Home India Ministry of Commerce and Industry Whereas certain draft regulations further to amend the India...
Date: 2020-09-11 Category: Extra Ordinary State: Union Government Country: India

Whereas certain draft regulations further to amend the Indian Boiler Regulations, 1950 were published as required under sub section 1 of section 31 of the Boilers Act 1923 5 of 1923 vide notification of the Government of India

Issued by Ministry of Commerce and Industry · DEPARTMENT FOR PROMOTION OF INDUSTRY AND INTERNAL TRADE

Research with AI Agent Chat with Document Generate Summary Translate Helpful Share Add to Project Create Task

Executive Summary & Key Takeaways

Executive Summary: This notification details amendments to the Indian Boiler Regulations, 1950, under the Boilers Act of 1923. These amendments, effective from the date of publication in the Official Gazette, address the acceptance of steel grades, recognition of competent authorities, and inspection fees, among other changes. The notification follows a period of public comment ending June 6, 2020, during which no objections were received. Key Points / Main Content: Steel Grade Acceptance: * Until 33,000-hour tests are completed by specified labs, steel may be accepted under ASME, BS, or EN codes, subject to certain conditions. * Steel producer must furnish a certificate confirming manufacturing is strictly in accordance with ASME, BS or EN codes. * Short-term stress-rupture tests for 1000 hours are to be carried out by specified labs. * Two 1000-hour creep rupture tests at 50°C above service temperature are required for each steel grade. * Forging used in valves shall be tested at 550°C for 1000 hours. Recognition of Authorities: * Firms applying for recognition as Competent Authority, Inspecting Authority, etc., must apply to the Secretary, Central Boilers Board. * The Evaluation or Appraisal Committee submits a report recommending grant or refusal of recognition to the Member-Secretary, Central Boiler Board. * The Member-Secretary may issue a certificate of recognition or inform the applicant in writing if recognition is refused. * Regulation 4F is omitted. * Firms unsatisfied with refusal reasons may appeal to the Chairperson, Central Boilers Board. Inspection and Testing: * A copy of the Memorandum of Inspection Book shall be obtained from the concerned boiler inspectorate and returned within one week of final inspection completion. * "Inspecting Authority" is substituted for "Chief Inspector" in regulation 5. * Hydraulic testing of chests and fittings is required at a minimum of 1.5 times the maximum allowable working pressure. Technical Specifications and Procedures: * Minimum wall thickness for wrought bends is determined by specified equations. * Revisions to permissible working pressure certification and provisional order issuance are outlined. * Inclusion of "Jammu and Kashmir" and "Ladakh" in the list of States and Union Territories. * Shell type waste heat boilers (unfired) require non-destructive testing by a Remnant Life Assessment Organisation after 25 years. * Life extension for waste heat boilers is subject to certain conditions and certifications. Fees and Forms: * Maximum fee for what prescribed in regulation 385A is Rs. 50,000. * Amendments to fees for Valves and Flanges inspection * Spares and boiler components inspection fee is based on surface area. * Tube and tubebends fee is Rs. 10 per meter, minimum Rs. 500. * Revised procedures for provisional order issuance are detailed. * Form I is updated regarding the requisite area of safety valves. Appendix JB (Waste Heat Boilers): * Revised guidelines for inspection and operation of waste heat boilers (fired and unfired) used in continuous process plants, based on age and inspection results. * Details on required operation records and shutdown procedures. * Remnant Life Assessment provisions for boilers over twenty years of age. Impact Analysis: Central Boilers Board: * Impact: Responsible for implementing and overseeing the amended regulations. * Action Required: Update procedures and communicate changes to relevant stakeholders. Boiler Manufacturers and Steel Producers: * Impact: Must comply with new steel grade acceptance criteria and provide necessary certifications. * Action Required: Implement quality control measures to meet ASME, BS, or EN code requirements and prepare required documentation. Inspecting Authorities, Competent Persons, and Remnant Life Assessment Organizations: * Impact: Affected by changes in recognition procedures, inspection requirements, and fee structures. * Action Required: Review updated regulations, adjust practices accordingly, and apply for recognition if necessary. Boiler Owners and Operators: * Impact: Subject to revised inspection schedules, testing requirements, and operational guidelines, particularly for waste heat boilers. * Action Required: Ensure compliance with updated regulations, schedule necessary inspections, and maintain required records.

Key Entities Referenced

Indian Boiler Regulations, 1950: A set of regulations pertaining to boilers in India, which is being amended by this notification. Boilers Act, 1923: Indian legislation governing boilers. Section 28 of this act confers powers to the Central Boilers Board, and Section 31 requires the publication of draft regulations. Central Boilers Board: A board responsible for making regulations regarding boilers in India. The notification is issued by the Secretary of this board. Ministry of Commerce and Industry: The ministry under which the Department for Promotion of Industry and Internal Trade and Central Boilers Board operate. Department for Promotion of Industry and Internal Trade: A department under the Ministry of Commerce and Industry involved in the amendment of the Indian Boiler Regulations. New Delhi: The city where the notification was issued. National Metallurgical Laboratory: A testing laboratory recognized by the Central Boilers Board for creep testing of alloy steel. Bharat Heavy Electricals Limited, Hyderabad: Corporate Research and Development Laboratory of Bharat Heavy Electricals Limited is a testing laboratory recognized by the Central Boilers Board for creep testing of alloy steel.
