 02 series of amendments to this Regulation.L 35/14 EN Official Journal of the European Union 8.2.2018 11.9. Contracting Parties applying the Regulation shall continue to accept approvals to the 01 series of amendments to this Regulation, for the vehicles which are not affected by the 02 series of amendments. 11.10. Until 18 months after the date of entry into force of the Supplement 4 to the 02 series of amendments to this Regulation, Contracting Parties applying this Regulation can continue to grant type approvals to the 02 series of amendments to this Regulation without taking into account the provisions of Supplement 4. 11.11. As from the official date of entry into force of the 03 series of amendments, no Contracting Party applying this Regulation shall refuse to grant approval under this Regulation as amended by the 03 series of amendments. 11.12. As from 1 September 2018, Contracting Parties applying this Regulation shall grant approvals only to those types of vehicle which comply with the requirements of this Regulation as amended by the 03 series of amendments. 11.13. Contracting Parties applying this Regulation shall not refuse to grant extensions of approvals for existing types which have been granted according to the preceding series of amendments to this Regulation. 11.14. Contracting Parties applying the Regulation shall continue to accept approvals to the 01 series of amendments to the Regulation, granted before 23 June 2013 or 2014, as foreseen in paragraph 11.5 above. 11.15. Contracting Parties applying the Regulation shall continue to accept approvals to the 02 series of amendments to the Regulation, granted before 1 September 2018. 12. NAMES AND ADDRESSES OF TECHNICAL SERVICES RESPONSIBLE FOR CONDUCTING APPROVAL TESTS, AND OF TYPE APPROVAL AUTHORITIES The Contracting Parties to the Agreement applying this Regulation shall communicate to the United Nations secretariat the names and addresses of the Technical Services responsible for conducting approval tests, of manufacturers authorized to carry out tests and of the Type Approval Authorities which grant approval and to which forms certifying approval or refusal or withdrawal of approval, issued in other countries, are to be sent.8.2.2018 EN Official Journal of the European Union L 35/15 ANNEX 1L 35/16 EN Official Journal of the European Union 8.2.20188.2.2018 EN Official Journal of the European Union L 35/17 ANNEX 2 ARRANGEMENTS OF APPROVAL MARKS MODEL A (see paragraph 4.4 of this Regulation) a = 8 mm min. The above approval mark affixed to a vehicle shows that the vehicle type concerned has, with regard to the protection of the occupants in the event of a frontal collision, been approved in the Netherlands (E 4) pursuant to Regulation No 94 under approval number 031424. The approval number indicates that the approval was granted in accordance with the requirements of Regulation No 94 as amended by the 03 series of amendments. MODEL B (see paragraph 4.5 of this Regulation) a = 8 mm min. The above approval mark affixed to a vehicle shows that the vehicle type concerned has been approved in the Netherlands (E 4) pursuant to Regulations Nos 94 and 11 (1). The first two digits of the approval numbers indicate that, at the dates when the respective approvals were granted, Regulation No 94 incorporated the 03 series of amendments and Regulation No 11 incorporated the 03 series of amendments. (1) The latter number is given only as an example.L 35/18 EN Official Journal of the European Union 8.2.2018 ANNEX 3 TEST PROCEDURE 1. INSTALLATION AND PREPARATION OF THE VEHICLE 1.1. Testing ground The test area shall be large enough to accommodate the run-up track, barrier and technical installations necessary for the test. The last part of the track, for at least 5 m before the barrier, shall be horizontal, flat and smooth. 1.2. Barrier The front face of the barrier consists of a deformable structure as defined in Annex 9 of this Regulation. The front face of the deformable structure is perpendicular within ± 1° to the direction of travel of the test vehicle. The barrier is secured to a mass of not less than 7 × 104 kg, the front face of which is vertical within ± 1°. The mass is anchored in the ground or placed on the ground with, if necessary, additional arresting devices to restrict its movement. 1.3. Orientation of the barrier The orientation of the barrier is such that the first contact of the vehicle with the barrier is on the steering- column side. Where there is a choice between carrying out the test with a right-hand or left-hand drive vehicle, the test shall be carried out with the less favourable hand of drive as determined by the Technical Service responsible for the tests. 1.3.1. Alignment of the vehicle to the barrier The vehicle shall overlap the barrier face by 40 per cent ± 20 mm. 1.4. State of vehicle 1.4.1. General specification The test vehicle shall be representative of the series production, shall include all the equipment normally fitted and shall be in normal running order. Some components may be replaced by equivalent masses where this substitution clearly has no noticeable effect on the results measured under paragraph 6. It shall be allowed by agreement between manufacturer and Technical Service to modify the fuel system so that an appropriate amount of fuel can be used to run the engine or the electrical energy conversion system. 1.4.2. Mass of vehicle 1.4.2.1. For the test, the mass of the vehicle submitted shall be the unladen kerb mass. 1.4.2.2. The fuel tank shall be filled with water to mass equal to 90 per cent of the mass of a full load of fuel as specified by the manufacturer with a tolerance of ± 1 per cent. This requirement does not apply to hydrogen fuel tanks. 1.4.2.3. All the other systems (brake, cooling, …) may be empty in this case, the mass of the liquids shall be carefully compensated. 1.4.2.4. If the mass of the measuring apparatus on board the vehicle exceeds the 25 kg allowed, it may be compensated by reductions which have no noticeable effect on the results measured under paragraph 6 below. 1.4.2.5. The mass of the measuring apparatus shall not change each axle reference load by more than 5 per cent, each variation not exceeding 20 kg. 1.4.2.6. The mass of the vehicle resulting from the provisions of paragraph 1.4.2.1 above shall be indicated in the report.8.2.2018 EN Official Journal of the European Union L 35/19 1.4.3. Passenger compartment adjustments 1.4.3.1. Position of steering wheel The steering wheel, if adjustable, shall be placed in the normal position indicated by the manufacturer or, in the absence of any particular recommendation by the manufacturer, midway between the limits of its range(s) of adjustment. At the end of propelled travel, the steering wheel shall be left free, with its spokes in the position which according to the manufacturer corresponds to straight-ahead travel of the vehicle. 1.4.3.2. Glazing The movable glazing of the vehicle shall be in the closed position. For test measurement purposes and in agreement with the manufacturer, it may be lowered, provided that the position of the operating handle corresponds to the closed position. 1.4.3.3. Gear-change lever The gear-change lever shall be in the neutral position. If the vehicle is propelled by its own engine, then the gear-change level shall be defined by the manufacturer. 1.4.3.4. Pedals The pedals shall be in their normal position of rest. If adjustable, they shall be set in their mid-position unless another position is specified by the manufacturer. 1.4.3.5. Doors The doors shall be closed but not locked. 1.4.3.5.1. In the case of vehicles equipped with an automatically activated door locking system, the system shall be activated at the start of propulsion of the vehicle in order to lock the doors automatically before the moment of impact. At the choice of the manufacturer, the doors shall be locked manually before the start of propulsion of the vehicle. 1.4.3.5.2. In the case of vehicles equipped with an automatically activated door locking system that is installed optionally and/or which can be de-activated by the driver, one of the following two procedures shall be used at the choice of the manufacturer: 1.4.3.5.2.1. The system shall be activated at the start of propulsion of the vehicle in order to lock the doors automati­ cally before the moment of impact. At the choice of the manufacturer, the doors shall be locked manually before the start of propulsion of the vehicle. 1.4.3.5.2.2. The side doors on the impacted side shall be unlocked and the system overridden for these doors; for the side doors on the non-impacted side, the system may be activated in order to lock these doors automatically before the moment of impact. At the choice of the manufacturer, these doors shall be locked manually before the start of propulsion of the vehicle. 1.4.3.6. Opening roof If an opening or removable roof is fitted, it shall be in place and in the closed position. For test measurement purposes and in agreement with the manufacturer, it may be open. 1.4.3.7. Sun-visor The sun-visors shall be in the stowed position. 