Home India Ministry of Environment, Forest and Climate Change Notification on Environmental Standards for pesticide indust...
Date: 2025-07-22 Category: Extra Ordinary State: Union Government Country: India

Notification on Environmental Standards for pesticide industry.

Issued by Ministry of Environment, Forest and Climate Change · Control of Pollution Division

Research with AI Agent Chat with Document Generate Summary Translate Helpful Share Add to Project Create Task

Executive Summary & Key Takeaways

Executive Summary: This notification amends the Environment Protection Rules of 1986, specifically concerning pesticide effluent and emission standards. It was issued by the Ministry of Environment, Forest and Climate Change and went into effect on July 22, 2025. The amendment introduces revised standards for pesticide industries, including effluent limits, emission standards, and incinerator requirements. Key Points / Main Content: Effluent Standards for Pesticide Industry: * COD limit: 250 mg/l for technical grade units and 150 mg/l for formulation grade units. * BOD limit: 30 mg/l for both formulation and technical grade units. * pH range: 6.5-8.5. * Specific limits for Oil and Grease (10 mg/l), Suspended Solids (100 mg/l), and Bioassay Test (90% survival). * Additional parameters include limits for Cyanide, Arsenic, Copper, Manganese, Mercury, Antimony, Zinc, Nickel, Nitrate, Phosphate, Phenol, Sulphur, Benzene Hexachloride, Carbonyl, Copper Sulphate, Copper Oxychloride, DDT, Dimethoate, 2,4 D, Endosulfan, Fenitothrion, Malathion, Methyl Parathion, Paraquat, Phenathoate, Phorate, Proponil, Pyrethrums, Ziram, and other pesticides. * Bioassay Test as per IS: 6582-1971. * These standards are not applicable to industries discharging to Common Effluent Treatment Plants, but shall be applicable to all discharge to land and surface water bodies including use of treated wastewater for horticulture or irrigation purpose. * State Pollution Control Boards to prescribe limits for Total Dissolved Solids, Sulphates, and Chlorides. Emission Standards: * Limits specified for various compounds, including HCl, Chlorine, Hydrogen Sulphide, Ammonia, Phosphorus pentoxide, Chloromethane, Hydrogen Bromide, Pesticides particulate matter, Benzene, Toluene, Xylene, Acetonitrile, Dichloromethane, Acetone, and Methanol. * Total cumulative solvent losses should not exceed 5% annually. Incinerator Standards: * Limits for Particulate Matter, HCl, Sulphur Dioxide, Carbon Monoxide, Total organic Carbon, and Total Dioxins and Furans. * Requirements for oxygen correction, minimum temperatures (950°C - 1100°C depending on waste type and technology), and gas residence time in incinerators. * Scrubbers should not be used as quenchers. * TOC content in incineration ash and residue should be less than 3%, with loss on ignition less than 5%. * Incinerators must have a chimney of at least 30 meters height. * Effluent from scrubbers must comply with effluent standards. Storm Water: * Storm water should be channelized through separate drains passing through a High Density Polyethylene lined pit having holding capacity of 10 minutes hourly average of rainfall. Impact Analysis: Pesticide Manufacturers: * Impact: Must comply with the new, more stringent effluent and emission standards. * Action Required: Upgrade or modify existing treatment processes to meet the revised standards, conduct regular monitoring, and report compliance. State Pollution Control Boards/Pollution Control Committees: * Impact: Responsible for enforcing the revised standards and prescribing limits for Total Dissolved Solids, Sulphates, and Chlorides. * Action Required: Implement monitoring programs, conduct inspections, and ensure compliance by pesticide manufacturers. Common Effluent Treatment Plants (CETPs): * Impact: Effluent standards are not applicable to industries discharging to CETPs. * Action Required: Ensure proper treatment of wastewater received from industries and comply with their discharge standards. General Public/Environment: * Impact: Benefits from reduced pollution and improved environmental quality due to stricter regulations on pesticide manufacturing. * Action Required: Stay informed about environmental regulations and report any violations to relevant authorities.

Key Entities Referenced

New Delhi: The city where the notification was issued. Environment Protection Rules, 1986: The principal rules being amended by this notification. Environment Protection Act, 1986: The Act that confers powers to the Central Government to make rules for environment protection. Ministry of Environment, Forest and Climate Change: The Indian government ministry responsible for publishing the notification and amending the rules. Central Government: The governing authority enacting the amendments to the Environment Protection Rules. The Gazette of India: The official government publication in which the notification is published. Environment Protection Sixth Amendment Rules, 2025: The name given to the new set of rules. State Pollution Control Board: State level organisation which will prescribe limits of Total Dissolved Solids, Sulphates and Chlorides.