Official Source Record View Original Source →
See Full Document Text
रजिस्ट्री स.ं डी.एल.- 33004/99 REGD. NO. D. L.-33004/99 सी.जी.-डी.एल.-अ.-14092020-221710 xxxGIDHxxx CG-DL-E-14092020-221710 xxxGIDExxx असाधारण EXTRAORDINARY भाग II—खण्ड 3—उप-खण्ड (i) PART II—Section 3—Sub-section (i) प्राजधकार स ेप्रकाजित PUBLISHED BY AUTHORITY स.ं 445] नई दिल्ली, िक्रु वार, जसतम्र र 11, 2020/भार 20, 1942 No. 445] NEW DELHI, FRIDAY, SEPTEMBER 11, 2020/BHADRA 20, 1942 वाजणज्य रर उ्योगग ं्ं ालय (उ्योगग सवं धनध रर आतं ररक व्य ापार जवभाग) (केन्‍दर ीय र्यलस धरयोगड)ध अजधसचू ना नई दिल् ली, 11 जसतंरर, 2020 सा.का.जन. 551(अ).—कजतपय जवजनयंों का जनम्नजलजखत प्रारूप, भारतीय र्यलर जवजनयं, 1950 का संियोगधन करने के जलए, भारत के रािप्, असाधारण, भाग II, खंड 3, उप-खंड (i) ंें भारत सरकार, वाजणज्य रर उ्योगग ंं्ालय (उ्योगग संवधधन रर आंतररक व्यापार जवभाग), (केंरीय र्यलर रयोगडध) की तारीख 21 ंई, 2020 की अजधसूचना सा.का.जन. 343(अ) द्वारा, भारतीय र्यलर अजधजनयं, 1923 (1923 का 5) की धारा 31 उपधारा (1) द्वारा यथा अपेजित सभी संभाव्य प्रभाजवत व्यजियों से आपजियां रर सझु ाव ंांगे िाने के जलए प्रकाजित दकया गया था ियोग इन प्रारूप जनयंों की रािप् की प्रजतयां िनसाधारण िनता कयोग उपल्‍ ध कराए िाने से पतताजलस दिन की अवजध की संाजि के पश्चात उपल्‍ध कराया गया था; रर िरदक, उि अजधसूचना की प्रजतयां 6 िनू , 2020 कयोग िनता कयोग उपल्‍ध कराई गईं थीं; रर िरदक, उि प्रारूप जवजनयंों के संरंध ं ेंदकसी व्यजि से कयोगई आपजियां रर सुझाव प्राि नहीं हुए थे; 4234 GI/2020 (1)2 THE GAZETTE OF INDIA : EXTRAORDINARY [PART II—SEC. 3(i)] अत: अर, र्यलर अजधजनयं, 1923 (1923 का 5) की धारा 28 द्वारा प्रिि िजियों का प्रययोगग करते हुए, केंरीय र्यलसध रयोगडध, भारतीय र्यलर जवजनयं, 1950 कयोग रर सिं योगधन करने के जलए जनम्नजलजखत जवजनयं रनाता है, अथाधत ्- 1. सजं िप्त नां रर प्रारंम्भ .-(1) इन जवजनयंों का संजिि नां भारतीय र्यलर (िसू रा संियोगधन) जवजनयं,2020 ह।ै (2) य ेरािप् ंें उनके प्रकािन की तारीख कयोग प्रवृि होंगे। 2. भारतीय र्यलर जवजनयं, 1950 (जिसंें इसके पश्चात इसे ंूल जवजनयं कहा गया ह)ै के जवजनयं 4, खंड (ग), उप-खंड (vi) ंें ‘रिप् पण’ कयोग जनम्न जलजखत ‘रिप् पण’ रखा िाएगा, अथाधत-् “रिप् पण: िर तक दक राष्‍टर ीय धात ु जवन पान प्रययोगगिाला या भारत हवे ी इलेज रकल जलजंिेड, हिै राराि की जनगं अनुसंधान रर जवकास प्रययोगगिाला या केंरीय र्यलर रयोगड ध द्वारा ंान्‍द यता प्राप् त दकसी अन्‍द य जव्‍ यात धात ु िांच प्रययोगगिाला द्वारा िेि ं ें उत् पादित जंर ध धातु इस्ट्प ात के रे े हुए तापंान के आंकों ों के सरहणं हण हते ु क्रीप िेटिस्ट्िंग हते ु या राष्‍टर ीय रूप से ंान्‍द यता प्राप् त िांच प्रययोगगिाला से ििे से राहर उत् पादित जंर ध धात ु इस्ट् पात के जलए जवजनंाधण के ििे ंें क्रीप िेटिस्ट्िंग हते ु अंेररकन सयोगसाइिी ऑफ ंैकेजनकल इंिीजनयसध (एएसएंई) या जिरिि स्ट् ितडडध (रीएस) या यूरयोगपीय स्ट् ितडड ध (ईएन) कयोगड के अनुसार 33,000 घंिे तक िांच करन े पर इस्ट् पात के इन रहणडे ों कयोग स्ट् वीकार दकया िा सकेगा रर िीघावध जध रे े हुए तापंान की जविेाता/ अ अजधकतं अनन पु ेय िार गुण ियोग अंेररकन सयोगसाइिी ऑफ ंैकेजनकल इंिीजनयसध (एएसएंई) या जिरिि स्ट् ितडडध (रीएस) या यूरयोगपीयन स्ट् ितडडध (ईएन) कयोगड ंें दिए गए ह,त िैसा भी ंांला हयोग, का उपययोगग जडिाइन के जलए दकया िाएगा, ियोग यथा लागू जनम् नजलजखत िततों कयोग पूरा दकए िाने के अ्‍ यधीन ह,ै अथाधत ्- (क) इस्ट् पात के उत् पािक द्वारा इस प्रभाव का एक प्रंाण प् प्रस्ट् तुत कर दकया गया ह ै दक इस्ट्प ात का जवजनंाधण स्‍ ती से अंेररकन सयोगसाइिी ऑफ ंैकेजनकल इंिीजनयसध (एएसएंई) या जिरिि स्ट् ितडड ध (रीएस) या यूरयोगपीयन स्ट् ितडडध (ईएन) कयोगड की अपेिा/ के अनुसार दकया गया ह ै तादक क्रीप रप् चर अपेिा/ का अनुपालन दकया िाना सुजनजश्चत दकया िा सके; (ख) इस्ट् पात जनंाधता अपेजित प्रंाण प् प्रस्ट् ततु करता ह ै दक इस्ट् पात रासायजनक जव‍ लेाण रर कि रर रे े हुए तापंान की यांज्क जविेाता/ िैसा दक अंेररकन सयोगसाइिी ऑफ ंैकेजनकल इंिीजनयस ध (एएसएंई) या जिरिि स्ट् ितडड ध (रीएस) या यूरयोगपीयन स्ट् ितडड ध (ईएन) कयोगड ं ें िी गई ह,ै िैसा भी ंांला हयोग, के अनुरूप ह;ै (ग) 1000 घंिों की लघु अवजध िार-रप् चर िांच, िैसा दक नीचे जववरण दिया गया ह,ै राष्‍टर ीय धात ु जवन पान प्रययोगगिालाअप्र्‍ यात इस्ट् पात जनंाधता या केंरीय र्यलर रयोगड ध द्वारा ंान्‍द यता प्राप् त दकसी अन्‍दय धात ु िांच प्रययोगगिाला द्वारा इस्ट् पात संयं्ों द्वारा िेि ंें उत् पादित जंर ध धातु इस्ट् पात के रे े हुए तापंान के आंकों ों के संरहणहण हते ु क्रीप िेटिस्ट्िंग हते ु या राष्‍टर ीय स्ट् तर पर ंान्‍द यता प्राप् त अथवा प्रत् याजसत िांच प्रययोगगिाला स े िेि के राहर उत् पादित जंर ध धात ु इस्ट् पात के जलए जवजनंाधण के ििे ं ें क्रीप िेटिस्ट्िंग हते ु इस प्रययोगिन के जलए दकया िाता ह ै दक य ा इस्ट् पात िीधाधवजध रप् चर िार गणु या अजधकतं अनन पु ेय िार गुण ियोग अंेररकन सयोगसाइिी ऑफ ंैकेजनकल इंिीजनयसध (एएसएंई) या जिरिि स्ट् ितडड ध (रीएस) या यरू योगपीयन स्ट्ि तडड ध (ईएन) कयोगड ंें दिए गए ह,त िैसा भी ंांला हयोग रर राष्‍टर ीय धात ु जवन पान प्रययोगगिाला या इस्ट्प ात संयं् द्वारा इस संरंध ंें दिया गया एक प्रंाण प्;[भाग II—खण् ड 3(i)] भारत का रािप् : असाधारण 3 (घ) ट्यूटिरंग या पाइटिपगं या काटिस्ट्िंग या प् लेि रहणडे के जलए इस्ट् पात के प्रत् येक रहणेड के जलए 1000 घंिे के ियोग क्रीप रप् चर िांच स्वधस तापंान 50 जडरहणी से अजधक के तापंान पर दकए िाएंगे; िर वे भट्टी या सुपर-हीिर ियोगन ंें हों: (ड.) वाल् व ंें प्रयु त फ््िगग 1000 घंिे के जलए 550 जडरहणी सेंिीरहणडे पर िांच की िानी चाजहए तथा ित ध (ग) ंें जवजनर्िष्‍टध ि उपयुध त तापंान पर 1000 घंिे ंें रप् चर करने का िराव-20 प्रजतित लाइन के राि ंास्ट् िर कवध पर जलया िा सकता ह;ै (च) 1000 घंिे के न्‍द यनू तं रप् चर िीवन का अनुंान ह ै तथा ियोगनों नंूनों कयोग उपयुध त िराव रर तापंान पर 1000 घंिे कयोग िांच पर पास करना चाजहए; (छ) भारत ं,ें इन नंूनों कयोग संरंजधत राज्य के ंु्‍य र्यलर जनरीिक रर भारत के राहर जनरीिण प्राजधकारी द्वारा क्रंरजहत तरीके से चुना िा सकता है, तथा नंून े अध-ध जन्ंधत अवस्ट् था ं ें हयोग सकत े ह त िैसे, लगभग 25 वग धजंंी. के फयोगज्डध रार जिन्‍द ह ेंसंगत ्‍ यौरे के अनुसार हीि रीिंेंि से गुिरना हयोगगा।” 3. ंूल जवजनयंों ं,ें जवजनयं 4क ंें, उप-जवजनयं (1) कयोग जनम्न जलजखत उप-जवजनयं रखा िाएगा, अथाधत ् - “(1) गजतजवजध के एक ऐस े ि्े जिसंें वे सलं ग्न ह,त ं ें सिं प्राजधकरण, जनरीिण प्राजधकरण, जव्‍ यात सांरहणी िांच प्रययोगगिाला, जव्‍ यात इस्ट्प ात जनंाधता, जव्‍ यात फाउन्‍द रीअफयोगि,ध जव्‍ यात ट्यूरअपाइप जनंाधता रर जव्‍ यात रेंनेंि लाइफ असेसंेंि ऑगधनाइिेिन के रूप ंें ंान्‍द यता प्राप् त करन े के जलए आवेिन सजचव, केंरीय र्यलसध रयोगड,ध उ्योगग संवधधन रर आंतररक व्य ापार जवभाग, वाजणज् य रर उ्योगग ंं्ालय कयोग भेिा िाएगा जिसंें वह फंध ंें लगी ह।