1.4.3.8. Rear-view mirror The interior rear-view mirror shall be in the normal position of use. 1.4.3.9. Arm-rests Arm-rests at the front and rear, if movable, shall be in the lowered position, unless this is prevented by the position of the dummies in the vehicles.L 35/20 EN Official Journal of the European Union 8.2.2018 1.4.3.10. Head restraints Head restraints adjustable for height shall be in their appropriate position as defined by the manufacturer. In the absence of any particular recommendation from the manufacturer, then the head restraints shall be in their uppermost position. 1.4.3.11. Seats 1.4.3.11.1. Position of front seats Seats adjustable longitudinally shall be placed so that their ‘H’ point, determined in accordance with the procedure set out in Annex 6 is in the middle position of travel or in the nearest locking position thereto, and at the height position defined by the manufacturer (if independently adjustable for height). In the case of a bench seat, the reference shall be to the ‘H’ point of the driver's place. 1.4.3.11.2. Position of the front seat-backs If adjustable, the seat-backs shall be adjusted so that the resulting inclination of the torso of the dummy is as close as possible to that recommended by the manufacturer for normal use or, in the absence of any particular recommendation by the manufacturer, to 25° towards the rear from the vertical. 1.4.3.11.3. Rear seats If adjustable, the rear seats or rear bench seats shall be placed in the rearmost position. 1.4.4. Electrical power train adjustment 1.4.4.1. The REESS shall be at any state of charge, which allows the normal operation of the power train as recommended by the manufacturer. 1.4.4.2. The electrical power train shall be energized with or without the operation of the original electrical energy sources (e.g. engine-generator, REESS or electric energy conversion system), however: 1.4.4.2.1. By the agreement between Technical Service and manufacturer it shall be permissible to perform the test with all or parts of the electrical power train not being energized insofar as there is no negative influence on the test result. For parts of the electrical power train not energized, the protection against electrical shock shall be proved by either physical protection or isolation resistance and appropriate additional evidence. 1.4.4.2.2. In the case where an automatic disconnect is provided, at the request of the manufacturer it shall be permissible to perform the test with the automatic disconnect being triggered. In this case it shall be demonstrated that the automatic disconnect would have operated during the impact test. This includes the automatic activation signal as well as the galvanic separation considering the conditions as seen during the impact. 2. DUMMIES 2.1. Front seats 2.1.1. A dummy corresponding to the specifications for Hybrid III fiftieth percentile male dummy (1) fitted with a 45° ankle and meeting the specifications for its adjustment shall be installed in each of the front outboard seats in accordance with the conditions set out in Annex 5. The ankle of the dummy shall be certified in accordance with the procedures in Annex 10. 2.1.2. The car will be tested with restraint systems, as provided by the manufacturer. 3. PROPULSION AND COURSE OF VEHICLE 3.1. The vehicle shall be propelled either by its own engine or by any other propelling device. (1) The technical specifications and detailed drawings of Hybrid III corresponding to the principal dimensions of a fiftieth percentile male of the United States of America, and the specifications for its adjustment for this test are deposited with the Secretary-General of the United Nations and may be consulted on request at the secretariat of the Economic Commission for Europe, Palais des Nations, Geneva, Switzerland.8.2.2018 EN Official Journal of the European Union L 35/21 3.2. At the moment of impact the vehicle shall no longer be subject to the action of any additional steering or propelling device. 3.3. The course of the vehicle shall be such that it satisfies the requirements of paragraphs 1.2 and 1.3.1 above. 4. TEST SPEED Vehicle speed at the moment of impact shall be 56 – 0/+ 1 km/h. However, if the test was performed at a higher impact speed and the vehicle met the requirements, the test shall be considered satisfactory. 5. MEASUREMENTS TO BE MADE ON THE DUMMY IN FRONT SEATS 5.1. All the measurements necessary for the verification of the performance criteria shall be made with measurement systems corresponding to the specifications of Annex 8. 5.2. The different parameters shall be recorded through independent data channels of the following CFC (Channel Frequency Class): 5.2.1. Measurements in the head of the dummy The acceleration (a) referring to the centre of gravity is calculated from the triaxial components of the acceleration measured with a CFC of 1 000. 5.2.2. Measurements in the neck of the dummy 5.2.2.1. The axial tensile force and the fore/aft shear force at the neck/head interface are measured with a CFC of 1 000. 5.2.2.2. The bending moment about a lateral axis at the neck/head interface are measured with a CFC of 600. 5.2.3. Measurements in the thorax of the dummy The chest deflection between the sternum and the spine is measured with a CFC of 180. 5.2.4. Measurements in the femur and tibia of the dummy 5.2.4.1. The axial compressive force and the bending moments are measured with a CFC of 600. 5.2.4.2. The displacement of the tibia with respect to the femur is measured at the knee sliding joint with a CFC of 180. 6. MEASUREMENTS TO BE MADE ON THE VEHICLE 6.1. To enable the simplified test described in Annex 7 to be carried out, the deceleration time history of the structure shall be determined on the basis of the value of the longitudinal accelerometers at the base of the ‘B’ pillar on the struck side of the vehicle with a CFC of 180 by means of data channels corresponding to the requirements set out in Annex 8; 6.2. The speed time history which will be used in the test procedure described in Annex 7 shall be obtained from the longitudinal accelerometer at the ‘B’ pillar on the struck side.L 35/22 EN Official Journal of the European Union 8.2.2018 ANNEX 4 HEAD PERFORMANCE CRITERION (HPC) AND 3 MS HEAD ACCELERATION PERFORMANCE CRITERIA 1. HEAD PERFORMANCE CRITERION (HPC ) 36 1.1. The Head Performance Criterion (HPC ) is considered to be satisfied when, during the test, there is no contact 36 between the head and any vehicle component. 1.2. If, during the test, there is contact between the head and any vehicle component, a calculation of HPC is made, on the basis of the acceleration (a), measured according to paragraph 5.2.1 of Annex 3, by the following expression: � � 2,5 1 HPC¼ðt − t Þ ƒt2 adt 2 1 t − t t1 2 1 in which: 1.2.1. The term ‘a’ is the resultant acceleration measured according to paragraph 5.2.1 of Annex 3 and is measured in units of gravity, g (1 g = 9,81 m/s2); 1.2.2. If the beginning of the head contact can be determined satisfactorily, t and t are the two time instants, 1 2 expressed in seconds, defining an interval between the beginning of the head contact and the end of the recording for which the value of HPC is maximum; 1.2.3. If the beginning of the head contact cannot be determined, t and t are the two time instants, expressed in 1 2 seconds, defining a time interval between the beginning and the end of the recording for which the value of HPC is maximum; 1.2.4. Values of HPC for which the time interval (t – t ) is greater than 36 ms are ignored for the purposes of 1 2 calculating the maximum value. 1.3. The value of the resultant head acceleration during forward impact which is exceeded for 3 ms cumulatively is calculated from the resultant head acceleration measured according to paragraph 5.2.1 of Annex 3. 2. INJURY CRITERIA FOR NECK 2.1. These criteria are determined by the compressive axial force, the axial tensile force and the fore/aft shear forces at the head/neck interface, expressed in kN and measured according to paragraph 5.2.2 of Annex 3 and by the duration of these forces expressed in ms. 2.2. The neck bending moment criterion is determined by the bending moment, expressed in Nm, about a lateral axis at the head/neck interface and measured according to paragraph 5.2.2 of Annex 3. 2.3. The neck flexion bending moment, expressed in Nm, shall be recorded. 3. THORAX COMPRESSION CRITERION (THCC) AND VISCOUS CRITERION (V * C) 3.1. The thorax compression criterion is determined by the absolute value of the thorax deformation, expressed in mm and measured according to paragraph 5.2.3 of Annex 3. 3.2. The viscous criterion (V * C) is calculated as the instantaneous product of the compression and the rate of deflection of the sternum, measured according to paragraph 6. of this annex and also paragraph 5.2.3 of Annex 3.8.2.2018 EN Official Journal of the European Union L 35/23 4. FEMUR FORCE CRITERION (FFC) 4.1. This criterion is determined by the compression load expressed in kN, transmitted axially on each femur of the dummy and measured according to paragraph 5.2.4 of Annex 3 and by the duration of the compressive load expressed in ms. 5. TIBIA COMPRESSIVE FORCE CRITERION (TCFC) AND TIBIA INDEX (TI) 5.1. The tibia compressive force criterion is determined by the compressive load (Fz) expressed in kN, transmitted axially on each tibia of the dummy and measured according to paragraph 5.2.4 of Annex 3. 