Official Source Record View Original Source →
See Full Document Text
रजिस्ट्री स.ं डी.एल.- 33004/99 REGD. No. D. L.-33004/99 xxxGIDHxxx ससीी..जजीी..--डडीी..एएललxx..x--GअअID..--E22x44xx00 7722002255--226644992266 CCGG--DDLL--EE--2244007722002255--226644992266 असाधारण EXTRAORDINARY भाग II—खण् ड 3—उप-खण्ड (i) PART II—Section 3—Sub-section (i) प्राजधकार स ेप्रकाजित PUBLISHED BY AUTHORITY स.ं 444] नई दिल्ली, मगं लवार , िुलाई 22, 2025/आषाढ़ 31, 1947 No. 444] NEW DELHI, TUESDAY , JULY 22, 2025/ ASHADHA 31, 1947 पर्ावा रण, वन एव ं िलवार् ु पररवतना मत्रं ालर् अजधसचू ना नई दिल्ली, 22 िुलाई, 2025 सा.का.जन. 487(अ).-– पर्ावा रण (संरक्षण) जनर्म, 1986 का संिोधन करने के जलए कजतपर् जनर्मों का प्रारूप, भारत सरकार के पर्ाावरण, वन और िलवार्ु पररवतान मंत्रालर् की अजधसूचना संखर्ांक सा.का.जन. 753(अ), तारीख 17 अक्टूबर, 2023 द्वारा भारत के रािपत्र, असाधारण, भाग 2, खडं 3, उपखंड (i) में तारीख 18 अक्टूबर, 2023 को प्रकाजित दकर्ा गर्ा था, जिसमें सभी व् र्जक्त र्ों स,े जिनके उसके द्वारा प्रभाजवत होन े की संभावना थी, आक्षपे और सुझाव उस तारीख से, जिसको उक्त अजधसूचना को अन्तर्वाष्ट करने वाले रािपत्र की प्रजतर्ां िनसाधारण को उपलब्ध करा िी गई थी, साठ दिन की अवजध के समाप्त होन े से पूवा आमंजत्रत दकए गए थे; और उक्त रािपजत्रत अजधसूचना की प्रजत िनसाधारण को तारीख 18 अक्टूबर, 2023 को उपलब्ध करा िी गई थी; और, पूवोक्त अजधसूचना के प्रजतउत् तर म ें सभी व् र्जक्त र्ों और पणधाररर्ों से प्राप् त आक्षपे ों और सुझावों पर केंद्रीर् सरकार द्वारा सम् र्क रुप से जवचार दकर्ा गर्ा; 4899 GI/2025 (1)2 THE GAZETTE OF INDIA : EXTRAORDINARY [PART II—SEC. 3(i)] अतः, अब, केंद्रीर् सरकार, पर्ाावरण (संरक्षण) अजधजनर्म, 1986 (1986 का 29) की धारा 6 और धारा 25 द्वारा प्रित्त िजक्तर्ों का प्रर्ोग करते हुए, पर्ाावरण (सरं क्षण) जनर्म, 1986 का और सिं ोधन करने के जलए जनम्नजलजखत जनर्म बनाती ह,ै अथाात:् - 1. संजक्षप्त नाम और प्रारंभ.- (1) इन जनर्मों का संजक्षप्त नाम पर्ाावरण (सरं क्षण) छठा संिोधन जनर्म, 2025 ह।ै (2) र् ेरािपत्र में इनके प्रकािन की तारीख को प्रवृत्त होंगे। 2. पर्ाावरण (संरक्षण) जनर्म, 1986 की अनुसूची-I म ें क्रम संखर्ा 40 और उससे संबजं धत प्रजवजष्टर्ों के स्ट्थान पर जनम्नजलजखत क्रम संखर्ा और प्रजवजष्टर्ां रखी िाएंगी, अथाात:् - क्र.स.ं उद्योग मानिंड मानक “40 कीटनािक बजहस्राव मानक उद्योग पीएच और बार्ो एस्ट्से परीक्षण को छोड़कर, जम.ग्रा./ली. म ेंसान्द्रता को सीजमत करना क. अजनवार् ामानिंड सीओडी तकनीकी ग्रडे इकाइर्ों और उन इकाइर्ों के जलए िहां एक ही पररसर में प्रजतपािन कार्ाकलापों के साथ-साथ तकनीकी ग्रडे उत्पािन होता ह,ै के जलए 250 प्रजतपािन ग्रेड इकाइर्ों के जलए 150 बीओडी (3 दिन 27 °C) 30 (प्रजतपािन इकाइर्ों के साथ-साथ तकनीकी ग्रडे इकाइर्ों िोनों के जलए) पीएच (pH) 6.5-8.5 ऑइल और ग्रीस 10 प्लवमान ठोस पिाथ ा 100 *बार्ोएस्ट्से परीक्षण 100% बजहस्राब में 96 घंटों के बाि मछली की 90% उत्तरिीजवता ख. अजतररक्त मानिडं साइनाइड CN के रूप म ें 0.1 As के रूप म ेंआसेजनक 0.1 तांबा 1.0 मैंगनीि 1.0 पारा 0.01 ऐजन्टमनी (Sb के रूप में) 0.1 िस्ट्ता 1.0 जनकल, आदि (भारी धातुएँ व्यजष्टक रूप म)ें बीआईएस के अनुसार पेर्िल मानकों से[भाग II—खण् ड 3(i)] भारत का रािपत्र : असाधारण 3 व्यजष्टक रूप