ै ” 4. ंूल जवजनयंों ं,ें जवजनयं 4ख ंें, उप-जवजनयं (4) कयोग जनम्न जलजखत उप-जवजनयं रखा िाएगा, अथाधत ्- “(4) ंूल् यांकन सजंजत या आकलन सजंजत, िैसा भी ंांला हयोग, इस रारे ंें संाधान हयोगने के राि दक उप- जवजनयं (1) रर (2) ंें जवजनर्िष्‍टध ि अपिे ाएं परू ी की गई हत, ंान्‍द यता िने े अथवा न िेन े की जसफाररि के जलए सिस्ट् य सजचव, केंरीय र्यलर रयोगडध कयोग ररपयोगिध प्रस्ट् तुत करेगी।” 5. ंूल जवजनयं ं,ें जवजनयं 4ग कयोग जनम्न जलजखत जवजनयं रखा िाएगा, अथाधत ्- “4 ग. सिं प्राजधकरण, जनरीिण प्राजधकरणों के रूप ं ेंफं धकयोग ंान्‍दय ता िने ा - ंूल् यांकन सजंजत या आकलन सजंजत, िैसा भी ंांला हयोग, की ररपयोगिध की िांच करके सिस्ट्य सजचव, केंरीय र्यलस ध रयोगडध दकसी फंध कयोग दक्रयाकलाप के िे् ंें लागू प्रप्ों (प्रप् XVI-क स े XVI-झ) ंें से एक ंें ंान्‍द यता िेन े का जनणधय कर सकती ह:ै परंत ु अगर वह दक ंान्‍द यता कयोग अस्ट् वीकार करन े का जनणधय करती ह ै तयोग उसे आवेिक कयोग कारण सजहत इसका जलजखत उत् तर िेना हयोगगा।” 6. ंूल जवजनयं ं,ें जवजनयं 4च कयोग लयोगप दकया िाएगा। 7. ंूल जवजनयं ं,ें जवजनयं 4छ ं,ें उप-जवजनयं (1) कयोग जनम्न जलजखत उप-जवजनयं रखा िाएगा, अथाधत ्-4 THE GAZETTE OF INDIA : EXTRAORDINARY [PART II—SEC. 3(i)] “(1) ंूल् यांकन सजंजत या आकलन सजंजत के ंान्‍द यता प्रिान न करने के जनणधय से असंतुष्‍टि फंध ंान्‍दयता प्रिान करने से ंना करने के जखलाफ अ्‍ यि, केंरीय र्यलसध रयोगडध के संि जलजखत अपील फाइल कर सकती ह।ै ” 8. ंूल जवजनंयों ं,ें जवजनयं 4ि ं,ें उप-जवजनयं (7) क ं,ें खंड (ii) कयोग जनम्न जलजख खंड रखा िाएगा, अथाधत ्- “(ii) कायधरत र्यलस ध के जलए संरंजधत र्यलर जनरीिणालय से जनरीिण प्राजधकारी के िररए अथवा स्ट् वतं् कायधकरण की जस्ट्थजत ं ें सीधे ही जनरीिण पुजस्ट्तका न पापन की प्रजत प्राप् त की िाएगी ियोग अंजतं जनरीिण की तारीख से एक सप् ताह के भीतर लौिाई िाएगी तादक उसंें आव‍ यक प्रजवजटिययां की िा सकें।” 9. ंूल जवजनयं ं,ें जवजनयं 5 ं,ें उप-जवजनयं (ii) ंें ि्‍ि ‘ंु्‍य जनरीिक’ ि्‍ ि िहां भी आए ह,त उन्‍द ह ें ‘जनरीिण प्राजधकारी’ ि्‍ ि रखे िाएंगे।” 10. ंूल जवजनयंों ं,ें जवजनयं 290 ं,ें खंड (क) ंें “सभी चेस्ट् ि रर दफिंिं्‍ स ..... से िरूु हयोगन े वाले रर “…….जिसके जलए उन्‍द ह ें रनाया गया ह”ै से संाि हयोगने वाल ेि्‍िों कयोग जनम्न जलजखत ि्‍ि रखे िाएंग,े अथाधत् - “सभी चेस्ट् ि रर दफिंिं्‍ स सही, ंिरूत रर दकसी भी खांी, िरार या अन्‍द य खरारी के जरना होंगी तथा इनके पूरा हयोगने के राि चस्ट्े ि कयोग उस संचालनरत वाल् व के जलए अनुंेय अजधकतं कायधिील िराव के डेे गनु ा िराव पर हाइर्जलक रूप से िांचा िाएगा जिसके जलए उन्‍द हें रनाया गया ह।ै ” 11. ंूल जवजनयं ं ेंजवजनयं 361 के स्ट्थान पर जनम्नजलजखत जवजनयं रखा िाएगा, अथाधत् - “361. र्ि रड्ें स - पाइप रेंड पर दकसी भी संय व्ल की न्‍दय ूनतं ंयोगिाई जनम्न जलजखत ं ें से दकसी एक तरीके से नांत: (क) रर (ख) से जनधाधररत की िाएगी, अथाधत् - (क) (क) तैयार रेंड ंें दकसी भी संय व्ल की न्‍द यूनतं ंयोगिाई जवजनयं 350 ंें दिए गए सू् 91 अथवा 91क ंें अपेजित ंयोगिाई से कं नहीं हयोगगी। (ख) जवजनंाधण प्रदक्रया के आधार पर रेंड जथटिनंग अलाउंस कयोग चुना िाएगा तादक रेंटिडंग के राि न्‍द यूनतं ंयोगिाई की आव‍ यकता कयोग सुजनजश्चत दकया िा सके। (ग) इस प्रकार चुने गए रडें जथटिनंग अलाउंस कयोग अंजतं उत्प ाि पर कयोगई भी हाजनकारक प्रभाव डाले जरना पाइप की पररजध के क्र्स से ि न के सभी जहस्ट्स ों ं ेंउपल्‍ ध कराया िाना ह।ै (ख) रेंटिडंग के राि इसके तैयार रूप ंें रडें की अपेजित न्‍द यूनतं ंयोगिाई t संीकरण (i) या (ii) के अनुसार m जनधाधररत की िाएगी, अथाधत ् - t = P x D +C [संीकरण (i)] िर गणना का आधार राहरी m व्य ास ह।ै ‘D’ 2 x (f x e / I)+P िर गणना का आधार आतं ररक t = P x d +C [संीकरण (ii)] m व्य ास ह।ै ‘d’ 2 x (f x e/I)-P[भाग II—खण् ड 3(i)] भारत का रािप् : असाधारण 5 िहां, t =रेंड के व्ल की न्‍द यनू तं ंयोगिाई जं.ंी. ं,ें m P = अजधकतं कायधिील िराव दकरहणा./वगध सेंंी., D = पाइप का राहरी व् यास जंंी. ं,ें d = पाइप का आंतररक व् यास जंंी. ं,ें f = जवजनयं 271 के तहत अनुंये िराव दक.रहणा.अवग धसेंंी., e = ििता कारक, = सींलेस रर अ्‍ याय II की अपेिा/ कयोग परू ा करते हुए इलेज रक रेजिस्ट् िेंस वेजल्डड स्ट् िील पाइप् स रर इलेज रक ्यूिन वेजल्डड स्ट् िील पाइप् स के जलए 1.0 जिसंें वेल् ड पूरी तरह स े रेजडययोगरहणा्ड ह ैअथवा अल् रास्जनक रूप से िांचा गया ह,ै = अ्‍ याय II की अपेिा/ कयोग पूरा करत े हुए इलेज रक ्यूिन वजे ल्डड स्ट् िील पाइप् स के जलए 0.95, = 22 जंंी. तक के t के गुण (पाइप की न्‍द यूनतं ंयोगिाई) के जलए वेजल्डड स्ट् िील पाइप के जलए 0.90 , = 22 जंंी. से अजधक रर 29 जंंी. तक के t के गुण (पाइप की न्‍द यूनतं ंयोगिाई) के जलए वेजल्डड स्ट् िील पाइप के जलए 0.85, = 29 जंंी. के ऊपर t के गुण (पाइप की न्‍द यनू तं ंयोगिाई) के जलए वेजल्डड स्ट् िील पाइप के जलए 0.80, C = 0.75 जंंी. I = [4x (R/D)-1] { इनरेडयोगस ं ें(रेंड के अंिर)}, [4x (R/D)-2] = [4x (R/D)+1] { ए सरेडयोगस ंें (रेंड के राहर)}, [4x (R/D)+2] = 1.0 { रेंड सेंिर लाइन की साइड व्ल पर}, िहां, R = पाइप रेंड का रेंड अध-ध व् यास जंंी. ं ें(नीचे जच् िेख)ें , D = पाइप का राहरी व् यास (क) इंरेडयोगस स ेए सरेडयोगस रर रेंड के अंत तक ंयोगिाई ंें धीरे-धीरे रिलाव हयोगगा। (ख) ऊपर गणना न्‍द यनू तं ंयोगिाई आव‍ यकता तैयार रेंड की ए स रेडयोगस, इंरेडयोगस रर रडें सेंिर लाइन ं ें परू ी हयोगनी चाजहए (नीचे जच् िेख)ें ।6 THE GAZETTE OF INDIA : EXTRAORDINARY [PART II—SEC. 3(i)] (ग) रेंड्स के अतं ंें न्‍द यूनतं ंयोगिाई जवजनयं 350 ंें दिए गए संीकरण 91 अथवा 91क की अपेिा/ से कं नहीं हयोगगी। (घ) जवजनंाधण प्रदक्रया के आधार पर रेंड जथटिनगं अलाउंस कयोग चुना िाएगा तादक रेंटिडंग के राि न्‍द यूनतं ंयोगिाई की आव‍ यकता कयोग सुजनजश्चत दकया िा सके। .”. 12. ंूल जवजनयं ं,ें जवजनयं 381 ंें उप-जवजनयं (1) ं,ें खंड (ख) कयोग, जनम्न जलजखत खंड रखे िाएंग,े अथाधत् - “(ख) ंु्‍य जनरीिक द्वारा प्रय ु त दकए िाने वाली दकसी भी जववेकाधीन अजधकार के अधीन, वह प्रप्- II रर प्रप्-III ंें जनरीिण प्राजधकारी द्वारा यथा प्रंाजणत र्यलर के अनुंत वर्कगग प्रिे र कयोग स्ट् वीकार करेगा रर र्यलर का जनरीिण करन े के राि, जवजनयं 379 की अपेिा/ के अनुसार इसका हाइर्जलक रूप स े िांच करेगा रर हाइर्जलक िांच के राि प्रप्-V ंें धारा 9 के तहत एक अंजतं आििे िारी दकया िाएगा। (खक) यदि खडं (ख) के अंतगतध जवजनर्िटियध अनंजतं आिेि की अपेिाएं परू ी नहीं हयोगती, तयोग इसके प‍ चात ् जरना दकसी जनरीिण रर फीस के भुगतान के, अगल े छ: ंहीने की अवजध के जलए नए अनंजतं आिेि िारी दकए िाएंगे ियोग पहले अनंजतं आिेि िारी हयोगन े की तारीख स ेअजधकतं 12 ंाह की कुल अवजध से अजधक नहीं हयोगना चाजहए।” 