5.2. The tibia index is calculated on the basis of the bending moments (M and M) measured according to x y paragraph 5.1 by the following expression: � � � � � � � � TI¼ M =ðM Þ þ F =ðF Þ R C R Z C Z Where: M = bending moment about the x axis X M = bending moment about the y axis Y (M ) = critical bending moment and shall be taken to be 225 Nm CR F = compressive axial force in the z direction Z (F ) = critical compressive force in the z direction and shall be taken to be 35,9 kN and CZ qffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffi M ¼ ðM Þ2þðM Þ2 R X Y The tibia index is calculated for the top and the bottom of each tibia; however, F may be measured at either z location. The value obtained is used for the top and bottom TI calculations. Moments M and M are both x y measured separately at both locations. 6. PROCEDURE FOR CALCULATING THE VISCOUS CRITERIA (V * C) FOR HYBRID III DUMMY 6.1. The viscous criterion is calculated as the instantaneous product of the compression and the rate of deflection of the sternum. Both are derived from the measurement of sternum deflection. 6.2. The sternum deflection response is filtered once at CFC 180. The compression at time t is calculated from this filtered signal as: D C ¼ ðtÞ ðtÞ 0,229 The sternum deflection velocity at time t is calculated from the filtered deflection as: 8ðD − D Þ − ðD − D Þ V ¼ ðt þ 1Þ ðt − 1Þ ðt þ 2Þ ðt − 2Þ ðtÞ 12 @tL 35/24 EN Official Journal of the European Union 8.2.2018 Where D is the deflection at time t in metres and @t is the time interval in seconds between the measurements (t) of deflection. The maximum value of @t shall be 1,25 × 10– 4 seconds. This calculation procedure is shown diagrammatically below:8.2.2018 EN Official Journal of the European Union L 35/25 ANNEX 5 ARRANGEMENT AND INSTALLATION OF DUMMIES AND ADJUSTMENT OF RESTRAINT SYSTEMS 1. ARRANGEMENT OF DUMMIES 1.1. Separate seats The plane of symmetry of the dummy shall coincide with the vertical median plane of the seat. 1.2. Front bench seat 1.2.1. Driver The plane of symmetry of the dummy shall lie in the vertical plane passing through the steering wheel centre and parallel to the longitudinal median plane of the vehicle. If the seating position is determined by the shape of the bench, such seat shall be regarded as a separate seat. 1.2.2. Outer passenger The plane of symmetry of the dummy shall be symmetrical with that of the driver dummy relative to the longitudinal median plane of the vehicle. If the seating position is determined by the shape of the bench, such seat shall be regarded as a separate seat. 1.3. Bench seat for front passengers (not including driver) The planes of symmetry of the dummy shall coincide with the median planes of the seating positions defined by the manufacturer. 2. INSTALLATION OF DUMMIES 2.1. Head The transverse instrumentation platform of the head shall be horizontal within 2,5°. To level the head of the test dummy in vehicles with upright seats with non-adjustable backs, the following sequences must be followed. First adjust the position of the ‘H’ point within the limits set forth in paragraph 2.4.3.1 below to level the transverse instrumentation platform of the head of the test dummy. If the transverse instrumentation platform of the head is still not level, then adjust the pelvic angle of the test dummy within the limits provided in paragraph 2.4.3.2 below. If the transverse instrumentation platform of the head is still not level, then adjust the neck bracket of the test dummy the minimum amount necessary to ensure that the transverse instrumentation platform of the head is horizontal within 2,5°. 2.2. Arms 2.2.1. The driver's upper arms shall be adjacent to the torso with the centrelines as close to a vertical plane as possible. 2.2.2. The passenger's upper arms shall be in contact with the seat back and the sides of the torso. 2.3. Hands 2.3.1. The palms of the driver test dummy shall be in contact with the outer part of the steering wheel rim at the rim's horizontal centreline. The thumbs shall be over the steering wheel rim and shall be lightly taped to the steering wheel rim so that if the hand of the test dummy is pushed upward by a force of not less than 9 N and not more than 22 N, the tape shall release the hand from the steering wheel rim. 2.3.2. The palms of the passenger test dummy shall be in contact with outside of thigh. The little finger shall be in contact with the seat cushion.L 35/26 EN Official Journal of the European Union 8.2.2018 2.4. Torso 2.4.1. In vehicles equipped with bench seats, the upper torso of the driver and passenger test dummies shall rest against the seat back. The midsagittal plane of the driver dummy shall be vertical and parallel to the vehicle's longitudinal centreline, and pass through the centre of the steering wheel rim. The midsagittal plane of the passenger dummy shall be vertical and parallel to the vehicle's longitudinal centreline and the same distance from the vehicle's longitudinal centreline as the midsagittal plane of the driver dummy. 2.4.2. In vehicles equipped with individual seats, the upper torso of the driver and passenger test dummies shall rest against the seat back. The midsagittal plane of the driver and the passenger dummy shall be vertical and shall coincide with the longitudinal centreline of the individual seat. 2.4.3. Lower torso 2.4.3.1. ‘H’ point The ‘H’ point of the driver and passenger test dummies shall coincide within 13 mm in the vertical dimension and 13 mm in the horizontal dimension, with a point 6 mm below the position of the ‘H’ point determined using the procedure described in Annex 6 except that the length of the lower leg and thigh segments of the ‘H’ point machine shall be adjusted to 414 and 401 mm, instead of 417 and 432 mm respectively. 2.4.3.2. Pelvic angle As determined using the pelvic angle gauge (GM) drawing 78051-532 incorporated by reference in Part 572, which is inserted into the ‘H’ point gauging hole of the dummy, the angle measured from the horizontal on the 76,2 mm (3 inch) flat surface of the gauge shall be 22,5 degrees plus or minus 2,5 degrees. 2.5. Legs The upper legs of the driver and passenger test dummies shall rest against the seat cushion to the extent permitted by placement of the feet. The initial distance between the outboard knee clevis flange surfaces shall be 270 mm ± 10 mm. To the extent practicable, the left leg of the driver dummy and both legs of the passenger dummy shall be in vertical longitudinal planes. To the extent practicable, the right leg of the driver dummy shall be in a vertical plane. Final adjustment to accommodate placement of feet in accordance with paragraph 2.6 for various passenger compartment configurations is permitted. 2.6. Feet 2.6.1. The right foot of the driver test dummy shall rest on the undepressed accelerator with the rearmost point of the heel on the floor surface in the plane of the pedal. If the foot cannot be placed on the accelerator pedal, it shall be positioned perpendicular to the tibia and placed as far forward as possible in the direction of the centreline of the pedal with the rearmost point of the heel resting on the floor surface. The heel of the left foot shall be placed as far forward as possible and shall rest on the floor pan. The left foot shall be positioned as flat as possible on the toe board. The longitudinal centreline of the left foot shall be placed as parallel as possible to the longitudinal centreline of the vehicle. For vehicles equipped with a footrest, it shall be possible at the request of the manufacturer to place the left foot on the footrest. In this case the position of the left foot is defined by the footrest. 2.6.2. The heels of both feet of the passenger test dummy shall be placed as far forward as possible and shall rest on the floor pan. Both feet shall be positioned as flat as possible on the toe board. The longitudinal centreline of the feet shall be placed as parallel as possible to the longitudinal centreline of the vehicle. 2.7. The measuring instruments installed shall not in any way affect the movement of the dummy during impact. 2.8. The temperature of the dummy and the system of measuring instruments shall be stabilized before the test and maintained so far as possible within a range between 19 °C and 22,2 °C. 2.9. Dummy clothing 2.9.1. The instrumented dummies will be clothed in formfitting cotton stretch garments with short sleeves and mid- calf length trousers specified in FMVSS 208, drawings 78051-292 and 293 or their equivalent.8.2.2018 EN Official Journal of the European Union L 35/27 2.9.2. A size 11XW shoe, which meets the configuration size, sole and heel thickness specifications of the US military standard MIL S 13192, revision P and whose weight is 0,57 ± 0,1 kg, shall be placed and fastened on each foot of the test dummies. 