में 5 गुन े से अजधक नहीं होना चाजहए नाइरेट (NO3 के रूप में) 50 फॉस्ट्फेट (P के रूप में) 5.0 दफनोल और फेनोजलक र्ौजगक C6H5OH के 1.0 रूप म ें गंधक 0.03 बेंिीन हक्े साक्लोराइड (बीएचसी) 0.01 काबाजनल 0.01 कॉपर सल्फेट 0.05 कॉपर ऑक्सीक्लोराइड 9.6 डीडीटी 0.01 डाइमेथोएट 0.45 2,4 D 0.4 एंडोसल्फान 0.01 फेजनटोजिर्ोन 0.01 मेलोजथर्ान 0.01 जमथाइल पैराजथर्ान 0.01 पैराकाट 2.3 फेनाथोएट 0.01 फोरेट 0.01 प्रोपोजनल 7.3 पाइरेिम्स 0.01 जिरम 1.0 अन्र् कीटनािक (व्यजष्टक रूप में) 0.10 *बार्ोएस्ट्से परीक्षण IS: 6582-1971 के अनुसार दकर्ा िाएगा। रटप्पणी : 1. सामूजहक बजहःस्राव िोधन संर्ंत्र (सीईटीपी) में जवसर्िात करने वाल े उद्योग पर लागू नहीं ह,ै और बागबानी र्ा ससंचाई उिेश्र्ों के जलए िोजधत अपजिष्ट िल के उपर्ोग सजहत भूजम और सतही िल स्रोतों में दकए िाने वाले सभी जवसिानों पर लागू होगा। 2. संबंजधत राज्र् प्रिषू ण जनर्त्रं ण बोडा/ प्रिषू ण जनर्ंत्रण सजमजत अनुप्रवाह में प्रापक िल जनकार् के उपर्ोग के आधार पर कुल घलु निील ठोस कण (टीडीएस), सल्फेट्स और क्लोराइड की सीमा जनधााररत करेगी, जिसमें बजहःस्राव का जनपटान दकर्ा िाएगा।4 THE GAZETTE OF INDIA : EXTRAORDINARY [PART II—SEC. 3(i)] 3."अजतररक्त मानिंडों" के रूप में सूचीबद्ध मानिंडों को मामले िर मामल े के आधार पर प्रदक्रर्ा और उत्पाि पर जनभार करते हुए जनधााररत दकर्ा िाएगा। ग. उत्सिना मानक सीजमत साद्रं ता mg/Nm³ म ें HCI 20 Cl 5 2 H S 5 2 NH 30 3 P O 10 2 5 CH CI 20 3 HBr 5 जवजवक्त कण के रूप म ेंकीटनािक र्ौजगक 20 बेंिीन 5 टोल्र्ूजन 100 ज़ाइलीन 100 एसीटोनाराइल 1000 डाईक्लोरोजमथने 200 एसीटोन 2000 जमथेनॉल 350 जवलार्क* की कुल संचर्ी हाजन भंडारण सूची से वार्षाक आधार पर जवलार्क के 5 प्रजतित से अजधक नहीं होनी चाजहए * जवलार्क की हाजन स ेजवलार्क को गैसीर्, रूम में उत्सिान और अपजिष्ट िल में छोड़ना अजभप्रेत ह।ै घ. भस्ट्मकों के जलए उत्सिना मानक िब तक जनर्िाष्ट न नमूने लेन े की अवजध दकर्ा िाए, सांद्रता को (जमनटों में) िब तक जनर्िाष्ट न दकर्ा िाए जम.ग्रा./ घनमीटर 3 म ें सीजमत करना जवजवक्त कण 50 30 र्ा अजधक (300 लीटर उत्सिान के नमून े के जलए) HCI 50 30 SO 200 30 2 CO 100 िैजनक औसत कुल िैजवक काबान 20 30 कुल डाइऑजक्सन और फ्र्ूरान 0.1 ngTEQ/Nm³ 8घण्टे[भाग II—खण् ड 3(i)] भारत का रािपत्र : असाधारण 5 (मौिूिा/नर्ा भस्ट्मक) Sb+As+Pb+Cr+Co+Cu+Mn+Ni+V 1.5 2 घण्टे और उनके र्ौजगक रटप्पणी : (i)सभी मानीटर दकए गए मान को िुष्क आधार पर 11% ऑक्सीिन तक सही दकर्ा िाएगा। (ii) टेल गैस में CO की सांद्रता 7% से कम नहीं होगी। 2 (iii) र्दि हलै ोिेनेटेड काबाजनक अपजिष्ट का विन इनपुट अपजिष्ट के जहसाब से 1% स े कम ह,ै तो एकल कक्ष भस्ट्मक म ें सभी सुजवधाएं इस प्रकार से बनाई िाएगं ी दक भस्ट्मक में न्र्नू तम तापमान 1100°C प्राप्त दकर्ा िा सके। द्रवीकृत बेड प्रौद्योजगकी आधाररत भस्ट्मक के जलए, तापमान 950°C पर बनाए रखा िाएगा। (iv) र्दि हलै ोिेनेटेड काबाजनक अपजिष्ट का विन इनपुट अपजिष्ट के जहसाब से 1% स े अजधक ह,ै तो अपजिष्ट को केवल रटवन चैम्बर भस्ट्मक म ें िलार्ा िाएगा और सभी सुजवधा संर्ंत्रों को प्राथजमक कक्ष म ें 850±25°C और जद्वतीर्क िहन कक्ष म ें 1100°C का न्र्ूनतम तापमान प्राप्त करने के जलए बनार्ा िाएगा और जद्वतीर्क िहन कक्ष में गसै मौिूिगी समर् िो सेकंड से कम नहीं होना चाजहए। (v) स्ट्क्रसबंग उत्सिान के जलए बने स्ट्क्रबर का उपर्ोग िमनकताा