13. ंूल जवजनयंों ं,ें जवजनयं 382 के खडं (क) की राज्य ों रर संघ राज्य िे्ों की सूची ंें - (क) जहंाचल प्रििे रर उससे संरंजधत प्रजवजटिय के राि, जनम्न जलजखत प्रजवजटिय अंत:स्ट्थाजपत दकया िाएगा, अथाधत ्- “िम् ं ू रर क‍ ंीर िेके।”; (2) ल क ािीव, जंजनकयोगय रर अजंजनदिजव द्वीपसंूह रर उससे संरंजधत प्रजवजटिय के पश्चात जनम्न जलजखत अतं :स्ट्थाजपत दकया िाएगा, अथाधत ्- “लििृ ाख एलए।”[भाग II—खण् ड 3(i)] भारत का रािप् : असाधारण 7 14.ंूल जवजनयंों ं,ें जवजनयं 391-क के, खंड (क) ं,ें उपखंड (ii) के पश्चात, जनम्न जलजखत उप-खंड कयोग अतं :स्ट्थाजपत दकया िाएगा, अथाधत ्- “(iii) िले िाइप वस्ट्े ि हीि र्यलस ध(अनफायड)ध : - (क) िेल िाइप वेस्ट् ि हीि र्यलसध (अनफायडध) के प्‍ चीस वा ध के िीवनकाल के परू ा हयोगन े पर, केंरीय र्यलर रयोगड ध द्वारा अनुंयोगदित रेंने ेंि लाइफ एससे ंेंि ऑगनध ाइिेिन (आरएलएओ) द्वारा उसका न्न-जडस्ट् रज िवली रूप से िांच की िाएगी। (ख) इस तरह के र्यलसध के प्रिे र पार्टसध िैसे िेल, एंडप्ल ेि, स्ट्ि तड पाइप का जनरीिण अल् रासयोगजनक िांच, चुंरकीय कण िांच रर डाई पेनेरेंि िांच द्वारा दकया िाएगा। (ग) यदि इसके पररणां केंरीय र्यलसध रयोगडध द्वारा जनधाधररत ंानकों के अनुसार स्ट् वीकायध ह,त तयोग र्यलरों के िीवन- काल कयोग आगे रारह वाध की अवजध के जलए या रेंेनेंि लाइफ एसेसंेंि ऑगधनाइिेिन द्वारा यथा-संस्ट् तुत दकसी कं अवजध के जलए रे ान े हते ,ु ंु्‍य जनरीिकअ जनिेिक र्यलसध द्वारा एक प्रंाण प् िारी दकया िाएगा। (घ) रेंेनेंि लाइफ एसेसंेंि ऑगनध ाइिेिन की अनुिंसा पर इस तरह के र्यलर के वर्कगग प्रेिर कयोग कं दकया िा सकेगा। (ङ) न्न-जडस्ट् रज िव िांच द्वारा िेा िीवन-काल का यह ंल्ू यांकन उसके राि हर रारह वा ध राि केंरीय र्यलसध रयोगड ध द्वारा अनुंयोगदित रेंनेंि लाइफ एसेसंेंि ऑगनध ाइिेिन (आरएलएओ) द्वारा दकया िाएगा रर ऐिेंसी ं्‍ु य जनरीिकअ जनिेिक, िैसा भी ंांला हयोग, र्यलर कायाधलय के साथ संन्‍दव य करते हुए कायध करेंगी। रिप् पण: (1) इसंें स्ट् वांी के पास ऊपर परै ा (i) या पैरा (ii) के उपरंधों का चयन करन े का जवकल् प हयोगगा या परै ा (iii) के अनुसार र्यलर के िेा िीवन-काल आकलन का जवकल् प चुनना हयोगगा। (2) िहां भी, िेा िीवन-काल ंल्ू य ांकन के जलए र्यलर के न्न-जडस्ट् रज िव िांच करना संभव नहीं ह,ै वहा ं पैरा (i) या पैरा (ii) के उपारंध लाग ूहोंगे।”; 15. ंूल जवजनयंों ं,ें जवजनयं 393 के, खंड (घ) ं,ें जवजनयं 385क ंें जनधाधररत ि्‍ िों, अिरों रर अंकों के राि, जनम्न जलजखत ि्‍ िों, अिरों रर अंकों कयोग अंत:स्ट्थाजपत दकया िाएगा, अथाधत ्- “ अजधकतं 50,000 रुपए के अधीन” . 16. ंूल जवजनयंों ं,ें जवजनयं 395 के खडं (ख) ं,ें ─ (i) उप-खंड (i) ंें “5,000 रुपए ” अिरों रर अंकों कयोग जनम्न जलजखत अिर रर अंक अंत:स्ट्थाजपत दकया िाएगा, अथाधत ्- “500 रुपए” ; (ii) उप-खंड (ii) ं ें “1,000 रुपए ” अिरों रर अंकों के स्ट्थान पर, जनम्न जलजखत अिर रर अंक रखा िाएगा, अथाधत-् “500 रुपए”8 THE GAZETTE OF INDIA : EXTRAORDINARY [PART II—SEC. 3(i)] 17. ंूल जवजनयंों ं,ें जवजनयं 395ग के स्ट्थान पर, जनम्न जलजखत जवजनयं रखा िाएगा, अथाधत् - “395ग. व्ल्व रर ्ल्‍त स के जलए जनरीिण फीस (1) 600 रुपए प्रजत जनरीिण के न्‍द यूनतं जनरीिण फीस के अधीन वाल् व ” के जनरीिण के जलए फीस जनम्न ानुसार जलया िाएगा: (क) 25 जंंी. तक 15 रुपए प्रजत ंा्ानुपाती (ख) 25 जंंी. से ऊपर रर 100 जंंी. तक 45 रुपए प्रजत ंा्ानुपाती (ग) 100 जंंी से ऊपर रर 250 जंंी. तक 270 रुपए प्रजत ंा्ानुपाती (घ) 250 जंंी. से ऊपर 720 रुपए प्रजत ंा्ानुपाती (2)्लन्‍दै िेस के जनरीिण के जलए प्रभारण जनम्न ानुसार जलया िाएगा: (i) फ्ज्ड ध रर कास्ट् ि ्लैन्‍द िेस के जलए: (क) 50 या उसके जहस्ट्स े के एक रैच के जलए 25 जंंी तक रर 25 225 रुपए जंंी सजहत (ख) 100 या उसके जहस्ट्स े के एक रैच के जलए 25 जंंी तक रर 390 रुपए 25 जंंी सजहत (ग) 50 या उसके जहस्ट्स े के एक रैच के जलए 25 जंंी से अजधक 435 रुपए रर 50 जंंी सजहत (घ) 25 या उसके जहस्ट्स े के एक रैच के जलए 50 जंंी से अजधक 435 रुपए रर 100 जंंी सजहत (ड.) 10 या उसके जहस्ट्स े के एक रैच के जलए 100 जंंी स े 465 रुपए अजधक रर 250 जंंी सजहत (च) 5 या उसके जहस्ट्स े के एक रैच के जलए 250 जंंी से अजधक 540 रुपए (ii) ्लैि ्लैन्‍द िेस के जलए: फ्ज्ड ध रर कास्ट् ि ्लैन्‍द िेस के जलए ली िाने वाली िर से आधा प्रभाररत जलया िाएगा।” 18. ंूल जवजनयं ं,ें जवजनयं 395-छ के स्ट्थान पर जनम्न जलजखत जवजनयं रखा िाएगा, अथाधत् - “395छ. पुितों रर र्यलर घिकों के जलए जनरीिण फीस– (1) सभी प्रकार के क्इल, अथाधत,् इकयोगनयोगंाइिर क्इल् स, सुपरहीिर क्इल् स, ररहीिर क्इल् स के जलए जनरीिण फीस, सतह िे् के आधार पर जलया िाएगा, िैसा दक जवजनयं, 385-क ंें उपारंध दकया गया ह।ै (2) ट्यरू रर ट्यूर-रेंड के जनरीिण के जलए 10 रुपए प्रजत ंीिर की िर से जलया िाएगा, ियोग दक न्‍द यनू तं 500 रुपए हयोगगा।” 19. ंूल जवजनयंों ंें, जवजनयं 525 के, खंड (ड.) के पश्चात, जनम्न जलजखत खंड कयोग अतं ंें अंत:स्ट्थाजपत दकया िाएगा, अथाधत ्- “(च) यदि खंड (ङ) के अंतगधत जवजनर्िटियध अनंजतं आििे की अपेिाएं परू ी नहीं हयोगती ह,त तयोग इसके प‍ चात ् जरना दकसी जनरीिण रर फीस के भुगतान के नए अनंजतं आििे िारी दकए िाएंग े ियोग पहल े अनंजतं आिेि िारी हयोगन े की तारीख स े24 ंाह की एक अजधकतं अवजध से अजधक नहीं हयोगना चाजहए।”.[भाग II—खण् ड 3(i)] भारत का रािप् : असाधारण 9 20. ंूल जवजनयंों के, प्रारूप-1 ं,ें “से्िी व्ल्व के अपेजित िे्” िीाध के अधीन, “सुपरहीिेड स्ट् िीं के जलए” उप- िीाध के तहत, जव्ंान प्रजवजटिय के स्ट्थान पर जनम्नजलजखत प्रजवजटिय रखी िाएगी, अर अथाधत:् - “ .”. 21. ंूल जवजनयंों ं,ें पररजिष्‍टि -ञख के स्ट्थान पर जनम्न जलजखत रखा िाएगा, अथाधत-् “पररजिष्‍टि ञख [जवजनयं 376 (चचच) िेख]ें क. केवल जनरंतर प्रदक्रया संयं् ंें प्रयु त रीस वाध तक के िीवन-काल वाले वेस्ट् ि हीि र्यलस ध (फायडध)। (1) केवल जनरंतर प्रदक्रया संयं् ंें प्रयु त 20 वा ध तक के िीवन-काल वाल े वेस्ट् ि हीि र्यलसध (फायडध) के जलए, 12 ंहीने संाप् त हयोगने पर तथा जवजनयं 390 ंें िी गई प्रदक्रया के अनुसार दकए गए जनरीिण की तारीख से चौरीस ंहीने पूरे हयोगने पर रर राज्य के संरंजधत सिं व् यजि द्वारा िारी ययोग्‍ यता प्रंाण-प् जंलने तथा सम्यक रूप से भरे गए प्रारूप XIX ंें आवेिन सजहत नीचे दिए गए अनुसार प्रचालन ररक्ड ध से संाधान हयोगने पर रर रारह ंहीनों के जलए संचालन की अनुन पा िी िाएगी:- (क) आंकों ा अजधरहणहण प्रणाली (डीएएस) के आउिपुि स े सुपरहीिर रर रीहीिर ितपरेचर ए स किधन्‍द स के जलए प्रचालन आंकों े या ल्ग िीि तापंान ररक्ड ध ंें रखे गए सपु रहीिर ितपरेचर ए सकिधन के जलए प्रचालन आंकों े; (ख) कारणों रर की गई कारधवाई सजहत जपछले वा ध के िौरान हुए ििडाउन का ्‍ यौरा; (ग) वाध के िौरान र्यलर प्रेिर पार्टसध पर दकए गए न्न-जडस्ट् रज िव िांच के ररक्ड;ध (घ) र्यलर ं ें पानी की गुणवत् ता ऐसे र्यलसध की आव‍ यकता/ के अनुसार ह ै तथा गुणवत्त ा के ऑन लाइन आंकों े, आंकों ा अजधरहणहण प्रणाली (डीएएस) के िररए या