3. ADJUSTMENT OF RESTRAINT SYSTEM The dummy jacket shall be installed at the appropriate position where the bolt hole of the neck lower bracket and the work hole of the dummy jacket are at the same position. With the test dummy at its designated seating position, as specified by the appropriate requirements of paragraphs 2.1 to 2.6 and 3.1 to 3.6 above, place the belt around the test dummy and fasten the latch. Remove all slack from the lap belt. Pull the upper torso webbing out of the retractor horizontally at a position via the centre of the dummy and allow it to retract. Repeat this operation four times. The shoulder belt should be at the position in the area which shall not be taken off from shoulder and shall not contact with the neck. For Hybrid III fiftieth percentile male dummy the seat belt path shall be positioned so that the hole of the outer side dummy jacket is not fully hidden by the seat belt. Apply a 9 to 18 N tension load to the lap belt. If the belt system is equipped with a tension-relieving device, introduce the maximum amount of slack into the upper torso belt that is recommended by the manufacturer for normal use in the owner's manual for the vehicle. If the belt system is not equipped with a tension-relieving device, allow the excess webbing in the shoulder belt to be retracted by the rewind force of the retractor. Where the safety belt and safety belt anchorages are located such that the belt does not lie as required above then the safety belt may be manually adjusted and retained by tape.L 35/28 EN Official Journal of the European Union 8.2.2018 ANNEX 6 Procedure for determining the ‘H’ point and the actual torso angle for seating positions in motor vehicles (1) Appendix 1 — Description of the three dimensional ‘H’ point machine (3-D H machine) (1) Appendix 2 — Three-dimensional reference system (1) Appendix 3 — Reference data concerning seating positions (1) (1) The procedure is described in Annex 1 to the Consolidated Resolution on the Construction of Vehicles (RE.3) (document ECE/TRANS/WP.29/78/Rev.2). www.unece.org/trans/main/wp29/wp29wgs/wp29gen/wp29resolutions.html8.2.2018 EN Official Journal of the European Union L 35/29 ANNEX 7 TEST PROCEDURE WITH TROLLEY 1. TEST INSTALLATION AND PROCEDURE 1.1. Trolley The trolley shall be so constructed that no permanent deformation appears after the test. It shall be so guided that, during the impact phase, the deviation in the vertical plane does not exceed 5° and 2° in the horizontal plane. 1.2. State of the structure 1.2.1. General The structure tested shall be representative of the series production of the vehicles concerned. Some components may be replaced or removed where such replacement or removal clearly has no effect on the test results. 1.2.2. Adjustments Adjustments shall conform to those set out in paragraph 1.4.3 of Annex 3 to this Regulation, taking into account what is stated in paragraph 1.2.1 above. 1.3. Attachment of the structure 1.3.1. The structure shall be firmly attached to the trolley in such a way that no relative displacement occurs during the test. 1.3.2. The method used to fasten the structure to the trolley shall not have the effect of strengthening the seat anchorages or restraint devices, or of producing any abnormal deformation of the structure. 1.3.3. The attachment device recommended is that whereby the structure rests on supports placed approximately in the axis of the wheels or, if possible, whereby the structure is secured to the trolley by the fastenings of the suspension system. 1.3.4. The angle between the longitudinal axis of the vehicle and the direction of motion of the trolley shall be 0° ± 2°. 1.4. Dummies The dummies and their positioning shall conform to the specifications in Annex 3, paragraph 2. 1.5. Measuring apparatus 1.5.1. Deceleration of the structure The position of the transducers measuring the deceleration of the structure during the impact shall be parallel to the longitudinal axis of the trolley according to the specifications of Annex 8 (CFC 180). 1.5.2. Measurements to be made on the dummies All the measurements necessary for checking the listed criteria are set out in Annex 3, paragraph 5. 1.6. Deceleration curve of the structure The deceleration curve of the structure during the impact phase shall be such that the ‘variation of speed in relation to time’ curve obtained by integration at no point differs by more than ± 1 m/s from the ‘variation of speed in relation to time’ reference curve of the vehicle concerned as defined in appendix to this annex. A displacement with regard to the time axis of the reference curve may be used to obtain the structure velocity inside the corridor.L 35/30 EN Official Journal of the European Union 8.2.2018 1.7. Reference curve ΔV = f(t) of the vehicle concerned This reference curve is obtained by integration of the deceleration curve of the vehicle concerned measured in the frontal collision test against a barrier as provided for in paragraph 6 of Annex 3 to this Regulation. 1.8. Equivalent method The test may be performed by some other method than that of deceleration of a trolley, provided that such method complies with the requirement concerning the range of variation of speed described in paragraph 1.6 above.8.2.2018 EN Official Journal of the European Union L 35/31 APPENDIX EQUIVALENCE CURVE — TOLERANCE BAND FOR CURVE ΔV = f(t)L 35/32 EN Official Journal of the European Union 8.2.2018 ANNEX 8 TECHNIQUE OF MEASUREMENT IN MEASUREMENT TESTS: INSTRUMENTATION 1. DEFINITIONS 1.1. Data channel A data channel comprises all the instrumentation from a transducer (or multiple transducers whose outputs are combined in some specified way) up to and including any analysis procedures that may alter the frequency content or the amplitude content of data. 1.2. Transducer The first device in a data channel used to convert a physical quantity to be measured into a second quantity (such as an electrical voltage) which can be processed by the remainder of the channel. 1.3. Channel Amplitude Class: CAC The designation for a data channel that meets certain amplitude characteristics as specified in this annex. The CAC number is numerically equal to the upper limit of the measurement range. 1.4. Characteristic frequencies F , F, F H L N These frequencies are defined in Figure 1 of this annex. 1.5. Channels Frequency Class: CFC The channel frequency class is designated by a number indicating that the channel frequency response lies within the limits specified in Figure 1 of this annex. This number and the value of the frequency F in Hz are H numerically equal. 1.6. Sensitivity coefficient The slope of the straight line representing the best fit to the calibration values determined by the method of least square within the channel amplitude class. 1.7. Calibration factor of a data channel The mean value of the sensitivity coefficients evaluated over frequencies which are evenly spaced on F a logarithmic scale between F and H L 2,5 1.8. Linearity error The ratio, in per cent, of the maximum difference between the calibration value and the corresponding value read on the straight line defined in paragraph 1.6 above at the upper limit of the channel amplitude class. 1.9. Cross sensitivity The ratio of the output signal to the input signal, when an excitation is applied to the transducer perpen­ dicular to the measurement axis. It is expressed as a percentage of the sensitivity along the measurement axis. 1.10. Phase delay time The phase delay time of a data channel is equal to the phase delay (in radians) of a sinusoidal signal, divided by the angular frequency of that signal (in radians/second). 1.11. Environment The aggregate, at a given moment, of all external conditions and influences to which the data channel is subjected.8.2.2018 EN Official Journal of the European Union L 35/33 2. PERFORMANCE REQUIREMENTS 2.1. Linearity error The absolute value of the linearity error of a data channel at any frequency in the CFC, shall be equal to or less than 2,5 per cent of the value of the CAC, over the whole measurement range. 2.2. Amplitude against frequency The frequency response of a data channel shall lie within the limiting curves given in Figure 1 of this annex. The zero dB line is determined by the calibration factor. 2.3. Phase delay time The phase delay time between the input and the output signals of a data channel shall be determined and shall not vary by more than 0,1 F seconds between 0,03 F and F . H H H 2.4. Time 2.4.1. Time base A time base shall be recorded and shall at least give 1/100 s with an accuracy of 1 per cent. 2.4.2. Relative time delay The relative time delay between the signal of two or more data channels, regardless of their frequency class, must not exceed 1 ms excluding delay caused by phase shift. Two or more data channels of which the signals are combined shall have the same frequency class and shall not have relative time delay greater than 1/10 F seconds. H This requirement applies to analogue signals as well as to synchronization pulses and digital signals. 2.5. Transducer cross sensitivity The transducer cross sensitivity shall be less than 5 per cent in any direction. 2.6. Calibration 2.6.1. General A data channel shall be calibrated at least once a year against reference equipment traceable to known standards. The methods used to carry out a comparison with reference equipment shall not introduce an error greater than 1 per cent of the CAC. The use of the reference equipment is limited to the frequency range for which they have been calibrated. Subsystems of a data channel may be evaluated individually and the results factored into the accuracy of the total data channel. This can be done for example by an electrical signal of known amplitude simulating the output signal of the transducer which allows a check to be made on the gain factor of the data channel, excluding the transducer. 