के रूप म ेंनहीं दकर्ा िाएगा। (vi) भस्ट्मीकरण संर्ंत्रों (िहन कक्षों) को ऐसे तापमान, अवधारण समर् और वार्ुमण्डलीर् जवक्षोप के साथ संचाजलत दकर्ा िाएगा, तादक भस्ट्मीकरण भस्ट्म और अवजिष्टों में कुल काबाजनक काबान (टीओसी) सामग्री 3% से कम हो और िहन करन े पर उनका नुकसान सूख े विन का 5% से कम हो। मानकों को पूरा न करने की जस्ट्थजत में, र्थाजस्ट्थजत, भस्ट्म और अवजिष्ट को पनु ः िला दिर्ा िाएगा। (vii) भस्ट्मक म ेंकम स ेकम तीस मीटर ऊंची जचमनी होनी चाजहए। ड. भस्ट्मक स ेउत्पन्न बजहःस्राव रटप्पणी : (i). स्ट्क्रबर और फिा की धलु ाई से उत्पन्न बजहःस्राव बंि नाली र्ा पाइपों के माध्र्म से प्रवाजहत दकर्ा िाएगा और पर्ाावरण (संरक्षण) जनर्म, 1986 के अधीन अजधसूजचत पर्ाावरण प्रिषू ण (भाग कः बजहःस्राव) के जवसिान के जलए सामान्र् मानकों की अनुसूची: VI के साथ परठत ऊपर 'ख' म ेंउजल्लजखत बजहःस्राव मानकों का अनपु ालन करन े के जलए उपचाररत दकर्ा िाएगा। (ii). अपजिष्ट िल र्ा फि ा धोन े स े बनन े वाला कुल घलु निील ठोस कण (टीडीएस) उपर्ोग दकए गए अिोजधत पानी के (टीडीएस) से 1000 जमलीग्राम/लीटर से अजधक नहीं होना चाजहए। च. तफू ान का पानी रटप्पणी : (i). तूफान के पानी को स्ट्क्रबर पानी और/र्ा फिा धोन े के पानी के साथ जमजित होने की अनमु जत िी िाएगी। (ii). तूफान के पानी को 10 जमनट (प्रजत घंटा औसत) वषाा िल धारण क्षमता की एचडीपीई लाइन गड्ढे से गुिरने वाली अलग-अलग नाजलर्ों के माध्र्म से प्रवाजहत दकर्ा िाएगा।”6 THE GAZETTE OF INDIA : EXTRAORDINARY [PART II—SEC. 3(i)] [फा.सं.क्र्ू-15017/06/2019-सीपीडब्ल्र्ू] नीलेि कुमार साह, संर्ुक्त सजचव रटप्पणी : मलू जनर्म भारत के रािपत्र, असाधारण, भाग ॥, खंड 3, उप-खंड (i) में संखर्ांक का.आ. 844 (अ) तारीख 19 नवम्बर, 1986 द्वारा प्रकाजित दकए गए थ े और अंजतम बार सा.का.जन. 482(अ) तारीख 21 िुलाई, 2025 द्वारा संिोजधत दकए गए। MINISTRY OF ENVIRONMENT, FOREST AND CLIMATE CHANGE NOTIFICATION New Delhi, the 22nd July, 2025 G.S.R. 487(E).—Whereas, the draft of certain rules further to amend the Environment (Protection) Rules, 1986 were published, vide notification of the Government of India in the Ministry of Environment, Forest and Climate Change, number, G.S.R. 753(E), dated 17th October, 2023, in the Gazette of India, Extraordinary, Part II, Section 3, Sub-section (i), dated the 18th October, 2023, inviting objections or suggestions from all persons likely to be affected thereby before the expiry of a period of sixty days from the date on which copies of the Gazette containing the said notifications were made available to the public; And whereas, the copy of the said Gazette notification was made available to the public on the 18th October, 2023; And Whereas, objections and suggestions received from all persons and stakeholders in response to the aforesaid notification have been duly considered by the Central Government; Now, therefore, in exercise of the powers conferred by sections 6 and 25 of the Environment (Protection) Act, 1986 (29 of 1986), the Central Government hereby makes the following rules further to amend the Environment (Protection) Rules, 1986, namely: - 1. Short title and commencement.