संय्ं अथवा पानी के स्रयोगत के पास रखी गई ररक्ड ध ल्गरुक के िररए उपल्‍ध कराए िाते ह;त (ड.) र्यलर ट्यूर फेजलयर ररक्डध (स्ट् थान, ठीकअ प्रजतस्ट्थ ाजपत दकए गए ट्यू्‍ स की सं्‍ या. (2) जवजनंय 390 उपरंध के अनुसार छत्त ीस ंहीने की अवजध संाप् त हयोगने के राि संरंजधत सिं व् यज त द्वारा जनरीिण दकया िाएगा। (3) यदि प्रंाणन अवजध की संाजप् त से पहल े या प्रंाणन के छ: ंहीन े राि दकसी भी संय पंरह दिन या उससे ज्य ािा संय के जलए ििडाउन रहता ह ै तयोग सिं व् यज त कयोग सम्यक रूप से सूजचत दकया िाएगा तादक उ त ििडाउन अवजध के िौरान जनरीिण दकया िा सके। ख. 20 वाध तक के वेस्ट् ि हीि र्यलसध (अनफायड)ध केवल जनरंतर प्रदक्रया संयं् ं ेप्रयु त (1) केवल जनरंतर प्रदक्रया संयं् ंें प्रयु त 20 वाध तक के वेस्ट्ि हीि र्यलसध (अनफायडध) कयोग, जवजनयं 390 ंें िी गई प्रदक्रया के अनुसार राज्य ं ें संरंजधत सिं व् यजि द्वारा दकए गए जनरीिण रर ययोग्‍ यता प्रंाण-प् के चौरीस ंहीन े राि तथा परै ा ‘क’ ंें संचालन ररक्डध से संाधान हयोगने पर उस ेचौरीस ंहीनों की एक रर अवजध के जलए संचालन की अनुन पा िी िाएगी। (2) जवजनयं 390 ं ें िी गई व् यवस्ट् था के अनुसार अों ताजलस ंहीने की अवजध संाप् त हयोगने के राि संरंजधत सिं व् यजि द्वारा जनरीिण दकया िाएगा। (3) यदि प्रंाणन अवजध की संाजि से पहले या प्रंाणन के छ: ंहीने रात दकसी भी संय पंरह दिन या उससे ज्य ािा संय के जलए ििडाउन रहता ह ै तयोग सिं व् यजि कयोग सम्यक रूप स े सूजचत दकया िाएगा तादक उ त ििडाउन अवजध के िौरान जनरीिण दकया िा सके।10 THE GAZETTE OF INDIA : EXTRAORDINARY [PART II—SEC. 3(i)] ग. 20 वाध से अजधक परु ाने वेस्ट्ि हीि र्यलसध (फायडध) केवल जनरंतर प्रदक्रया संयं् ंें प्रयु त। (1) जवजनयं 390 ं ें िी गई व्य वस्ट् था के अनुसार रीस वा ध से अजधक परु ान े र्यलर प्रजतवा ध जनरीिण के अ्‍ यधीन होंग े ियोग राज्य ंें संरंजधत सिं व् यजि संाधान के अनुसार हयोग। (2) यदि र्यलर का रेंनेंि लाइफ असेसंेंि इन जवजनयंों के उपारंधों के अनुसार दकया िाता ह ै रर यदि यह संाधानप्रि पाया िाता ह ै तयोग पैरा ‘क’ ंें िी गई प्रदक्रया लाग ू हयोगगी। घ. रीस वाध से अजधक परु ाने वस्ट्े ि हीि र्यलसध (अनफायडध) केवल जनरंतर प्रदक्रया संयं् ंें प्रयु त। (1) जवजनयं 390 उपरंध के अनुसार रीस वाध स े अजधक परु ाने र्यलर प्रजतवाध जनरीिण के अ्‍ यधीन होंग े ियोग राज्य ंें संरंजधत सिं व् यजि संाधान के अनुसार हयोग। (2) यदि र्यलर का रेंनेंि लाइफ असेसंेंि इन जवजनयंों के उपारंधों के अनुसार दकया िाता ह ैरर यदि यह संाधानप्रि पाया िाता ह ैतयोग पैरा ‘ख’ ंें िी गई प्रदक्रया लाग ूहयोगगी।” [फा.सं.पी-30011अ1अ2020-र्यलस]ध िी.एस.िी. नारायणन, सजचव, केंरीय र्यलसध रयोगड ध रिप्पण:- ंूल जवजनयं का.आ.600 दिनांक 15 जसतंरर, 1950 के द्वारा भारत के रािप् ं ेंप्रकाजित हुए थे रर इनंें संियोगधन सा.का.जन. 123(अ) तारीख 17 फरवरी, 2020 के द्वारा अंजतं दकया गया था। MINISTRY OF COMMERCE AND INDUSTRY (Department for Promotion of Industry and Internal Trade) (CENTRAL BOILERS BOARD) NOTIFICATION New Delhi, the 11th September, 2020 G.S.R. 551(E).—Whereas certain draft regulations further to amend the Indian Boiler Regulations, 1950 were published as required under sub-section (1) of section 31 of the Boilers Act, 1923 (5 of 1923) vide notification of the Government of India, Ministry of Commerce and Industry(Department for Promotion of Industry and Internal Trade), (Central Boilers Board) number G.S.R. 343 (E), dated the 21st May, 2020 in the Gazette of India, Extraordinary, Part II, Section 3, Sub-Section (i) inviting objections and suggestions from all persons likely to be affected thereby, before the expiry of the period of forty-five days from the date on which the copies of the said Gazette notification were made available to the public; And whereas, the copies of the said notification were made available to the public on the 6th June, 2020; And whereas, no objections and suggestions were received from the public on the said draft regulations; Now, therefore, in exercise of the powers conferred by section 28 of the Boilers Act, 1923 (5 of 1923), the Central Boilers Board hereby makes the following regulations further to amend the Indian Boiler Regulations, 1950, namely:- 1. Short title and commencement.-- (1) These regulations may be called the Indian Boiler (Second Amendment) Regulations, 2020. (2) They shall come into force on the date of their publication in the Official Gazette. 2. In the Indian Boiler Regulations, 1950 (hereinafter referred to as the principal regulations), in regulation 4, in clause (c), in sub- clause (vi), for the Note, the following Note shall be substituted, namely:- “Note: Until 33,000 hours tests are carried out by the National Metallurgical Laboratory or Corporate Research and Development Laboratory of Bharat Heavy Electricals Limited, Hyderabad or any other well- known material testing laboratory recognized by the Central Boilers Board for creep testing for collecting elevated temperature data of alloy steel produced indigenously or from a Nationally recognized/accredited testing laboratory for creep testing in the country of manufacture for alloy steel produced outside India, against American Society of Mechanical Engineers (ASME) or British Standards (BS) or European Standards (EN) Code, these grades of steel may be accepted and long time elevated temperature properties/maximum allowable stress values given in American Society[भाग II—खण् ड 3(i)] भारत का रािप् : असाधारण 11 of Mechanical Engineers (ASME) or British Standards (BS) or European Standards (EN) Code, as the case may be, used for the purpose of design subject to fulfillment of the following conditions as applicable, namely:- (a) a certificate is furnished by the producer of the steel to the effect that the steel has been manufactured strictly in accordance with the technical requirements of the American Society of Mechanical Engineers (ASME) or British Standards (BS) or European Standards (EN) Code to assure that the creep rupture requirements are complied with. (b) the steel maker furnishes the necessary certificate that the steel conforms to the chemical analysis, room and elevated temperature mechanical properties given in American Society of Mechanical Engineers (ASME) or British Standards (BS) or European Standards (EN) Code as the case may be. (c) the short-term stress-rupture tests for 1000 hours as described below are carried out by National Metallurgical