2.6.2. Accuracy of reference equipment for calibration The accuracy of the reference equipment shall be certified or endorsed by an official metrology service. 2.6.2.1. Static calibration 2.6.2.1.1. Accelerations The errors shall be less than ± 1,5 per cent of the channel amplitude class.L 35/34 EN Official Journal of the European Union 8.2.2018 2.6.2.1.2. Forces The error shall be less than ± 1 per cent of the channel amplitude class. 2.6.2.1.3. Displacements The error shall be less than ± 1 per cent of the channel amplitude class. 2.6.2.2. Dynamic calibration 2.6.2.2.1. Accelerations The error in the reference accelerations expressed as a percentage of the channel amplitude class shall be less than ± 1,5 per cent below 400 Hz, less than ± 2 per cent between 400 Hz and 900 Hz, and less than ± 2,5 per cent above 900 Hz. 2.6.2.3. Time The relative error in the reference time shall be less than 10– 5. 2.6.3. Sensitivity coefficient and linearity error The sensitivity coefficient and the linearity error shall be determined by measuring the output signal of the data channel against a known input signal for various values of this signal. The calibration of the data channel shall cover the whole range of the amplitude class. For bi-directional channels, both the positive and negative values shall be used. If the calibration equipment cannot produce the required input owing to the excessively high values of the quantity to be measured, calibrations shall be carried out within the limits of the calibration standards and these limits shall be recorded in the test report. A total data channel shall be calibrated at a frequency or at a spectrum of frequencies having a significant F value between F and H L 2,5 2.6.4. Calibration of the frequency response The response curves of phase and amplitude against frequency shall be determined by measuring the output signals of the data channel in terms of phase and amplitude against a known input signal, for various values of this signal varying between F and 10 times the CFC or 3 000 Hz, whichever is lower. L 2.7. Environmental effects A regular check shall be made to identify any environmental influence (such as electric or magnetic flux, cable velocity, etc.). This can be done for instance by recording the output of spare channels equipped with dummy transducers. If significant output signals are obtained corrective action shall be taken, for instance by replacement of cables. 2.8. Choice and designation of the data channel The CAC and CFC define a data channel. The CAC shall be 1, 2 or 5 to a power of ten. 3. MOUNTING OF TRANSDUCERS Transducers should be rigidly secured so that their recordings are affected by vibration as little as possible. Any mounting having a lowest resonance frequency equal to at least 5 times the frequency F of the data H8.2.2018 EN Official Journal of the European Union L 35/35 channel considered shall be considered valid. Acceleration transducers in particular should be mounted in such a way that the initial angle of the real measurement axis to the corresponding axis of the reference axis system is not greater than 5° unless an analytical or experimental assessment of the effect of the mounting on the collected data is made. When multi-axial accelerations at a point are to be measured, each acceleration transducer axis should pass within 10 mm of that point, and the centre of seismic mass of each accelerometer should be within 30 mm of that point. 4. DATA PROCESSING 4.1. Filtering Filtering corresponding to the frequencies of the data channel class may be carried out during either recording or processing of data. However, before recording, analogical filtering at a higher level than CFC should be effected in order to use at least 50 per cent of the dynamic range of the recorder and to reduce the risk of high frequencies saturating the recorder or causing aliasing errors in the digitalizing process. 4.2. Digitalizing 4.2.1. Sampling frequency The sampling frequency should be equal to at least 8 F . In the case of analogical recording, when the H recording and reading speeds are different, the sampling frequency can be divided by the speed ratio. 4.2.2. Amplitude resolution The size of digital words should be at least 7 bits and a parity bit. 5. PRESENTATION OF RESULTS The results should be presented on A4 size paper (ISO/R 216). Results presented as diagrams should have axes scaled with a measurement unit corresponding to a suitable multiple of the chosen unit (for example, 1, 2, 5, 10, 20 millimetres). SI units shall be used, except for vehicle velocity, where km/h may be used, and for accelerations due to impact where g, with g = 9,8 m/s2, may be used. Figure 1 Frequency response curveL 35/36 EN Official Journal of the European Union 8.2.2018 F F F N Logarithmic scale CFC L H N Hz Hz Hz a ± 0,5 dB 1 000 ≤ 0,1 1 000 1 650 b + 0,5; – 1 dB c + 0,5; – 4 dB 600 ≤ 0,1 600 1 000 d – 9 dB/octave 180 ≤ 0,1 180 300 e – 24 dB/octave f ∞ 60 ≤ 0,1 60 100 g – 308.2.2018 EN Official Journal of the European Union L 35/37 ANNEX 9 DEFINITION OF DEFORMABLE BARRIER 1. COMPONENT AND MATERIAL SPECIFICATIONS The dimensions of the barrier are illustrated in Figure 1 of this annex. The dimensions of the individual components of the barrier are listed separately below. 1.1. Main honeycomb block Dimensions: Height: 650 mm (in direction of honeycomb ribbon axis) Width: 1 000 mm Depth: 450 mm (in direction of honeycomb cell axes) All above dimensions should allow a tolerance of ± 2,5 mm Material: Aluminium 3003 (ISO 209, Part 1) Foil Thickness: 0,076 mm ± 15 per cent Cell Size: 19,1 mm ± 20 per cent Density: 28,6 kg/m3 ± 20 per cent Crush Strength: 0,342 MPa + 0 per cent – 10 per cent (1) 1.2. Bumper element Dimensions: Height: 330 mm (in direction of honeycomb ribbon axis) Width: 1 000 mm Depth: 90 mm (in direction of honeycomb cell axes) All above dimensions should allow a tolerance of ± 2,5 mm Material: Aluminium 3003 (ISO 209, Part 1) Foil Thickness: 0,076 mm ± 15 per cent Cell Size: 6,4 mm ± 20 per cent Density: 82,6 kg/m3 ± 20 per cent Crush Strength: 1,711 MPa + 0 per cent – 10 per cent (1) 1.3. Backing sheet Dimensions Height: 800 mm ± 2,5 mm Width: 1 000 mm ± 2,5 mm Thickness: 2,0 mm ± 0,1 mm (1) In accordance with the certification procedure described in paragraph 2 of this annex.L 35/38 EN Official Journal of the European Union 8.2.2018 1.4. Cladding sheet Dimensions Length: 1 700 mm ± 2,5 mm Width: 1 000 mm ± 2,5 mm Thickness: 0,81 ± 0,07 mm Material: Aluminium 5251/5052 (ISO 209, part 1) 1.5. Bumper facing sheet Dimensions Height: 330 mm ± 2,5 mm Width: 1 000 mm ± 2,5 mm Thickness: 0,81 mm ± 0,07 mm Material: Aluminium 5251/5052 (ISO 209, part 1) 1.6. Adhesive The adhesive to be used throughout should be a two-part polyurethane (such as Ciba-Geigy XB5090/1 resin with XB5304 hardener, or equivalent). 2. ALUMINIUM HONEYCOMB CERTIFICATION A complete testing procedure for certification of aluminium honeycomb is given in NHTSA TP-214D. The following is a summary of the procedure that should be applied to materials for the frontal impact barrier, these materials having a crush strength of 0,342 MPa and 1,711 MPa respectively. 2.1. Sample locations To ensure uniformity of crush strength across the whole of the barrier face, eight samples shall be taken from four locations evenly spaced across the honeycomb block. For a block to pass certification, seven of these eight samples shall meet the crush strength requirements of the following sections. The location of the samples depends on the size of the honeycomb block. First, four samples, each measuring 300 mm × 300 mm × 50 mm thick shall be cut from the block of barrier face material. Please refer to Figure 2 of this annex for an illustration of how to locate these sections within the honeycomb block. Each of these larger samples shall be cut into samples for certification testing (150 mm × 150 mm × 50 mm). Certification shall be based on the testing of two samples from each of these four locations. The other two should be made available to the applicant, upon request. 2.2. Sample size Samples of the following size shall be used for testing: Length: 150 mm ± 6 mm Width: 150 mm ± 6 mm Thickness: 50 mm ± 2 mm The walls of incomplete cells around the edge of the sample shall be trimmed as follows: In the ‘W’ direction, the fringes shall be no greater than 1,8 mm (see Figure 3 of this annex). In the ‘L’ direction, half the length of one bonded cell wall (in the ribbon direction) shall be left at either end of the specimen (see Figure 3 of this annex).8.2.2018 EN Official Journal of the European Union L 35/39 2.3. Area measurement The length of the sample shall be measured in three locations, 12,7 mm from each end and in the middle, and recorded as L , L and L (Figure 3 of this annex). In the same manner, the width shall be measured and recorded as 1 2 3 W , W and W (Figure 3 of this annex). These measurements shall be taken on the centreline of the thickness. The 1 2 3 crush area shall then be calculated as: ðL þL þL Þ ðW þW þW Þ A¼ 1 2 3 � 1 2 3 3 3 2.4. Crush rate and distance The sample shall be crushed at a rate of not less than 5,1 mm/min and not more than 7,6 mm/min. The minimum crush distance shall be 16,5 mm. 2.5. Data collection Force versus deflection data are to be collected in either analogue or digital form for each sample tested. If analogue data are collected then a means of converting this to digital shall be available. All digital data shall be collected at a rate of not less than 5 Hz (5 points per second). 