—(1) These rules may be called the Environment (Protection) Sixth Amendment Rules, 2025. (2) They shall come into force on the date of their publication in the Official Gazette. 2. In the Environment (Protection) Rules, 1986, in Schedule-l, for serial number 40 and the entries relating thereto, the following serial number and entries shall be substituted, namely:- S. Industry Parameter Standards No. “40 Pesticide Effluent Standards Industry Limiting concentration in mg/l, except for pH and Bioassay test A. Compulsary Parameters 250 for technical grade units and for those units where formulation activities as well as technical COD grade production in the same premises[भाग II—खण् ड 3(i)] भारत का रािपत्र : असाधारण 7 150 for formulation grade units 30 ( for both formulation units as well as technical BOD (3 days 270C) grade units) pH 6.5-8.5 Oil and Grease 10 Suspended Solids 100 *Bioassay Test 90% survival of fish after 96 hours in 100% effluent B. Additional Parameters Cyanide as CN 0.1 Arsenic as As 0.1 Copper 1.0 Manganese 1.0 Mercury 0.01 Antimony (as Sb) 0.1 Zinc 1.0 Nickel, etc. (heavy metals Shall not exceed individually 5 times the drinking individually) water standards as per BIS Nitrate (as NO3) 50 Phosphate (as P) 5.0 Phenol & Phenolic Compounds as 1.0 C6H5OH Sulphur 0.03 Benzene Hexachloride (BHC) 0.01 Carbonyl 0.01 Copper Sulphate 0.05 Copper Oxychloride 9.6 DDT 0.01 Dimethoate 0.45 2,4 D 0.4 Endosulfan 0.01 Fenitothrion 0.01 Malathion 0.01 Methyl Parathion 0.01 Paraquat 2.3 Phenathoate 0.01 Phorate 0.01 Proponil 7.3 Pyrethrums 0.01 Ziram 1.0 Other Pesticide (individually) 0.10 *Bioassay Test shall be carried out as per IS: 6582-1971. Note: 1. Not applicable to industry discharging to Common Effluent Treatment Plants, and shall be applicable to all discharge to land and surface water bodies including use of treated wastewater for horticulture or irrigation purpose. 2. The concerned State Pollution Control Board or Pollution Control Committee shall prescribe limits of Total Dissolved Solids, Sulphates and Chlorides depending on the usages of recipient water body in downstream, in which effluent shall be disposed off.8 THE GAZETTE OF INDIA : EXTRAORDINARY [PART II—SEC. 3(i)] 3. Parameters listed as “Additional Parameters” shall be prescribed depending upon the process and product, on a case to case basis. C. Emission Standards Limiting concentration in mg/Nm3 HCl 20 Cl 5 2 H S 5 2 NH 30 3 P O 10 2 5 CH Cl 20 3 HBr 5 Pesticides compounds in the form of 20 particulate matter Benzene 5 Toluene 100 Xylene 100 Acetonitrile 1000 Dichloromethane 200 Acetone 2000 Methanol 350 The total cumulative losses of solvent* should not be more than 5 percent of the solvent on annual basis from storage inventory *Losses of solvent means the solvent leaving in gaseous emissions and wastewater. D. Emission Standards for Incinerator Limiting Concentration Sampling durations in mg/Nm3, unless stated in(minutes) unless stated Particulate Matter 50 30 or more (for sampling of 300 litres of emission) HCl 50 30 SO 200 30 2 CO 100 Daily average Total organic Carbon 20 30 Total Dioxins and Furans (Existing or 0.1 ngTEQ/Nm3 8 hours New Incinerator) Sb+As+Pb+Cr+Co+Cu+Mn+Ni+V 1.5 2 hours and their compounds Note: (i) All monitored value shall be corrected to 11% oxygen on dry basis. (ii) The CO concentration in tail gas shall not be less than 7%. 