Laboratory or well known steel makers or any other material testing laboratory recognised by the Central Boilers Board for creep testing for collecting elevated temperature data of alloy steel produced indigenously or from a Nationally recognised or accredited testing laboratory for creep testing in the country of manufacture for alloy steel produced out side India, for the purpose of checking whether the steel is up to the specification and also to ensure that the steel is capable of meeting the long-term rupture stress values or maximum allowable stress values given in American Society of Mechanical Engineers (ASME) or British Standards (BS) or European Standards (EN) Code, as the case may be, and a certificate is given by National Metallurgical Laboratory or steel plant to this effect. (d) two numbers of 1000 hour creep rupture tests shall be carried out at a temperature 50°C above the service temperature for each grade of steel for tubing or piping or castings or plates grades; when in furnace or in superheater zone. (e) forging to be used in valves shall be tested at 550°C for 1000 hours and the stress to cause rupture in 1000 hours at above temperatures may be taken from the master curve corresponding to - 20 per cent line. (f) a minimum rupture life of 1000 hours is expected at this stress and both the samples should pass 1000 hour tests at the stress and temperature specified in condition (e). (g) in India, samples may be selected at random by the Chief Inspector of Boilers of the respective State and outside India by an Inspecting Authority, and the samples could be in the form of semi- finished products, say, forged bars of about 25 mm2 which will undergo heat treatment as prescribed by the relevant specifications .”. 3. In the principal regulations, in regulation 4A, for sub-regulation (1), the following sub-regulation shall be substituted, namely:- “(1) An application for recognition as Competent Authority, Inspecting Authority, Well-known Material Testing Laboratory, Well-known Steel Maker, Well-known Foundry/Forge, Well-known Tube/Pipe Maker and Well-known Remnant Life Assessment Organisation, in one of the area of activity in which they are engaged, shall be made by a firm to the Secretary, Central Boilers Board, Department for Promotion of Industry and Internal Trade, Ministry of Commerce and Industry.”. 4. In the principal regulations, in regulation 4B, for sub-regulation (4), the following sub-regulation shall be substituted, namely:- “(4) The Evaluation Committee or the Appraisal Committee, as the case may be, after satisfying itself that the requirements specified in sub-regulations (1) and (2) are fulfilled, shall submit a report to Member-Secretary, Central Boiler Board recommending either to grant or refuse recognition .”. 5. In the principal regulations, for regulation 4C, the following regulation shall be substituted, namely:- “4C. Recognition of a Firm as Competent Authority, Inspecting Authorities.— On examining the report of the Evaluation Committee or the Appraisal Committee, as the case may be, the Member-Secretary, Central Boilers Board may issue a certificate of recognition to the applicant in one of the Forms (Forms XVI-A to XVI-I) applicable to the area of activity: Provided that if it is decided to refuse recognition, it shall inform the applicant in writing giving reasons therefor.”. 6. In the principal regulations, regulation 4F shall be omitted. 7. In the principal regulations, in regulation 4G, for sub-regulation (1), the following sub-regulation shall be substituted, namely:-12 THE GAZETTE OF INDIA : EXTRAORDINARY [PART II—SEC. 3(i)] “(1) Any firm not satisfied with the reasons given by the Evaluation Committee or the Appraisal Committee for refusing to accord recognition may file an appeal in writing to the Chairperson, Central Boilers Board, against the refusal to grant recognition .”. 8. In the principal regulations, in regulation 4J, in sub-regulation (7) A, for clause (ii), the following clause shall be substituted, namely:- “(ii) A copy of Memorandum of Inspection Book shall be obtained from the concerned boiler inspectorate though the Inspecting Authority or directly if working independently, for in-service boilers which shall be returned within a period of one week from the date of completion of final inspection for making necessary entries therein.”. 9. In the principal regulations, in regulation 5, in sub-regulation (ii), for the words “Chief Inspector”, wherever they occur, the words “Inspecting Authority ” shall be substituted. 10. In the principal regulations, in regulation 290, in clause (a), for the words beginning with “All chests and fittings---” and ending with “---which they are intended”, the following words shall be substituted, namely:- “All chests and fittings shall be smooth, sound and free from flaws, cracks or other injurious defects and after completion, the chests shall be hydraulically tested at minimum one and half times the maximum allowable working pressure of the valve for which they are intended.”. 11. In the principal regulations, for regulation 361, the following regulation shall be substituted, namely:- “361. Wrought Bends.