2.6. Crush strength determination Ignore all data prior to 6,4 mm of crush and after 16,5 mm of crush. Divide the remaining data into three sections or displacement intervals (n = 1, 2, 3) (see Figure 4 of this annex) as follows: (1) 06,4 mm-09,7 mm inclusive, (2) 09,7 mm-13,2 mm exclusive, (3) 13,2 mm-16,5 mm inclusive. Find the average for each section as follows: ðFðnÞ 1þFðnÞ 2þ…þFðnÞmÞ FðnÞ¼ ; m = 1, 2, 3 m Where m represents the number of data points measured in each of the three intervals. Calculate the crush strength of each section as follows: FðnÞ SðnÞ¼ ; n = 1, 2, 3 A 2.7. Sample crush strength specification For a honeycomb sample to pass this certification, the following conditions shall be met: 0,308 MPa ≤ S(n) ≤ 0,342 MPa for 0,342 MPa material 1,540 MPa ≤ S(n) ≤ 1,711 MPa for 1,711 MPa material n = 1, 2, 3. 2.8. Block crush strength specification Eight samples are to be tested from four locations, evenly spaced across the block. For a block to pass certification, seven of the eight samples shall meet the crush strength specification of the previous section.L 35/40 EN Official Journal of the European Union 8.2.2018 3. ADHESIVE BONDING PROCEDURE 3.1. Immediately before bonding, aluminium sheet surfaces to be bonded shall be thoroughly cleaned using a suitable solvent, such as 1-1-1 Trichloroethane. This is to be carried out at least twice or as required to eliminate grease or dirt deposits. The cleaned surfaces shall then be abraded using 120 grit abrasive paper. Metallic/Silicon Carbide abrasive paper is not to be used. The surfaces shall be thoroughly abraded and the abrasive paper changed regularly during the process to avoid clogging, which may lead to a polishing effect. Following abrading, the surfaces shall be thoroughly cleaned again, as above. In total, the surfaces shall be solvent cleaned at least four times. All dust and deposits left as a result of the abrading process shall be removed, as these will adversely affect bonding. 3.2. The adhesive should be applied to one surface only, using a ribbed rubber roller. In cases where honeycomb is to be bonded to aluminium sheet, the adhesive should be applied to the aluminium sheet only. A maximum of 0,5 kg/m2 shall be applied evenly over the surface, giving a maximum film thickness of 0,5 mm. 4. CONSTRUCTION 4.1. The main honeycomb block shall be bonded to the backing sheet with adhesive such that the cell axes are perpen­ dicular to the sheet. The cladding shall be bonded to the front surface of the honeycomb block. The top and bottom surfaces of the cladding sheet shall not be bonded to the main honeycomb block but should be positioned closely to it. The cladding sheet shall be adhesively bonded to the backing sheet at the mounting flanges. 4.2. The bumper element shall be adhesively bonded to the front of the cladding sheet such that the cell axes are perpendicular to the sheet. The bottom of the bumper element shall be flush with the bottom surface of the cladding sheet. The bumper facing sheet shall be adhesively bonded to the front of the bumper element. 4.3. The bumper element shall then be divided into three equal sections by means of two horizontal slots. These slots shall be cut through the entire depth of the bumper section and extend the whole width of the bumper. The slots shall be cut using a saw; their width shall be the width of the blade used and shall not exceed 4,0 mm. 4.4. Clearance holes for mounting the barrier are to be drilled in the mounting flanges (shown in Figure 5 of this annex). The holes shall be of 9,5 mm diameter. Five holes shall be drilled in the top flange at a distance of 40 mm from the top edge of the flange and five in the bottom flange, 40 mm from the bottom edge of that flange. The holes shall be at 100 mm, 300 mm, 500 mm, 700 mm, 900 mm from either edge of the barrier. All holes shall be drilled to ± 1 mm of the nominal distances. These holes locations are a recommendation only. Alternative positions may be used which offer at least the mounting strength and security provided by the above mounting specifications. 5. MOUNTING 5.1. The deformable barrier shall be rigidly fixed to the edge of a mass of not less than 7 × 104 kg or to some structure attached thereto. The attachment of the barrier face shall be such that the vehicle shall not contact any part of the structure more than 75 mm from the top surface of the barrier (excluding the upper flange) during any stage of the impact (1). The front face of the surface to which the deformable barrier is attached shall be flat and continuous over the height and width of the face and shall be vertical ± 1° and perpendicular ± 1° to the axis of the run-up track. The attachment surface shall not be displaced by more than 10 mm during the test. If necessary, additional anchorage or arresting devices shall be used to prevent displacement of the concrete block. The edge of the deformable barrier shall be aligned with the edge of the concrete block appropriate for the side of the vehicle to be tested. 5.2. The deformable barrier shall be fixed to the concrete block by means of ten bolts, five in the top mounting flange and five in the bottom. These bolts shall be of at least 8 mm diameter. Steel clamping strips shall be used for both the top and bottom mounting flanges (see Figures 1 and 5 of this annex). These strips shall be 60 mm high and 1 000 mm wide and have a thickness of at least 3 mm. The edges of the clamping strips should be rounded-off to prevent tearing of the barrier against the strip during impact. The edge of the strip should be located no more than 5 mm above the base of the upper barrier-mounting flange, or 5 mm below the top of the lower barrier-mounting flange. Five clearance holes of 9,5 mm diameter must be drilled in both strips to correspond with those in the mounting flange on the barrier (see paragraph 4 above). The mounting strip and barrier flange holes may be (1) A mass, the end of which is between 125 mm and 925 mm high and1 000 mm deep, is considered to satisfy this requirement.8.2.2018 EN Official Journal of the European Union L 35/41 widened from 9,5 mm up to a maximum of 25 mm in order to accommodate differences in back-plate arrangements and/or load cell wall hole configurations. None of the fixtures shall fail in the impact test. In the case where the deformable barrier is mounted on a load cell wall (LCW) it should be noted that the above dimensional requirements for mountings are intended as a minimum. Where a LCW is present, the mounting strips may be extended to accommodate higher mounting holes for the bolts. If the strips are required to be extended, then thicker gauge steel should be used accordingly, such that the barrier does not pull away from the wall, bend or tear during the impact. If an alternative method of mounting the barrier is used, it should be at least as secure as that specified in the above paragraphs. Figure 1 Deformable barrier for frontal impact testing Barrier width: 1 000 mm All dimensions in mm.L 35/42 EN Official Journal of the European Union 8.2.2018 Figure 2 Locations of samples for certification If a ≥ 900 mm: x = 1/3 (b-600 mm) and y = 1/3 (a – 600 mm) (for a ≤ b) If a < 900 mm: x = 1/5 (b-1 200 mm) and y = 1/2 (a – 300 mm) (for a ≤ b)8.2.2018 EN Official Journal of the European Union L 35/43 Figure 3 Honeycomb axes and measured dimensions e = d/2 f = 0,8 mm Figure 4 Crush force and displacementL 35/44 EN Official Journal of the European Union 8.2.2018 Figure 5 Positions of holes for barrier mounting Hole diameters 9,5 mm. All dimensions in mm.8.2.2018 EN Official Journal of the European Union L 35/45 ANNEX 10 CERTIFICATION PROCEDURE FOR THE DUMMY LOWER LEG AND FOOT 1. UPPER FOOT IMPACT TEST 1.1. The objective of this test is to measure the response of the Hybrid III foot and ankle to well-defined, hard faced pendulum impacts. 1.2. The complete Hybrid III lower leg assembly, left (86-5001-001) and right (86-5001-002), equipped with the foot and ankle assembly, left (78051-614) and right (78051-615), shall be used, including the knee assembly. The load cell simulator (78051-319 Rev A) shall be used to secure the knee assembly (79051-16 Rev B) to the test fixture. 1.3. Test procedure 1.3.1. Each leg assembly shall be maintained (soaked) for four hours prior to the test at a temperature of 22 °C ± 3 °C and a relative humidity of 40 ± 30 per cent. The soak period shall not include the time required to reach steady state conditions. 