2 (iii) In case, halogenated organic waste is less than 1% by weight input waste, all the facilities in single chamber incinerators shall be designed so as to achieve a minimum temperature of 1100oC in the incinerator. For fluidized bed technology based incinerator, temperature shall be maintained at 950oC.[भाग II—खण् ड 3(i)] भारत का रािपत्र : असाधारण 9 (iv) In case halogenated organic waste is more than 1% by weight in input waste, waste shall be incinerated only in twin chamber incinerators and all the facilities shall be designed to achieve a minimum temperature of 850±25oC in primary chamber and 1100oC in secondary combustion chamber with a gas residence time in secondary combustion chamber not less than two seconds. (v) Scrubber meant for scrubbing emissions shall not be used as quencher. (vi) Incineration plants shall be operated (combustion chambers) with such temperature, retention time and turbulence, as to achieve Total Organic Carbon (TOC) content in the incineration ash and residue less than 3% and their loss on ignition is less than 5% of the dry weight. In case of nonconformity, ash and residue as the case may be, shall be re-incinerated. (vii) The incinerator shall have a chimney of at least thirty meters height. E. Effluent from Incinerator Note: (i) Effluent from scrubber(s) and floor washings shall flow through closed conduit or pipe network and be treated to comply with the effluent standards mentioned at ‘B’ above read with Schedule VI: General Standards for Discharge of Environment Pollutions (Part A : Effluents) notified under the Environment (Protection) Rules, 1986. (ii) The build-up in Total Dissolved Solids in wastewater or floor washings shall not exceed 1000 mg/l over and above the Total Dissolved Solids of raw water used. F. Storm water Note: (i) Storm water shall be allowed to mix with scrubber water and/or floor washings. (ii) Storm water shall be channelized through separate drains passing through a High Density Polyethylene lined pit having holding capacity of 10 minutes (hourly average) of rainfall.” [F. No. Q-15017/06/2019-CPW] NEELESH KUMAR SAH, Jt Secy. Note : The principle rules were published in the Gazette of India, Extraordinary, Part II, Section 3, Sub-section (i), vide number S.O.844(E), dated the 19th November, 1986 and last amended vide G.S.R. 482(E), dated 21st July, 2025. Uploaded by Dte. of Printing at Government of India Press, Ring Road, Mayapuri, New Delhi-110064 and Published by the Controller of Publications, Delhi-110054.

Continue your research