─ The minimum wall thickness at any point on the pipe bend shall be determined according to either of the following methods, namely, :- (A) (a) The minimum wall thickness at any point in the finished bend shall not be less than required by equation 91 or 91A given in regulation 350. (b) The bend thinning allowance shall be selected based on the manufacturing process to ensure the minimum thickness requirements after bending. (c) The bend thinning allowance thus selected is to be provided on all parts of the cross section of the pipe circumference without any detrimental effects on the final product. (B) The minimum required thickness t of a bend, after bending, in its finished form, shall be determined in m accordance with equation (i) or (ii), namely:- When outer diameter ‘D’ is t = P x D +C [ equation (i)] m the basis for calculation 2 x (f x e / I)+P When Inner diameter ‘d’ is the basis for calculation t = P x d +C [ equation (ii)] m 2 x (f x e/I)-P where, t = minimum wall thickness of a bend in mm, m P = maximum working pressure in Kgs./cm², D =outside diameter of pipe in mm, d = inside diameter of pipe in mm, f = allowable stress as provided under Regulation 271 in kg/cm², e = efficiency factor, = 1.0 for seamless and for electric resistance welded steel pipes and for electric fusion welded steel pipes complying with the requirements of Chapter II in which the weld is fully radiographed or ultrasonically tested, = 0.95 for electric fusion welded steel pipes complying with the requirements of Chapter II, = 0.90 for welded steel pipes for values of t ( minimum thickness of pipe) upto and including 22 mm,[भाग II—खण् ड 3(i)] भारत का रािप् : असाधारण 13 = 0.85 for welded steel pipes for values of t ( minimum thickness of pipe) over 22 mm and upto and including 29 mm, = 0.80 for welded steel pipes for values of t( minimum thickness of pipe) over 29 mm, C = 0.75 mm. I = [4x (R/D)-1] { at the intrados (inside of bend)}, [4x (R/D)-2] = [4x (R/D)+1] { at the extrados (outside of bend)}, [4x (R/D)+2] = 1.0 { at the side wall of the bend centre line}, Where, R = Bend radius of pipe bend in mm (see figure below), D = outside diameter of pipe (a) Thickness variations from the intrados to the extrados and at the ends of the bend shall be gradual. (b) The minimum thickness requirements calculated above should be met at the extrados, intrados and bend centre line of the finished bend (see figure below). (c) The minimum thickness at the ends of the bends shall not be less than the requirements of equation 91 or 91A given in regulation 350. (d) The bend thinning allowance shall be selected based on the manufacturing process to ensure the minimum thickness requirements after bending. . .”. 12. In the principal regulations, in regulation 381, in sub-regulation (1), for clause (b), the following clauses shall be substituted, namely:- “(b) Subject to any discretionary power exercised by the Chief Inspector, he shall accept the permissible working pressure of the boiler as certified by the Inspecting Authority in Form-II and Form-III and after inspecting the boiler, the Inspector shall hydraulically test it in accordance with requirements of regulations 379 and a provisional order under section 9 in Form V shall be issued after the hydraulic test. (ba) If the requirements of provisional order specified under clause (b) are not fulfilled, fresh provisional order shall be issued for a maximum of another six months subject to total period of twelve months from the date of issue of first provisional order, without any subsequent inspection and payment of fee.”. 13. In the principal regulations, in regulation 382, in clause (a), in the list of States and Union territories.─ (a) after Himachal Pradesh and entries relating thereto, the following shall be inserted, namely:- “Jammu and Kashmir JK .”;14 THE GAZETTE OF INDIA : EXTRAORDINARY [PART II—SEC. 3(i)] (b) after Laccadive, Minicoy & Aminidivi Islands and entries relating thereto, the following shall be inserted, namely:- “Ladakh LA.” . 14. In the principal regulations, in regulation 391A, in clause (a), after sub-clause (ii), the following sub-clause shall be inserted, namely:- “(iii) Shell Type Waste Heat Boilers(un-fired) :- (a) Shell type waste heat boilers (unfired), on completion of a life of twenty-five years, shall be non destructively tested by a Remnant Life Assessment Organisation approved by Central Boilers Board. (b) Pressure parts, including, shell, endplates, stand pipes, of such boilers, shall be inspected by ultrasonic testing, magnetic particle testing and dye penetrant testing. (c) If results are acceptable as per the standards laid down by the Central Boilers Board, a certificate shall be issued by the Chief Inspector or Director of Boilers, as the case may be, for extending the life of the boiler for a further period of twelve years or such less period as recommended by the Remnant Life Assessment Organisation. (d) The working pressure of such boilers may be reduced on the recommendation of the Remnant Life Assessment Organisation. (e) The assessment or remnant life by non destructive testing shall be carried out thereafter every twelve years by a Remnant Life Assessment Organisation approved by the Central Boilers Board and the agency shall work in close coordination with the office of the Chief inspector or Director of Boilers, as the case may be. Note: (1) It shall at the option of the owner to opt for the provisions of Para(i) or para (ii) above or opt for the Remnant Life Assessment of boiler as per para (iii). (3) Wherever, it is not possible to carry out non destructively testing of boiler for Remnant Life Assessment, provisions of para (i) or para (ii) shall be applicable.”; 15. In the principal regulations, in regulation 393, in clause (d), after the words, figures and letter “prescribed in regulation 385A”, the following words, letters and figures shall be inserted, namely:- “ subject to a maximum of Rs. 50,000.” . 16. In the principal regulations, in regulation 395, in clause (b) ,─ (i) in sub-clause (i) for the letters and figures “Rs 5,000 ”, the following letters and figures shall be substituted, namely:- “Rs. 500” ; (ii) in sub-clause (ii) for the letters and figures “Rs 1,000 ”, the following letters and figures shall be substituted, namely:- “Rs. 500.” . 17. In the principal regulations, for regulation 395C, the following regulation shall be substituted, namely:- “395C. Inspection fee for Valves and Flanges.