1.3.2. Clean the impact surface of the skin and also the impactor face with isopropyl alcohol or equivalent prior to the test. Dust with talc. 1.3.3. Align the impactor accelerometer with its sensitive axis parallel to the direction of impact at contact with the foot. 1.3.4. Mount the leg assembly to the fixture shown in Figure 1 of this annex. The test fixture shall be rigidly secured to prevent movement during impact. The centre line of the femur load cell simulator (78051-319) shall be vertical with a tolerance of ± 0,5°. Adjust the mount such that the line joining the knee clevis joint and the ankle attachment bolt is horizontal with a tolerance of ± 3°, with the heel resting on two sheets of a flat low friction (PTFE sheet) surface. Ensure that the tibia flesh is located fully towards the knee end of the tibia. Adjust the ankle such that the plane of the underside of the foot is vertical and perpendicular to the direction of impact with a tolerance of ± 3° and such that the mid sagittal plane of the foot is aligned with the pendulum arm. Adjust the knee joint to 1,5 ± 0,5 g range before each test. Adjust the ankle joint so that it is free and then tighten just sufficiently to keep the foot stable on the PTFE sheet. 1.3.5. The rigid impactor comprises a horizontal cylinder diameter 50 ± 2 mm and a pendulum support arm diameter 19 ± 1 mm (Figure 4 of this annex). The cylinder has a mass of 1,25 ± 0,02 kg including instrumentation and any part of the support arm within the cylinder. The pendulum arm has a mass of 285 ± 5 g. The mass of any rotating part of the axle to which the support arm is attached should not be greater than 100 g. The length between the central horizontal axis of the impactor cylinder and the axis of rotation of the whole pendulum shall be 1 250 ± 1 mm. The impact cylinder is mounted with its longitudinal axis horizontal and perpendicular to the direction of impact. The pendulum shall impact the underside of the foot, at a distance of 185 ± 2 mm from the base of the heel resting on the rigid horizontal platform, so that the longitudinal centre line of the pendulum arm falls within 1° of a vertical line at impact. The impactor shall be guided to exclude significant lateral, vertical or rotational movement. 1.3.6. Allow a period of at least 30 minutes between successive tests on the same leg. 1.3.7. The data acquisition system, including transducers, shall conform to the specifications for CFC 600, as described in Annex 8. 1.4. Performance specification 1.4.1. When each ball of the foot is impacted at 6,7 (± 0,1) m/s in accordance with paragraph 1.3 above, the maximum lower tibia bending momentum about the y-axis (M) shall be 120 ± 25 Nm. y 2. LOWER FOOT IMPACT TEST WITHOUT SHOE 2.1. The objective of this test is to measure the response of the Hybrid III foot skin and insert to well-defined, hard faced pendulum impacts.L 35/46 EN Official Journal of the European Union 8.2.2018 2.2. The complete Hybrid III lower leg assembly, left (86-5001-001) and right (86-5001-002), equipped with the foot and ankle assembly, left (78051-614) and right (78051-615), shall be used, including the knee assembly. The load cell simulator (78051-319 Rev A) shall be used to secure the knee assembly (79051-16 Rev B) to the test fixture. 2.3. Test procedure 2.3.1. Each leg assembly shall be maintained (soaked) for four hours prior to the test at a temperature of 22 ± 3 °C and a relative humidity of 40 ± 30 per cent. The soak period shall not include the time required to reach steady state conditions. 2.3.2. Clean the impact surface of the skin and also the impactor face with isopropyl alcohol or equivalent prior to the test. Dust with talc. Check that there is no visible damage to the energy absorbing insert to the heel. 2.3.3. Align the impactor accelerometer with its sensitive axis parallel to the impactor longitudinal centre line. 2.3.4. Mount the leg assembly to the fixture shown in Figure 2 of this annex. The test fixture shall be rigidly secured to prevent movement during impact. The centre line of the femur load cell simulator (78051-319) shall be vertical with a tolerance of ± 0,5°. Adjust the mount such that the line joining the knee clevis joint and the ankle attachment bolt is horizontal with a tolerance of ± 3° with the heel resting on two sheets of a flat low friction (PTFE sheet) surface. Ensure that the tibia flesh is located fully towards the knee end of the tibia. Adjust the ankle such that the plane of the underside of the foot is vertical and perpendicular to the direction of the impact with a tolerance of ± 3° and such that the mid sagittal plane of the foot is aligned with the pendulum arm. Adjust the knee joint to 1,5 ± 0,5 g range before each test. Adjust the ankle joint so that it is free and then tighten just sufficiently to keep the foot stable on the PTFE sheet. 2.3.5. The rigid impactor comprises a horizontal cylinder diameter 50 ± 2 mm and a pendulum support arm diameter 19 ± 1 mm (Figure 4 of this annex). The cylinder has a mass of 1,25 ± 0,02 kg including instrumentation and any part of the support arm within the cylinder. The pendulum arm has a mass of 285 ± 5 g. The mass of any rotating part of the axle to which the support arm is attached should not be greater than 100 g. The length between the central horizontal axis of the impactor cylinder and the axis of rotation of the whole pendulum shall be 1 250 ± 1 mm. The impact cylinder is mounted with its longitudinal axis horizontal and perpendicular to the direction of impact. The pendulum shall impact the underside of the foot, at a distance of 62 ± 2 mm from the base of the heel resting on the rigid horizontal platform, so that the longitudinal centreline of the pendulum arm falls within 1° of a vertical line at impact. The impactor shall be guided to exclude significant lateral, vertical or rotational movement. 2.3.6. Allow a period of at least 30 minutes between successive tests on the same leg. 2.3.7. The data acquisition system, including transducers, shall conform to the specifications for CFC 600, as described in Annex 8. 2.4. Performance specification 2.4.1. When the heel of each foot is impacted at 4,4 ± 0,1 m/s in accordance with paragraph 2.3, the maximum impactor acceleration shall be 295 ± 50 g. 3. LOWER FOOT IMPACT TEST (WITH SHOE) 3.1. The objective of this test is to control the response of the Shoe and Hybrid III heel flesh and ankle joint to well- defined hard faced pendulum impacts. 3.2. The complete Hybrid III lower leg assembly, left (86-5001-001) and right (86-5001-002), equipped with the foot and ankle assembly, left (78051-614) and right (78051-615), shall be used, including the knee assembly. The load cell simulator (78051-319 Rev A) shall be used to secure the knee assembly (79051-16 Rev B) to the test fixture. The foot shall be fitted with the shoe specified in Annex 5, paragraph 2.9.2. 3.3. Test procedure 3.3.1. Each leg assembly shall be maintained (soaked) for four hours prior to the test at a temperature of 22 ± 3 °C and a relative humidity of 40 ± 30 per cent. The soak period shall not include the time required to reach steady state conditions.8.2.2018 EN Official Journal of the European Union L 35/47 3.3.2. Clean the impact surface of the underside of the shoe with a clean cloth and the impactor face with isopropyl alcohol or equivalent prior to the test. Check that there is no visible damage to the energy absorbing insert to the heel. 3.3.3. Align the impactor accelerometer with its sensitive axis parallel to the impactor longitudinal centre line. 3.3.4. Mount the leg assembly to the fixture shown in Figure 3 of this annex. The test fixture shall be rigidly secured to prevent movement during impact. The centre line of the femur load cell simulator (78051-319) shall be vertical with a tolerance of ± 0,5°. Adjust the mount such that the line joining the knee clevis joint and the ankle attachment bolt is horizontal with a tolerance of ± 3°, with the heel of the shoe resting on two sheets of a flat low friction (PTFE sheet) surface. Ensure that the tibia flesh is located fully towards the knee end of the tibia. Adjust the ankle such that a plane in contact with the heel and sole of the underside of the shoe is vertical and perpendicular to the direction of impact with a tolerance of ± 3° and such that the mid sagittal plane of the foot and shoe is aligned with the pendulum arm. Adjust the knee joint to 1,5 ± 0,5 g range before each test. Adjust the ankle joint so that it is free and then tighten just sufficiently to keep the foot stable on the PTFE sheet. 3.3.5. The rigid impactor comprises a horizontal cylinder diameter 50 ± 2 mm and a pendulum support arm diameter 19 ± 1 mm (Figure 4 of this annex). The cylinder has a mass of 1,25 ± 0,02 kg including instrumentation and any part of the support arm within the cylinder. The pendulum arm has a mass of 285 ± 5 g. The mass of any rotating part of the axle to which the support arm is attached should not be greater than 100 g. The length between the central horizontal axis of the impactor cylinder and the axis of rotation of the whole pendulum shall be 1 250 ± 1 mm. The impact cylinder is mounted with its longitudinal axis horizontal and perpendicular to the direction of impact. The pendulum shall impact the heel of the shoe in a horizontal plane which is a distance of 62 ± 2 mm above the base of the dummy heel when the shoe is resting on the rigid horizontal platform, so that the longitudinal centreline of the pendulum arm falls within 1 degree of a vertical line at impact. The impactor shall be guided to exclude significant lateral, vertical or rotational movement. 3.3.6. Allow a period of at least 30 minutes between successive tests on the same leg. 3.3.7. The data acquisition system, including transducers, shall conform to the specifications for CFC 600, as described in Annex 8. 3.4. Performance specification 3.4.1. When the heel of the shoe is impacted at 6,7 ± 0,1 m/s in accordance with paragraph 3.3 above, the maximum Tibia compressive force (F) shall be 3,3 ± 0,5 kN. z Figure 1 Upper foot impact test Test set-up specificationsL 35/48 EN Official Journal of the European Union 8.2.2018 Figure 2 Lower foot impact test (without shoe) Test set-up specifications Figure 3 Lower foot impact test (with shoe) Test set-up specifications8.2.2018 EN Official Journal of the European Union L 35/49 Figure 4 Pendulum impactorL 35/50 EN Official Journal of the European Union 8.2.2018 ANNEX 11 Test procedures for the protection of the occupants of vehicles operating on electrical power from high voltage and electrolyte spillage This annex describes test procedures to demonstrate compliance to the electrical safety requirements of paragraph 5.2.8 of this Regulation. For example, megohmmeter or oscilloscope measurements are an appropriate alternative to the procedure described below for measuring isolation resistance. In this case it may be necessary to deactivate the on-board isolation resistance monitoring system. Before the vehicle impact test conducted, the high voltage bus voltage (Vb) (see Figure 1 below) shall be measured and recorded to confirm that it is within the operating voltage of the vehicle as specified by the vehicle manufacturer. 1. TEST SETUP AND EQUIPMENT If a high voltage disconnect function is used, measurements are to be taken from both sides of the device performing the disconnect function. However, if the high voltage disconnect is integral to the REESS or the energy conversion system and the high- voltage bus of the REESS or the energy conversion system is protected according to protection degree IPXXB following the impact test, measurements may only be taken between the device performing the disconnect function and the electrical loads. The voltmeter used in this test shall measure DC values and have an internal resistance of at least 10 ΜΩ. 2. THE FOLLOWING INSTRUCTIONS MAY BE USED IF VOLTAGE IS MEASURED. After the impact test, determine the high voltage bus voltages (V, V , V ) (see Figure 1 below). b 1 2 The voltage measurement shall be made not earlier than 5 seconds, but, not later than 60 seconds after the impact. This procedure is not applicable if the test is performed under the condition where the electric power train is not energized. Figure 1 Measurement of V , V , V b 1 28.2.2018 EN Official Journal of the European Union L 35/51 3. ASSESSMENT PROCEDURE FOR LOW ELECTRICAL ENERGY Prior to the impact a switch S and a known discharge resistor R is connected in parallel to the relevant capacitor 1 e (ref. Figure 2 below). Not earlier than 5 seconds and not later than 60 seconds after the impact the switch S shall be closed while the 1 voltage V and the current I are measured and recorded. The product of the voltage V and the current I shall be b e b e integrated over the period of time, starting from the moment when the switch S is closed (t) until the voltage V 1 c b falls below the high voltage threshold of 60 V DC (t ). The resulting integration equals the total energy (TE) in h joules. (a) TE¼ƒth V �Idt tc b e When V is measured at a point in time between 5 seconds and 60 seconds after the impact and the b capacitance of the X-capacitors (C) is specified by the manufacturer, total energy (TE) shall be calculated x according to the following formula: (b) TE = 0,5 × C × (V2 – 3 600) x b When V and V (see Figure 1 above) are measured at a point in time between 5 seconds and 60 seconds after 1 2 the impact and the capacitances of the Y-capacitors (C , C ) are specified by the manufacturer, total energy y1 y2 (TE , TE ) shall be calculated according to the following formulas: y1 y2 (c) TE = 0,5 × C × (V 2 – 3 600) y1 y1 1 TE = 0,5 × C × (V 2 – 3 600) y2 y2 2 This procedure is not applicable if the test is performed under the condition where the electric power train is not energized. Figure 2 E.g. measurement of high voltage bus energy stored in X-capacitorsL 35/52 EN Official Journal of the European Union 8.2.2018 4. PHYSICAL PROTECTION Following the vehicle impact test any parts surrounding the high voltage components shall be, without the use of tools, opened, disassembled or removed. All remaining surrounding parts shall be considered part of the physical protection. The jointed test finger described in Figure 1 of Appendix 1 shall be inserted into any gaps or openings of the physical protection with a test force of 10 N ± 10 per cent for electrical safety assessment. If partial or full penetration into the physical protection by the jointed test finger occurs, the jointed test finger shall be placed in every position as specified below. Starting from the straight position, both joints of the test finger shall be rotated progressively through an angle of up to 90 degrees with respect to the axis of the adjoining section of the finger and shall be placed in every possible position. Internal electrical protection barriers are considered part of the enclosure If appropriate a low-voltage supply (of not less than 40 V and not more than 50 V) in series with a suitable lamp should be connected, between the jointed test finger and high voltage live parts inside the electrical protection barrier or enclosure. 4.1. Acceptance conditions The requirements of paragraph 5.2.8.1.3 of this Regulation shall be considered to be met if the jointed test finger described in figure 1 of Appendix 1, is unable to contact high voltage live parts. If necessary a mirror or a fiberscope may be used in order to inspect whether the jointed test finger touches the high voltage buses. If this requirement is verified by a signal circuit between the jointed test finger and high voltage live parts, the lamp shall not light. 5. ISOLATION RESISTANCE The isolation resistance between the high voltage bus and the electrical chassis may be demonstrated either by measurement or by a combination of measurement and calculation. The following instructions should be used if the isolation resistance is demonstrated by measurement. Measure and record the voltage (V) between the negative and the positive side of the high voltage bus (see Figure 1 b above); Measure and record the voltage (V ) between the negative side of the high voltage bus and the electrical chassis (see 1 Figure 1 above); Measure and record the voltage (V ) between the positive side of the high voltage bus and the electrical chassis (see 2 Figure 1 above); If V is greater than or equal to V , insert a standard known resistance (R) between the negative side of the high 1 2 o voltage bus and the electrical chassis. With R installed, measure the voltage (V ') between the negative side of the o 1 high voltage bus and the vehicle electrical chassis (see Figure 3 below). Calculate the isolation resistance (R) i according to the formula shown below. R = R * (V/V ' – V/V ) or R = R * V * (1/V ' – 1/V ) i o b 1 b 1 i o b 1 1 Divide the result R, which is the electrical isolation resistance value in ohm (Ω), by the working voltage of the high i voltage bus in volt (V). R (Ω/V) = R (Ω)/Working voltage (V) i i8.2.2018 EN Official Journal of the European Union L 35/53 Figure 3 Measurement of V ' 1 If V is greater than V , insert a standard known resistance (R) between the positive side of the high voltage bus 2 1 o and the electrical chassis. With R installed, measure the voltage (V ') between the positive side of the high voltage o 2 bus and the electrical chassis (see Figure 4 below). Calculate the isolation resistance (Ri) according to the formula shown below. R = R * (V/V ' – V/V ) or R = R * V * (1/V ' – 1/V ) i o b 2 b 2 i o b 2 2 Divide the result R, which is the electrical isolation resistance value in ohm (Ω), by the working voltage of the high i voltage bus in volt (V). R (Ω/V) = R (Ω)/Working voltage (V) i iL 35/54 EN Official Journal of the European Union 8.2.2018 Figure 4 Measurement of V ' 2 Note: The standard known resistance R (in Ω) should be the value of the minimum required isolation resistance o (Ω/V) multiplied by the working voltage (V) of the vehicle plus/minus 20 per cent. R is not required to be precisely o this value since the equations are valid for any R; however, a R value in this range should provide a good o o resolution for the voltage measurements. 6. ELECTROLYTE SPILLAGE Appropriate coating shall be applied, if necessary, to the physical protection in order to confirm any electrolyte leakage from the REESS after the impact test. Unless the manufacturer provides means to differentiate between the leakage of different liquids, all liquid leakage shall be considered as the electrolyte. 7. REESS RETENTION Compliance shall be determined by visual inspection.8.2.2018 EN Official Journal of the European Union L 35/55 APPENDIX JOINTED TEST FINGER (DEGREE IPXXB) Figure 1 Jointed test finger Material: metal, except where otherwise specified Linear dimensions in millimetres Tolerances on dimensions without specific tolerance: (a) On angles: 0/– 10° (b) On linear dimensions: up to 25 mm: 0/– 0,05 mm over 25 mm: ± 0,2 mm Both joints shall permit movement in the same plane and the same direction through an angle of 90° with a 0 to + 10° tolerance.