─ (1) Subject to a minimum inspection fee of Rs. 600 per inspection, the fees for inspection of valves shall be charged as under:- (a) Upto 25 mm Rs. 15 per piece. (b) Above 25 mm and upto 100 mm Rs. 45 per piece. (c) Above 100 mm and upto 250 mm Rs. 270 per piece. (d) Above 250 mm Rs. 720 per piece. (2) Fees for inspection of flanges shall be charged as under:- (i) For forged and cast flanges: (a) upto and including 25 mm for a batch of 50 or part thereof Rs. 225 (b) upto and including 25 mm for a batch of 100 or part Rs. 390 thereof (c) over 25 mm upto and including 50 mm for a batch of 50 or Rs. 435 part thereof[भाग II—खण् ड 3(i)] भारत का रािप् : असाधारण 15 (d) over 50 mm upto and including 100 mm for a batch of 25 or Rs. 435 part thereof (e) over 100 mm upto and including 250 mm for a batch of 10 Rs. 465 or part thereof (f) over 250 mm for a batch of 5 or part thereof Rs. 540 (ii) For plate flanges: The fees shall be charged at half the rate as charged for forged and cast flanges .”. 18. In the principal regulations, for regulation 395G, the following regulation shall be substituted, namely:- “395G. The inspection fee for Spares and boiler components.-(1) The inspection fee for all types of coils, namely, economiser coils, superheater coils, reheater coils, shall be charged on the basis of surface area as provided in regulation 385A. (2) For inspection of tube and tube-bends, the fee shall be charged at the rate of Rs. 10 per meter subject to a minimum of Rs. 500.”. 19. In the principal regulations, in regulation 525, after clause (e) the following clause shall be inserted at the end, namely:- “ (f) If the requirements of provisional order specified under clause (e) are not fulfilled, fresh provisional order shall be issued subject to a maximum period of twenty four months from the date of issue of first provisional order, without any subsequent inspection and payment of fee.”. 20. In the principal regulations, in Form I, under the heading “REQUISITE AREA OF SAFETY VALVES”, under the sub-heading “ For superheated steam”, for the existing entry, the following shall be substituted, namely:- “ .”. 21. In the principal regulations, for APPENDIX JB, the following shall be substituted, namely:- “APPENDIX JB [See regulation 376(fff)] A. Waste Heat Boilers (Fired) upto twenty years of age used exclusively in continuous process plant. (1) For Waste Heat Boilers (Fired) up to twenty years of age used exclusively in continuous process plant, at the expiry of twelve months and at twenty four months from the date of inspection carried out in accordance with the procedure provided in regulation 390 and certification of fitness issued by the concerned Competent Person in the State, and having satisfied with the operation records as given below received alongwith application in Form XIX duly filled in shall be allowed for running for another period of twelve months:— (a) Operation data for superheater and reheater temperature excursions from the output of Data Acquisition System (DAS) or operation data for superheater temperature excursions maintained in the log sheet temperature record; (b) History of shut downs during the previous year with their causes and actions taken; (c) Records of any Non-Destructive test carried out on the boiler pressure parts during the year; (d) Water quality to the boiler is maintained as per the requirement of such boilers and on line data of the quality be provided through Data Acquisition System (DAS) or through water quality record logbook maintained at plant or at source of water; (e) Boiler tube failure record (location, number of tubes repaired/replaced). (2) Inspection shall be carried out by the concerned Competent Person at the expiry of thirty six months as provided in regulation 390. (3) In case of shutdown of fifteen days or more any time before the expiry of certification period and after six months of the certification, Competent Person shall be duly informed so that inspection can be scheduled during the said shutdown period. B. Waste Heat Boilers (Unfired) up to twenty years of age used exclusively in continuous process plant. (1) For Waste Heat Boilers (Unfired) up to twenty years of age used exclusively in continuous process plant, at the expiry of twenty four months from the date of inspection carried out in accordance with the procedure provided in16 THE GAZETTE OF INDIA : EXTRAORDINARY [PART II—SEC. 3(i)] regulation 390 and certification of fitness by the concerned Competent Person in the State, and having satisfied with the operation records at paragraph “A”, shall be allowed for running for another period of twenty-four months. (2) Inspection shall be carried out by the concerned Competent Person at the expiry of forty-eight months as provided in regulation 390. (3) In case of shutdown of fifteen days or more any time before the expiry of certification period and after six months of the certification, Competent Person shall be duly informed so that inspection can be scheduled during the said shutdown period. C. Waste Heat Boilers (Fired) more than twenty years of age used exclusively in continuous process plant. (1) Boiler more than twenty years of age shall continue to be subjected to inspection as provided in regulation 390 every year to the satisfaction of the concerned Competent Person in the State. (2) If Remnant Life Assessment is carried out on the boiler as per the provisions of these regulations and is found satisfactory, then procedure as given under paragraph 'A' shall be applicable. D. Waste Heat Boilers (Unfired) more than twenty years of age used exclusively in continuous process plant. (1) Boiler more than twenty years of age shall continue to be subjected to inspection as provided in regulation 390 every year to the satisfaction of the concerned Competent Person in State. (2) If Remnant Life Assessment is carried out on the boiler as per the provisions of these regulations and is found satisfactory, then procedure as given under paragraph 'B' shall be applicable.”. [F. No. P-30011/1/2020-Boilers] T. S. G. NARAYANNEN, Secy., Central Boilers Board Note:- The principal regulations were published in the Gazette of India, vide, number S.O. 600, dated the 15th day of September, 1950 and last amended vide G.S.R.123(E), dated the 17th February, 2020. Uploaded by Dte. of Printing at Government of India Press, Ring Road, Mayapuri, New Delhi-110064 and Published by the Controller of Publications, Delhi-110054.

Continue your research